My phone has been bricked - Galaxy S III Q&A, Help & Troubleshooting

Please help. My s3 can only boot into twrp logo and stays there while flickering every few seconds. I have tried the volume up, power button and home button thing and still it does nothing but reboot to the same place. In short, I cannot enter recovery mode to re-flash my phone.

What about download mode? Volume down Power and Home button?

savor_savvy said:
Please help. My s3 can only boot into twrp logo and stays there while flickering every few seconds. I have tried the volume up, power button and home button thing and still it does nothing but reboot to the same place. In short, I cannot enter recovery mode to re-flash my phone.
Click to expand...
Click to collapse
What about entering download mode ? As it was stated above ? Then you can download last stock firmware for your region and flash it via Odin. Good source of original firmware is //samsung-updates.com/. Odin is available at many sites. If you run Win7 (or higher) on your PC you do not need any additional software, if not - proper drivers to see your mobile will be required. Then, if you do not want to stay with stock ROM, you can flash custom recovery and finally custom ROM chosen from dozens of them...

Related

[Q] Interesting Problem rooting device

I installed this kernel from Chainfire's thread: CF-Root-SGS2_XW_XEU_KH4-v4.1-CWM4.tar
However, my phone says that I have the KH7 kernel, but I figured this one ( KH4 ) would be close enough. It flashed fine, and I have root access and all, but my back button no longer works at all (not even haptic), and my Home button is acting like a back button - meaning I essentially have lost my Home button...
But now that my device is rooted, when I boot into debug mode, I get the CWM menu, meaning I can no longer use Odin correct? But because my home button is gone, I cannot select "install zip from sd card"
My question is this: Without the use of the Home button on my device, is there anyway to flash a new kernel?
Thanks to anyone who can answer this.
You just flashed cf root for the INTERNATIONAL SGS2 and NOT FOR THE ATT SGS2. That is why you lost some buttons. Make sure to use ATT SGS2 ROMS/KERNELS. There is a post about how to fix your issue in the att section to get you back to the att version of the SGS2.
Brought to you by my KICKASS CM7 AT&T SGS2
I realize I flashed the wrong version, but my question is how do I flash a different version without the use of my Home key? That is the issue.
sicvita said:
I realize I flashed the wrong version, but my question is how do I flash a different version without the use of my Home key? That is the issue.
Click to expand...
Click to collapse
You boot into Download mode and flash the right one in Odin. How hard is that.
Sent from my SAMSUNG-SGH-I777
Can I still use Odin even if I have already rooted the device? Do I just hold up vol + down vol + power to boot into download mode? I thought that was called debug mode...
From the FAQ:
How do I put my phone into Download mode so I can flash w/ Odin?
Take out the battery from the back to ensure your phone is completely off, then put the battery back in. Now hold down on both the Up and Down Volume buttons and plug the USB coming from your PC into your SGS2. Once you see a warning screen let go of the volume buttons. Hit the Up Volume button to continue into download mode.
I found that you can just click the volume down + power button to get into download mode.
I think everyone is missing the point of my question. Can I flash my phone with Odin EVEN IF I ALREADY HAVE CWR INSTALLED? I cannot use CWR to flash as I lost the use of my Home button (cannot select from the menu)
I resolved my own issue. There is a difference between RECOVERY mode and DOWNLOAD mode. To boot into recovery you hold vol up + vol down + power, to boot into download mode you JUST hold vol up + vol down, then plug into USB. I did not realize there were two different modes, sorry for wasting time and causing confusion.
Yup, you can always boot into download mode as long as you didn't flash a bootloader.
Another way of saying it is:
If the screen turns on at all, you can recover by flashing something correct in download mode.

Enter CWM Recovery

Please forgive if this have been answered before.
Is it possible to enter CVM Recovery directly in boot.. Not via CWM Manager?
Like on Xperia X10 you can press multiple times on the back button to enter xRecovery.
The reason I am asking this ridicilous question is that I am feeling ready to try a custom ROM, but if I mess something up, i.e. bootloop, phone stuck, etc. it is nice to get into recovery and install a backup (I NEVER install a custom ROM without a new backup - did it once - never again ).
Power off and then power on again whilst holding home and volume up. That enters recovery, or clockwork recovery if you have it.
Do the same, but with volume down to enter download mode (for flashing with the likes of Odin).
Archer said:
Power off and then power on again whilst holding home and volume up. That enters recover, or clockwork recover if you have it.
Do the same, but with volume down to enter download mode (for flashing with the likes of Odin).
Click to expand...
Click to collapse
Thanks a lot!

[Q] How to boot into CWMboot into CWM

I tried to flash a new rom, after wiping the data of my previus I noticed I haven't moved it into the external SD so I restared the mobile in order to move the .zip file.
At the point where you set a google account I tried to rush it though but at one point the phone restarted and from that moment on it always gets stuck in boot screen.I use the Omega rom.
How can I boot into CMW with "hotkeys" at the beggining of booting (Samsung logo)?
Things I tried:
Removing the batery for 1 min and restarting,
Almost all possible key combinations at the boot screen (Samsung boot) not the rom boot
CWM recovery
Hold down
Vol Up Button + Home Button + Power Button at first splash screen release buttons .
jje
Normal 3-Button Combo should work. Maybe you have to be fast after insert the battery again.
If you can't go there, try to get into download mode a start a fresh install with odin or heimdall.
cgriese said:
Normal 3-Button Combo should work. Maybe you have to be fast after insert the battery again.
If you can't go there, try to get into download mode a start a fresh install with odin or heimdall.
Click to expand...
Click to collapse
What is easier to use odin or heimdall?
ideally flash with odin to the T if your going to upgrade the rom to whatever you choose, it will do a full wipe for you bit of a pain losing your data but its really the only way of getting back up to scratch put it into download mode vol down - menu button + power button then an option will show press vol up and go from there be warned you must follow the odin instructions perfectly

[Q] safe mode 4.1.2, 4.0.4 volume button ,camera problem??

I have a i9300 s3. I upgrade to 4.1.2 jb , my phone become safe mode. however i try to get out but i failed.
1. restart by press back button
2. restar by press volume up button and other also cant get out from safe mode.
downgrade to 4.0.4
I press volume down key+ home key + power to downloader mode, and downgrade to 4.0.4 by odin. after downgrade 4.0.4, i go to recovery mode, but my volume own button not working. i use odin running to cwm recovery mode, press up volume button until can wipe factory reset and reboot, it' out of safe mode. but the volume down button no working after boot. When I press volume down key+ home key + power it still can go into downloader mode.
After 1 week, my phone auto download software upgarde and install to 4.1.2, but it cant cause cwm recovery mode disturb it. after that my camera no function at all. now i wanna try to go downloader mode again, but my phone volume up button also become no working at all to go downloader mode, but it working when the phone is on.
Actually whats was going on?? how can i upgrade to 4.1.2 ?? or i just can stay at 4.0.4 but now my camera no working.
Anybody looking for this problem before?? :crying::crying::crying:
That's one hell of an unlucky upgrade. I don't know mine upgraded/rooted without problem. Can't you just return to stock once you're able to enter download mode?
Fail to understand the problem be specific with current problem .
jje
sglong_noob said:
I have a i9300 s3. I upgrade to 4.1.2 jb , my phone become safe mode. however i try to get out but i failed.
1. restart by press back button
2. restar by press volume up button and other also cant get out from safe mode.
downgrade to 4.0.4
I press volume down key+ home key + power to downloader mode, and downgrade to 4.0.4 by odin. after downgrade 4.0.4, i go to recovery mode, but my volume own button not working. i use odin running to cwm recovery mode, press up volume button until can wipe factory reset and reboot, it' out of safe mode. but the volume down button no working after boot. When I press volume down key+ home key + power it still can go into downloader mode.
After 1 week, my phone auto download software upgarde and install to 4.1.2, but it cant cause cwm recovery mode disturb it. after that my camera no function at all. now i wanna try to go downloader mode again, but my phone volume up button also become no working at all to go downloader mode, but it working when the phone is on.
Actually whats was going on?? how can i upgrade to 4.1.2 ?? or i just can stay at 4.0.4 but now my camera no working.
Anybody looking for this problem before?? :crying::crying::crying:
Click to expand...
Click to collapse
First thing, and i don't pretend to be rude, write your question in the right way.
There are Forum Rules for all of US.
The second one, the download mode, is by pressing volume DOWN(not up)+HOME+POWER. The one you are choosing as far as i comprehend by you спасибоwords, leads totCWM (either stock or 3d party one).
The third, if you somehow managed to downgrade to ICS(4.0.4), just press OTA update
Cheers!
worf_1977 said:
First thing, and i don't pretend to be rude, write your question in the right way.
There are Forum Rules for all of US.
The second one, the download mode, is by pressing volume DOWN(not up)+HOME+POWER. The one you are choosing as far as i comprehend by you спасибоwords, leads totCWM (either stock or 3d party one).
The third, if you somehow managed to downgrade to ICS(4.0.4), just press OTA update
Cheers!
Click to expand...
Click to collapse
Actually when the phone boot on ICS 4.0.4 the volume up button is working and the volume down button is not working.
Ya, i know that the download mode is by pressing volume DOWN + HOME+POWER.
I can going to page WARNING!! a custom OS --------------- after need press Volume UP to continue and Volume DOWN to cancel, but the volume up and volume down button also not working.
Maybe is because my volume DOWN button problem, so make me headache.
I know that CWM (either stock or 3d party one). But i need it to wipe my factory reset after downgrade to 4.0.4 by Odin.
sglong_noob said:
Maybe is because my volume DOWN button problem, so make me headache.
When it was JB 4.1.2, It will boot on SAFE Mode, However how many times i reboot , reboot by press back key or up volume button too.
I cant get off from SAFE mode.
At the moment, I try to downgrade to ICS 4.0.4 by Odin. I can going to download mode. after Odin pass, It stuck at the samsung logo.
I try to go to recovery mode by press VOLUME UP + HOME + POWER. I can go to recovery mode but the Volume DOWN not working and i cant go to wipe reset.
I going to download mode again and running PDA with CWM tar. I use CWM recovery mode to going to wipe reset by press VOLUME UP button only. Pls try to understand this.
Once I wipe reset, I can boot my phone on ICS 4.0.4. The moment all function ok, camera too. Just the Volume DOWN button not working.
I use it for a week, Software upgrade automatic but it failed. It stuck on CWM recovery mode. I try reboot again, the Volume UP button is WORKING, the camera not working. The big problem is I cant go to download mode again, just stuck a WARNING page, and my volume UP and DOWN also not working when i stuck a warning page.
Click to expand...
Click to collapse
Whats I going to try is tomorrow I will buy the USB JIG and force my S3 to download mode and try upgrade to JB 4.1.1 or 4.1.2 the latest Version ( March ) by Odin again. Any suggestion too??
try installing phillz touch recovery in odin using the tar file you can use touch to go up and down also try installing stock 4.1.2
Or you can just issue an ADB reboot download
Sent from Quo'nos via subspace transmission
I'm on trying to 4.1.2 version now...
4.1.2 JB version, safe mode....
Volume down button not workin:crying:. camera workin right now.
I cant go to recovery mode by press UP + VOLUME + POWER:crying:
Now i down grade to 4.1.1
omg, it stuck on samsung logo..
maybe is because of I still didnt wipe factory reset but i cant go to recovery mode too. I press volume UP + HOME + POWER , it restart and restart, cant go to recovery mode too.
Whats can I do now??
I stuck over the samsung logo, cant going recovery mode by press volume UP + HOME + POWER
I try adb reboot recovery mode but
"error : device not found"
Have any idea to recovery mode??:crying::crying::crying:
Try in a terminal from thee phone itself.
Just type "su" and then "rebbot recovery"
Sent from Quo'nos via subspace transmission
worf_1977 said:
Try in a terminal from thee phone itself.
Just type "su" and then "rebbot recovery"
Sent from Quo'nos via subspace transmission
Click to expand...
Click to collapse
Now my phone cant boot, just stuck at samsung logo. i cant go to recovery mode....:crying::crying:
same issue here
sglong_noob said:
Now my phone cant boot, just stuck at samsung logo. i cant go to recovery mode....:crying::crying:
Click to expand...
Click to collapse
I also have a button stucked, which you can easily see in the bootloader, as it scrolls automatically all the options. It is hw issue, but wanted to know if there is a kernel or someway in which I can disable the volume rocker entirely.
Is there anyway to disable safe boot when booted up into safe boot. I can install apps but they will not open due to the fact that I am in safe mode. Anything will be greatly appreciated.
fdolande said:
I also have a button stucked, which you can easily see in the bootloader, as it scrolls automatically all the options. It is hw issue, but wanted to know if there is a kernel or someway in which I can disable the volume rocker entirely.
Is there anyway to disable safe boot when booted up into safe boot. I can install apps but they will not open due to the fact that I am in safe mode. Anything will be greatly appreciated.
Click to expand...
Click to collapse
Ya, now still dont have any solution yet..
Hope someone pro can help us.
Is it possible to get rid of the safe mode tru adb?
Tusnal said:
Is it possible to get rid of the safe mode tru adb?
Click to expand...
Click to collapse
Thanks you for reply. I'm sorry that I cant get to safe mode. Now my problem is My i9300 stuck on LOGO samsung.
I CANT go to recovery mode by Press VOLUME UP + HOME + POWER.
Any solution can force my i9300 to recovery mode??

Stuck at start-up, need help!

Hi!
Last night, I installed a new custom-firmware by using Baidu ROM flash tool (not exactly the Baidu ROM). After installation, my phone rebooted, and got stuck on "Baidu" logo (a screen before the user-interface).
Is there any way to flash another rom, or do some reset?
Thank you!
Probably you should have done a factory reset on your phone before flashing Baidu. You can do this through CWM, and after this you can flash Baidu rom.
Also, you can always flash stock roms with Odin.
freitaz said:
Probably you should have done a factory reset on your phone before flashing Baidu. You can do this through CWM, and after this you can flash Baidu rom.
Also, you can always flash stock roms with Odin.
Click to expand...
Click to collapse
But how do I install CWM on my phone. It's not even rebooting in the recovery mode by pressing VOL+, MENU, and Power button.
noman.rasheed said:
But how do I install CWM on my phone. It's not even rebooting in the recovery mode by pressing VOL+, MENU, and Power button.
Click to expand...
Click to collapse
Put your device on download mode (VOL -, menu, power buttons) and then flash CWM with Odin.
freitaz said:
Put your device on download mode (VOL -, menu, power buttons) and then flash CWM with Odin.
Click to expand...
Click to collapse
No! Not working for me. Is there any other way?
This is what it happens;
Samsung Logo - Samsung Galaxy Win GT-I8552 (appears on screen), and then Baidu Logo ; that's all!
Are you doing the process right? You must press the three buttons at same time; when your phone vibrates, you release only the power button but keep the other two pressed. A warning should appear on screen.

Categories

Resources