Really need some help with this.
Looked around in the system and found a file that I thought would maybe have some answers.(audio_effects.conf)
Is there any way to reduce the global audio volume level by adding/changing anything in the /system/etc/audio_effects.conf or build.prop
Changed
audio.speaker.voice.
audio.earpiece.voice
audio.earpiece.voice
in build.prop but no change in the output level.
Would prefer build .prop tweaks as the process needs to be repeted for quite a few devices.
Device is a rooted Cortex A8 Generic Android tablet running 4.0.4.
Thank You in advance
Related
Is there a way to increase my phone's volume?
It sound very low after updating my android version into kitkat.
Do I have to flash something? Help pls.
Shichiro said:
Is there a way to increase my phone's volume?
It sound very low after updating my android version into kitkat.
Do I have to flash something? Help pls.
Click to expand...
Click to collapse
use viper 4 android and select neon cortex (last option in list install drivers)
and change all decibels to max
Hello
Lien : http://pan.baidu.com/s/1mgwj4RQ
Here is a tool to control the cpu, I install the apk and then flash the ZIP file download, it works because I have seen first note of the changes in the behavior of CPU ...
It is possible to translate and adapt to the MT6589? thank you
ovme said:
Hello
Lien : http://pan.baidu.com/s/1mgwj4RQ
Here is a tool to control the cpu, I install the apk and then flash the ZIP file download, it works because I have seen first note of the changes in the behavior of CPU ...
It is possible to translate and adapt to the MT6589? thank you
Click to expand...
Click to collapse
Are you sure that this is a tool controling CPU?
All I can see is memory-something control...
No CPU tweaks whatsoever...
When have played with the tab above, it is possible to activate the 4 cores at once, even if the cpu made minimal operations,
so I think it influences the behavior of the cpu
Hi,
This is what I have found on chinese websites.. They say that there are four options (and maybe the fifth one i "OFF").
1/ balanced (battery / performance)
2/ performance+
3/ battery+
4/ maximum battery (cpu is keeped at 750MHz)
What a shame that it is not OVERCLOCKING tool
ovme said:
Hello
Lien : http://pan.baidu.com/s/1mgwj4RQ
Here is a tool to control the cpu, I install the apk and then flash the ZIP file download, it works because I have seen first note of the changes in the behavior of CPU ...
It is possible to translate and adapt to the MT6589? thank you
Click to expand...
Click to collapse
try this, its english ver foreground control the backtround init.d files (01MTKTweakCPU, 02MTKTweakRam, 03MTKTweakElse)
I can't recall where i dl it, thanks to the moshi
to verify it it works, you will see /data contains mtktweakxxxx log files.
here you go, the MT6589 & MT6589T. the scripts diff only.
Hello,
I'm not sure if this is the right sub-forum but I think this one isn't the worst choice.
I have a Radxa Rock Pro-Board running with Android 4.4.2. This board has GPIO-Pins for UART-Communication. I connected an UART-GPS-Device to it and can see incoming NMEA-Data on /dev/ttyS3. The Problem: How to configure Android to listen on GPS-Data on this interface?
I found some threads about GPS-Infrastructure in Android which says something about drivers (do I really need one in Android when it's a UART-one-way-Communication?), configuring the build.prop ("ro.android.gps.provider = ttyS3" which I did without success) and daemons like gpsd or glgps (which isn't included in a new build Android from radxa sources and is it really needed, or is this a can and not must have?).
So my question is, where does Android listen do GPS on default and how to change it to ttyS3?
Thanks in advance
geifawkes
Hello to all ,
Im newbie on forum and android too. I was an iPhone user and i forced to buy an Android phone so that was m4 Aqua.
I made somethings which i didnt figure out how to solve. I hope you guys help me.
1. I rooted with tutorial on M4 General forum with flastool64, it was okay.
2.I Removed useless widgets and made my Aqua faster.
So problem is, I flashed two things.
* Loud mode sound boster
*Z5 Premium Graphic enchament.
-Stereo speakers working but so loud and after %70 volume, it stays same until reach %100
No Settings for Z5 Graphics and No Settings for dolby or something like that.
So how can i figure out this ? My model is E2303 8GB Model, Latest stock version Android 5.
Don't flash that Loud mode sound booster, just use the xml one
I think your rom has to be deodexed to get the z5 stuff, you can use one of @yash989 works to get the things you want
And you can reflash only your system using flashtool to remove what you've done wrong
Hello guys , I'm on latest Xiaomi EU ROM and for some reason I feel like the sound output is not as good as the stock global ROM ,
So I wanted to tweek the mixer_path.xml file ....but I don't know which line to edit .....can someone help me with it ....
Any help will be appreciated
DRC enabled?
rsrohit315 said:
Hello guys , I'm on latest Xiaomi EU ROM and for some reason I feel like the sound output is not as good as the stock global ROM ,
So I wanted to tweek the mixer_path.xml file ....but I don't know which line to edit .....can someone help me with it ....
Any help will be appreciated
Click to expand...
Click to collapse
I think that it is caused by DRC.
In /vendor/etc/audio_policy_configuration.xml, there may be a line containing 'speaker_drc_enabled="true"'. Edit the line to replace "true" with "false" and reboot. Then, deep compression on the sound output will go away.
Note: 'speaker_drc _enabled' contains 'speaker', but it affects all audio output, e.g. internal speaker, 3.5mm jack wired, buetooth and USB DAC (even using a proprietary driver) earphones, etc.