[SOLVED] Flashed 5.11 BL... and stuck - Galaxy S6 Edge Q&A, Help & Troubleshooting

OK I screwed up. I would appreciate any help here. Rogers S6 Edge, G925W8. It was stock 5.0.2.
Wanted to try a ROM so flashed TWRP, then flashed Kingfisher ROM v1.1 (it seemed the safest / W8-friendly). ROM was fantastic (much better battery), but GPS would never lock.
Tried to start over by flashing stock Rogers 5.0.2 via Odin but it wouldn't flash. I read (a little too late) that downgrading isn't something Samsung enjoys. Argh!
Then out of desperation, I flashed the BL (BL_G925W8VLU2BOH8_5.1.1.tar) from http://forum.xda-developers.com/galaxy-s6-edge/general/canadian-odin-5-1-1-bootloader-twrp-t3196595 , which was a very bad move, I assume because I wasn't on 5.1.1 to begin with. Crap!!
So now the phone gets to the Galaxy S6 edge splash screen, with "KERNEL IS NOT SEANDROID ENFORCING", and it stays there. The phone also gets very warm, and I can't shut it off. Using VolDown+Power+Home reboots it (showing the same message) but doesn't shut it off. Using VolUp+Power+Home reboots it but only says the same thing about Recovery.
Please tell me that I didn't just brick this phone!!

UPDATE:
Am able to get the phone into Download/Odin mode by holding the 3 buttons (voldown+power+home) while plugging the phone into USB. The stock Rogers image refuses to flash (Odin says fail immediately), but I am a step closer thanks to @brar.arsh's thread ( http://forum.xda-developers.com/galaxy-s6-edge/general/canada-galaxy-s6-edge-canadian-users-t3069314 )
From there I grabbed the "S6 Edge Stock Firmware OG2" which comes in 4 parts (BL, AP, CP, and CSC). I added all 4 pieces to Odin and started flash. Boot.img and recovery flashed, but then during the system.img flash, it failed about half-way through. Right after that failure, something changed because the device now became "Unknown Device" to windows, and it complained that "a USB device has malfunctioned, and Windows no longer recognizes it".
This gave me hope that I could get into Recovery (since that flash was successful), but the phone likes to boot directly to the "The update failed so please launch Smart Switch" message - regardless of starting with VOLUP+PWR+HOME button combination. So no recovery access... but making progress.
I belive I initiated a flash that contained JUST the BL, CP, and CSC portions, and it passed quickly. This, of course, isn't enough to get the system going. I just wanted to see if it would fail in other areas.
Trying the emergency flash via Smart Switch: Smart Switch said it required the phone to be in Recovery mode, but it still attempted the fix even though I was in Odin/Download mode. Good news, but unfortunately it gave the same result - a failure at around 50% of the entire flash operation.
I have tried re-flashing the AP portion several times and it fails at different progressions (50%, 75%, 90%)... so close.
I was thinking that it was maybe a power issue (since the battery was completely dead during the "kernel is not seandroid enforcing" period, with no way to turn the phone off or pull battery), I wondered if the battery just needed a little juice before starting the operation. I let it stay plugged in for a few minutes after one of the many failed flash attempts (screen was illuminated with the progress bar frozen at the point of failure). I noticed that when I unplugged it, it didn't die immediately, so I plugged it back in (getting the "USB device has malfunctioned" message again), and forced it to restart by holding the VOLDOWN+PWR+HOME buttons). It got back into Odin mode and the PC recognized it again. Loaded up just the AP portion in Odin, hit Start, left the room, and when I came back it said PASS! I cannot prove that it had any battery power from this method... or if it even helped. This could have just been a fluke.
The phone automatically rebooted into Recovery mode (which scared me) so I hit Power Down.
Rebooted the phone - I hear the lame Samsung startup song, and it is booting. Hallelujah.

Related

[Q] Samsung S6500 problem

Hi everyone, I have this weird problem with my S6500, or rather my younger brother has.
He tried to put on his S6500 (not D, this phone is with NFC) Cyanogenmod 10.1, after some ups and downs, he finally got it to work, but... camera wasn't working, it was said on the cyanogenmod page to flash with the newest update, he did that, phone worked good... almost, after he was blocking his screen, he couldn't unlock it, because there was some kind of white screen stuff, weirder was the thing, that he could hear all the *clicking* sounds as he was trying to unlock. He had to restart the phone every time after he blocked the screen, so he wanted the phone to function normally and tried to put his stock ROM back again. Well the flashing went well (as Odin showed) but the phone stucked in bootloop.
The phone showed the Orange logo (he is using his original stock rom from Orange Poland, downloaded from sammymobile) and then it quickly changed to Samsung logo, after that the phone vibrates once, and after that it vibrates 3 times really fast and restarts from the Orange logo.
He tried to get into Recovery mode, but coul;dn't (the phone doesn't react to any of the combinations we found - vol+,vol-, home and power and many others), and as I forgot to mention before, after every flash (while the recovery was working) he cleared data in menu of the recovery.
We also tried the different method to boot the phone into recovery mode (put it in Download mode, which works and then instead of going further by pressing vol+ we pressed the down button and held vol+,vol- and home button, but instead of going into recovery the phone booted in weird screen with small letters RAMDUMP MODE (ARM9 mode).
We tried several times to flash new recovery with Odin, but it doesnt work, the PIT file also doesn't work, or can someone provide me with the stock s6500 PIT file as I couldn't find one, because I read in the Polish forum, that screen mentioned before only shows up if there is a SuperUser app in the phone, so we need the PIT file to flush it.
So the problem is after flashing it with numerous cwm and original stock roms we couldn't get it to boot or to get into recovery menu, or get it working.
Also the hardware is all ok, as the phone is almost brand-new ( he got it from the Orange few months ago).
So help plz?
I have the very SAME problem with my S6500D. Same as described above.
Anyone has managed to fix this problem ? I have all needed tools.

[Q] help me XDA, phone crashes during boot

I think I'm ****ed here, but maybe someone can help.
My s4 is still running the MDK boot loader, I was running the gpe 5.0 ROM, and all was well. I installed the xposed framework, and that seemed to be working fine. I was playing with my device in bed that night and it died on me. I assumed I had missed a battery warning and put it on the charger. None of the buttons are responsive. By removing and replacing the battery I couldn't get it to boot past the samsung/custom screen. I put it on the charger and woke to a phone call, phone was working fine for a few minutes, then the screen went black and I'm in the same position.
If I attempt to boot into fastboot (holding the correct buttons while inserting the battery) , the fastboot warning screen shows for a couple seconds and then goes black. If I attempt to boot into recovery the small blue text will show up in the top right then the screen goes black again.
Assuming I'm ****ed since I can't get into recovery or download mode for Odin. Anyone have any ideas?
Also... If I have to replace, droid turbo or nexus 6?
My daughter had an issue with her S4 that looks like it matches closely/exactly to your situation.
What i had to do to clear the issue up is as follows:
Download the correct Factory Image tar/md5 file OR If you backed up the original Image, locate that file.
Download the "Odin_v3.09" software.
Note: Not all the Odin software versions play well with all phones and the v3.09 always worked for me.
Place the phone in Download Mode.
Flash the correct Factory Image tar/md5 file (Select the tar/md5 file using the "AP" button).
Note: Be sure that the "Auto Reboot" and the "F. Reset Time" are the only Options Selected.
Now select "Start" and let Odin do it's magic.
Note: It is important that you NEVER interrupt the process!!!
Interrupting it can potentially do irreversible damage so before you press "Start", double check everything.
Once the Factory Image file was correctly uploaded, Odin will restart your phone.
This is what worked for me but always keep in mind that there are no guarantees it will work.
I really wish you luck!!!
It still shuts itself off when put in download mode, won't stay on long enough for me to do anything with Odin.
Just a thought... Try it without the battery in...
It sounds like a little water may have made it's way in the phone.
It takes only 1/2 a drop or less to create issues like arching power/signal, a little bit or more corrosion, etc...
Some phones also throw a fir or just die for no reason at no fault to the user...:crying:
I hope someone else on the forum can provide some additional options you can try.

Samsung Galaxy S4 WEIRD Problems (A must read for certified problem solvers)

Ok, so one night I was using my phone normally (Browsing. Watching YouTube, Playing Games) like everyone else does. Then all of a sudden it shuts off, but immediately turns on again without me pressing a button. (So basically it suddenly auto restarts on its own) This occured maybe 2-4 times (all in one night) until one time, it shuts off but doesn't turn on again (basically an automatic shutdown), so I tried turning it on again (Power button), then I got shocked because all of a sudden it enters a boot loop (Screen displaying this sequence : Samsung Galaxy S4 screen, my carrier logo screen, The encrypted screen (where you have to enter your encryption password) then again the Samsung logo but this time with the colors splashing from the background, then it shuts off again.) Sometimes after the boot loop sequence, it vibrates but never turns on again, sometimes it just turns off after the sequence. And as I try and try to get away from the boot loop, the sequence became shorter. So I'm guessing it's a battery problem, BUT my battery isn't bloated or deformed. I tried clearing the cache first, again the sequence got shorter (never going up to the carrier logo screen), then I tried formatting the data, still to no avail. Now, when I turn it on, It shows the Samsung logo screen for 2 seconds and shuts down.
I tried flashing it with ODIN thru Download mode BUT (HERE'S where another problem occured) :
My phone never get pass on the system.img.ext4 dialogue and my screen just goes blank. But ODIN still recognizes my phone. And when I remove the USB cable, ODIN says FAIL.
I'm sure the cable is working. I downloaded the firmware for my carrier (Tre 3).
What could be the real problem here?
Here is the description of my device :
Samsung Galaxy GT-I9505
Bought from Italy, Tre 3 carrier
Can I download a different region/carrier for my I9505 phone?
Advanced thanks for anyone who comments and I'm very sorry for my English. Thanks!
I would install TWRP recovery, boot to it, and use it to format data, which will remove the encryption. Then I would either push a rom to the phone via recovery or try to reinstall the stock firmware with Odin. Make sure that you run Odin as admin as well. The firmware must be the same version or newer. If you still have the stock recovery and can boot to it, then I think the build number of the currently installed firmware will be visible there. You should be able to use that to Google the correct version you need.
Hey it's me. Just posting a quick reply.
Thanks for replying to my post. Yesterday I successfully flash a rom to my GT-I9505 (Version 5.0.1 Italy HUI 3G). However it still didn't boot up. At first try it booted up to the first setup screen then just randomly shuts down. Then as I try to boot it up again, It just shuts down after the first Samsung logo (with the GT-I9505 logo), I can't boot into recovery cause it shuts down. I'm sure it's not a battery issue cause when I boot into download mode, it can stay in that screen for like 10 minutes. What could be the issue? I'm planning to disassemble my S4 sooner to see if something's wrong inside. Thanks again for the reply

Galaxy S6 Edge, does not boot up - only download mode possible

Hello dear users of xda.
I have read alot of threads on several forums to find a fix for my broken phone, since I am hoping that the problem is caused by the software, rather than the hardware.
Sadly I was not able to find the fix yet and therefor you guys are my last shot at this issue. This account is also freshly registered, so I will not be able to post any links or images to help you guys out understanding what happened ... so please just bear with me here
Since I am from Germany I hope you can also excuse small mistakes regarding my writing in this thread. Thank you in advance
Lets dive right into this with a few details:
Samsung Galaxy S6 Edge (SM-G925F)
Never rooted, flashed -> always official updates
Android 7 was up to date
Phone has no branding or any kind of simlock
What happened:
My phone was turned off a few days ago when I woke up. Since I always charge it over night it couldnt be out of power and that confused me.
I then pressed the On/Off-Button to start it and the phone booted up.
But the boot did get stuck on the Samung logo-animation. I mean the animation which is usually displayed after the big "Samsung Galaxy S6 Edge powered by Android".
I waited a minute or something and nothing happened, it seemed like the boot froze up and I turned it off.
When I booted it up again the samsung animation would not even finish and then freeze up. The animation is displaying the letters from left to right and it froze this time displaying only "Samsu".
After that I plugged the phone back into the wall to charge and went to the PC to google this issue. The phone displayed around 25% battery when I plugged it in.
So apparently it was not charging this night?
Anyways ... after googling and not finding any similiar problems I tryed to boot with Safe Mode ( holding Volume Down + On/Off Button .... no success) and then downloaded Samsung Switch and all drivers needed to get a device connected to the PC.
I connected the phone to the PC with an original Samsung cable and Samsung Switch was not showing anything until I entered the Download Mode on my phone by pressing Volume Down + Home + On/Off.
Then Samsung Switch displayed that the connected device was not compatible (even though it meets all requirements).
I went to the device manager to make sure that the drivers are working and the phone indeed was showing up in the list. It also disappeared properly when I unplugged it from the PC.
After that I again tryed out to boot the phone several times. It would always freeze up anywhere within that Samsung animation.
Not knowing what to do I thought an factory reset might help out and I pressed Volume Up + Home + On/Off for several seconds when the phone was turned off.
Nothing happened. I could only boot up the phone by pressing the On/Off button alone and by doing that it always froze up. Just the Download-Mode was accessable (Volume Down + Home + On/Off).
Since I had no way to recover or reset anything by using Samsung Switch or the Recovery Mode I decided to flash an official Samsung rom on the device using ODIN.
I downloaded the following:
Odin ( v3.12.3 )
Firmware ( G925FXXU5EQK8_G925FDBT5EQK1_G925FXXU5EQKF_HOME.tar.md5 // from a german android forum, information below )
FIRMWARE INFORMATION
Model: SM-G925F
Model name: Galaxy S6 edge
Country: Germany (DBT)
Version: Android 7.0
Changelist: 10958180
Build date: Thu, 09 Nov 2017 10:08:50
Android security patch level: 2017-11-01
Product code: DBT
PDA: G925FXXU5EQK8
CSC: G925FDBT5EQK1
When I connected the phone Odin was recognizing the device and I was able to flash the firmware successfully. Odin did not display any kind of errors.
After the flash the phone was still connected to the PC since I feared it would run out of power. I know that the first boot after a flash can take a while. Since the LED was flashing while the big "Samsung Galaxy S6 Edge" logo was displayed I thought it was doing something in the background. I kept it like this (big logo, LED flashing, plugged into the PC) for over an hour and nothing did change. The device was warm but I doubted that it's doing anything since one hour for a boot, even after flashing, is way too long.
After that hour I turned it off and it instantly started to boot up again, but this time and all the other times after that it kept getting stuck at the big logo. It did not proceed into the animation like before.
I tested if I could enter the Recovery Mode at this point but it still was only able to get into the Download Mode.
The only way to stop it from trying to boot now was to get into that Download Mode, else it would just keep looping around, but not turn off by its own.
Every now and then, instead of displaying the big logo, it showed a blue screen with a yellow warning sign and the android mascot laying on the ground with "No command" beneath it. If you want to see how it looks you can google images "android 7.0 no command" and look for the full blue screen pictures.
Googling this blue screen with no command said that it can be easily fixed by wiping the data/cache from your device. But as I said the recovery mode was not showing up when I pressed the buttons for it. So a friend of mine suggested using ADB or fastboot to wipe the cache / dalvik cache.
Using both (ADB + fastboot) the device was not detected. We made sure that the drivers were installed properly. There was and there still is no way to connect to the phone with these both tools. Sadly.
After the first try of using ADB/fastboot we decided that the issue might have been the firmware I downloaded in the beginning and we used SamFirm (v0.3.6) to download the newest firmware for my SM-G925F ( G925FXXU5EQK8_G925FDBT5EQK1_G925FXXU5EQKF_HOME.tar.md5 )
This firmware appears to be the same as the one I downloaded before, but this one was slightly bigger.
This is a paste of the SamFirm window:
Checking firmware for SM-G925F/DBT/G925FXXU5EQK8/G925FDBT5EQK1/G925FXXU5EQKF/G925FXXU5EQK8
Model: SM-G925F
Version: G925FXXU5EQK8/G925FDBT5EQK1/G925FXXU5EQKF/G925FXXU5EQK8
OS: Nougat(Android 7.0)
Filename: SM-G925F_1_20171129140113_g7auy18e0c.zip.enc4
Size: 1950442496 bytes
LogicValue: 8ikzg48ul7hryauq
The flash was again successfull and still the same problem remained: no full boot.... sometimes a blue no command mascot.
After that we flashed again but with another PIT file attached. At first we got an error after the hidden.img but after changing the PIT file to this one ( ZEROLTE_EUR_OPEN_HIDDEN300M ) it worked again without any errors displayed by Odin. Apparently the PIT file we used at first did not have enough space for our hidden.img ...
We flashed that firmware several times and sometimes after the flash there would be a blue screen with an android mascot saying it is erasing, but the animation of that mascot freezes also after 10 to 20 seconds. I've kept the phone in this blue screen for several hours (up to 5h I think) since a few forum threads said that it sometimes takes very long to work and the LED was actually flashing all the time, but nothing changed.
We did not try to flash anything else because the Reactivation Lock is enabled and I have no idea how to turn this thing off w/o booting the device.
I would not mind flashing a custom firmware on the device as long as it just works again. So if this is somehow possible and might be a solution I am up for it.
What currenctly is going on with the phone:
· It only turns completly off when the power runs out.
· No button combination is working to turn it off.
· I can enter Download Mode easily but I can not enter the Factory Reset Mode.
Within the Download Mode it says:
ODIN MODE
Product Name: SM-G925F
Current Binary: Samsung Official
System Status: Official
Reactivation Lock: On
Secure Download: Enabled
KNOX Warranty Void: 0 (0x0000)
RP SWREV: B:5 K:2 S:2
· The boot ends either up with showing an "Samsung Galaxy S6 Edge powered by Android" logo for the whole time (kept it like that for several hours, no boot)
· or with a blue screen (yellow warning sign, android mascot laying on the ground and a "no command" beneath it).
· Odin is recognizing it as a device.
· The device manager is recognizing the device.
· Samsung Switch is saying the device is not compatible.
· ADB/fastboot can not detect the device.
So ... is it possible to get this damn thing to work again or is it gone for good?
If you still got any questions regarding the current state of the phone please ask. I will try to reply ASAP.
Thank you very much for any reply you guys might throw at me.
It sounds like a hardware fault and your phone is kaput.
Interesting.I would love to open the phone to inspect it
FaKeT said:
Hello dear users of xda.
I have read alot of threads on several forums to find a fix for my broken phone, since I am hoping that the problem is caused by the software, rather than the hardware.
Sadly I was not able to find the fix yet and therefor you guys are my last shot at this issue. This account is also freshly registered, so I will not be able to post any links or images to help you guys out understanding what happened ... so please just bear with me here
Since I am from Germany I hope you can also excuse small mistakes regarding my writing in this thread. Thank you in advance
Lets dive right into this with a few details:
Samsung Galaxy S6 Edge (SM-G925F)
Never rooted, flashed -> always official updates
Android 7 was up to date
Phone has no branding or any kind of simlock
What happened:
My phone was turned off a few days ago when I woke up. Since I always charge it over night it couldnt be out of power and that confused me.
I then pressed the On/Off-Button to start it and the phone booted up.
But the boot did get stuck on the Samung logo-animation. I mean the animation which is usually displayed after the big "Samsung Galaxy S6 Edge powered by Android".
I waited a minute or something and nothing happened, it seemed like the boot froze up and I turned it off.
When I booted it up again the samsung animation would not even finish and then freeze up. The animation is displaying the letters from left to right and it froze this time displaying only "Samsu".
After that I plugged the phone back into the wall to charge and went to the PC to google this issue. The phone displayed around 25% battery when I plugged it in.
So apparently it was not charging this night?
Anyways ... after googling and not finding any similiar problems I tryed to boot with Safe Mode ( holding Volume Down + On/Off Button .... no success) and then downloaded Samsung Switch and all drivers needed to get a device connected to the PC.
I connected the phone to the PC with an original Samsung cable and Samsung Switch was not showing anything until I entered the Download Mode on my phone by pressing Volume Down + Home + On/Off.
Then Samsung Switch displayed that the connected device was not compatible (even though it meets all requirements).
I went to the device manager to make sure that the drivers are working and the phone indeed was showing up in the list. It also disappeared properly when I unplugged it from the PC.
After that I again tryed out to boot the phone several times. It would always freeze up anywhere within that Samsung animation.
Not knowing what to do I thought an factory reset might help out and I pressed Volume Up + Home + On/Off for several seconds when the phone was turned off.
Nothing happened. I could only boot up the phone by pressing the On/Off button alone and by doing that it always froze up. Just the Download-Mode was accessable (Volume Down + Home + On/Off).
Since I had no way to recover or reset anything by using Samsung Switch or the Recovery Mode I decided to flash an official Samsung rom on the device using ODIN.
I downloaded the following:
Odin ( v3.12.3 )
Firmware ( G925FXXU5EQK8_G925FDBT5EQK1_G925FXXU5EQKF_HOME.tar.md5 // from a german android forum, information below )
FIRMWARE INFORMATION
Model: SM-G925F
Model name: Galaxy S6 edge
Country: Germany (DBT)
Version: Android 7.0
Changelist: 10958180
Build date: Thu, 09 Nov 2017 10:08:50
Android security patch level: 2017-11-01
Product code: DBT
PDA: G925FXXU5EQK8
CSC: G925FDBT5EQK1
When I connected the phone Odin was recognizing the device and I was able to flash the firmware successfully. Odin did not display any kind of errors.
After the flash the phone was still connected to the PC since I feared it would run out of power. I know that the first boot after a flash can take a while. Since the LED was flashing while the big "Samsung Galaxy S6 Edge" logo was displayed I thought it was doing something in the background. I kept it like this (big logo, LED flashing, plugged into the PC) for over an hour and nothing did change. The device was warm but I doubted that it's doing anything since one hour for a boot, even after flashing, is way too long.
After that hour I turned it off and it instantly started to boot up again, but this time and all the other times after that it kept getting stuck at the big logo. It did not proceed into the animation like before.
I tested if I could enter the Recovery Mode at this point but it still was only able to get into the Download Mode.
The only way to stop it from trying to boot now was to get into that Download Mode, else it would just keep looping around, but not turn off by its own.
Every now and then, instead of displaying the big logo, it showed a blue screen with a yellow warning sign and the android mascot laying on the ground with "No command" beneath it. If you want to see how it looks you can google images "android 7.0 no command" and look for the full blue screen pictures.
Googling this blue screen with no command said that it can be easily fixed by wiping the data/cache from your device. But as I said the recovery mode was not showing up when I pressed the buttons for it. So a friend of mine suggested using ADB or fastboot to wipe the cache / dalvik cache.
Using both (ADB + fastboot) the device was not detected. We made sure that the drivers were installed properly. There was and there still is no way to connect to the phone with these both tools. Sadly.
After the first try of using ADB/fastboot we decided that the issue might have been the firmware I downloaded in the beginning and we used SamFirm (v0.3.6) to download the newest firmware for my SM-G925F ( G925FXXU5EQK8_G925FDBT5EQK1_G925FXXU5EQKF_HOME.tar.md5 )
This firmware appears to be the same as the one I downloaded before, but this one was slightly bigger.
This is a paste of the SamFirm window:
Checking firmware for SM-G925F/DBT/G925FXXU5EQK8/G925FDBT5EQK1/G925FXXU5EQKF/G925FXXU5EQK8
Model: SM-G925F
Version: G925FXXU5EQK8/G925FDBT5EQK1/G925FXXU5EQKF/G925FXXU5EQK8
OS: Nougat(Android 7.0)
Filename: SM-G925F_1_20171129140113_g7auy18e0c.zip.enc4
Size: 1950442496 bytes
LogicValue: 8ikzg48ul7hryauq
The flash was again successfull and still the same problem remained: no full boot.... sometimes a blue no command mascot.
After that we flashed again but with another PIT file attached. At first we got an error after the hidden.img but after changing the PIT file to this one ( ZEROLTE_EUR_OPEN_HIDDEN300M ) it worked again without any errors displayed by Odin. Apparently the PIT file we used at first did not have enough space for our hidden.img ...
We flashed that firmware several times and sometimes after the flash there would be a blue screen with an android mascot saying it is erasing, but the animation of that mascot freezes also after 10 to 20 seconds. I've kept the phone in this blue screen for several hours (up to 5h I think) since a few forum threads said that it sometimes takes very long to work and the LED was actually flashing all the time, but nothing changed.
We did not try to flash anything else because the Reactivation Lock is enabled and I have no idea how to turn this thing off w/o booting the device.
I would not mind flashing a custom firmware on the device as long as it just works again. So if this is somehow possible and might be a solution I am up for it.
What currenctly is going on with the phone:
· It only turns completly off when the power runs out.
· No button combination is working to turn it off.
· I can enter Download Mode easily but I can not enter the Factory Reset Mode.
Within the Download Mode it says:
ODIN MODE
Product Name: SM-G925F
Current Binary: Samsung Official
System Status: Official
Reactivation Lock: On
Secure Download: Enabled
KNOX Warranty Void: 0 (0x0000)
RP SWREV: B:5 K:2 S:2
· The boot ends either up with showing an "Samsung Galaxy S6 Edge powered by Android" logo for the whole time (kept it like that for several hours, no boot)
· or with a blue screen (yellow warning sign, android mascot laying on the ground and a "no command" beneath it).
· Odin is recognizing it as a device.
· The device manager is recognizing the device.
· Samsung Switch is saying the device is not compatible.
· ADB/fastboot can not detect the device.
So ... is it possible to get this damn thing to work again or is it gone for good?
If you still got any questions regarding the current state of the phone please ask. I will try to reply ASAP.
Thank you very much for any reply you guys might throw at me.
Click to expand...
Click to collapse
If your not bothered about tripping knox (0x1) and voiding your warranty you can flash twrp recovery. Then wipe from there or flash a custom ROM. This way we can know for sure if it's software or hardware issue.
callumbr1 said:
If your not bothered about tripping knox (0x1) and voiding your warranty you can flash twrp recovery. Then wipe from there or flash a custom ROM. This way we can know for sure if it's software or hardware issue.
Click to expand...
Click to collapse
Thanks for that reply.
Sadly I can not flash twrp recovery because of that Reactivation Lock ... and I do not know how to deactivate it at the current state of the phone
Is there a way to workaround that lock?
same here lol. but even twrp recovery cannot run LOl, sammy charged me as U$$ 700 to repair,
of course i did not let them repair, and now i have a dead phone, that only goes to download mode, and the bootlogo with glitches
What if you get a stock ROM and flash it via Odin, if your phone goes to Download Mode...? I didnt totally understand your situation but that came to my mind, flashing stock firmware via Odin.
EDIT: Just went through your SITUATION a bit, you should get it inspected by someone and then decide, otherwise you might lose your phone permanently.
Same here
Same here.... But with s6....
Only download mode. Not even a bootlogo. No recovery... Tried flashing literally everything. is it possible to flash a custom Rom with Odin? Convert a rom.zip t a tar file? I tried flashing cf-root but I don't know if it's rooted...

samsung sm-g960u problems with NAND?

i have a samsung sm-g960u, that is locked to Sprint. On attempt to network unlock it by flashing the CP, it decided to never boot into the OS again. To clarify, when it was done flashing (with latest Odin), it reset, and made it to the blue screen with the Android icon, and the spinning arrows that says "Updating system software" and it will stay that way until the battery runs out. Upon using the Volume down and Pwr button reset, instead of taking me to Maintenance Mode, it goes to the black Factory Reset screen. Rebooting, Shutting Down, and rebooting into Download mode, all result in the phone being locked at this screen. I still have Download mode if im quick enoough to hit it after i power cycle it, and ive flashed the stock software successfully ( Odin says anyway) multiple times, with this same result. My question is this: Is this fixable through using the Nand Erase option in Odin? Also in the logs, i noticed it had some lines about the kernal being experimental(?) and to not use it, so im wondering when i flashed that CP modem file, if it somehow re wrote this version kernel into the phone? Im completely at a standstill here and any help would be great, as the phone is completely unusable at this point.

Categories

Resources