Help took back off my hdc s6 clone to see what battery was in to see about changing it and a ribbon from the battery snappednot sure how you get to where it goes and can I get a replacement if needed
thanks
A ribbon? you mean like the connector 'cord' to your logic bord snapped?
yes basically its that have got the other end off now. But when looking at battreys they all seem different mine as a circuit board on the end with a longer ribbon and the port is side off the battery almost in the centre
Related
Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
i have the same problem with my x10 but i have warranty but whilst i was waiting for them to collect it, i cut my usb lead up and stripped the black and red cables back obviously positive and negative and took the battery out and wedged each cable on the phone connector with the battery my battery had a plus and negative signs on it so was easy 2 work out, it charges the battery but it doesnt come up as charging on the phone it will still blind red lights but doesnt turn off, you have to keep and eye on the charging levels on the phone status do not let it go over 99% as this method dont tell the battery to stop charging, also this is not full proof and could break your x10 if not dont correctly,but as for your question the usb port does need to be soldered good luck
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
Hi John,
I fixed my friends USB port, you will need:
"helping hands" (a tool for holding small things with a magnifying glass)
0.5mm or 1mm Soldering iron
Hot glue
Under the magnifying glass, there you will see the 5 pins the usb port was solderded onto. You will need to put a little bit of solder onto each pin and onto the board.
Hold everything together with the helping hands, and just tick the soldering blobs with your iron. This will connect all the points. Do not solder for to long, or you will bridge pins or remove the solder.
Continue until all 5 is connected. Solder the 2 points on the side (holds the USB port, you could do this first if you don't have the helping hands)
plug in cable, use multimeter to see if there is current by you battery pins.
Voila.
If no power then you have to follow one of those fixes online where you have to bridge the doide and the V+ port.
Thanks for the info, like I said the phone is dead anyway, so I can't really make it any worse (That's what I keep telling myself anyway).
It the parts were a lot bigger, I probably wouldn't be bothered as much, but if I do get it wrong, I'm hoping I can take it off, remove the solder and just start again. (hopefully)
I think I have a good idea now of what I'm supposed to be doing, but I'll probably have to wait till I get a new soldering iron, as mine is a little bit too big.
Thanks ...John...
yup face-palm he had his s3 in back pocket riding bicycle drunk home, fell off bike right on backside, phone taking most the impact.
the screen doesnt seem to be cracked just a small chip on the edge near camera.
he had it in a double sided leather padded case so we dunno how it got chipped
very small crack on body above usb port, but i think that crack is common.
the main point being the phone will now not switch on, is not charging or accessible via usb. no led nothing. button combo's do nothing. battery change no help
do you guys reckon it'll b worth replacing the usb port? or just a spares repo?
you can't replace the usb port unless you buy a motherboard, desolder one from there and solder it on your old one, which obviously doesn't make sense and won't work anyway, because the phone is clearly broken. The phone would switch on if the port was broken if there was any charge in the battery
Glebun said:
you can't replace the usb port unless you buy a motherboard, desolder one from there and solder it on your old one, which obviously doesn't make sense and won't work anyway, because the phone is clearly broken. The phone would switch on if the port was broken if there was any charge in the battery
Click to expand...
Click to collapse
well you can just buy the usb ports from part stores.
and yup i made another face-palm, its not the usb as a fully charged battery wont power it lol
im just gonna assume when he landed on it he just bent the motherboard and crushed something/many parts lol.
kinda strange he damaged the internal parts but not the screen.
he bought it like 6months ago so i doubt samsung or t-mobile will help eh.
oh well, what divv rides a bike with an s3 in theyre back pocket?
Hi,
I've been searching and trying to find the correct part to replace the USB charging port without losing the signal. I've gone through different part numbers from different vendors but they always end up being cut up and the original antenna board is placed for the signal to work. Did anyone here have success replacing the charging port board AND signal works with the same board? Can you share the vendor/part number? I'm afraid that cut out of antenna side from the original board will die on me and I'll be stuck with tiny tablet.
Phone is i777.
Hey there all, about a month ago i dropped my phone into the river, ordered a replacement battery (because it was bulging out) and was able to recover my phone from water damage. Had to use isopropyl to clean all the board contacts, but i think i may have fried my mic and gyrometer parts. I was wondering if there were replacement parts for these or if there was another method to test if i need to reclean them again. Also have some charging issues after replacing my battery, so im wondering whether i should replace my usb charging flex port and whether i should also replace my antenna cable cause my signals a little bit worse than original. Cheers! I need to know if i replace the usb dock port, can i use other versions other than the g925i ie 925f etc, thanks