(Rooted and UnRooted)You need to flash your stock recovery first if U have flashed custom recoveryBut how ??
1. First of all please plug your charger to phone and charge it fully 100%
2 Put your phone to Air plane mode and Unplug your charger
3. Turn off your phone and plug charger again wait till the battery is fully charged and shows 100%(wait around 2 mins) [ don't Unplug the charger ]
4. Turn it on and go to the dialer
5. Dial *#0228# (a page pop's up)
6. Unplug your charger and wait around 30 secs
7. Touch Quick Start then OK
8. Reboot and Turn off the Air plane mode
(Just rooted devices) Battery calibration :
Please download RootExplorer and install it then
Please Do the same as part 1 & 2 & 3
4. Launch RootExplorer go to : Root/data/system >
5. Find batterystats.bin and unplug your charger and wait for 30 secs then DELETE batterystats.bin
6. Reboot and Turn off the Air plane mode
Enjoy and Thanks for your Thanks
Is there any technical explanation about how is the battery would even better from this tutorial?
Mr.IDK said:
Is there any technical explanation about how is the battery would even better from this tutorial?
Click to expand...
Click to collapse
It s necessary when u change your ROM or update it .
the calibration of battery depends on ROM
You change the Rom You change the calibration !
adblocker said:
It s necessary when u change your ROM or update it .
the calibration of battery depends on ROM
You change the Rom You change the calibration !
Click to expand...
Click to collapse
Oh.... So this is the Calibration method?
Sorry bout that, you should indicate it at the first place though. I thought this is just a trick.
I will try because my go down faster thanks
Related
How am I supposed to do the battery trick when after my phone dies and I plug it in all that happens it either the phone starts up or it boots into CWM immediately. There is no battery image that lets me charge to 100% then turn it on and boot into CWM. I am on 2.2, 4.5 GingerBlur. I am unlocked.
Was following this guide:
Your battery life is often killed when flashing ROMs in CWM. For the best battery life, you must drain your device’s battery until it turns off. Plug the device into the AC adapter and let it charge till the image says 100% charged. Then turn it on and use the volume buttons to boot into CWM. Click Wipe Battery Stats under the advanced menu. Then you should charge to 100% and install the ROM. Battery life should be comparable to (if not better than) every other ROM.
Click to expand...
Click to collapse
live_free said:
How am I supposed to do the battery trick when after my phone dies and I plug it in all that happens it either the phone starts up or it boots into CWM immediately. There is no battery image that lets me charge to 100% then turn it on and boot into CWM. I am on 2.2, 4.5 GingerBlur. I am unlocked.
Was following this guide:
Click to expand...
Click to collapse
Just charge with the phone on to 100% and either reboot into cwm to wipe stats or delete the baterrystats.bin yourself through root explorer.
Hi i just installed bad bass battery and noticed that "Kernel" is using 29% of the battery..is that normal?i'm using LF2 stock ROM with siyah 1.1 kernel my battery went from 99% to 94% in 1h15 mn i only have wifi on, no syncing or naything else
It seems to be the kernel your problem,flash another kernel, first try to calibrate your battery ....METHOD 1-- 1
. Please download the phone completely.
2. Try to restart, if this were to happen, do it again to turn off for lack of battery.
3. Loaded the phone off preferably overnight or long.
4. Turn on the phone with the charger plugged in and then pull it off.
N. B. does not require the Root. -METHOD 2-- 1
. Download the phone completely.
2. Enter into Recovery Mode (if it is not possible for lack of battery, connect the phone to the charger).
3. Follow the path Advanced -> Wipe battery stats and confirm.
4. Go back and restart (i.e. , follow the path Go Back -> Reboot system now). 5. Leave charge the phone completely up to 100% (preferably overnight or long) and then let it drain completely until the off., without connecting it to your PC or to the charger, during this period. N. B. You must have Root * Clockworkmod recovery installed. METHOD 3-- 1. Charge your phone to 100% (with the phone turned on) preferably overnight or at least a long period. 2. Leave the phone connected to the charger and switch off the appliance. 3. Let it load still for 10-15 minutes (always without disconnecting it from the charger) in practice you have to see the written full charge or the % to 100 %. 4. Enter into Recovery Mode (always without disconnecting it from the charger) and follow the path Advanced -> Wipe battery stats and confirm. 5. Reboot (i.e. , follow the path Go Back -> Reboot system now). 6. Wait for the entire system is loaded, and then disconnect it from the charger. N. B. You must have Root * Clockworkmod recovery installed. METHOD 5-- 1
. Turn off your phone.
2. Fully charge your phone, preferably overnight or long.
3. When the battery is fully charged and marks the 100% disconnect your phone and remove the battery.
4. Wait for 90 seconds to be exact (it must really be precise, wait exactly 90 seconds.) 6. Put the battery and turn on your phone. N. B. are not required nor Root nor Clockworkmod recovery.
devid801 said:
It seems to be the kernel your problem,flash another kernel, first try to calibrate your battery ....METHOD 1-- 1
. Please download the phone completely.
2. Try to restart, if this were to happen, do it again to turn off for lack of battery.
3. Loaded the phone off preferably overnight or long.
4. Turn on the phone with the charger plugged in and then pull it off.
N. B. does not require the Root. -METHOD 2-- 1
. Download the phone completely.
2. Enter into Recovery Mode (if it is not possible for lack of battery, connect the phone to the charger).
3. Follow the path Advanced -> Wipe battery stats and confirm.
4. Go back and restart (i.e. , follow the path Go Back -> Reboot system now). 5. Leave charge the phone completely up to 100% (preferably overnight or long) and then let it drain completely until the off., without connecting it to your PC or to the charger, during this period. N. B. You must have Root * Clockworkmod recovery installed. METHOD 3-- 1. Charge your phone to 100% (with the phone turned on) preferably overnight or at least a long period. 2. Leave the phone connected to the charger and switch off the appliance. 3. Let it load still for 10-15 minutes (always without disconnecting it from the charger) in practice you have to see the written full charge or the % to 100 %. 4. Enter into Recovery Mode (always without disconnecting it from the charger) and follow the path Advanced -> Wipe battery stats and confirm. 5. Reboot (i.e. , follow the path Go Back -> Reboot system now). 6. Wait for the entire system is loaded, and then disconnect it from the charger. N. B. You must have Root * Clockworkmod recovery installed. METHOD 5-- 1
. Turn off your phone.
2. Fully charge your phone, preferably overnight or long.
3. When the battery is fully charged and marks the 100% disconnect your phone and remove the battery.
4. Wait for 90 seconds to be exact (it must really be precise, wait exactly 90 seconds.) 6. Put the battery and turn on your phone. N. B. are not required nor Root nor Clockworkmod recovery.
Click to expand...
Click to collapse
thnx i will try that..but i do always charge my phone overnight
Battery stats are wiped anyway when the phone is full, they are not used for calibration. (The battery got an internal chip for that)
Calibration is achieved by fully charging, fully discharging in one go and then fully charging again (A so-called battery cycle) as included in the above description.
However note that a full discharge causes a lot of strain to your battery; if you often completely drain your battery it will degrade very fast.
If you got a lot of apps which have data usage or a poor Wifi connection the drain might be normal since it requires the chipset to work far more than under optimal conditions.
ok back again the kernel is eating 37% of the battery as least thats according to bad ass battery stats..i(m on shiyah
I HAVE SAMSUNG GALAXY S3
GT:19300
STOCK ROM 4 . 1 .2
I HAVE hard bricked ( NO POWER -NO RECOVERY - NO DOWNLOAD )
HOW I CAN DEBRICKED IT ?
i WANT MY PHONE BACK
THANK YOU
Try a usb jig.
How did you brick it?
replay
i dont know
first time its reboot him self then he turn of and not back
i try to go to recovery download nothing
yoyo20132013 said:
i dont know
first time its reboot him self then he turn of and not back
i try to go to recovery download nothing
Click to expand...
Click to collapse
What % was the battery at when it rebooted? Also, have you had any dying battery symptoms (e.g. screen flickering, fast drain, sudden drops in battery etc).
Hello, by mistake I copy wrong aboot file to /dev/block/playform/msm_sdcc.1/by-name/aboot
It is possible to boot my phone or other way to copy proper file? What can I do?
Now I can't boot, can't charge, can't anything.
You didn't look very hard, did you?
Anyway: http://forum.xda-developers.com/g2-mini/general/guide-unbrick-bricked-wrong-aboot-img-t3128896
Vagelis1608 said:
You didn't look very hard, did you?
Anyway: http://forum.xda-developers.com/g2-mini/general/guide-unbrick-bricked-wrong-aboot-img-t3128896
Click to expand...
Click to collapse
It is possible to do it with charged battery?
I can see battery icon but my battery is charged and I can't get download mode so 3. and 4. not working.
How download mode looks like? Below image is download mode in LG G2 mini D620r ?
http://webtrickz.com/wp-content/uploads/2015/04/IMG_20150422_1322211.jpg
1) take out the battery
2) plug the phone in a PC via micro USB
3) while holding volume up, put in the battery
4) screen whill pop up asking you to hold volume up, relise it and press it agen till you get in download mode.
k4misiek said:
It is possible to do it with charged battery?
I can see battery icon but my battery is charged and I can't get download mode so 3. and 4. not working.
How download mode looks like? Below image is download mode in LG G2 mini D620r ?
http://webtrickz.com/wp-content/uploads/2015/04/IMG_20150422_1322211.jpg
1) take out the battery
2) plug the phone in a PC via micro USB
3) while holding volume up, put in the battery
4) screen whill pop up asking you to hold volume up, relise it and press it agen till you get in download mode.
Click to expand...
Click to collapse
I have read all articles about wrong aboot and there is a hope. But first I need uncharched my battery somehow .
I'll tell you for some days if it works or not.
k4misiek said:
I have read all articles about wrong aboot and there is a hope. But first I need uncharched my battery somehow .
I'll tell you for some days if it works or not.
Click to expand...
Click to collapse
I read somewhere that someone with the same issue connected the battery with a LED and a resistor to discharge it. I don't remember what he did, nor do I recommend it, if you don't know what you are doing.
I connect LED to battery. It looks like this: https://ibb.co/f9PxgF
Now I am waiting for fully uncharged. This connection is enought to 0% ?
Done. I repair my phone, thanks very much!
Here is video. Battery 0% works!
https://www.youtube.com/watch?v=dPH6woDexcM&t=45s
Hey all so I'm having trouble with the SM-G890A Galaxy S6 Active. One day the phone just kept going into a restart loop, so I took it into the T-mobile store to see what they could do to fix it as they are my current phone service provider. NOTE: The phone is originally from AT&T. They went through all the different combinations of Power + Volume Up/Down + Home buttons and could not fix the phone. Eventually after messing with it more, they stumbled on the "No command" dead android screen, at that point I just got a new phone. I took the S6 home for further trouble shooting, and was able to use Odin to flash the original firmware successfully.
However, now the phone now get stuck on "Installing update" screen (I've tried leaving it on this screen for 72 hours and it did not complete) when trying to restart the phone.
After trying going into recovery mode, the phone just restarts before I can select any options. I've tried scrolling down to factory reset, but before I can confirm pressing the power button, the phone freezes and restarts.
I've also tried letting the battery die out, and starting over, however, I'm unable to even get the battery charging screen to come up after the phone dies. The phone now always has a white/pink LED on whether the phone is plugged in or not.
I'm not sure where to go from here to fix the phone, any suggestions are greatly appreciated!
PM me for a link to an image of the recovery mode screen as I cannot yet post image links on the forums.
Hi , you can try the following steps :
- First let the battery to discharge out completely 0% if it stays on led light let him like that for 2 days to discharge the battery.
- After that put your phone to Original charger for 3 - 4 hours to be charged.
-Once your phone is charged go to the next step.
- Download this firmware :
https://drive.google.com/file/d/0By7ytf2nnXE8RGREVV9VRGxjNzQ/view
- Once you download extract on Desktop with 7-Zip and put each file to odin one by one (see short video) :
https://drive.google.com/file/d/0B5iuIvmgitAFZFlhU3dqSTdRNm8/view
- Try to put your device into Download mode , VOl - + Home + Power button ....
Good luck
Teddy Lo said:
Hi , you can try the following steps :
- First let the battery to discharge out completely 0% if it stays on led light let him like that for 2 days to discharge the battery.
- After that put your phone to Original charger for 3 - 4 hours to be charged.
-Once your phone is charged go to the next step.
- Download this firmware :
- Once you download extract on Desktop with 7-Zip and put each file to odin one by one (see short video) :
- Try to put your device into Download mode , VOl - + Home + Power button ....
Good luck
Click to expand...
Click to collapse
Hey Teddy, Thank you for the info. I've tried letting the battery die out and re-flashing with a G890A_G890AUCS7DRA2_ATT_USA_v7.0.1 folder found elsewhere. I'll try letting the battery die out again and re-flashing with the source you provided. Cheers.
Hey Teddy, small update, the ZIP file you linked me for the firmware is password protected, would you happen to know the password to unzip the folder?
Hi , try this password: [email protected] or just thonguyen.info .