Root, cwm Recovery, Readback Micromax Canvas Nitro 2 3E11

Root, cwm Recovery, Readback Micromax Canvas Nitro 2 3E11 - Micromax Canvas Nitro A310/A311

Steps:
1. Download Mtk droid Tools, SP Flash Tools, drivers for your phone, (no need, just connect your e311 to pc and choose connect as buil in cd rom and install drivers).
2. People having windows 8/8.1/7 first of all disable driver signature verification(google it, pretty easy)
e.g. on windows 8/8.1 go to bottom right corner,choose setting on charm bar,select change pc settings, update and recovery,go to recovery,advance start up,restart, advance startup/troubleshooting, disable driver signature verification by pressing 7 on keyboard(you need physical keyboard, touch keyboard won't be there).
3. READBACK ROM BACKUP
i. open/run as administrator MTK droid Tools, your phone should be switched on, connect it,accept usb connection on phone, let the droid tools detect it and show its specifications.(make sure usb debugging is enabled)
ii. click on blocks map, a window tile of block info will pop up. Note down or better save it using notepad++/screenshot by pc or ms word file, you need values of preloader and userdata/(some other phones may show FAT,don't panic,it's just your internal sd partition) under scatter column(also note the values under size column for backing up a single item like recovery, for entire rom you only need scatter column values of preloader and userdata/FAT).
iii. alongwith block info, a tile asking to creat scatter file will pop up, create it. This will be our scatter file for SP Flash Tools.
iv. Disconnect usb, switch off phone. you may close mtk droid tools, it will be needed after next step.
4. Open/Run SP Flash Tools as administrator,
i. click scatter loading and select previously created scatter file.
ii. click on readback tab on sp flash tools..then click on add button.
iii. double click on the item (it should be checked in the selection box)and save it as ROM_0(default) or ROM_1 , it does not matter.This will be a large file approx 3.2 GB so save it to a dedicated folder on pc not usb.
iv. next readback block address tab will open, under start address value will be like 0x00000000, leave it as it is(don't change to 0x0), under length use the value under scatter column of userdata/FAT previously noted in block info..Make note that value entered should be like 0x1234567 and not like 0x0001234567. the zeros after 0x should be removed and only till first non zero value after that and middle zeros like 120458000 shoud be written as it is. The length value may be numeric for some phones but e311 will show like 0x000CDF7000, Don't worry enter it like 0xCDF7000. This is just example not actual value, i assume each phone will show different value.
v. after entering length and pressing ok, click readback and now connect switched off phone.
vi. after that click ok and wait for readback to complete. It will take about 7-11 minutes depending on your pc processor. a green check will appear on completion.
vii. close Sp flash tools, disconnect usb. switch on phone.
5. Open MTK droid tools,connect switched on phone,select the root,backup,recovery tab.
6.Click*To*process*file*ROM_*from*Flash*Tool.
7. *Select*the*ROM_1*file*you*saved*in*the*step*above*in*the*window*that*pops*up.
8.*Wait*for*MTK*Droid*tools*to*finish*copying.
9. *When*prompted*to*make*CWM*Recovery*automatically,*click*Yes*or*No*.*If*you*click*Yes,*you'll*need*to*select
the*Recovery.img*from*the*window*that*pops*up.This will make cwm recovery, take backup of stock recovery.
10. Your Rom backup will be in MTK DROID TOOLS/backup folder. You can now flash cwm created in backup with Sp Flash Tools and also root your phone by flashing supersu.

hem.crz said:
Steps:
1. Download Mtk droid Tools, SP Flash Tools, drivers for your phone, (no need, just connect your e311 to pc and choose connect as buil in cd rom and install drivers).
2. People having windows 8/8.1/7 first of all disable driver signature verification(google it, pretty easy)
e.g. on windows 8/8.1 go to bottom right corner,choose setting on charm bar,select change pc settings, update and recovery,go to recovery,advance start up,restart, advance startup/troubleshooting, disable driver signature verification by pressing 7 on keyboard(you need physical keyboard, touch keyboard won't be there).
3. READBACK ROM BACKUP
i. open/run as administrator MTK droid Tools, your phone should be switched on, connect it,accept usb connection on phone, let the droid tools detect it and show its specifications.(make sure usb debugging is enabled)
ii. click on blocks map, a window tile of block info will pop up. Note down or better save it using notepad++/screenshot by pc or ms word file, you need values of preloader and userdata/(some other phones may show FAT,don't panic,it's just your internal sd partition) under scatter column(also note the values under size column for backing up a single item like recovery, for entire rom you only need scatter column values of preloader and userdata/FAT).
iii. alongwith block info, a tile asking to creat scatter file will pop up, create it. This will be our scatter file for SP Flash Tools.
iv. Disconnect usb, switch off phone. you may close mtk droid tools, it will be needed after next step.
4. Open/Run SP Flash Tools as administrator,
i. click scatter loading and select previously created scatter file.
ii. click on readback tab on sp flash tools..then click on add button.
iii. double click on the item (it should be checked in the selection box)and save it as ROM_0(default) or ROM_1 , it does not matter.This will be a large file approx 3.2 GB so save it to a dedicated folder on pc not usb.
iv. next readback block address tab will open, under start address value will be like 0x00000000, leave it as it is(don't change to 0x0), under length use the value under scatter column of userdata/FAT previously noted in block info..Make note that value entered should be like 0x1234567 and not like 0x0001234567. the zeros after 0x should be removed and only till first non zero value after that and middle zeros like 120458000 shoud be written as it is. The length value may be numeric for some phones but e311 will show like 0x000CDF7000, Don't worry enter it like 0xCDF7000. This is just example not actual value, i assume each phone will show different value.
v. after entering length and pressing ok, click readback and now connect switched off phone.
vi. after that click ok and wait for readback to complete. It will take about 7-11 minutes depending on your pc processor. a green check will appear on completion.
vii. close Sp flash tools, disconnect usb. switch on phone.
5. Open MTK droid tools,connect switched on phone,select the root,backup,recovery tab.
6.Click*To*process*file*ROM_*from*Flash*Tool.
7. *Select*the*ROM_1*file*you*saved*in*the*step*above*in*the*window*that*pops*up.
8.*Wait*for*MTK*Droid*tools*to*finish*copying.
9. *When*prompted*to*make*CWM*Recovery*automatically,*click*Yes*or*No*.*If*you*click*Yes,*you'll*need*to*select
the*Recovery.img*from*the*window*that*pops*up.This will make cwm recovery, take backup of stock recovery.
10. Your Rom backup will be in MTK DROID TOOLS/backup folder. You can now flash cwm created in backup with Sp Flash Tools and also root your phone by flashing supersu.
Click to expand...
Click to collapse
Bro can you plz tell how to install drivers ,mtk droid tool is not detecting e311.along with download links of drivers. Mine windows is xp
Sent from my Micromax E311 using XDA Free mobile app

akashjasani13 said:
Bro can you plz tell how to install drivers ,mtk droid tool is not detecting e311.along with download links of drivers. Mine windows is xp
Sent from my Micromax E311 using XDA Free mobile app
Click to expand...
Click to collapse
Installing Drivers for Micromax Cannvas Nitro 2 E311:
(A) Enable usb debugging on E311:
1. Go to settings, about phone, tap on build number 7 times to enable developer options.
2. Select developer option, check box for usb debugging, thats it.
3. Also allow installation of apps from unknown sources under Personal/security in settings menu...useful for installation of apps that are not from play store.
(B) Install Drivers:
1. Connect Switched on or even switched off phone with pc via usb cable. It will automatically install driver.
If step 1 does not work for you then
2. Connect your phone via usb, it will be connected as MTP Device. Change it to connect as Built in CD Rom. It will show as cd drive/micromax e311.
3. Open it, there will be drivers folder alongwith usb guide(useless).
4. Inside drivers folder, there is drivers auto installer,within that folder you will find drivers with installation instruction on excel sheet.
It should work but even if it does not then search google for auto drivers installer for micromax devices or pda net or drivers for specific model no. like e311, a311, etc.
MTK DROID Tools Not reading phone:
1. Just check if you have usb debugging allowed or not. If not then do so as explained above.
2. When you connect switched on phone via usb to pc, MTK Droid Tools should be running as administrator(not necessary on windows Xp).
3. After running MTK Droid Tools and connecting usb, a message will pop up on phone asking to allow/accept usb debugging for droid tools, allow/accept it.... wait for few seconds and MTK droid tools will show info for E311 as connected.
In case of difficulties search mediafire.com for drivers, picture guide for readback backup,root and recovery, cwm image and MT6592_Android_scatter uploaded by me. I was trying to post them here but XDA won't allow it as it's my 2nd post only and they allow it after 10 posts only. I'm giving the file names as searching will be easier i hope
1. How_to_Get_Stock_ROM_RomDump_of_Mediatek_MT6582_via_MTK_Droid_Root_and_Tools_-_GSM-Forum.pdf
2. Micromax-E311_150522__recovery_150724-082456.img
3. MT6592_Android_scatter.txt
4.How_to_make_a_ROM_backup_Dump_using_Sp_Flash_Tool_Read_Back.pdf
5. Supersu
6. Drivers for Micromax E311

hem.crz said:
Installing Drivers for Micromax Cannvas Nitro 2 E311:
(A) Enable usb debugging on E311:
1. Go to settings, about phone, tap on build number 7 times to enable developer options.
2. Select developer option, check box for usb debugging, thats it.
3. Also allow installation of apps from unknown sources under Personal/security in settings menu...useful for installation of apps that are not from play store.
(B) Install Drivers:
1. Connect Switched on or even switched off phone with pc via usb cable. It will automatically install driver.
If step 1 does not work for you then
2. Connect your phone via usb, it will be connected as MTP Device. Change it to connect as Built in CD Rom. It will show as cd drive/micromax e311.
3. Open it, there will be drivers folder alongwith usb guide(useless).
4. Inside drivers folder, there is drivers auto installer,within that folder you will find drivers with installation instruction on excel sheet.
It should work but even if it does not then search google for auto drivers installer for micromax devices or pda net or drivers for specific model no. like e311, a311, etc.
MTK DROID Tools Not reading phone:
1. Just check if you have usb debugging allowed or not. If not then do so as explained above.
2. When you connect switched on phone via usb to pc, MTK Droid Tools should be running as administrator(not necessary on windows Xp).
3. After running MTK Droid Tools and connecting usb, a message will pop up on phone asking to allow/accept usb debugging for droid tools, allow/accept it.... wait for few seconds and MTK droid tools will show info for E311 as connected.
In case of difficulties search mediafire.com for drivers, picture guide for readback backup,root and recovery, cwm image and MT6592_Android_scatter uploaded by me. I was trying to post them here but XDA won't allow it as it's my 2nd post only and they allow it after 10 posts only. I'm giving the file names as searching will be easier i hope
1. How_to_Get_Stock_ROM_RomDump_of_Mediatek_MT6582_via_MTK_Droid_Root_and_Tools_-_GSM-Forum.pdf
2. Micromax-E311_150522__recovery_150724-082456.img
3. MT6592_Android_scatter.txt
4.How_to_make_a_ROM_backup_Dump_using_Sp_Flash_Tool_Read_Back.pdf
5. Supersu
6. Drivers for Micromax E311
Click to expand...
Click to collapse
Thank you for the expanation i already had install driver from built cd rom but adb android interface/htc android interface is showing exclamation mark on device manager
Sent from my Micromax E311 using XDA Free mobile app

Use kingroot. Its 100% working. Try it.
Sent from my Micromax E311 using XDA Free mobile app

What about custom rom for this device
Sent from my Micromax E311 using XDA Free mobile app

Can any one please give me Custom rom for this device ?

stuck
after i flashed cm 12.1 from one of the threads using cwm everything was working fine but after i made a data wipe it won't turn on . and it had low battery so after a while it turned off . now even the pc is not recognizing it . i don't know what to do , someone please helpppp

Related

HKC p771a 7 inch Tablet Root

I have used many different methods to root phones even a few tablets for friends. But I have bought a HKC 7 inch tab from walmart. Great starter tablet by the way. I have found no information what so ever on any forum about this model. It has decent processor power and runs rather smooth. Alas there is no way to root this thing to reach its full potential. I checked around on the net and found nothing, none of the one click apps work on this model. Adb does not recognize the tablet either. I've put in the tablet ID into the adb_usb.ini still no device found. I'm not looking for anyone to just hand me the root process on a silver plater, though that would be nice, but any help moving me in the right direction would be appreciated.

I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment Rockusb.rar
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon

New approach
Ok I cannot get the drivers to install on my computer. Window 7 seems to default to its own driver and will not let me install the rockusb drivers.
With that said, I have the system Update.img and was wandering if the img itself can be rooted and then updated to the tablet. If this is possible and anyone with the knowledge is willing I will upload it. Or if someone is really patient and would like to walk me through the process and I will attempt to do this myself

No Help
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.

tannerjames said:
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.
Click to expand...
Click to collapse
Can't tell your level of PC knowledge so if you already know this don't get offended. The .inf is editable and there are areas in there that allow manufacturers to prevent installation on some OS's to prevent conflicts. Make a system restore point or better yet a backup and then post the contents of the INF somewhere and point the folks here to it and they may be able to help you edit it to install. Regardless, you'll have to use the "have disk" option instead of letting windows search for a driver even if you get the edits right. And the usual disclaimers about me not being responsible for any issues with your equipment as a result of this are in effect.

tannerjames said:
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.
Click to expand...
Click to collapse
I was able to root using the instructions above although i don't think you need the rockusb drivers. You just need the usb drivers that come with the android sdk. I am on Win 7. Thanks for the above info for rooting.
I was able to install ROM manager and now proceeding to backup ROM and upgrade using this guide: cant post link as forum is preventing, but search for rom flash guide on androidpolice com.
Hope this helps.
Big thanks to this thread to get me going...!!!

?
could someone please, Barney style, Explain how I am supposed to select the android_winusb.inf because my steps are as follows. Right click on device p771a in device manager, browse my computer, let me pick from a list of device drivers, have disk, point to the google usb driver (C:/Android/android-sdk/extras/google/usb_driver) select the android_winusb.inf open. Hit ok, (The folder you specified doesn't contain a compatible software driver for you device. If the folder contains a driver, make sure it is designed to work with windows for x64-based systems). Hope this helps explain my troubles. Glad that my thread is helping others to root this device but it does not work for me.

Could it really be that simple?
Found in another forum about the nexus 7 when connected to the pc there is a presistent notification that allows you to change the connection type from mpt to camera which will give you adb access and the tool from this thread works great. Thanks for the help guys, got my root on

tannerjames said:
Found in another forum about the nexus 7 when connected to the pc there is a presistent notification that allows you to change the connection type from mpt to camera which will give you adb access and the tool from this thread works great. Thanks for the help guys, got my root on
Click to expand...
Click to collapse
Glad you could figure it out...
I was not able to use the ROM Manager to backup the ROM since the device is not supported on this tool, but see below for how you can obtain the stock image.
I've tried to flash multiple different ROMs using RKAndroid to the tablet, spending days on this, with no success. The tool itself works great and I am able to flash the ROMs since it supports the RK29 chipset which I believe this tablet has. The stock ROM for this device is available from the manufacturers web site (the link is available when you go to Settings => About Device => System Update, hkcdigital dot com slash update slash update.img), if anyone would like to take the stock rom and upgrade it to Android 4.2/JB.
I was able to unpack/repack the stock image using the wendal image tools and modify / cook the ROM using Android kitchen method described elsewhere in this forum. Rockchip Batch Tool is another great utility to flash custom ROMs to this device. Also, If you put the ROM as update.zip or update.img file on the microSD card, the tablet will take it and flash the image as long as it is in the right format. Ofcourse you can put the tablet into recovery and restore from there as well. I've found that the stock image (update.img) has the following file/folder format when unpacked: /RK29xxLoader(L)_V2.27.bin, /package-file, /parameter, /recover-script, /update-script, /Image/boot.img, /Image/system.img, /Image/recovery.img and /Image/misc.img.
Is it possible to upgrade this tablet to Android 4.2 or atleast Jelly Bean? Would be very helpful if someone is able to do this. The most success I've had so far is with the custom ROM Oma_Odys_Loox_JB_4.1.1_v1.2.2a flashed using RKAndroid. It flashed the tablet fine, updated the boot etc. On tablet boot I am able to see the new logo, but then the it doesn't go anywhere from there. I think customizing this ROM or the stock ROM we should be able to get the new OS on to the HKC tablet. I've given up for now since I don't have the time to spend on this anymore. If someone is able to do this, please post the instructions or upload the custom ROM, as I am sure it will benefit a lot of people and will be much appreciated. Happy cooking!
Thanks!

jawadshaik- rom manager
If you have successfully flashed rom manager on this device could you post the steps you took to do so. What version? Manual flash? The program itself says there is no recovery for this device.

Sorry jumped the gun on that last post. Thanks for the info

What's the secret to keeping the battery from draining so quickly while it's idle? I just got this and see it drained about 40% in about 2 hours I think and I wasn't using it.
tannerjames said:
I have used many different methods to root phones even a few tablets for friends. But I have bought a HKC 7 inch tab from walmart. Great starter tablet by the way. I have found no information what so ever on any forum about this model. It has decent processor power and runs rather smooth. Alas there is no way to root this thing to reach its full potential. I checked around on the net and found nothing, none of the one click apps work on this model. Adb does not recognize the tablet either. I've put in the tablet ID into the adb_usb.ini still no device found. I'm not looking for anyone to just hand me the root process on a silver plater, though that would be nice, but any help moving me in the right direction would be appreciated.
Click to expand...
Click to collapse

@jawadshaik
Just out of curiosity, when you were flashing that Rom that brought up the boot screen, did you do a wipe/factory reset from recovery mode before flashing? I have no idea if that would help or not, but most if not all roms require a data wipe before flashing... Just curious if you had tried this as I have heard of this happening on other devices because a data wipe wasn't done first. Might be worth a shot if you haven't tried it already, just a thought
Sent from my Huawei u8651s using xda app-developers app

Krytical said:
I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment 1468367
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon
Click to expand...
Click to collapse
So after doing working on this a while, I've finally figured it out. Here are some caveats:
1. You can't do this on a Mac or Linux box. Don't ask me why, you just cant.
2. You have to turn on USB debugging, change the Security to allow Unknown sources and MOST IMPORTANT: when you plug it in, you have to change it to "Connected as a Camera". Putting it in storage mode doesn't work!
HOW TO INSTALL THE PROPER DRIVER & ROOT THE DEVICE:
1. Follow the steps quoted above and download the Google Android SDK, and the Java JDK (from oracle.com/java).
2. When you first plug it in (use the USB plug labeled USB not the HOST one), it complains and will discover a P771A device. When it does, right click on your computer, choose Manage my computer, go to the device manager and then right click on the P771A device. Click "Update Device Driver". Choose "Browse my computer for Driver software". Then choose, "Let me pick from a list of drivers on my computer". Browse to the \adt-bundle-windows-x86_64\sdk\extras\google\usb_driver folder which you would have if you had downloaded and installed the Google Android SDK. A list of 3 drivers will appear when you click OK. CHOOSE THE "ANDROID BOOTLOADER INTERFACE" as the driver. None of the others work.
3. Run the root script batch file mentioned above which can be found here at: sourceforge.net/projects/androidroot
4. The root script isn't really great at explaining so I'll try. When you first run it, make sure your device is unlocked and on the home screen.
5. The first thing it will do is reboot your machine. Don't press enter until your machine comes back up.
6. After your machine boots unlock it and then press Enter again. Your machine will reboot. This time it won't seem to come up but the backlight will remain on.
7. Wait about 30-45 seconds then press enter again. You should get: uid=0(root) gid=0(root) in the command prompt window.
8. Press Enter. You should get:
remount succeeded
727 KB/s (22364 bytes in 0.030s)
Removing changes except ROOT...
Installing superuser...
2288 KB/s (843503 bytes in 0.360s)
9. After about 30-60 seconds, your device should reboot. You'll see a box briefly saying "Android is Upgrading" and you'll arrive at the lock screen. Press Enter to exit the command prompt.
Your device is now rooted and you should see "SuperUser" installed. I promptly installed "root uninstaller" to get rid of Facebook, Skype, and Youtube which my little kids don't need access to. This device doesn't have a bootloader or recovery mode so rooting it doesn't get you much besides the ability to uninstall the system software. Have fun.

This may help someone but on step 2 of the guide on the second page, after you right click your device and go to "Let me pick from a list of drivers on my computer". You then click "Show All Devices" then "Have Disk..." Direct it to the root of the adt-bundle folder you downloaded then you can select from the three drivers. I'm on windows 7 32bit and the drivers didn't show up for me like how it was suppose to..

I also could NOT get any of the drivers in the "manufacturer USB" packet to install... I WAS able to install the google drivers, but that also would not allow ADB to see the device... So still stuck with everyone else...

P771A possible problem
I'm having a similar problem where the USB driver downloaded through Android SDK's -> Extras -> Google USB Driver, tells me that the file contains no information about my device. I noticed in the Sources of SDK, there wasn't an API for 4.0.4, only 4.0.3 then 4.1, so i downloaded 4.0.3 repo.
============================================
my devices is on 4.0.4, and my Kernal is as follows:
3.0.8+
[email protected] #8
Wed Aug 29 09:59:19 PDT 2012
Build Number:
P771A-user 4.0.4 IMM76D user.v402.007 release-keys
============================================
I've also made sure weather Unknown Sources is on, as well as USB debugging.
Might the Kernal be the problem? Also, does it matter weather its MTP or CTP?

Now HKC is telling me that they don't support the ability to jail break their devices
Sent from my P771A using xda app-developers app

Help with Rooting Zoostorm SL8 mini.

Hello could anyone please help me with rooting my zoostorm sl8 mini running ICS. I just don't know which rooting program to use and with one will work. I have search the web now for days and cant find anything.
Please Help!
Thanks:good:

Use the Qemu exploit
This can device can be rooted using DoomLords Xperia script. I have ported the script to linux as well for Ubuntu users,
The original script is here : http://forum.xda-developers.com/showthread.php?t=1601038
I haven't tested the Windows script, but I assume it will work as I haven't changed anything, the Linux script has been fully tested and I have successfully rooted the sl8 mini using it.
For Windows see below:
1) Download the attached zip file and Super1Click zip file ( http://download.cnet.com/SuperOneClick/3000-2094_4-75447027.html ).
2) Unzip the zip files into a new folders (you can use 7-zip for this : http://www.7-zip.org/)
3) Power on the Zoostorm Sl8 Mini and boot it normally.
4) Go into settings, developer options and tick USB debugging
5) Go to settings, security and tick Allow installtion of non-Market Apps
6) Connect the table to the PC with a USB cable.
7) When the new Hardware Found Wizard find the Android device and can't find a driver, select install from speficic location and browse to drivers folder under the folder you just unzipped the Super1click file to.
8) The driver should install from here and will show as an Acer Android device.
9) If Windows complains about the driver not being signed tell it to continue anyway.
10) Reboot the Windows PC if requested by the Hardware installation Wizard.
11) Discconect and replug the USB cable.
12) Open a windows command prompt
13) Navigate to the folder where the unzipped rootsl8mini.zip files are.
14) type runme.bat
15) Read the blurb on the screen and press any key to root your tablet.
16) The Sl8 mini will reboot several times, after it has reboot for the last time your sl8 mini will now be rooted.
For Linux (Ubuntu Precise Pangolin)
1) Install Android SDK, make sure the folder where adb is located is in your shell path variable. See link for Ubuntu instructions (http://www.liberiangeek.net/2012/07...-androidsdk-in-ubuntu-12-04-precise-pangolin/)
2) Download the attached rootsl8mini.zip file and unzip it into a folder.
3) Go into the folder where you unzipped the file and make the runme.bat.sh file executable. (Myhost:$ chmod 777 runme.bat.sh)
4) Power on the Zoostorm Sl8 Mini and boot it normally.
5) Go into settings, developer options and tick USB debugging
6) Go to settings, security and tick Allow installtion of non-Market Apps
7) Connect the tablet to the PC with the USB cable.
8) Execute the runme.bat.sh script (Myhost:$ ./runme.bat.sh)
9) Read the blurb on the screen and press any key to root your tablet.
10) The Sl8 mini will reboot several times, after it has reboot for the last time your sl8 mini will now be rooted.
Enjoy

Thank you, do I go to unzipped file using command prompt?
Thanks

I have tried to root the tablet and it wont install the drivers, it keeps saying that the file is corrupted or missing.
I'am running windows 8 64.
any suggestion's why it is doing this?
Many thanks :good:

I`m a noob to the Zoostorm. Are there any JB / CM10 ports for it?
Are they known as another name elsewhere in this forum?
Can anyone shed any light on this? Fantastic write-up by mikel by the way. Will test as soon as the mother-in-law gets hers for xmas from us!

Superb MIKEL543 i have done it, thank you so much, it took me a bit to figure it out but i managed to do it YAY..lol.
Now the problem is i cant watch and films from google play or flixster as it say that it cant because my Tablet is rooted .
i have tried everything and cant get it to work! :good:

easy way to root : http://zoostormsl8.blogspot.co.uk/2013/02/root-zoostorm-sl8-mini-3310-9506.html
download and update the zip

Bought this tablet as a gift for my father and assumed that connecting it to a usb keyboard would be straightforward (yeap android noob ) . My question is , is that even possible? Is there a custom rom that can be installed, I presume after rooting the device that enables usb host mode?

[Q] Ninja A87 problem

hello sir,
i have rooted my micromax ninja a 87 by this ;process given below
unlock root says it has rooted my phone and there i have supersu app too in my mobile when i open it it say su binary needs to be updated i click on ok and installation failed
i then installed superuser latest version and tries to update my binary again but it say that gaining root access .... Fail
i then tried SU update fixer but it also shows Gaining root access fail ...
please help i really want to root my phone and make full use of it thanks,
Aditya
1. Download jdk 32bit only from here, Android sdk from here, Unlock root from here, adb_usb.ini from here and A87 drivers from here.
2. Install jdk
3. install Android sdk, after installing open sdk manager form star and select "android sdk platform-tools" and "google usb driver" unselect the rest, click install packages. After installing put the adb_usb.ini file in "C:\Users\(your PC name)\.android"
4. Now on your phone goto settings>applications>development>enable usb debugging and connect usb cable, it should say usb debugging mode and show a little green android icon on the topleft (if not then reinsert cable or re enable usb debugging)
5. Windows will detect the device, let it stabilize then extract A87 drivers to a location say "C:/drivers"
6. Now goto start type "device manger" open device manager, you wil find "android adb interface" right click upgrade drivers and lead it to a location of your extracted drivers, do the same with other devices you get with an exclamation icon. (dont worry if you dont find other devices, its fine)
7. Install Unlock root, open it and click root, it wil ask for the device select micromax A87 and Your done !!!
8. Press Thanks !! Have a nice day !!

Aditya Kaushik said:
hello sir,
i have rooted my micromax ninja a 87 by this ;process given below
unlock root says it has rooted my phone and there i have supersu app too in my mobile when i open it it say su binary needs to be updated i click on ok and installation failed
i then installed superuser latest version and tries to update my binary again but it say that gaining root access .... Fail
i then tried SU update fixer but it also shows Gaining root access fail ...
please help i really want to root my phone and make full use of it thanks,
Aditya
1. Download jdk 32bit only from here, Android sdk from here, Unlock root from here, adb_usb.ini from here and A87 drivers from here.
2. Install jdk
3. install Android sdk, after installing open sdk manager form star and select "android sdk platform-tools" and "google usb driver" unselect the rest, click install packages. After installing put the adb_usb.ini file in "C:\Users\(your PC name)\.android"
4. Now on your phone goto settings>applications>development>enable usb debugging and connect usb cable, it should say usb debugging mode and show a little green android icon on the topleft (if not then reinsert cable or re enable usb debugging)
5. Windows will detect the device, let it stabilize then extract A87 drivers to a location say "C:/drivers"
6. Now goto start type "device manger" open device manager, you wil find "android adb interface" right click upgrade drivers and lead it to a location of your extracted drivers, do the same with other devices you get with an exclamation icon. (dont worry if you dont find other devices, its fine)
7. Install Unlock root, open it and click root, it wil ask for the device select micromax A87 and Your done !!!
8. Press Thanks !! Have a nice day !!
Click to expand...
Click to collapse
Go here for details :
Micromax A87

hello sir,
i have rooted my micromax ninja a 87 by this ;process given below
unlock root says it has rooted my phone and there i have supersu app too in my mobile when i open it it say su binary needs to be updated i click on ok and installation failed
i then installed superuser latest version and tries to update my binary again but it say that gaining root access .... Fail
i then tried SU update fixer but it also shows Gaining root access fail ...
please help i really want to root my phone and make full use of it thanks,
Aditya
Click to expand...
Click to collapse
I too faced the same problem a while ago :crying:, but at last got its solution...
Do this only if you Have CWM(clockworks mod) installed on your device...
If not then goto - http://forum.xda-developers.com/showthread.php?t=1987020
And find it there...
Firstly, Get a rooted custom/stock ROM and save it in your device's sd card,
Then goto ClockWorks Recovery ( First power off your device, then hold volume up and power key untill superfone logo displays to get into recovery menu), (scroll up and down for three times to enable the power button with vol. up and down key)open 'mounts and storage' menu
Then choose 'format/system' . After the completion Goto main menu and choose 'install zip from sd card' -> choose zip -> And install it.
And after completion, Reeboot. DONE, your got a rooted device...!

[TUT]Root And Install Clock Work Mod Recovey(CWM) Any MediaTek Device!!!!!!!

In most cases an android phone user comes to know about ROOTING and Installing Custom Recovery like CWMR, TWRP and Philz......Popular System on a chip manufacturer(Soc) like Qualcomm has been in the industry since 1985 and has a strong foundation and many of the flagship companies like sam, sony, lg, are using their Soc's. So somewhat developers are very eager to develop for these devices and let the other manufacturer down in their developer community(But not now a days).
So here we present the Ultimate guide for the media tek device owners on how to root and install Clock Work Mod Recovery for their phones.
ROOTING
One of the Best tools for rooting your phone is using FRAMAROOT which was developed by alephzain (Senior Member at XDA)
Just use any one of the exploit, Try the available exploit......IT will not ruin your Phone
After rebooting if you see the SUPER SU APP in your app drawer, you have successfully ROOTED your Phone.
BACKUP YOUR IMEI
First of all take backup of your imei for that you have to install 5iromtoolbox
1)Open the app
2)Press backup IMEI
3)Connect your phone with USB cable and go to your pc
4)Open your sd card through windows explorer or whatever you use
5)Seek the folder /sdcard/5irom/imeibackup/
6)Copy the imeibackup folder to your pc to a folder that you will not by accident format ^_^
7)You are ok...now you can make whatever you like...
To restore your IMEI
1)Take your imeibackup folder from your pc
2)Paste it on your sd card on folder /sdcard/5irom/imeibackup/
3)Open the 5iromtoolbox
4)Press Restore IMEI and restart your phone!!
INSTALLING CUSTOM RECOVERY[IN THIS TUT CLOCK WORK MOD]
Install MTK Drivers for your phone if officially available or else follow the steps bellow.
Installing Drivers for any android phone
First of all download Pdanet+
1) Enable USB Debugging in Settings -> Developer Options (If you dont have Developer Options in your settings tap 7 times the build number inside about phone, Then you will get the Developer Option)
2) Connect your Phone with a Data cable and run the Pdanet setup >> choose others and continue all the way
IF SETUP FAILS
1) Do it another time with other usb options available in your phone like changing to MTP, Camera(PTP), or by turning on the USB Storage, Do it several times it should install the Drivers
IF SETUP SUCCEEDS
1) Untick the ticked check-box and click finish.
Download MTK Droid Root & Tools developed by rua1(Senior Member at XDA)
1) Connect your phone to computer.
2) Run the tool
View attachment 2785013
View attachment 2785014
View attachment 2785015
3) Press Root.... Wait for few Secs
4) Go to Root, backup & Recovery
5) Select "To use boot from phone". and select Recovery and Boot
6) If asked for any permission select yes.
And at last the device will reboot into recovery if you were inside the recovery, you have successfully done your job

This is an expanded version of rua1 review in his site......

IMEI NVRAM Restore Tools

Hi all users of P780. I have here this tools that can be useful to you.
Link: HERE
Please post some messages with the tool worked for you, and how.
Pressing thanks button will be apreciated! :good:
How to and some explanations.
If your IMEI is not there you can check by going to: your phone settings - About phone - Status (general information) - Information on IMEI. If the IMEI is not there, it means NVRAM damaged.
Now lets see the tutorial:.
How to restore the NVRAM with Maui META 3G and SP META
Youtube Link here on this post: http://forum.xda-developers.com/unite-2/general/guide-repair-imei-invalid-micromax-t3048984
First 3 basic conditions
1. Make sure that you have really damaged NVRAM (the information is up).
2. Charge the smartphone. I recommend to charge it all the way to 100%.
3. Find and download the factory firmware for SP Flash Tool. There must be a base APBD and MODEMDB (usually in the folder of the same name, but rarely in the bulk folder target_bin). Skip this is you have it allready.
Creating a basic structure of NVRAM settings and recording IMEI.
1. Perform clearing the NVRAM or Formatting telephone (recommended) .
2. Remove and reinsert the battery. If this is not possible, after switching off the machine wait for 1 minute not less.
3. Install the drivers.
4. Flash STOCK Firmware.
5. Disconect the phone from PC.
6. AGAIN: Remove and reinsert the battery. If this is not possible, after switching off the machine wait for 1 minute not less.
7. Now with the phone powered off start with button pressed "Volume Down" and "Power" and keep up till the appearance of the logo. On the screen of your smartphone after the logo should appear on a black background "Have been in meta mode". TURN OFF THE PHONE.
8. WITH THE PHONE POWERED OFF connect to a standard computer "MicroUSB cable." In Device Manager, the equipment will appear: "CDC Serial" and "Lenovo XX". Using drivers SP_Drivers_EXE_v1.6.rar device "CDC Serial" to install the drivers "MediaTek Inc. -> MediaTek PreLoader USB VCOM (Android)", the unit "Lenovo XX" install drivers "Google, Inc. -> Android Composite ADB Interface"
9. Start MAUI META
10. In the menu: Actions - Open NVRAM Database. Select the file (usually begins at BPLGUInfoCustomAppSrcP ...) from my modemdb factory firmware for SP Flash Tool. For example for the A850 + file named BPLGUInfoCustomAppSrcP_MT6592_S00_A850 + _V1_1_wg_n and size 5,5MB for A606 file named LWD3I15.1.6.1.3T21A0828_M015.src and size 7.3Mb. The main thing that this file has been included with the firmware that is now on your phone. It is important!
11. Press Reconnect. Flashes circle from red to green.
12. AGAIN: Remove the battery and re-set. If this is not possible, after switching off the machine wait for 1 minute.
13. Turning off the machine connect to a standard computer "MicroUSB cable."
14. If the program is successfully connected to the phone to change the color of a circle of yellow and opens the selected option. ** Before connecting the program selection option is not available, so if it is not "Update parameter" just close the window that appears.
15. In the main window of the program Maui META 3G select "Update parameter"
16. In the "Update parameter" click "Load from file" and select the ini-file with the calibration. Base to restore NVRAM as possible will be augmented with such files.
17. Click Download to Flash
18. Wait until all the blue lettering turn gray, close the "Update parameter".
19. In the main window of the program Maui META 3G select "IMEI Download"
20. Enter in the field without the last of the IMEI numbers (it will be calculated automatically) and click "Download to flash"
21. Go to the second tab. Enter in the field without the last of the IMEI numbers (it will be calculated automatically) and click "Download to flash". If you can not find / remember what was the IMEI, then add to the penultimate figure 8, the checksum will be calculated automatically.
22. IMEI Download Close window and click Disconnect. Phone out of METAMODE and power off.
23. Reboot.
Record MAC-addresses of Bluetooth and Wi-Fi, as well as SN in NVRAM.
1. Start SP_META (Attention! The second program from the set). If the proposed version of the program is not connected to the phone, then we try to pick up a different version .
2. Select the option "AP NVRAM Editor".
3. Press Reconnect. Flashes circle from red to green.
4. Remove the battery and re-set. If this is not possible, after switching off the machine wait for 1 minute.
5. Turning off the machine connect to a standard computer "MicroUSB cable."
6. If the program is successfully connected to the phone screen appears "AP Editor".
7. In the "AP Editor" click "read from NVRAM". The program will ask you APDB. Select the file (usually begins at APDB _...) from my apdb factory firmware for SP Flash Tool. For example for the A850 + file named APDB_MT6592_S01_ALPS.JB9.MP_ and size 163Kb for A606 file named APDB_MT6582_S01_KK1.MP3_ and size 162Kb. The main thing that this file has been included with the firmware that is now on your phone. It is important!
Correction MAC for Bluetooth
1. In the left pane, open the tree: "RDEB LID -> AP_CFG_RDEB_FILE_ BT_ADDR _LID -> 1 "
2. Click "read from NVRAM".
3. In the right pane to open: "ap_nvram_btradio_mt6610_struct -> addr".
4. Fill 6 groups of elements. For example, to assign a MAC Address: 98: FF: DD: A1: 05: 06 must be:
in addr [0] to enter 0x98 (the first character of zero, then the Latin character "X"),
addr [1] - 0xFF,
addr [ 2] - 0xDD,
addr [3] - 0xa1,
addr [4] - 0x05,
addr [5] - 0x06.
5. In the left pane again highlight: "RDEB LID -> AP_CFG_RDEB_FILE_ BT_ADDR _LID -> 1 "
6. Press the "save to NVRAM"
7. Check that the bottom left of the window there was an inscription: "NVRAM write record successfully", and the right side red field addr [0] - addr [6] become black.
8. Click "Clear".
Correction MAC for WIFI
1. In the left pane, open the tree: "RDEB LID -> AP_CFG_RDEB_FILE_ WIFI _LID -> 1 "
2. Click "read from NVRAM".
3. In the right pane to open: "WIFI_CFG_PARAM_STRUCT -> aucMacAddress".
4. Fill 6 groups of elements. For example, to assign a MAC Address: 98: FF: DD: A2: 05: 06 must be:
in aucMacAddress [0] to enter 0x98 (the first character of zero, then the Latin character "X"),
aucMacAddress [1] - 0xFF,
aucMacAddress [ 2] - 0xDD,
aucMacAddress [3] - 0xa2,
aucMacAddress [4] - 0x05,
aucMacAddress [5] - 0x06.
5. In the left pane again highlight: "RDEB LID -> AP_CFG_RDEB_FILE_ WIFI _LID -> 1 "
6. Press the "save to NVRAM"
7. Check that the bottom left of the window there was an inscription: "NVRAM write record successfully", and the right side red field aucMacAddress [0] - aucMacAddress [6] become black.
8. Close window "AP Editor".
9. The "SP Meta Tool" click "Disconnect" and close the program.
How to format the phone ...
It is recommended to make mandatory before starting the recovery process NVRAM.
1. Download and Start SP_Flash_Tool_v5.
2. Charge your phone 100%.
3. Disconnect the device from the charger or PC
4. Turn off your phone.
5. Remove the battery and re-set. If this is not possible, after switching off the machine wait for 1 minute.
6. Turning off the machine connect to a standard computer "MicroUSB cable." In Device Manager, the equipment will appear: "MT65xx Preloader"
7. At this step you must install the drivers
8. Disconnect the device from the computer and set aside.
9. Start SP FlashTool 5.1352.01 , and load the scatter-file **.
10. Open tab Format, set the switch to "Auto Format Flash" and "Format whole flash except Bootloader"
11. Click the Start button in the program SP_Flash_Tool.
12. Connect the phone
13. The program will run SP_Flash_Tool red and green stripe, and the program will display a window with a green circle and a bird .
14. Disconnect the device from your computer.
SN WRITE TOOL TUTORIAL TESTED AND WORKING
The process is performed in two steps.
Step one
1. Install the drivers, CDC drivers must be installed manualy! NOT OPTIONAL!
2. After instalation of the drivers disconect the phone.
3. Download SP Flash Tool from here: https://drive.google.com/folderview?id=0B_B98oK4DpK1S1l2bXRkTGxhVFk&usp=sharing
4. To format the phone using SP FlashTool:
a) Choose scatter file from the factory firmware.
b) Click "Format" and choose the radio button "Format whole flash except Bootloader" and press OK. Wait until the operation is complete.
5. Flash the phone stock firmware from here: http://forum.xda-developers.com/lenovo-p780/development/p780-stock-rom-links-t2842399
Step two
1. After flashing stock firmware disconect the phone from PC or Notebook. Boot at least once.
2. In the google drive you have all the drivers you need in each folder for each tool.
3. Power down the phone. Start the phone by Holding pressed "Power" and "Volume down". The phone will boot in Metamode. The screen will display: "Have been in meta mode, long press the power button and the normal boot". In this state, connect the phone to PC and install drivers ADB and CDC Serial, which are given in drive.
4. After drivers instalation disconect the phone and keep him powered off for at least 1 minute.
5. Install and open SN WRITE TOOL
6. Load files under apdb, ap_modem_db_p780, modem_db
7. Now run the program SN WRITE TOOL and configure as in the screenshot.
8. Disconect the phone again and keep him powered off for at least 1 minute.
9. Press the Start button on SN WRITE TOOL. One window will appear with the option to write 2 IMEI`s option b from below.
a. In the first window you want to record the serial number of "Please scan SN", it looks something like this "are 0123456789abcdef" and press Enter;
b. In the second box IMEI Scaner" to write 2 IMEI and press OK;
c. In the third window, "Please scan SmartPhone BT adress" to enter the Bluetooth address, it looks like "80cf41750505" and press Enter;
d. In the fourth box, "Please scan Wifi MAC then ower On phone" to enter the address of Wi-Fi, it looks like "80cf41760606" and press Enter. (If after the prescription SN you have problems with communication and in the settings, when viewing information about IMEI error settings application, in the field of SN do not enter anything!)
10. Power on the phone in Meta Mode and connect the phone to PC. Wait for the Write Result Indicator to become from black to green. (When the line "Step: Meta Disconnect with target" may disconnect your phone and try again)
11. Disconect the phone and keep him powered off for at least 1 minute.
12. Turn on your phone and to check the efficiency of telephony, Bluetotth and Wi-Fi.
13. If you have NVRAM WARNING: Err = 0x10 error flash WIFI FIX from attached file.
14. Good Luck.

RESERVED FOR FUTURE INFORMATION

@stympy, man you are awesome. great work. thank you.

No one tested this tools?
No feedback here ?
Anyone ?

stympy said:
No one tested this tools?
No feedback here ?
Anyone ?
Click to expand...
Click to collapse
I tried to restore mac addr bluetooth and wifi, but no results. Bluetooth addres passed, wifi mac always was wrong (I wrote both them just after buing phone, but unfortunately I didn't make nvram backup) My phone lenovo p780 2014 (speed version). I tried to use many tools (probably all possible). Maybe I have wrong modemdb file? Installed rom is 226 (Kitkat), rooted, twrp. I tried to restore nvram.img (file from web)- no results.
Regards

gitbroda said:
I tried to restore mac addr bluetooth and wifi, but no results. Bluetooth addres passed, wifi mac always was wrong (I wrote both them just after buing phone, but unfortunately I didn't make nvram backup) My phone lenovo p780 2014 (speed version). I tried to use many tools (probably all possible). Maybe I have wrong modemdb file? Installed rom is 226 (Kitkat), rooted, twrp. I tried to restore nvram.img (file from web)- no results.
Regards
Click to expand...
Click to collapse
Thanks for your feedback! Did you tried stock JellyBean firmware?

Yes, but not every tool. I will try to flash 116 rom, i tried already few times with 228 preloader, but something was wrong. I'll try to use different preloader...

I flashed 136 rom (4.2.1)
I tried to restore everything (four in one)
result:
"OK: Connect to target successfully.
>>Step: Start to write Wifi MAC.
Error: Write Wifi MAC fail. Meta Result = META_INVALID_ARGUMENTS"
I don't know correct serial (I bought only mainboard and I forgot to write it down)
Maybe this is a reason?

gitbroda said:
I flashed 136 rom (4.2.1)
I tried to restore everything (four in one)
result:
"OK: Connect to target successfully.
>>Step: Start to write Wifi MAC.
Error: Write Wifi MAC fail. Meta Result = META_INVALID_ARGUMENTS"
I don't know correct serial (I bought only mainboard and I forgot to write it down)
Maybe this is a reason?
Click to expand...
Click to collapse
must be... it is possible!
did you tried one by one ?

maybe I wrote something wrong in MAC addr...?
>>Step: Scan Smart Phone Wifi MAC.
OK: Wifi MAC = "00082268bffb".
>>Step: Start to Connect with target.
COM port searching and Kernel handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
OK: Connect to target successfully.
>>Step: Start to write Wifi MAC.
Error: Write Wifi MAC fail. Meta Result = 10

gitbroda said:
maybe I wrote something wrong in MAC addr...?
>>Step: Scan Smart Phone Wifi MAC.
OK: Wifi MAC = "00082268bffb".
>>Step: Start to Connect with target.
COM port searching and Kernel handshake
COM port searching and preloader handshake ok
COM port searching and Kernel handshake
OK: Connect to target successfully.
>>Step: Start to write Wifi MAC.
Error: Write Wifi MAC fail. Meta Result = 10
Click to expand...
Click to collapse
try to write thisway: Wifi MAC = "00:08:22:68:bf:fb".
Iff thisdont work try this: https://www.youtube.com/watch?v=8ejnFB5i5o8
Tell me what is going on !

Thank You for Your help!
Anyway... it doesn't work
In Sn_station is possible only to write 12 digits, no one more
I tried to do this Youtube way, precisely copied files, changed permissions, doesn't work too
I lost both Mac addresses after rooting phone vroot aplication
Now system shows them just: "unavaible"
What is interesting, bluetooth addres passed sn_station, but bluetooth doesn't work anyway
Regards

gitbroda said:
Thank You for Your help!
Anyway... it doesn't work
In Sn_station is possible only to write 12 digits, no one more
I tried to do this Youtube way, precisely copied files, changed permissions, doesn't work too
I lost both Mac addresses after rooting phone vroot aplication
Now system shows them just: "unavaible"
What is interesting, bluetooth addres passed sn_station, but bluetooth doesn't work anyway
Regards
Click to expand...
Click to collapse
Hi. I have modified the tutorial nr. 2 and now iti is working. Tested.

stympy said:
Hi. I have modified the tutorial nr. 2 and now iti is working. Tested.
Click to expand...
Click to collapse
stympy i could not understood step 6 in SN write tool method.

bauuuuu said:
stympy i could not understood step 6 in SN write tool method.
Click to expand...
Click to collapse
In stock firmware, in the archive you will find 2 files. That are the files from step 6. Look in what i have posted on the google drive. There are the files.

stympy said:
In stock firmware, in the archive you will find 2 files. That are the files from step 6. Look in what i have posted on the google drive. There are the files.
Click to expand...
Click to collapse
All is good. I was missing the CDC driver installation. Now all OK

Hi @stympy
I restored my imei using sn write tool but i wrote imei 1 and 2 manually, automatically it didnt detect .
Anyway it fixed my imei problem .
I skipped BT address how to get BT address ??

kishanjith said:
Hi @stympy
I restored my imei using sn write tool but i wrote imei 1 and 2 manually, automatically it didnt detect .
Anyway it fixed my imei problem .
I skipped BT address how to get BT address ??
Click to expand...
Click to collapse
Dont understand!
This tool do not detect your IMEI!
You must write your IMEI in that boxes! Manualy!
When the green sesor appear it is done !

8. WITH THE PHONE POWERED OFF connect to a standard computer "MicroUSB cable." In Device Manager, the equipment will appear: "CDC Serial" and "Lenovo XX". Using drivers SP_Drivers_EXE_v1.6.rar device "CDC Serial" to install the drivers "MediaTek Inc. -> MediaTek PreLoader USB VCOM (Android)", the unit "Lenovo XX" install drivers "Google, Inc. -> Android Composite ADB Interface"
Click to expand...
Click to collapse
Download Driver_Auto_Installer_v1.1236.00_.7zip
SP_Drivers_EXE_v1.6.rar
But still cannt install CDC Serial Driver
use "SP_Drivers_EXE_v1.6\cdc-acm.inf " , computer prompt " You select inf file not support this install method“ . (In fact , computer give Chinese message , I translate
use "Driver_Auto_Installer_v1.1236.00\install.bat"， computer prompt ” System can not find the path specified ".
My computer os is win7 32bit . I use administrator account . P780 4G ,
If you know how to solve ， Please inform

. In the menu: Actions - Open NVRAM Database. Select the file (usually begins at BPLGUInfoCustomAppSrcP ...) from my modemdb factory firmware for SP Flash Tool. For example for the A850 + file named BPLGUInfoCustomAppSrcP_MT6592_S00_A850 + _V1_1_wg_n and size 5,5MB for A606 file named LWD3I15.1.6.1.3T21A0828_M015.src and size 7.3Mb. The main thing that this file has been included with the firmware that is now on your phone. It is important!
Click to expand...
Click to collapse
Open NVRAM Database , Meta2_3G prompt " Execution Failure : Initialize NVRAM database file."
I found "BPLGUInfoCustomAppSrcP_MT6589_S00_P780_V23 " in ap_modem_db_P780.7z and modemdb.7z and I try twice . Meta2_3G still prompt " Execution Failure : Initialize NVRAM database file."

Better Mobile App

welcome