Dear all hope you all are good i yesterday while updating firmware software from phone option after restart my phone is stucked at flash mode i even loaded stock firmware usint flashtool everything done ok but when i unplug my mobile its still in off condition even pressing power button removing battery and placing again and pressing power but nothing on screen but when i plug my usb to pc without pressing back button it shows that phone is in flash mode many times i removed and plugged but same issue i think it stuck at flash mode please help...
kashifmac2005 said:
Dear all hope you all are good i yesterday while updating firmware software from phone option after restart my phone is stucked at flash mode i even loaded stock firmware usint flashtool everything done ok but when i unplug my mobile its still in off condition even pressing power button removing battery and placing again and pressing power but nothing on screen but when i plug my usb to pc without pressing back button it shows that phone is in flash mode many times i removed and plugged but same issue i think it stuck at flash mode please help...
Click to expand...
Click to collapse
thanks alot guys i found the solution here below
xpneov said:
never mind guys.. i found the reason of brick and solution too on the below link
http://forum.xda-developers.com/showthread.php?t=1598160
Click to expand...
Click to collapse
thank you so much same issue i faced and resolved now using this information whatever how i unlocked the bootloader i don't care my phone is restored and next time i will be careful regarding OTA update.
once again thanks buddy coz i searched alot but found it here in your reply
hi guys, i just create an account for this.i tried to flash cwm 6.0.4.4 on my xgo, it said that flashing completed then i reboot the phone. but it's not booting up it's completly dead. no screen,no vibrate, only showing red led when i connect it to pc or wall charger. i can't get in to flashmode or fasboot. i've read lot of similar thread, but none solve my problem. wih you guys can solve it. thanks
Where did you find the recovery?
Sent my Xperia P running MoonWalker 7.5
AndroidNoob69 said:
Where did you find the recovery?
Sent my Xperia P running MoonWalker 7.5
Click to expand...
Click to collapse
sorry, i'm forgot. i deleted my history..
but i got it in this forum
can you please provide some info about your device, like :
what is the ROM u were using ?
is bootloader locked or unlocked?
was your device rooted ?
---------
what happens when you press power+vol up till single vibration (see any SONY logo ?) , or the phone is not responding to any reset ?
was your phone charged enough ?
if yes,
is your screen alive when you try to start your phone ? (LCD screen hasbacklit LED, is it working ?)
--------
and last one, did you grant SU permission during installation ?
setpam25 said:
hi guys, i just create an account for this.i tried to flash cwm 6.0.4.4 on my xgo, it said that flashing completed then i reboot the phone. but it's not booting up it's completly dead. no screen,no vibrate, only showing red led when i connect it to pc or wall charger. i can't get in to flashmode or fasboot. i've read lot of similar thread, but none solve my problem. wih you guys can solve it. thanks
Click to expand...
Click to collapse
deshx said:
can you please provide some info about your device, like :
what is the ROM u were using ?
is bootloader locked or unlocked?
was your device rooted ?
---------
what happens when you press power+vol up till single vibration (see any SONY logo ?) , or the phone is not responding to any reset ?
was your phone charged enough ?
if yes,
is your screen alive when you try to start your phone ? (LCD screen hasbacklit LED, is it working ?)
--------
and last one, did you grant SU permission during installation ?
Click to expand...
Click to collapse
i use CM11
bootloader unlocked
yes, it's rooted
nothing happen when i press every key combinations. just red led
setpam25 said:
i use CM11
bootloader unlocked
yes, it's rooted
nothing happen when i press every key combinations. just red led
Click to expand...
Click to collapse
is your device recognised when connected to pc ? if not, what exactly happens ? ( did you see it in status bar ? ) what is your OS of laptop ?
what happens when you connect it to a charger ?
deshx said:
is your device recognised when connected to pc ? if not, what exactly happens ? ( did you see it in status bar ? ) what is your OS of laptop ?
what happens when you connect it to a charger ?
Click to expand...
Click to collapse
no, nothing happen.
my os is windows 8.1
nothing happen when it connected to charger, just red led
U can try buying or make your own usb jig and force your phone to download mode, from there install your custom/stock rom. You can get your USB jig from ebay it ranges $3-6
Sent from my GT-I9505G using XDA Premium 4 mobile app
if your device was recognized in usb debugging mode with the flashtool, BEFORE the brick ON same win 8.1, then try getting into fastboot mode again. ( for win 8 support : http://forum.xda-developers.com/xperia-u/issues/guide-to-install-xperia-fastboot-driver-t2447283 )
- start flashtool
- remove phone from other devices. red LED should turn off.
- long press ( ~10sec ) power + vol up to do a hard reset. ( if possible )
- connect using power+vol up
- press 'flash' button, select fastboot.
if above process fails, try checking where or when it failed. try getting any error out of flastool.
-if you hear any sound in windows of " usb plugged in/out "( like plugging pen-drive in ) or flashtool showing any error ( related to drivers )
open device manager, and try connecting again. double click the device in the list when you connect the phone and check for drivers.
you can also try another usb port and/or another windows installation (preferably winXP).
if there is battery problem, u can charge your device for some time (20-30 min). when battery is drained completely, phone cannot boot up kernel and the phone charges in non kernel-governed mode. u see nothing on screen in this process.when battery is charged enough you can try connecting again.
if the phone is not recognized as a usb device to your computer( in any possible way ), then im afraid u might have messed up with the partition or the bootloader.
try getting help form CM11 devs or other devs on this post.
i am not an expert in hardware methods of recovering your device, HOWEVER, if the device somehow gets connected to pc, u may ask for help anytime.
(sorry for my english)
I have problem with my oppo r2001, my phone was bootloop and I was tried to fix it but it not works! all of the procedures have been tried. When i use SP flashtool v.5, i follow all procedure, but the problem when i was plugged my hh to pc, then few seconds later there was a sound like my phone has been unplugged. I'm sure it was not a problem on the cable USB, because it is a new cable. Then I supposed it will works if i flash fw with oppo recovery mode. But it cant get in recovery mode after press volume down+power(just OPPO word and "recovery mode" words in the left corner, and release the button the "recovery mode" words dissapeared).
So WHAT SHOULD I DO TO FIX MY PRECIOUS PHONE? PLEASE HELP ME
Same problem here... Bootloop with empty adb device and empty fastboot device. It is totally in deep ****. My current conclusion is to bring it to oppo service center to get emmc ic replaced. But i still hope to get a way around it.
Hello guys, i have sony xz1 g431, i bricked my phone when i try to install another rom of another device via twrp. Now my phone no light when connect to pc, no light when charging, flash tool doesnt recognize my phone. When i connect my phone to pc it only shows QUSB_BULK on my pc. I think it lost fastboot or something. I try hold down button, up button or both when connect to pc but still no light and nothing happen.
Please help me fix this problem or atleast some good suggestions to solve this problem. I will really happy for that. Thanks :crying:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
j4nn said:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
Click to expand...
Click to collapse
i have tried it but there's no light. I think it's dead :crying:
@Karl Einstein, have you tried both ways as suggested above?
Maybe you can examine what usb device appear (if any) in each of the described modes (tried to enter flash mode, tried to enter fastboot mode, tried to just plug the phone to usb without holding any button from power off state).
What happens if you try to enter recovery mode (twrp) - having your phone powered off, without usb connection, holding volume down and power, should enter twrp if you had it flashed before.
Do you get any vibration when hold the power button and.volume.key.up?
Karl Einstein said:
Hello guys, i have sony xz1 g431, i bricked my phone when i try to install another rom of another device via twrp. Now my phone no light when connect to pc, no light when charging, flash tool doesnt recognize my phone. When i connect my phone to pc it only shows QUSB_BULK on my pc. I think it lost fastboot or something. I try hold down button, up button or both when connect to pc but still no light and nothing happen.
Please help me fix this problem or atleast some good suggestions to solve this problem. I will really happy for that. Thanks :crying:
Click to expand...
Click to collapse
Well...I think your phone is dead...I'm really sorry to say that, but in this case, that is the only reasonable explanation.
Yesterday I flashed the GSI image, then tried to flash to eXistenZ, it just stuck in the startup interface. However, it can still enter flash mode and fastboot mode, I have no choice but to use the newflasher to re-flash the firmware, it will return to normal.
In general, Sony devices are hard to change bricks, unless the phone is a Japanese carrier's custom phone (generally can not unlock the bootloader, and can only flash some firmware).
I have seen users who have flashed CE firmware for the docomo version and then can't enter flash mode and fastboot mode.Unlike your device,her phone is totally dead...It can't be charged, and there is no prompt to connect to the computer.
If you can buy a motherboard from eBay or somewhere else,you can disassemble your phone,then replace the old motherboard.
Hope these helps.
Thank you guys for all your support. Finally i decided to skip this problem and i will buy a new device
TimCrownie said:
Well...I think your phone is dead...I'm really sorry to say that, but in this case, that is the only reasonable explanation.
Yesterday I flashed the GSI image, then tried to flash to eXistenZ, it just stuck in the startup interface. However, it can still enter flash mode and fastboot mode, I have no choice but to use the newflasher to re-flash the firmware, it will return to normal.
In general, Sony devices are hard to change bricks, unless the phone is a Japanese carrier's custom phone (generally can not unlock the bootloader, and can only flash some firmware).
I have seen users who have flashed CE firmware for the docomo version and then can't enter flash mode and fastboot mode.Unlike your device,her phone is totally dead...It can't be charged, and there is no prompt to connect to the computer.
If you can buy a motherboard from eBay or somewhere else,you can disassemble your phone,then replace the old motherboard.
Hope these helps.
Click to expand...
Click to collapse
Just a side note , why flash existenz on a gsi rom... As it is made for stock Sony only or did I just misread something..
I had the same issue before on my lenovo p2 it lost fastboot and download mode but the PC detect it as qusb bulk then Qualcomm USB h9008 I searched all solutions but no good I think it needs some kind of box to push the modes or change the mother board. So I changed to Sony instead of repair it
Karl Einstein said:
Thank you guys for all your support. Finally i decided to skip this problem and i will buy a new device
Click to expand...
Click to collapse
Sad to ear that...
I had the same issue with my previous Htc10.
As it was still under warranty, I have had to contact HTC support and told them that and OTA bricked it.
They accepted the issue and replaced the motherboard.
I was BL unlocked, rooted and custom rom when it happened and no issue with support as they had no mean to prove it ?.
If still under warranty try to contact Sony support and tell them the same story... Ota bricks my phone ?
lilbrat said:
Just a side note , why flash existenz on a gsi rom... As it is made for stock Sony only or did I just misread something..
Click to expand...
Click to collapse
I've flashed eXistenZ before flash GSI in my phone. I thought GSI image would cover my origin ROM like eXistenZ, so after flash GSI image in,I flash eXistenZ again.
j4nn said:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
Click to expand...
Click to collapse
I have the same issue. My sony xperia xz1 G8342 got sudden dead. (Before dead, I remember I disabled "Developer Mode"). Now its not response by any mean except charging sign when i connect to Power source or PC. Xperia Flashtool shows "device connected with USB debugging disabled".
So, How Can I enter flash mode or fastboot mode? Is My phone recoverable? Please Help.
Thanks
Yesterday I was struggling with my XZ1 Compact and came across this thread that gave me some light to get my mobile phone back.
I guess it's way late for Karl now but just in case, I'm sharing my experience. I was working on my device to get LineageOS 18, as I'm a total newbie with roms I followed the different articles that were posted on Getdroidtips for this particular case: Unlocked bootloader, flashed TRWP and installled lineageos. But then I realized it would be good to have Google Play for restoring my files and apps, but when tried to reboot into recovery mode to get Gapps flashed, Black Screen Of Death started.
After that
with the phone plugged to the pc it wasn't recognized as a device (so adb or fasboot where useless)
the only thing the phone reacted to was to press and hold power + volume up (either for reset or power off)
but no matter what, next boot again BSoD
Tried the Xperia Companion but it prompted that repair was not possible as bootloader was unlocked.
Eventually found this life saver
j4nn said:
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
Click to expand...
Click to collapse
From there, using fasboot I could reboot the device back with the LineageOS. I was still having issues with recovery boot but I'll post that on a different thread.
Thanks again to everyone for sharing thoughts and tips!
Hi, i have a xperia z2 totally unresponsive, no power button, no volume buttons, no red reset button, no power on any form but magnetic port, no testpoint function (testpoint connected to ground or plates or point near to upper screw or any other know ground point).
The whole thing started when i try to flash some custom LineageOS 16 for Sirius board!
I try to update TWRP from 3.0.2 to 3.3.1 and flash the rom with gapps for android 10. The rom in TWRP mode shows an error and stop flashing, then i try again with wipes and same error, i try gapps and same error, then i reboot to system and crash, good bye BOOT, SYSTEM and all.
No PC response too. It just power by putting into magnetic dock, just then the phone power on and stuck into SONY logo.
There is a form to get the phone back to life??
P.D.: Phone is bootloader unlocked with TWRP 3.0.2 succesfully installed. Works normally before try to install that Sh*t of rom. Stock Rom Android 6 (23.5.A.1.291), usb cable, buttons board and red reset button unresponsive.
Did you hear any sound from pc or see device manager refresh when you connect device? Or did you try another usb cable?
Try press red button when you see Sony logo then connect to pc with flashmod or fastboot (if it detectable first)
So You Flashed the rom on the 3.0 twrp?