Related
Photon Today in my hand in Italy..
Brand new...
Never activated on Sprint...
but when i turn on ...each time ask me activation for 4/5 minutes...and after start.. every time i have to choose correct band ecc....
and
After ota update 45.2.7... wifi not working!!
How to skip always this activation?...and solve wifi issues?
pagapervedere said:
Photon Today in my hand in Italy..
Brand new...
Never activated on Sprint...
but when i turn on ...each time ask me activation for 4/5 minutes...and after start.. every time i have to choose correct band ecc....
and
After ota update 45.2.7... wifi not working!!
How to skip always this activation?...and solve wifi issues?
Click to expand...
Click to collapse
Just flash a custom ROM to it
mrinehart93 said:
Just flash a custom ROM to it
Click to expand...
Click to collapse
Ok sir...
Rooted ...unlocked... cwm installed...
Which Rom ? Alien or starwars ?
No problem with English but will be great a Multilingual Rom for all international users...
pagapervedere
For the skipping sprint activation you also can freeze all apps with "sprint" (or sprint zone and sprintOmaDm as minimum) in the title via titanium backup.
They have a "stockish" rom that is in the development section that everyone is ranting about. By I personally am running the Alien ROM. which is okay. But I'd go with either Star Wars or the Stockish ROM myself. I'm gonna be flashing over the Stockish one tomorrow.
Thanks to all...
now i'm flashing Alien.....
after, if i'm not happy try others...
Good luck.
Flashing Alien rom will not skip the long network check on boot. Do not and i repeat do not freeze the Sprint zone as this causes a force close when it finishes the check upon reboot and causes it to check over and over again. (first hand experience of this)
Simple solution, put pbone into airplane mode before powering off, add the widget to your home screen. When you re boot knock it out of airplane mode and will connect to your network provider and no need to change any settings.
This was posted in another thread but cannot remember which one.
Sent from my MB855 using xda premium
ianford10 said:
Flashing Alien rom will not skip the long network check on boot. Do not and i repeat do not freeze the Sprint zone as this causes a force close when it finishes the check upon reboot and causes it to check over and over again. (first hand experience of this)
Simple solution, put pbone into airplane mode before powering off, add the widget to your home screen. When you re boot knock it out of airplane mode and will connect to your network provider and no need to change any settings.
This was posted in another thread but cannot remember which one.
Sent from my MB855 using xda premium
Click to expand...
Click to collapse
Arrived late..............
BIG BIG problem.....
Phone rooted
Phone unlocked correctly
Installed CWM-based Recovery 4.0.1.5 Photon 1.2 (flashed not APK)
ROM ZIP file inside ext sd (alien,star wars and stockish)
TURN OFF phone
RECOVERY start correctly...
Wipe OK
wipe cache OK
wipe Dalvin OK
Install Alien..
Reboot
All OK
Rom starts correct with boot animation ecc..
but after Running continously Contact Network (maybe for Sprint Activation)
then show me Hands free activation...
but when i type OK System Force close..application SprintOmaDm
and repeat each time same problem..
So system will not start....and blocked before entering in first setup...
PLEASE HELP ME..
Same thingh with other Roms (star wars and stockish)
^^ i am facing the same issue here.. any solution?
If your phone is unlocked then flash the full puddin SBF file using RSD. Make sure it's the big file and not the one that's around 1 - 2 mb. Once finished it will say fail, pop the battery and re boot. Should now work again and do the long network check but without force close. Then just use airplane mode before shutting down each time.
Again do not freeze or remove sprint zone, that is the cause of the force close, not the roms.
Maybe an easier way but that's what I had to do.
Sent from my MB855 using xda premium
Freezing SprintOmaDm disables the Sprint check. However, for some reason, the slide locks are disabled.
If there's a fix, I'd love to hear it...
ianford10 said:
If your phone is unlocked then flash the full puddin SBF file using RSD. Make sure it's the big file and not the one that's around 1 - 2 mb. Once finished it will say fail, pop the battery and re boot. Should now work again and do the long network check but without force close. Then just use airplane mode before shutting down each time.
Again do not freeze or remove sprint zone, that is the cause of the force close, not the roms.
Maybe an easier way but that's what I had to do.
Sent from my MB855 using xda premium
Click to expand...
Click to collapse
i can't find the pudding BIG!!!!!
i find it in other forums but links doesn't works.....(464MB)
Please help me to find it....
When i unlocked i used the 1MB pudding file...
Sure if works again i will put each time in aereo mode before turn off!!!!!
pagapervedere said:
i can't find the pudding BIG!!!!!
i find it in other forums but links doesn't works.....(464MB)
Please help me to find it....
When i unlocked i used the 1MB pudding file...
Sure if works again i will put each time in aereo mode before turn off!!!!!
Click to expand...
Click to collapse
Looks like the pudding_stock_unlock.sbf link is no longer available. I still have it on my machine but it weighs in at just under 2.5GB (silly me, its 404MB when zipped, uploading to FileFactory now)
Think your best option at present is to go back to basics. Firstly flash the stock recovery from here http://forum.xda-developers.com/showthread.php?t=1216143
Then download and flash the latest ota for rsd from here http://forum.xda-developers.com/showthread.php?t=1202666
Then go through the process of rooting/unlocking.
kk
ianford10 said:
Looks like the pudding_stock_unlock.sbf link is no longer available. I still have it on my machine but it weighs in at just under 2.5GB.
Think your best option at present is to go back to basics. Firstly flash the stock recovery from here http://forum.xda-developers.com/showthread.php?t=1216143
Then download and flash the latest ota for rsd from here http://forum.xda-developers.com/showthread.php?t=1202666
Then go through the process of rooting/unlocking.
Click to expand...
Click to collapse
ok now i download stock recovery 3,6mb
bur need to erase cwn recovery or just flash trough fastboot and overwrite it.?
than flash by rsd last update official...477mb?
let me know and many thanks to help me.
pagapervedere said:
kk
ok now i download stock recovery 3,6mb
bur need to erase cwn recovery or just flash trough fastboot and overwrite it.?
than flash by rsd last update official...477mb?
let me know and many thanks to help me.
Click to expand...
Click to collapse
Yes go through the process of erase recovery then flash the stock recovery, take note that it is .smg just in case you think its .img
Then get RSD fired up and select the official update, phone into rsd mode and wait for it to complete. If all goes well it will say you need to manually re boot your device.
Any probs let us know and will try our best
ianford10 said:
Yes go through the process of erase recovery then flash the stock recovery, take note that it is .smg just in case you think its .img
Then get RSD fired up and select the official update, phone into rsd mode and wait for it to complete. If all goes well it will say you need to manually re boot your device.
Any probs let us know and will try our best
Click to expand...
Click to collapse
sorry for my noobies...another question?
i must lock the bootloader too?
pagapervedere said:
sorry for my noobies...another question?
i must lock the bootloader too?
Click to expand...
Click to collapse
You can just to be on the safe side.
I flashed it once when i was unlocked and i received a fail to boot message. Forgot to re lock the bootloader yesterday and just flashed and worked with no issues.
Just to keep it safe yes
now i'm working...but this night i'll proceed...
i can't understand how it's possible that i received this error with all roms i flashed..
and i have NOT freezed never Sprint application...
i hope that, after the stock flash, to replace like new....
pagapervedere said:
now i'm working...but this night i'll proceed...
i can't understand how it's possible that i received this error with all roms i flashed..
and i have NOT freezed never Sprint application...
i hope that, after the stock flash, to replace like new....
Click to expand...
Click to collapse
Glad you are back up and running
So you did not freeze the sprint zone at all?
When i flashed the HomeBase Photon Stock rom it went through the network check, hit ok at the end and got a force close. Must admit that never happened with the Alien rom though.
This is why now i am only rooted. Installed the latest update and just rooted. Had too many issues with custom roms, to be honnest stock is very fast and i also use ADWLauncher EX. You can also freeze/unistall the bloatware if need be, there is another thread with a list of safe apps to remove, but not sprint zone lol
Heres the link for the full Pudding_Unlock.SBF file
I will say right now, I'm a total noob, and could have possibly picked the WORST device to try flashing from Verizon to Cricket, but I have SCOURED the internet, and the more I read, the more I do with this phone, the more confused I become.
I tried (and failed):
* Loading a custom PRL onto the phone with CDMA Workshop 2.7 (Phone will not load with QRST)
* Changing ANY data in the NAM/CDMA Configuration and have the phone remember
* Seeing if there might be a custom ROM available.
So my question is: WHERE DO I START!?
the1corrupted said:
I will say right now, I'm a total noob, and could have possibly picked the WORST device to try flashing from Verizon to Cricket, but I have SCOURED the internet, and the more I read, the more I do with this phone, the more confused I become.
I tried (and failed):
* Loading a custom PRL onto the phone with CDMA Workshop 2.7 (Phone will not load with QRST)
* Changing ANY data in the NAM/CDMA Configuration and have the phone remember
* Seeing if there might be a custom ROM available.
So my question is: WHERE DO I START!?
Click to expand...
Click to collapse
Well here is the post, that i made and they say it can be done remotely. http://forum.xda-developers.com/showthread.php?p=40669287 read carefully and I myself cant make QRST to even read from phone correctly and I have my msl code...
Sent from my ADR6410LVW using xda premium
24ky said:
Well here is the post, that i made and they say it can be done remotely. http://forum.xda-developers.com/showthread.php?p=40669287 read carefully and I myself cant make QRST to even read from phone correctly and I have my msl code...
Sent from my ADR6410LVW using xda premium
Click to expand...
Click to collapse
Since I've had so much free time with my phone, I actually got the thing flashed.
Between QPST and the right PRL, my Incredible 4G LTE is now capable of utilizing my talk and text. The last thing I have to do is program an APN for the phone, so my question has changed now.
After going under Settings -> Mobile Network -> Access Point Names -> Create New APN
I tried creating a new one but the default APN (VZWINTERNET) remains default and I can't seem to add any new APNs on the phone. I already have the settings for making the APN work, but does anyone know a fix for the phone not remembering new APNs?
the1corrupted said:
Since I've had so much free time with my phone, I actually got the thing flashed.
Between QPST and the right PRL, my Incredible 4G LTE is now capable of utilizing my talk and text. The last thing I have to do is program an APN for the phone, so my question has changed now.
After going under Settings -> Mobile Network -> Access Point Names -> Create New APN
I tried creating a new one but the default APN (VZWINTERNET) remains default and I can't seem to add any new APNs on the phone. I already have the settings for making the APN work, but does anyone know a fix for the phone not remembering new APNs?
Click to expand...
Click to collapse
is your phone rooted, s-offed ect... if so flash viperlte and you can add apns, if youd pm me i can write up a guide for people on how to flash
24ky said:
is your phone rooted, s-offed ect... if so flash viperlte and you can add apns, if youd pm me i can write up a guide for people on how to flash
Click to expand...
Click to collapse
No, and I figured I would have to. So now I'm working on rooting the phone unless you already know how.
So once I have it rooted, it's as simple as rewriting over the default APN?
the1corrupted said:
No, and I figured I would have to. So now I'm working on rooting the phone unless you already know how.
So once I have it rooted, it's as simple as rewriting over the default APN?
Click to expand...
Click to collapse
Yes but install a costom Rom, but backup ur stock first
Sent from my ADR6410LVW using xda premium
24ky said:
Yes but install a costom Rom, but backup ur stock first
Sent from my ADR6410LVW using xda premium
Click to expand...
Click to collapse
Run into a headache trying to get a custom bootloader going so I can kernel root and load the custom rom of choice (Venom LTE)
I tried to download the All-In-One kit from this site, but the link was broken
the1corrupted said:
Run into a headache trying to get a custom bootloader going so I can kernel root and load the custom rom of choice (Venom LTE)
I tried to download the All-In-One kit from this site, but the link was broken
Click to expand...
Click to collapse
Contact hasoon2000 via pm and let him know, but have you used my teams super cid tool or, mdmowers script.
Sent from my ADR6410LVW using xda premium
24ky said:
Contact hasoon2000 via pm and let him know, but have you used my teams super cid tool or, mdmowers script.
Sent from my ADR6410LVW using xda premium
Click to expand...
Click to collapse
So far, just completed this walkthrough: http://forum.xda-developers.com/showthread.php?t=1986346
Fingers crossed it all works and I can load my custom ROM.
EDIT/UPDATE: So I completed the full bootloader unlock! YAY! Now to try and load the Venom ROM. Ideally, everything will work after loading the new ROM.
So it turns out, I still can't root this phone.... I have unlocked the boot loader, but USB Fastboot doesn't appear.
I'd rather edit the post than make new posts. Fixed the damn thing. I can load TWRP recovery, but now I can't seem to get Viper LTE to load right, it keeps the damn stock ROM. I've tried ROM Manager, and now trying GooManager.
Okay, so I was able to not get the Venom LTE like I thought I wanted, so instead I have Cyanogen 10.1, but the problem is, now I either need to...
A: Get the phone into DIAG mode (AKA ##3424)
B: Program settings for the Cricket network
C: Find a Cricket-specific distro of Cyanogenmod.
So random question time: Does the ROM have to be 100% the device I'm trying to alter? I.e. I cannot use an Incredible 2 ROM on an Incredible 4G LTE?
the1corrupted said:
Okay, so I was able to not get the Venom LTE like I thought I wanted, so instead I have Cyanogen 10.1, but the problem is, now I either need to...
A: Get the phone into DIAG mode (AKA ##3424)
B: Program settings for the Cricket network
C: Find a Cricket-specific distro of Cyanogenmod.
So random question time: Does the ROM have to be 100% the device I'm trying to alter? I.e. I cannot use an Incredible 2 ROM on an Incredible 4G LTE?
Click to expand...
Click to collapse
You need stock to flash than flash the romantic you want.
the1corrupted said:
Okay, so I was able to not get the Venom LTE like I thought I wanted, so instead I have Cyanogen 10.1, but the problem is, now I either need to...
A: Get the phone into DIAG mode (AKA ##3424)
B: Program settings for the Cricket network
C: Find a Cricket-specific distro of Cyanogenmod.
So random question time: Does the ROM have to be 100% the device I'm trying to alter? I.e. I cannot use an Incredible 2 ROM on an Incredible 4G LTE?
Click to expand...
Click to collapse
Do not use another device's ROM on this phone!
A) Does *#*#4636#*#* not come up? (EDIT: Fixed typo)
B) Should already be included in CM
C) No such thing
fifiknw87 said:
You need stock to flash than flash the romantic you want.
Click to expand...
Click to collapse
This makes no sense.
You can't do ##3424# in cm10.1
You need a stock Samsung s4 rom
fifiknw87 said:
You can't do ##3424# in cm10.1
You need a stock Samsung s4 rom
Click to expand...
Click to collapse
1) You're clearly artificially inflating your post count so you can post in the dev section (which goes to show that you don't understand the purpose of the dev section)
2) You're wrong.
mdmower said:
Do not use another device's ROM on this phone!
A) Does *#*#3646#*#* not come up? You could try the 5/21 nightly and see if it comes up there.
B) Should already be included in CM
C) No such thing
This makes no sense.
Click to expand...
Click to collapse
Right now, *#*#3646#*#* gets me nothing, and my download from goo.im has been throttled to 4.8 Kbps... I must have offended them. Anyway, I'll give the nightly a try, unless you know of other codes that gets into DIAG mode? Maybe under the developer tools?
the1corrupted said:
Right now, *#*#3646#*#* gets me nothing, and my download from goo.im has been throttled to 4.8 Kbps... I must have offended them. Anyway, I'll give the nightly a try, unless you know of other codes that gets into DIAG mode? Maybe under the developer tools?
Click to expand...
Click to collapse
This app in the Play marketplace seems to work: Secret Phone Settings
Edit: So does this one: Hidden Menus
mdmower said:
This app in the Play marketplace seems to work: Secret Phone Settings
Edit: So does this one: Hidden Menus
Click to expand...
Click to collapse
I don't see an option for DM Command Service, which is what I really need. I need to program my phone with the QPST software like I can with the stock ROM.
Of course, I've already flashed the stock ROM, but when it's obliterated for the NEW ROM, my phone dumps the CDMA settings. Also, where might those be stored? If I do a "dirty flash" to CM10.1, maybe I can keep where I programmed my Mobile Directory Number and all that info?
Also, I've already tried *#*#3424#*#*, *#*#PROGRAM#*#*, *#*#DATA#*#* and nothing seems to go through to get the DM Command Service.
the1corrupted said:
I don't see an option for DM Command Service, which is what I really need. I need to program my phone with the QPST software like I can with the stock ROM.
Of course, I've already flashed the stock ROM, but when it's obliterated for the NEW ROM, my phone dumps the CDMA settings. Also, where might those be stored? If I do a "dirty flash" to CM10.1, maybe I can keep where I programmed my Mobile Directory Number and all that info?
Also, I've already tried *#*#3424#*#*, *#*#PROGRAM#*#*, *#*#DATA#*#* and nothing seems to go through to get the DM Command Service.
Click to expand...
Click to collapse
This seems unnecessary. Have you tried the following in cm-10.1? In build.prop change these lines:
Code:
# Carrier definitions
ro.cdma.home.operator.alpha=Verizon
gsm.sim.operator.alpha=Verizon
gsm.operator.alpha=Verizon
ro.cdma.home.operator.numeric=310012
gsm.sim.operator.numeric=310012
gsm.operator.numeric=310012
# Access to Verizon/HTC apps in Play store
ro.com.google.clientidbase=android-htc
ro.com.google.clientidbase.yt=android-verizon
ro.com.google.clientidbase.am=android-verizon
ro.com.google.clientidbase.gmm=android-htc
ro.com.google.clientidbase.ms=android-verizon
to this:
Code:
# Carrier definitions
ro.cdma.home.operator.alpha=Cricket
gsm.sim.operator.alpha=Cricket
gsm.operator.alpha=Cricket
ro.cdma.home.operator.numeric=310016
gsm.sim.operator.numeric=310016
gsm.operator.numeric=310016
mdmower said:
This seems unnecessary. Have you tried the following in cm-10.1? In build.prop change these lines:
Code:
# Carrier definitions
ro.cdma.home.operator.alpha=Verizon
gsm.sim.operator.alpha=Verizon
gsm.operator.alpha=Verizon
ro.cdma.home.operator.numeric=310012
gsm.sim.operator.numeric=310012
gsm.operator.numeric=310012
# Access to Verizon/HTC apps in Play store
ro.com.google.clientidbase=android-htc
ro.com.google.clientidbase.yt=android-verizon
ro.com.google.clientidbase.am=android-verizon
ro.com.google.clientidbase.gmm=android-htc
ro.com.google.clientidbase.ms=android-verizon
to this:
Code:
# Carrier definitions
ro.cdma.home.operator.alpha=Cricket
gsm.sim.operator.alpha=Cricket
gsm.operator.alpha=Cricket
ro.cdma.home.operator.numeric=310016
gsm.sim.operator.numeric=310016
gsm.operator.numeric=310016
Click to expand...
Click to collapse
So where's my MDN stored? Or is it all inferred from the APN? I don't need to load a PRL?
Keeps coming back with SIM Card Added, reboot to access network. Cricket doesn't use GSM...
Doesn't work. Need to load a PRL onto the phone. When I dial *611, it gives me Verizon Wireless.
the1corrupted said:
So where's my MDN stored? Or is it all inferred from the APN? I don't need to load a PRL?
Keeps coming back with SIM Card Added, reboot to access network. Cricket doesn't use GSM...
Doesn't work. Need to load a PRL onto the phone. When I dial *611, it gives me Verizon Wireless.
Click to expand...
Click to collapse
If you had read the first post of CM, you'd realize that you're just supposed to hit back when "SIM Card Added" comes up. I have successfully used QPST on this phone. See post 5 of this thread.
I take it Cricket is a sim-less CDMA carrier? If this is the case, then build.prop probably isn't sufficient. This is then outside of my realm of knowledge.
I just flashed cm-10.1.1-mdm02 onto my phone and I am having the "can't send MMS" issue. I would love to follow the fix supplied in the CyanogenMod 10.1 Official Releases thread, but I do not have the "CDMA subscription" or anything that even says "LTE" in the "preferred network mode. See Attachements Below.
Is this something that has been seen?
... And yes, I went a little overoard with my use of quotes
evolwun said:
I just flashed cm-10.1.1-mdm02 onto my phone and I am having the "can't send MMS" issue. I would love to follow the fix supplied in the CyanogenMod 10.1 Official Releases thread, but I do not have the "CDMA subscription" or anything that even says "LTE" in the "preferred network mode. See Attachements Below.
Is this something that has been seen?
... And yes, I went a little overoard with my use of quotes
Click to expand...
Click to collapse
That does not look like mdm02 (or any of my releases actually). If you came from another cm-based ROM, you may need to wipe /system before flashing. It should look like the attached picture.
mdmower said:
That does not look like mdm02 (or any of my releases actually). If you came from another cm-based ROM, you may need to wipe /system before flashing. It should look like the attached picture.
Click to expand...
Click to collapse
Nope, I have ONLY been using your CM roms since you came out with them. I have jumped around releases quite a bit though.
here is a screenshot of the build info
evolwun said:
here is a screenshot of the build info
Click to expand...
Click to collapse
kernel 3.0.71 tells me you haven't updated the kernel since the end of March. Extract boot.img from the cm zip and flash it:
Code:
fastboot flash boot boot.img
If you're running any modifications to cyanogenmod, they can also mess with the displayed settings. If you have any applications installed that supposedly give you more network options, uninstall them.
mdmower said:
kernel 3.0.71 tells me you haven't updated the kernel since the end of March. Extract boot.img from the cm zip and flash it:
Code:
fastboot flash boot boot.img
If you're running any modifications to cyanogenmod, they can also mess with the displayed settings. If you have any applications installed that supposedly give you more network options, uninstall them.
Click to expand...
Click to collapse
I just downloaded the mdm03 rom and flashed it as well as the boot.img from that .zip... no change. Am I looking a full wipe on this one?
BTW, thanks for the help on this.
evolwun said:
I just downloaded the mdm03 rom and flashed it as well as the boot.img from that .zip... no change. Am I looking a full wipe on this one?
BTW, thanks for the help on this.
Click to expand...
Click to collapse
Try this: in recovery...
make a full backup
wipe only /system
install build mdm03
install gapps
mdmower said:
Try this: in recovery...
make a full backup
wipe only /system
install build mdm03
install gapps
Click to expand...
Click to collapse
Still nothing, I thought that sounded like a great suggestion.
evolwun said:
Still nothing, I thought that sounded like a great suggestion.
Click to expand...
Click to collapse
Since you have a full backup, the next check would be to wipe /data, /cache, and /system, then install CM and see if the menu options appear like in my screenshot.
mdmower said:
Since you have a full backup, the next check would be to wipe /data, /cache, and /system, then install CM and see if the menu options appear like in my screenshot.
Click to expand...
Click to collapse
Will do, I'll do it tomorrow during the day and post up the results.
are you s-on with a locked bootloader?
I did a full wipe and everything is working fine. I love the fact that I can restore app data from titanium backup. I need to be more careful about keeping my boot.img up to date.
Messaging no worky MD04
evolwun said:
I did a full wipe and everything is working fine. I love the fact that I can restore app data from titanium backup. I need to be more careful about keeping my boot.img up to date.
Click to expand...
Click to collapse
I cannot send SMS or MMS messages...
Following instructions in this thread I did a TWRP Recovery/factory reset, flashed and reinstalled md04, it was working for awhile.
Proceeded to install my apps, somewhere along the way SMS died.
Also I now see as one other in this thread; under Settings/More/Mobile Networks - Preferred Network mode is LTE / WCDMA, if that is selected there are no options displayed that include "LTE"
LeonMBarnes said:
I cannot send SMS or MMS messages...
Following instructions in this thread I did a TWRP Recovery/factory reset, flashed and reinstalled md04, it was working for awhile.
Proceeded to install my apps, somewhere along the way SMS died.
Also I now see as one other in this thread; under Settings/More/Mobile Networks - Preferred Network mode is LTE / WCDMA, if that is selected there are no options displayed that include "LTE"
Click to expand...
Click to collapse
Can you connect to the network? If so, is your CDMA subscription set to RUIM/SIM?
--
also check Radio Information.
1. Go to dialer and enter: *#*#4636#*#*
2. Phone Information
3. Let preferred network type:
4. LTE/CDMA (PRL) (if not set to this, set it to this)
vazersecurity said:
Can you connect to the network? If so, is your CDMA subscription set to RUIM/SIM?
--
also check Radio Information.
1. Go to dialer and enter: *#*#4636#*#*
2. Phone Information
3. Let preferred network type:
4. LTE/CDMA (PRL) (if not set to this, set it to this)
Click to expand...
Click to collapse
I think this is solved.
Trying different things, found that when the system has a fresh MD04, go to Settings/More/Mobile Networks/Network Mode - changed to "LTE/CDMA/EvDo". Since then it is behaving and SMS is working, Also I checked the Radio info per instructions above, it shows "LTE/CDMA auto (PRL)".
All is good for now. :fingers-crossed:
Thanks again.
As the title says guys,
I was about to root my Sprint Note III, but I received the update and now the Note III is running Android 4.4.4.
I don't want to do something and the get stuck with it.
Has it been done since the update?
Chainfire autoroot still works
ssuraj83 said:
As the title says guys,
I was about to root my Sprint Note III, but I received the update and now the Note III is running Android 4.4.4.
I don't want to do something and the get stuck with it.
Has it been done since the update?
Click to expand...
Click to collapse
You can always just use odin to install twrp than use twrp to install supersu
Thank for the reply guys.
I read also this still trips Knox.
ssuraj83 said:
Thank for the reply guys.
I read also this still trips Knox.
Click to expand...
Click to collapse
For sure. Knox can be reset and worked around at a later date so its really not a big deal but at the moment it will indicate 0x1 on the stock recovery indicating you have rooted your device.
What I want to know is how to get the Native hotspot working. My Galaxy tools APK is not doing the trick and the APN settings are completely different. anyone have this issue???
chuxmix said:
For sure. Knox can be reset and worked around at a later date so its really not a big deal but at the moment it will indicate 0x1 on the stock recovery indicating you have rooted your device.
What I want to know is how to get the Native hotspot working. My Galaxy tools APK is not doing the trick and the APN settings are completely different. anyone have this issue???
Click to expand...
Click to collapse
Hmm i tried thevgalaxy tools and it worked for me
chuxmix said:
For sure. Knox can be reset and worked around at a later date so its really not a big deal but at the moment it will indicate 0x1 on the stock recovery indicating you have rooted your device.
What I want to know is how to get the Native hotspot working. My Galaxy tools APK is not doing the trick and the APN settings are completely different. anyone have this issue???
Click to expand...
Click to collapse
Can we see a screenshot of your apn's? They can be opened editable without msl if you change sales_code in galaxy tools to XAS and reboot phone.
Also a copy of the file after a ##scrtn#
Enter that in dialer and wait till phone reboots and finishes, then click enable native hotspot only once and post telephony.db.bk for me to see. (it will be in root of internal sdcard)
---------- Post added at 01:15 PM ---------- Previous post was at 01:03 PM ----------
@chuxmix
Go see last couple posts in that thread, what helped the last user might help you too.
Well the apns look completely different and the ##scrtn# only forces me to reboot then reactivate then reboot all over again.
chuxmix said:
Well the apns look completely different and the ##scrtn# only forces me to reboot then reactivate then reboot all over again.
Click to expand...
Click to collapse
Everyones can look like that. Change sales_code like I said, reboot and they WILL open editable, and you will then be able to select/edit them. Or try the forced lte like I suggested in the other thread (and it worked for that user)
And the point of the scrtn was for you to grab that file. It resets your apns to default (deletes all but ota ones) then reboots and pulls new apns from the network.
Already XAS opened this but im not sure how to force the lte or what to edit it to??? ÷Edit. Woops i got it now!!! it was able to reset and i opened up the selected right after i clicked the Enable hotspot button and it had the ,dun already in place. Thanks Idone
chuxmix said:
Already XAS opened this but im not sure how to force the lte or what to edit it to???
Click to expand...
Click to collapse
You don't need to edit them, you thought your apns were different but they are not.
click enable hotspot in galaxy tools, wait 10 seconds or so, go into your apns and select ehrpd then select lte.
Now go test turning on hotspot.
The force lte setting is accessible through IOTHiddenmenu. I was just saying to do that if you go into apns and have none of them selected(because tethering requires one of the 2 internet apns to be active/selected) and sometimes the phone is weird and no apn is selected.
Thanks to a few memebers here for posting back. I went ahead and used CF AUTO ROOT to root the newest firmware. Below is screen shot in Odin mode.
Some issues to share;
First, if i want to use my home wifi, I have to reboot my phone for it to work. Can anyone confirm this?
Second, thanks to the galaxy tool, I now have hotspot again.
My issue here, it only allows one device to connect at a time. For the use of another device, I have to turn off one.
Anyone having these issues?
ssuraj83 said:
Some issues to share;
First, if i want to use my home wifi, I have to reboot my phone for it to work. Can anyone confirm this?
Second, thanks to the galaxy tool, I now have hotspot again.
My issue here, it only allows one device to connect at a time. For the use of another device, I have to turn off one.
Anyone having these issues?
Click to expand...
Click to collapse
Hi,
First if you enjoy GalaxyTools consider buying me a drink.
Second in hotspot go to configure>scroll to bottom and select "show advanced options">scroll to bottom again> max user can be up to 8
If you have more devices I can give you command to send from terminal to try and increase it.. I've not enough wifi devices to test more than 8 sorry.
Good luck!
****edit****
Yes just tested I can increase max users, will add this to GalaxyTools later today and post update.
***edit***
GalaxyTools updated, add as many hotspot users as you like!
http://forum.xda-developers.com/not.../app-one-click-hotspot-enabler-menus-t2816159
idone said:
Hi,
First if you enjoy GalaxyTools consider buying me a drink.
Second in hotspot go to configure>scroll to bottom and select "show advanced options">scroll to bottom again> max user can be up to 8
If you have more devices I can give you command to send from terminal to try and increase it.. I've not enough wifi devices to test more than 8 sorry.
Good luck!
****edit****
Yes just tested I can increase max users, will add this to GalaxyTools later today and post update.
***edit***
GalaxyTools updated, add as many hotspot users as you like!
http://forum.xda-developers.com/not.../app-one-click-hotspot-enabler-menus-t2816159
Click to expand...
Click to collapse
Thank you for replying.
I figured it out once I started to mess with it.
Can someone chime in and tell me what the 4 means?
Knox warranty void: 0x1 (4)
lolz @ attached pic
Flash counter ?
ssuraj83 said:
Thanks to a few memebers here for posting back. I went ahead and used CF AUTO ROOT to root the newest firmware. Below is screen shot in Odin mode.
Some issues to share;
First, if i want to use my home wifi, I have to reboot my phone for it to work. Can anyone confirm this?
Second, thanks to the galaxy tool, I now have hotspot again.
My issue here, it only allows one device to connect at a time. For the use of another device, I have to turn off one.
Anyone having these issues?
Click to expand...
Click to collapse
Check out my post 4.4.4 ( Download Mode ) below, that I made right after I upgraded to 4.4.4, now check out the post above. Is that number (4) a flash counter ?
I have since gone back to 4.4.2, there's to many problems with 4.4.4. So is anyone rooted with 4.4.4 that can check this out ?
Does it reset if you unroot the device and go back to official stock ?
I was reading your post aswell.
I only flashed/rooted this phone yesterday using odin3 v3.07 and noticed you can't uncheck F.reset time. Now, my binary and sytem says custom.
See below screen shot.
I am not running a custom recovery.
If i wanted to go back to nc5, can I use odin to do that?
Thanks.
ssuraj83 said:
I was reading your post aswell.
I only flashed/rooted this phone yesterday using odin3 v3.07 and noticed you can't uncheck F.reset time. Now, my binary and sytem says custom.
See below screen shot.
I am not running a custom recovery.
If i wanted to go back to nc5, can I use odin to do that?
Thanks.
Click to expand...
Click to collapse
Odin can put you back to nc5.
And if you can't uncheck it on the menu do it in Odin3.ini
[APOption]
FResetTime=0
I will try it.
Thanks idone.
Hi guys,
I flashed Resurrection Remix and it wouldn't start on the first boot. Restored nandroid and got stuck in bootloop, so I went back to stock using the TOT method (ZV4 then let OTA updates get me to ZVC), and I noticed that on my lock screen, it said LG instead of Sprint, and I noticed I had no data. So I tried the 3 dialer codes: ##UPDATE#, ##SCRTN#, and ##RTN#. After this I can now get 3G and it says Sprint on my lockscreen, but no 4g, In settings/mobile networks/network mode LTE/CDMA is selected. In settings/about phone/network, the mobile network type is either EvDo-rev.A or eHRPD(it goes back and forth). I'm wondering if its an APN setting but I can't find anything on this. Any ideas on how I can get 4G back? Thanks for any ideas.
Did you try a profile update? try running 2 of them, then a PRL update, than another profile update. It's pretty picky. [I mean though the System Update tab]
Warboy said:
Did you try a profile update? try running 2 of them, then a PRL update, than another profile update. It's pretty picky. [I mean though the System Update tab]
Click to expand...
Click to collapse
Tried your suggestion but no change, The first profile update took about a minute, and the others went really quick. Still no LTE.
curtvan said:
Tried your suggestion but no change, The first profile update took about a minute, and the others went really quick. Still no LTE.
Click to expand...
Click to collapse
Hmm, Try a reboot and a PRL update than a Profile Update?
curtvan said:
Hi guys,
I flashed Resurrection Remix and it wouldn't start on the first boot. Restored nandroid and got stuck in bootloop, so I went back to stock using the TOT method (ZV4 then let OTA updates get me to ZVC), and I noticed that on my lock screen, it said LG instead of Sprint, and I noticed I had no data. So I tried the 3 dialer codes: ##UPDATE#, ##SCRTN#, and ##RTN#. After this I can now get 3G and it says Sprint on my lockscreen, but no 4g, In settings/mobile networks/network mode LTE/CDMA is selected. In settings/about phone/network, the mobile network type is either EvDo-rev.A or eHRPD(it goes back and forth). I'm wondering if its an APN setting but I can't find anything on this. Any ideas on how I can get 4G back? Thanks for any ideas.
Click to expand...
Click to collapse
what copy of Resurrection Remix you flash?
Warboy said:
Hmm, Try a reboot and a PRL update than a Profile Update?
Click to expand...
Click to collapse
Just tried that, no change.
imerza82 said:
what copy of Resurrection Remix you flash?
Click to expand...
Click to collapse
It was Resurrection Remix 6.0.1 Marshmallow, but it was about a week ago so I'm not sure what version it was, I see it was updated 1/30.
I notice that it has a refresh animation by the signal meter now too. http://i.imgur.com/NqnUNPt.png Thats what made me think it was an APN setting. It does the refresh for about 30 seconds before it can find a signal.
[/COLOR]
curtvan said:
I notice that it has a refresh animation by the signal meter now too. http://i.imgur.com/NqnUNPt.png Thats what made me think it was an APN setting. It does the refresh for about 30 seconds before it can find a signal.
Click to expand...
Click to collapse
Better tot flash again/flash the correct stock/root/recovery/then flash http://www.oadam11.com/LG_G3/ls990/RR/ResurrectionRemix-M-v5.6.2-20160130-ls990.zip
With update gapps. http://download.dirtyunicorns.com/f...s/BaNkS_Dynamic_GApps_6.x.x_1-26-16_15:04.zip
it will be solved
imerza82 said:
[/COLOR]
Better tot flash again/flash the correct stock/root/recovery/then flash http://www.oadam11.com/LG_G3/ls990/RR/ResurrectionRemix-M-v5.6.2-20160130-ls990.zip
With update gapps. http://download.dirtyunicorns.com/f...s/BaNkS_Dynamic_GApps_6.x.x_1-26-16_15:04.zip
it will be solved
Click to expand...
Click to collapse
Maybe I will try that this weekend. I'm trying to get it back to stock so I can sell it.
imerza82 said:
[/COLOR]
Better tot flash again/flash the correct stock/root/recovery/then flash http://www.oadam11.com/LG_G3/ls990/RR/ResurrectionRemix-M-v5.6.2-20160130-ls990.zip
With update gapps. http://download.dirtyunicorns.com/f...s/BaNkS_Dynamic_GApps_6.x.x_1-26-16_15:04.zip
it will be solved
Click to expand...
Click to collapse
Still no luck. Everything working good with Resurrection Remix except data is 3G and not LTE. I also tried flashing some different modems but that didn't change anything. I am thinking there is a partition that doesn't get wiped out during a TOT flash and something is wrong in that area. I am going to try to mess with APN settings when I get time.
curtvan said:
Still no luck. Everything working good with Resurrection Remix except data is 3G and not LTE. I also tried flashing some different modems but that didn't change anything. I am thinking there is a partition that doesn't get wiped out during a TOT flash and something is wrong in that area. I am going to try to mess with APN settings when I get time.
Click to expand...
Click to collapse
This may sound like a stupid question but, do you have a SIM card in?
cipollone88 said:
This may sound like a stupid question but, do you have a SIM card in?
Click to expand...
Click to collapse
Yes SIM card is in. I went back to stock everything again and the 4G problem remains.
curtvan said:
Yes SIM card is in. I went back to stock everything again and the 4G problem remains.
Click to expand...
Click to collapse
Using the ##RTN# dailer code and entering my MSL/SPC code has always got back to a fully functioning stock bloated device when needed. Best of luck to ya!