OK, so i tried to flash parandroid and give me a error, my phone can enter download mode, but no in recovery, i tried to flash stock rom but with no luck it freeze at get pit for mapping if anyone can help it would be great, i need a good PIT file and a stock rom. thanks my s3 is 16 gb
alexmitu1234 said:
OK, so i tried to flash parandroid and give me a error, my phone can enter download mode, but no in recovery, i tried to flash stock rom but with no luck it freeze at get pit for mapping if anyone can help it would be great, i need a good PIT file and a stock rom. thanks my s3 is 16 gb
Click to expand...
Click to collapse
Try flashing the emergency recovery from here >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << you will need a pit file which is in the 4.1.2 download. You will need to flash the 4.3 rom in the thread if you have at any point been on a 4.3 stock rom because of efs issues..
tallman43 said:
Try flashing the emergency recovery from here >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << you will need a pit file which is in the 4.1.2 download. You will need to flash the 4.3 rom in the thread if you have at any point been on a 4.3 stock rom because of efs issues..
Click to expand...
Click to collapse
i tried it with no luck, still the same thing odin stop at get PIT for mapping
Here is what odin say:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..(here it's stay freezed and after a few minutes just fail)
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone can help?
alexmitu1234 said:
i tried it with no luck, still the same thing odin stop at get PIT for mapping
Here is what odin say:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..(here it's stay freezed and after a few minutes just fail)
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone can help?
Click to expand...
Click to collapse
Usually Complete(Write) operation failed is not a good sign and can be corrupt partitions or emmc failure. You could try changing usb ports (yes this as worked for some people) also try a different version of Odin I have always found Odin 1.85 good. To be honest it's not looking too good.
tallman43 said:
Usually Complete(Write) operation failed is not a good sign and can be corrupt partitions or emmc failure. You could try changing usb ports (yes this as worked for some people) also try a different version of Odin I have always found Odin 1.85 good. To be honest it's not looking too good.
Click to expand...
Click to collapse
i tried with Odin v 1.85 with no luck now it's just stuck at get pit for mapping it doesn't advance anymore here it's a picture with Odin:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Only a couple of things left to try:
Try flashing just a BLFB bootloader (search this forum for an Odin version)
Try removing the battery once Odin is connected.
If both the above fail then you have a brick, time for a new motherboard/phone.
boomboomer said:
Only a couple of things left to try:
Try flashing just a BLFB bootloader (search this forum for an Odin version)
Try removing the battery once Odin is connected.
If both the above fail then you have a brick, time for a new motherboard/phone.
Click to expand...
Click to collapse
ok,i tried with blfb bootloader and i can enter back in the recovery,i flashed 4.1.2 with bootloader, pda, phone, csc and a PIT file almost flashed but in the end has failed now it's again like first time, only with download mode and odin stuck a get pit for mapping so i think i need a new motherbord
Related
Iv rooted and flashed my S2 Using Odin. And now unable too connect to PC via USB. is there anyway of reflashing the phone to 2.3.6 from 4.0.3 Using Odin in Download Mode.
b33v3r said:
Iv rooted and flashed my S2 Using Odin. And now unable too connect to PC via USB. is there anyway of reflashing the phone to 2.3.6 from 4.0.3 Using Odin in Download Mode.
Click to expand...
Click to collapse
Yes
But how are you going to flash if you have no USB mode .
Search might help .
jje
I can get in into DOWNLOAD Mode using ODIN and the phone will connect
b33v3r said:
I can get in into DOWNLOAD Mode using ODIN and the phone will connect
Click to expand...
Click to collapse
Flash a stock rom as per all the threads posts faqs and guides .
jje
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
b33v3r said:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
Click to expand...
Click to collapse
Try this guide and download the right firmware you need. http://forum.xda-developers.com/showthread.php?t=1075278
Cheers!
b33v3r said:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
Click to expand...
Click to collapse
This sounds like the .tar file you are using is corrupted maybe. You may need to re-download it.
What file did you download and where did you get it from? What guide are you following?
Problem sorted yay
wisconsindesi said:
Try this guide and download the right firmware you need. http://forum.xda-developers.com/showthread.php?t=1075278
Cheers!
Click to expand...
Click to collapse
ahah silly me was trying to flash using i9000 stock sorted now using the right stock rom
b33v3r said:
ahah silly me was trying to flash using i9000 stock sorted now using the right stock rom
Click to expand...
Click to collapse
Yikes. You're lucky you didn't do some serious damage to your phone.
For doing this downgrade, do you need to use the PIT or something else?
Or just the standard ODIN config?
Is just this or more (http://forum.xda-developers.com/showthread.php?t=1075278):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Also, could I just use CWM to flash... lets say CheckROM (http://checkrom.com/download/)?
this is my first post.
how do i flash using Odin the file that i have downloaded which is superatmos_kernel_v2.2.tar. do i open the file with PDA only and flash it? or there are some other ways...
any inputs will be appreciated... sorry for noob question.. im just new here... and hoping somebody could help me.
adelbertheaven said:
this is my first post.
how do i flash using Odin the file that i have downloaded which is superatmos_kernel_v2.2.tar. do i open the file with PDA only and flash it? or there are some other ways...
any inputs will be appreciated... sorry for noob question.. im just new here... and hoping somebody could help me.
Click to expand...
Click to collapse
Your question is really way off topic.
Are you first sure the .tar is correct for your phone?
You should ask and read the instalation instructions from the developer first.
Hi guys, i can't get past my booting screen. (yellow triangle).
I flashed this file (below) for root acces. Everything in Odin was OK.
CF-Root-SGS2_XW_XEN_LP7-v5.4-CWM5.tar
But hey! It didn't get past the screen, no matter what.
I already tried to flash the siyah kernel etc. (Odin was OK again).
And when I try to flash a stock rom from sammobile it fails in Odin.
What can I do???
The sticker on the phone chassis under the battery; what does it say ?
Model: GT-I9100
SSN: -I9100GSMH
fabianbb said:
Model: GT-I9100
SSN: -I9100GSMH
Click to expand...
Click to collapse
STEP 1: Flash this using ODIN: http://stockroms.net/file/GalaxyS2/GT-i9100/ICS
STEP 2: Flash this rooted kernel: http://downloadandroidrom.com/file/GalaxyS2/kernels/ICS/CFRoot
Make sure that u tick PDA in ODIN...
ctg60000 said:
STEP 1: Flash this using ODIN: ttp://stockroms.net/file/GalaxyS2/GT-i9100/ICS
STEP 2: Flash this rooted kernel: ttp://downloadandroidrom.com/file/GalaxyS2/kernels/ICS/CFRoot
Make sure that u tick PDA in ODIN...
Click to expand...
Click to collapse
Odin fail at step 1.
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Three things come to mind:-
1) Your NAND is stuffed. Barfing at "NAND write start' is a bit of a tell.
2) When you're doing your Odin flash, are you checking in Windoze Task Manager that Kies/any of its processes aren't running, and if they are, killing those processes ?
3) The rom/kernel packages you've downloaded could be corrupted/damaged. I had this problem when I first got my phone; at one stage I had to DL a rom from a net cafe because every package I was downloading from home ended up with a corrupt archive (files within the zip/tar missing or damaged). Try downloading a rom from a different internet connection at another location/on another network/carrier to rule this in/out.
fabianbb said:
Odin fail at step 1.
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
can u upload screenshot of the odin after selecting the ROM file
After selecting the ROM file? There's nothing special to see yet. Just the PDA is marked. (with the file name on the right.)
And just Auto Reboot and F Reset Time are marked, nothing else.
Maby it is a NAND write issue, what to do about it? And Odin fails with every rom I try. Kernels are just flashing OK.
If the NAND is stuffed, it's a motherboard replacement job. Do what I suggested; download a full rom using a different internet connection.
MistahBungle said:
If the NAND is stuffed, it's a motherboard replacement job. Do what I suggested; download a full rom using a different internet connection.
Click to expand...
Click to collapse
I don't get it? Can you explain a bit more? What do you mean with a full ROM?
The rom you downloaded from Sammobile, download it again. From another internet connection at another location.
MistahBungle said:
The rom you downloaded from Sammobile, download it again. From another internet connection at another location.
Click to expand...
Click to collapse
I don't have quick acces to another computer today, but can you explain why that should help?
fabianbb said:
I don't have quick acces to another computer today, but can you explain why that should help?
Click to expand...
Click to collapse
Because your original download may have been corrupt. He already explained when he said:
MistahBungle said:
3) The rom/kernel packages you've downloaded could be corrupted/damaged. I had this problem when I first got my phone; at one stage I had to DL a rom from a net cafe because every package I was downloading from home ended up with a corrupt archive (files within the zip/tar missing or damaged). Try downloading a rom from a different internet connection at another location/on another network/carrier to rule this in/out.
Click to expand...
Click to collapse
ctomgee said:
Because your original download may have been corrupt. He already explained when he said:
Click to expand...
Click to collapse
But my kernels are flashing ok. Is it still possible then?
EDIT:
I tried this one:
http://sourceforge.net/projects/alliancerom/files/I9100/AllianceROM-I9100-FRAOSP-ICS-RE.zip/download
also with Pit sile, still fails.
First attempt, only PDA:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Second attemt, PDA + pit file (and repartition)
I think it's a problem with the NAND write?
Shall I try this?
http://forum.xda-developers.com/showthread.php?t=1457458
I really need a fix. Can I just do a factory reset or something??
Are you plugged from the phone into a port directly into a port on the computer? Not using a USB hub or a port pass-through on a keyboard or monitor? Have you tried another cable?
Why is a galaxy note listed in your pics?
theunderling said:
Why is a galaxy note listed in your pics?
Click to expand...
Click to collapse
I wondered the same thing. I then downloaded the same version of Odin, (1.87) and surprisingly it appears it is hard-coded into the header of that version.
ctomgee said:
I wondered the same thing. I then downloaded the same version of Odin, (1.87) and surprisingly it appears it is hard-coded into the header of that version.
Click to expand...
Click to collapse
This, it's hardcoded. No wrong drivers etc.
Please guys! I need a fix! ((
Service centre. Either the phone's borked or user error somewhere along the line, and this will be impossible for anyone here to pinpoint because we're not there with you.
Hi
I have searched the forum and various others but still could not solve my problem. SO please bare with me for 5 mins to read the following.
I have recently updated to Wanam's latest V5.3 XXELLA but over night it rebooted and stuck in a bootloop. so what i did was recovery wipe everything including dalvik cache BUT still stuck in bootloop. SO again i went back on the pc and flash the stock official XXELLA again bootloop again. I have found out some people might need to go into recovery and wipe everything after the official flash. BUT again still stuck in bootloop.
I honest don't remember ticking repartition but now when i try to flash ANYTHING it says the following:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXELLA_I9300OXAELLA_742798_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I have gone as far as finding PIT file from previous thread try to flash it but it just stucks at this forever:
I have tried the following 3 files from http://www.droidevelopers.com/f363/11722-[download]-ops-pit-files.html
GT-I9300_mx_20120220.zip
GT-I9300_mx_20120322.zip
GT-I9300_mx_20120329.zip
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
Please anyone if could shine a light on me on where to go. now when im in download mode this is what i see:
FACTORY MODE
PRODUCT NAME:
CUSTOMER BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
SO i have no model number and no boot and not flashable and this is all i will see when i power it up
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
STILL REVIVABLE?OR IS IT COMPLETELY DEAD?!
Believe this is another case of sudden death syndrome (eMMC failure)... you'll have to return it to a samsung service centre.
Sent from my GT-I9300 using Tapatalk 2
beaver2233 said:
Believe this is another case of sudden death syndrome (eMMC failure)... you'll have to return it to a samsung service centre.
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
is there nothing i can do apart from returning it to samsung? because the thing is i moved from uk to china and well if im being honest people here charge you for whatever they do. so you could say there is not such thing as warranty if you know what i mean. so i will want to fix it myself if possible.
if it is the sudden death syndrome, it is hardware failure, so no way to fix it yourself (not through software flashes etc) - someone else might need to confirm this, but seems to be the problem you're facing.
Sent from my GT-I9300 using Tapatalk 2
Custom rom + bootloop .
Its not dead looks like user or something has lost PIT partition .
As it stands it will fail warranty . Its not dead and download mode shows non stock firmware .
jje
so what do i need to do to revert it?
many thanks
hi! i would like to ask how's your phone? did you solve the problem of it? we have same situation i tried to flash different pit files but with no success. tried to flash official rom but it is still looking for pit file.
different pit files? flashing a wrong one kills the phone, there's nothing you can do.
Okay so here's the thing:
I installed clockworkmod 10.1 on my Samsung Galaxy S3 (UK version) the other day it worked fine however it then froze. I turned it off and then when I proceeded to turn it back on I was greeted with a white screen. I have tried to access recovery mode however the same white screen is just shown.
Although I cannot access recovery mode download mode is accessible however when I try to use Odin to flash a rom an error is shown saying
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
I have tried many different pit files and I don't know whether I have just got the wrong one!
Please help!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Can you get into recovery?
I can't get into anything except download mode!
If you can't may I suggest you try flashing one of the low ship formatted from this thread, it should put you back to your stock original firmware
http://forum.xda-developers.com/showthread.php?t=1796062
Low ship I9300 firmware for flashing with PIT. (three files firmware)
Calumt6 said:
Okay so here's the thing:
I installed clockworkmod 10.1 on my Samsung Galaxy S3 (UK version) the other day it worked fine however it then froze. I turned it off and then when I proceeded to turn it back on I was greeted with a white screen. I have tried to access recovery mode however the same white screen is just shown.
Although I cannot access recovery mode download mode is accessible however when I try to use Odin to flash a rom an error is shown saying
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
I have tried many different pit files and I don't know whether I have just got the wrong one!
Please help!
Click to expand...
Click to collapse
Your phone is basically screwed mate
stupidly will be met by sarcasm
Have you tried flashing a parted firmware with a pit file?
http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
If one of those don't work, then I don't know.
Correct me if i am wrong but im prerty sure flashing an incorrect pit file bricks the phone. You can take it to a service centre but its a paid for repair.
Vengeance
Sent from my GT-I9300 using xda app-developers app
correct
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
aminrezaya said:
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
Click to expand...
Click to collapse
I assume flashing a stock ROM with a pit file didn't work? nothing you can do
aminrezaya said:
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
Click to expand...
Click to collapse
SDS imho. Nothing you can do about. Send it to Service Point.
Sent from my GT-I9305 using xda app-developers app
djembey said:
SDS imho. Nothing you can do about. Send it to Service Point.
Sent from my GT-I9305 using xda app-developers app
Click to expand...
Click to collapse
I live in a country which has no service point... what can I do?
Any solution ? no product name when it enter to downloading mode
aminrezaya said:
I live in a country which has no service point... what can I do?
Any solution ? no product name when it enter to downloading mode
Click to expand...
Click to collapse
have you tried flashing anything with odin or not? if it fails, there is nothing you can do
Yes I tried 4.1.2 one file but it shows there is no PIT partition
so have you tried flashing a pit file?
Okay so I tried everything and nothing worked!
I thought I'd risk it and send it to Samsung to fix.
They collected on Tuesday, fixed on Wednesday, then returned on Thursday, I was amazed!
Thanks for all your replies and suggestions though
I ran WLSS Stock Rom with Kernel for some time
Yesterday I updated Google Search, the phone froze -> rebooted
Sine then about 20 times the phone came up froze and shutdown
Without missing a beat I thought it was a wonderful opportunity to flash the new Stock WLSW
I kill all of the kies processes and and tried to flash and it always fails !
Tried Odin 3.04, 1.85 and even tried reverting to WLSS with the same result....
Help someone...........:crying:
Now I can ONLY go to Download mode, there is now recovery.
When I try to boot normally I get a screen the tell's me :
Firmware upgrade encountered
an issue, Please select
recovery mode in Kies & try again.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Odin Screen Shot :
Odin log :
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLSW_I9100XXMS2_I9100XEULS5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Stock Rom source :
http://forum.xda-developers.com/showthread.php?t=1544487
Philz kernel source:
http://forum.xda-developers.com/showthread.php?t=1877270
For the users who search with the same symptoms TRY THIS ! :
The Issue is resolved !
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasnt able to flash !
10Q you all !
That pic on the screen means it's already in download mode (forced download mode). You need to search for Hopper8's 'Odin won't work' thread. I'd be surprised if you can't successfully flash with the info/stuff to try in that thread.
MistahBungle said:
That pic on the screen means it's already in download mode (forced download mode). You need to search for Hopper8's 'Odin won't work' thread. I'd be surprised if you can't successfully flash with the info/stuff to try in that thread.
Click to expand...
Click to collapse
if you're referring to this : http://forum.xda-developers.com/showthread.php?t=2345831
I did everything there but PIT or a costume rom/kernel....
This is the next step?
So you did everything, including the flashing of the 3 part firmware? Assuming you have an I9100 anyway.
Don't flash a pit (I'd like to say ever) but at least not now.
You can try flashing Siyah v6 as linked in the guide. I'd continue to try to flash JB leak, the 3 part firmware.
Sent from a galaxy far, far away
Hopper8 said:
So you did everything, including the flashing of the 3 part firmware? Assuming you have an I9100 anyway.
Don't flash a pit (I'd like to say ever) but at least not now.
You can try flashing Siyah v6 as linked in the guide. I'd continue to try to flash JB leak, the 3 part firmware.
Sent from a galaxy far, far away
Click to expand...
Click to collapse
Isn't the 3 part firmware is with a PIT?, i didnt try this one,
And Siyah fails also......
Code:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> zImage
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
The 3 part firmware consist of : Firmware + CSC + Modem.The good is with the 3 part firmware is that it does a factory reset automatically.BTW,I've heard so many issues like this,that people on stock ROM were updating apps/browsing internet,then it suddenly froze and Odin never works.I recommend not to use Samsung firmware,or at least not 100% original.Use a custom stock ROM.and also,if siyah failed too,then I think your only options are: 3 part firmware, .PIT or nothing
GamingDj said:
The 3 part firmware consist of : Firmware + CSC + Modem.The good is with the 3 part firmware is that it does a factory reset automatically.BTW,I've heard so many issues like this,that people on stock ROM were updating apps/browsing internet,then it suddenly froze and Odin never works.I recommend not to use Samsung firmware,or at least not 100% original.Use a custom stock ROM.and also,if siyah failed too,then I think your only options are: 3 part firmware, .PIT or nothing
Click to expand...
Click to collapse
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasn't able to flash !
10Q you all !
Idan.lv said:
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasnt able to flush !
10Q you all !
Click to expand...
Click to collapse
to flush= clean toilet/wc
to flash= install firmware
As a grammar nazi I couldn't miss this one.
GamingDj said:
to flush= clean toilet/wc
to flash= install firmware
As a grammar nazi I couldn't miss this one.
Click to expand...
Click to collapse
what ever do you mean....?
thank you for the correction
Dyslexia + No a native speaker = comedy