hello everyone
I would like to permanently hard brick my phone wt19i...... I tried everything from flashing other phone's rom, kernel and recovery. Tried using rom manager too, but nothing worked. As soon as I flash stock gb or stock ics, the phone comes back to life again.
Please if someone could suggest a working method so that even the service centre guys won't be able to fix.
Why would you want to do that
Easiest way would be to physically mess up the chip, shorting something or so.
Sent from my SM-N9005 using Tapatalk
How to short something in hardware.....all I found by searching was flashing improper things.....but each method failed....as soon as to confirm hard brick I tried to flash stock rom it flashed normally and booted too
anikanu said:
How to short something in hardware.....all I found by searching was flashing improper things.....but each method failed....as soon as to confirm hard brick I tried to flash stock rom it flashed normally and booted too
Click to expand...
Click to collapse
have Xperia Mini St15i rooted unlocked bootloader. Running on CM 11.0 very well
but I recent update to latest build 24072015 and I can't boot my phone; after I tried to restore my old backup,tried to install old Rom which is( I installed in past successful)l and tried flash Xperia mini stock rom ftf (various version) but phone doesn't start can say hard brick.
I can install all of them successfully but phone does not start. always displays error of "unfortunately the process com.android.phone has stopped and phone restart on boot logo again and again.
update......
I recently flash BeanStalk-4.4006-20131128-smultron and after many tries I success to start phone but I noticed that in apps only 50 MB memory is free. I didn't have installed any app. in past I have there is about 370 MB free.(xperia mini has 420 mb data partition)
I have try to erase system,data with fastboot but nothing happens
I attached text file of fastboot commands.
I tried to flash sony origional firmware too but it only restarts again and again .
I have tried to erase system and userdata with fastboot but i see that it encountered bad block in erase data, I can't understand why data partition can't be formated ? text document attached
I think my data partition is full. after reboot in recovery there is an error of " no space left in device " phone does not start normally. I can boot in recovery but still can not use phone .
running on CM 11 and this problem is start on flashing cm-11-20150723-UNOFFICIAL-LegacyXperia-smultron. after that my phone doesn't start.
Related
Hello guys,
as a last resort I turn to you for help. Have been searching for the answer for the last 2 days. I am running CWM-based Recovery v.6.0.1.1 and have a rooted x10 together with an unlocked bootloader. I flashed the recovery without any problems and installed miui v4 but an older file which was very unstable (without any problems). Then I decided to install the newer version so i downloaded it, placed it on my sdcard and in the same recovery flashed rom. Unfortunately I had my usb cable plugged in all the time (during installation). Installation got stuck in the middle and nothing could be done so i removed the battery and started the phone again (this time without the usb cable). When I tried to reinstall that rom again it gave me status 7 error installation aborted, assert failed:getprop,error in sdcard and things like that. So I tried the ROM which had already worked on my phone but received exactly the same message. What is more usb storage mounting in the recovery doesnt work anymore (but it already worked!). Now the problem is that I don't have any system installed and when i try to flash the recovery again, flashtool does not recognize my phone (so does windows) and so it leads me nowhere. I think this is definitely problem with the recovery, after the failed attempt to install rom when i had to remove the battery it does not behave normally. Is there any way that I can maybe install another recovery from .zip - i do not even know whether it will install or just sends me another error. Any help would be greatly appreciated
SqU33z3R said:
Hello guys,
as a last resort I turn to you for help. Have been searching for the answer for the last 2 days. I am running CWM-based Recovery v.6.0.1.1 and have a rooted x10 together with an unlocked bootloader. I flashed the recovery without any problems and installed miui v4 but an older file which was very unstable (without any problems). Then I decided to install the newer version so i downloaded it, placed it on my sdcard and in the same recovery flashed rom. Unfortunately I had my usb cable plugged in all the time (during installation). Installation got stuck in the middle and nothing could be done so i removed the battery and started the phone again (this time without the usb cable). When I tried to reinstall that rom again it gave me status 7 error installation aborted, assert failed:getprop,error in sdcard and things like that. So I tried the ROM which had already worked on my phone but received exactly the same message. What is more usb storage mounting in the recovery doesnt work anymore (but it already worked!). Now the problem is that I don't have any system installed and when i try to flash the recovery again, flashtool does not recognize my phone (so does windows) and so it leads me nowhere. I think this is definitely problem with the recovery, after the failed attempt to install rom when i had to remove the battery it does not behave normally. Is there any way that I can maybe install another recovery from .zip - i do not even know whether it will install or just sends me another error. Any help would be greatly appreciated
Click to expand...
Click to collapse
Flash tool recognize your phone? if yes flash any stock firmware and start over
quintas84 said:
Flash tool recognize your phone? if yes flash any stock firmware and start over
Click to expand...
Click to collapse
When I want to flash .tft file and i go to flash mode it does not recognize my phone in windows even though I have installed all the necessary drivers. It starts to flash but then says flashing aborted (this did not happen before, i could flash without any problems). Another problem is that i do not have any rom installed right now so i cannot even switch debugging on and if i remember right, i left debugging off in my previous rom.
Use Sony Update Service. Download from Sony site and install on PC. Follow the instruction, and this will reflash Stock Rom and Kernel (GB 2.3.3). Then, with latest Flashtool, first Root phone again, then flash whatever you want (custom kernels, roms..). You don't need to unlock bootloader again. It remains unlocked.
Sent from my X10i using xda premium
Dzufa said:
Use Sony Update Service. Download from Sony site and install on PC. Follow the instruction, and this will reflash Stock Rom and Kernel (GB 2.3.3). Then, with latest Flashtool, first Root phone again, then flash whatever you want (custom kernels, roms..). You don't need to unlock bootloader again. It remains unlocked.
Sent from my X10i using xda premium
Click to expand...
Click to collapse
Omg - I found solution to my problem - I just changed usb port and it started to flash even using flashtool. Still, many thanks since it helped me find solution
Hi Everyone! just a rookie here in need of a bit of advice.
I'm a Galaxy S II I9100 owner and have my phone rooted and all setup with custom roms and been comfortable with flashing for some time now. My ROM of choice recently was Vanilla Rootbox and have to say the ROM has been fantastic with very few bugs to report. Last night i recieved the OTA update via Goo Manager for Vanilla Rootbox 3.4. I downloaded the full update over wifi and flashed with all wipes no worries. Next step was to flash the latest GAPPS and i figured there would be nothing wrong with flashing the GAPPS zip i had on my sd card that i had downloaded the last time i was notified of a GAPPS update via Goo manager as well. After flashing, wiping everything and rebooting again. My phone then booted up to a series of dialog boxes indicating that many google processes had stopped functioning. apps.google.com etc etc. A similar error has been reported in the Vanilla Rootbox thread by another user but i wasnt able to report this bug their either because my post count is too low to post in a development forum. So after seeing this error i rebooted into recovery to flash my last backup but CWM recovery came back with an error messaging stating it couldnt mount either ext or int sdcard. i did a factory reset which made no difference to the problem whatsoever. I then downloaded ODIN and the latest stock ICS Rom and flashed it via ODIN with no reported errors. My phone now boots through the optus boot animation and is stuck at the Galaxy S 2 screen with the flashing red and yellow animation over the S. If i turn off the phone with the power button, the phone turns off and immediately starts again and gets stuck at the flashing s screen. I've taken the battery sim and ext sd card out and put it all back in only for the problem to persist.
If anyone could help me there's a donation and my thanks in it!
Much appreciated
Nick
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
gastonw said:
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
Click to expand...
Click to collapse
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
darkstar117 said:
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
Click to expand...
Click to collapse
wow wow, leave pit files alone for now, they are nasty.
What stock ROM did you flash? 4.0.4 or 4.0.3?
You can factory reset via recovery mode.
Try installing kies anyway, it can't never hurt. Just make sure all applications are closed before you re-flash.
here's jb leak, might help:
http://www.sammobile.com/2012/11/15/i9100xxlsj-%E2%80%93-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
darkstar117 said:
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
Click to expand...
Click to collapse
Tell me your:
Model
Firmware
Country
Carrier
Always mention this
try flashing jb leak (ROM, modem & kernel package).
While I did find a similar posts, they were for different devices. I also tryed to search o different sites for similar problems to no avial.
What Happened: After backing up system data and app data then removing Foxhound ROM with factory reset, and installing UltimaROM i came to find that the modem did not install correctly result in no connection to my cell network. I booted into TWRP recovery to try and do a re-install of the ROM only to find that TWRP was restarting itself every 3 seconds or so. I attempted to restart the device which i found to result in a TWRP bootloop that i cannot get out of, it constantly is booting into recovery mode and i cannot get it restart the OS.
What I've tried: Since i can get into download mode i decided to attempt to re-install TWRP using Samsung Galaxy S3 Toolkit but since i do not have USB debugging on i cannot do that. I'm mainly looking for a fix before i go and claim it on the warranty saying update went bad or something. If people need more information I will try to provide it as best i can.
Summery if i confused people is that TWRP is in a bootloop, i am unable to get to the OS, but i still have download mode available.
I fixed it but not how I would have liked to. I ended up losing all data due to flashing stock ROM using ODIN. I would still much appreciate a alternative method that does not involve loss of data though just for future reference, that is if anyone knows a alternative method.
Sent from my GT-I9300 using xda app-developers app
could've tried reflashing TWRP or any other recovery through odin
I have an LG Optimus Q (LGL55c) with twrp loop. I was trying to go back to stock rom, instead I deleted all the system files in twrp when it was working...Then I rebooted back into recovery and get the loop. Does this mean I completely bricked my phone? I tried using adb, adb shell doesn't work. It does find the device. Even tried the LG update with no sucess Any ideas or suggestions?
I just read the forum title, I thought this was for the Optimus Q not the Samsung S3. Sorry mods
Temasek unofficial cm12 5.02
I was running this rom when my power button shorted and I got it replaced but then I tried to do a complete wipe and clean flash but since then it has been twrp bootlooping, tried to flash the latest recovery through Odin but still doesn't work also tried stock firmware flash but says binary not available.
This is my secondary device and I've not been in touch with Odin for a while. Any help will be appreciated.
Thanks
Download latest firnware from sammobile.com and flash it with Odin, as described on sammobile: does Odin finish with '1 succeeded'?
I'm in a very similar situation, but with my Samsung Galaxy Note 2 (N7105). It's rooted, and I am, or was using TWRP 2.7.0.2. ROM is CyanogenMod 12, 5.0.2 Lollipop.
I did a factory reset from INSIDE Android, and chose to wipe internal memory. Phone did the reset and wipe, rebooted into TWRP instead of Android, and now I have TWRP boot loop.
I posted more about it here: http://forum.xda-developers.com/showpost.php?p=60247503&postcount=3671
I have the Problem toooo!
What must i do Now!
with my S3 is the same!!!
For posterity:
With an old (2014?) version of TWRP and a custom ROM, I tried reverting to factory settings. That caused the phone to reboot TWRP, and the screen would flash every couple of seconds. I flashed a stock recovery image I found on Google, and when it restarted again, the wipe was completed successfully. My intention was to wipe all user data anyways so I can't say if this method might save it.
I assume my NAND rw is corrupted and would like to confirm that and get recommendations what to flash now.
Here's what happened:
Been running Resurrection Lollipop for a while successfully until Play Services started force closing loads. Upgraded to CM13 hoping it would resolve it, it didn't. Ended up with Cyanogen Recovery that came with CM13, which didn't allow me to flash any other rom ('installation failed'). Tried flashing CWM Touch Recovery 5.8x with Odin, which got stuck at Open NAND, had to close Odin eventually and the phone is now giving the Samsung recovery error (Firmware error encountered...). Kies won't recognize it despite driver reinstall, Kies' recovery function doesn't list it. When trying to flash the CWM Recovery i'm getting a NAND write error. I found an old thread on this issue on GB/ICS, but not sure if their steps apply to LP/MM, let alone which files to use now.
Thank you all in advance for being helpful!
@tiethilo
Flash stock 4.1.2 with Odin. If odin flash will be succesfull , phone should end in Samsung animation bootloop. If it haleens , take out battery , go to recovery , select wipe data/factory reset and viola. Your phone should be working.
So I recently tried to unroot my device with flashing official ROM on it. Apparently I used the wrong file because my phone got bricked. I tried using XiaoMiTool by Francesco but it didn't help. I spent a lot of time trying to fix it so ill post what worked for me. I downloaded a lot of ROMS but none of them worked for me there was either flash error or device mismatching and I couldn't find right flash official software anywhere. I downloaded another ADB fixing program which worked, I downloaded Szaki/XiaomiADB fastboot tools which worked perfectly. I simply connected my phone searched for my phone code name (tucana) downloaded ROM from there, wiped all data off and finally flashed OS on my device. I also have a question, are there any android software fixing programs for phone repair companies or something similar?
Have good day and stay healthy,
MX8MC8
id suggest to unbrick with mi flash tool.
I did that always when i was stuck on something, it ofcourse removes your data but saves the device so its still the profit probably... After succesfull rom installation you can flash again.
Also you do this in fastboot mode
When I was stuck in the same way the solution I found was to flash whatever rom then when the phone bootloops, go into recovery, and format data. Afterwards it will boot to startup screen and take forever to load up. Anyway that is my solution, before that I would have to flash stock recovery to boot for the first time then flash a custom recovery back.