How to fix Acer Liquid E2 after flashing the wrong Preloader? - Android Q&A, Help & Troubleshooting

Hi..
I Have a problem with my Acer Liquid E2 Dual Sim..
Before this, my problem is the phone was stuck in the Ace green logo (Bootloop) and i tried to flash it using SP flash tool, and it flashed succesful until the green circle, but my device gotten even worse, now when i turn on the power, it just vibrate once and continue in blank screen only..and when i try to connect it to the pc, it recognize with a vibrate and blue led turning on, but in the device manager, it detects as MTK USB Port, the is no MTK Preloader or any driver except the mtk usb port
I already googled it, and it seems because i flashed the wrong preloader (it means i used the wrong firmware in the spflashtool), but i downloaded it from the global acer download, And another information i get that my device is in a condition where it enters the low-layer download interface of the MT65xx device (AFAIK).. Thats why it only detects as MTK USB Port. So what to do now? I have tried using SPFlashTool to Dwonload only the preloader checked using from two different rom, but no success both? already tried any different version spflashtool
Every time i tried to download the preloader to the device using spflashtool it just shows "dram failed"
like this
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!"
Does anyone knows how to fix it

Anyboy can help me pleaasee

lukerodriguez said:
Anyboy can help me pleaasee
Click to expand...
Click to collapse
i have same problem bro, is your phone already fix?

Related

MT6577 preloader recovery

Hi
I flashed the phone with invalid firmware using SP_Flash_Tool.
Now SP_Flash_Tool and Windows doesn't see the MT65xx Preloader USB device after disconnecting/reconnecting the battery.
The phone doesn't switch on.
Is possible to recover a preloader on MTK6577 (Zopo ZP 900) using the flex cables or other methods?
Thank you
I have same situation. Did you find any solution for this?
Hi all,
I accidentlly wipe preloader on my Lenovo P770 and computer identify it as "alcatel single rndis interface #2". Is there any possibility to restore preloader in my phone or it is comlete brick?
I would be very thankful for any help.
Lenovo P770 preloader wiped
my preloader accidentally wiped by my son, now my prealoder appears as ALCATEL.
I can't turn on my phone. Any ideas what to do?
when i install MTK Preloader / Usb driver, when i put the phone and usb on the computer it will disconnect after a few seconds, and connect and disconnects again.
The problem also appearing when i am flashing the phone with FLASHTOOL. That's why i am not able to flash my phone...
Kindly please help me out...
Any idea to help me regarding this problem would be a great help...
Thanks in advance...
Hi there...I am also facing the same problem in my mtk device...I could flash the stock rom from SP flashtool...but after flashing my phone is in dead state...Any Leads..???
I got to the same problem with my phone. There is no chance to turn it on.
Someone has got a suggestion?
Same problem.
We hope that one hero appears here
i will pay for the solution!
MTK6577 Tablet
Hey guys .. any solution ?
Lenovo A2107A-H, Dual SIM dead after SP-Flash
I stand in a row with you all, I also have killed my tablet with SP-Flash, It appears as Alcatel Single RNDIS Interface in Win7 control panel's network adaptors and in Win8.1 as "unknown device". I already uninstalled the drivers, the Win7 needed to reboot after that, but re-installed the same sh** after reconnecting. I have heard about another tool, not SP-Flash, which shall be able to "find" the tablet on the USB bus, but I don't remember the name.
How to un-brick Lenovo P770!
lystor said:
Hi
I flashed the phone with invalid firmware using SP_Flash_Tool.
Now SP_Flash_Tool and Windows doesn't see the MT65xx Preloader USB device after disconnecting/reconnecting the battery.
The phone doesn't switch on.
Is possible to recover a preloader on MTK6577 (Zopo ZP 900) using the flex cables or other methods?
Thank you
Click to expand...
Click to collapse
I un-bricked my Lenovo P770 yesterday!
How to do this:
1) Download and install "MT6577 USB VCOM drivers" -drivers for your phone
2) Open Device manager in your computer. Then "View" and "Show hidden devices" (do not close Device manager)
3) connect your phone to PC by USB cable (without battery, some phone with battery)
4) In device manager, in Network adapter (in my situation, after few second) shows "Alcatel single rndis interface #. . ." - it can appears and disappears!
5) When "Alcatel single rndis interface #. . ." appears click on this device Update drivers->Browse my computer...->Let me pick.. and here you should see "Mt65xx Preloader" if not you should find your driver.
6) When you update this driver you could use Flashtool v3->loading scatter file (you can find your android on needrom website. for example: P770_ROW_S110_130204_707WOW) -> check only PRELOADER and click Download
then connect your phone again to USB (without or with battery) and wait some seconds.
GoodLuck!!!
You can control on needrom website
I have the same issue. mediatek S8 - mt6577 7inch tab

Clone N2 brick after ROM update

Hi Masters,
I just like to inquire if I can still unbrick my clone Note phone. It has same spec as the HDC 5.7 Lord N9588 same box with NeoI brand. The main reason I flashed the ROM is because the accelerometer and GPS is not working so I found this ROM in needrom.com under HDC Lord N9588. as instruction says do not change anything in the setting (includes preloader). It successfully flashed the ROM but after reboot, the display is messed up and showing different color vertical lines. same as in the recovery. I believe that the phone still boots up, only the display messd up as I still can hear a sound every time I press the button and the screen and can hear volume sound when pressed. I still have the original ROM but the problem is it does not connect to SP flash. Last time when I connect to SP flash I can see MTK PReload VCOM USB when connected, now I can only see Preloader VCOM USB and gives errorS_COM PORT OPEN FAIL ERROR (1013) .already tried reinstall usb drivers.I can still access the phone trough adb shell but could not flash using fastboot at it says device not detected.
Thanks for any advice in advance.
Regards,
Ferdie

Help !! to unbrick NEO N003 MTK6589T error SP flash Error 4032 (Enable DRAM FAILED)

Hello please help i have a big problem on my NEO N003 1/4g T13
I have flashed to newest Stock room from the website neo then i try magerto room he was fine as the beginning then after 2 days he start freezing and sometimes working then the camera is no longer working i tell my self its just poor room
i decide to use the stock room but after i flashed work normal for 10 minute then freeze the screen turn black utile you remove the battery and put back in 2 minutes
after many times trying to flash it by sp flash tool i hit format ...my imei is gone and no signal on the sim card ( thats not a big problem)
but the phone still freezing and restarting ...black screen ......
after that the phone not able to turn on even the logo just black you can see he is trying turn on but no logo no nothing
in the device manager detect MediaTek Usb port before was detect preloader MediaTek somthing ......
look at the picture and the sp tool not working MediaTek Usb port and i got this error (look at the picture)
please help me i use the phone only 1 month please help me
this Morning accidentally i put the phone into Preloader Mode and make normal flash and my phone is a live a was very Happy i went to write the imei must root the phone...i have install root programe name is geno (he is work fine on lenovo P780) but in neo N003 he just freeze and tun off and no longer can trun it on again just black screen.
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Please Help Help !!!!!
Help me For God Sake I am going Crazy !!!!!
benladen said:
Hello please help i have a big problem on my NEO N003 1/4g T13
I have flashed to newest Stock room from the website neo then i try magerto room he was fine as the beginning then after 2 days he start freezing and sometimes working then the camera is no longer working i tell my self its just poor room
i decide to use the stock room but after i flashed work normal for 10 minute then freeze the screen turn black utile you remove the battery and put back in 2 minutes
after many times trying to flash it by sp flash tool i hit format ...my imei is gone and no signal on the sim card ( thats not a big problem)
but the phone still freezing and restarting ...black screen ......
after that the phone not able to turn on even the logo just black you can see he is trying turn on but no logo no nothing
in the device manager detect MediaTek Usb port before was detect preloader MediaTek somthing ......
look at the picture and the sp tool not working MediaTek Usb port and i got this error (look at the picture)
please help me i use the phone only 1 month please help me
this Morning accidentally i put the phone into Preloader Mode and make normal flash and my phone is a live a was very Happy i went to write the imei must root the phone...i have install root programe name is geno (he is work fine on lenovo P780) but in neo N003 he just freeze and tun off and no longer can trun it on again just black screen.
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Click to expand...
Click to collapse
benladen said:
Help me For God Sake I am going Crazy !!!!!
Click to expand...
Click to collapse
Why no one try to Help me please
:crying::crying::crying::crying::crying::crying::crying::crying::crying::crying:
Up up up
help !!!!​
benladen said:
Up up up
help !!!!​
Click to expand...
Click to collapse
help
benladen said:
Now when i plug the phone via usb port windows detect it MediaTek USB Port how i can put it again in Mediatek Preloader VCOM ???
Always get error 4032 on sp flash tool (format , upgrade, download) all he same error
Guys please Help me .
Click to expand...
Click to collapse
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
you help me a lot man !!!!!
oscarblue48 said:
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
Click to expand...
Click to collapse
Thank you so much man you help me a lot !!!
This how i get preloader
1-remove the battery
2-connect the phone to usb but before windows detect the device put the battery back
windows will detect preloder driver !!that's great
Now must go to my office i have windows 7 there to flash the phone with stock room and i will put the result later here
because i have win8.1 at home i get a lot of problem flashing this phone on it .
thank's again Peace.
oscarblue48 said:
On my phone, mine has the same chip as yours, to flash in preloader mode, I do it in this order,
1 connect phone to pc via usb with battery removed,
2 load flashtool with scatterfile and rom to flash,
3 click on download in flashtool,
4 put battery into phone
SPflashtool then searches for the preloader driver, loads it briefly and then loads the DA Usb Vcom port driver and then proceeds with flashing
This will only work if you have the usb vcom preloader drivers installed on your pc
To check if you have preloader driver installed, open device manager on your pc, connect your phone with usb cable and battery removed, put in battery while watching device manager, if driver is installed you should see 'Preloader Usb Vcom port' appear in the ports section,
but it will only be there for a few seconds, and will dissappear again. If you do not see this you need to install the Vcom driver.
Hope this helps
Click to expand...
Click to collapse
Hello, I can't Flash the phone over the preloder i have try 2 pcs and 2 diffrent drivers no luck the sp tool give me errors 4010... 2020
after trying many times i got flashed over the mediatek usb port ....
then the usb disconnect and the MediaTek DA USB VCOM connect and the flash begin utill 100%
but the phone not starting just black screen
try to format , upgrade , download nothing try 23 stock roms the old and the new nothing
please help help !!!
Do you see the preloader driver in device manager when you connect your phone as I described above?
Which build of SPflashtool are you using? the tool is quite buggy and sometimes helps to try another version
oscarblue48 said:
Do you see the preloader driver in device manager when you connect your phone as I described above?
Which build of SPflashtool are you using? the tool is quite buggy and sometimes helps to try another version
Click to expand...
Click to collapse
I don't see preloader driver i see just mediatek usb port
I am using SP Flash Tool v3.1328.0.183 and other versions
Now the flash not working again stop at the red bar 100% and give error 4032
i am sick with that error
i read some people get they phones alive with an loading an other preloader and the flash get throw !!!
look at this
thank you for responding man.
any One what i can do now ??!!!
Help for god sake !!
Ok, i think the only way your going to unbrick your phone is to flash the exact correct rom for it, Do you have a copy of the stock rom for your phone suitable for SPflashtool?
The link that you show is for a Feiteng H9500, that is very unlikely that it will work on your phone, the reason your phone is bricked is because you have probably flashed the wrong preloader block, and that is whats causing the trouble, you need to make sure you have the correct rom for your device before you start.
I think the only time you had a little success is when you accidentally entered preloader mode and if it were my phone I would concentrate on getting the preloader driver installed. There are some tutorials on here to install the drivers, it can be a bit tricky, and not all mediatek devices are the same, so a bit of trial and error may be needed
Once you have the Preloader usb vcom drivers installed I would then attempt to flash just the preloader and dsp_bl blocks initially from the correct rom for your phone, and then if successful flash the remainder of the rom, without preloader and dsp_bl
If you flash the wrong preloader/dsp_bl you will almost certainly brick your phone, so it must be either from a backup you have made of your original rom or from the exact stock rom for your phone.
oscarblue48 said:
Ok, i think the only way your going to unbrick your phone is to flash the exact correct rom for it, Do you have a copy of the stock rom for your phone suitable for SPflashtool?
The link that you show is for a Feiteng H9500, that is very unlikely that it will work on your phone, the reason your phone is bricked is because you have probably flashed the wrong preloader block, and that is whats causing the trouble, you need to make sure you have the correct rom for your device before you start.
I think the only time you had a little success is when you accidentally entered preloader mode and if it were my phone I would concentrate on getting the preloader driver installed. There are some tutorials on here to install the drivers, it can be a bit tricky, and not all mediatek devices are the same, so a bit of trial and error may be needed
Once you have the Preloader usb vcom drivers installed I would then attempt to flash just the preloader and dsp_bl blocks initially from the correct rom for your phone, and then if successful flash the remainder of the rom, without preloader and dsp_bl
If you flash the wrong preloader/dsp_bl you will almost certainly brick your phone, so it must be either from a backup you have made of your original rom or from the exact stock rom for your phone.
Click to expand...
Click to collapse
Thank you for you respond ,
i have Preloader usb vcom inslalled on my PC i have 3x stock roms from the NEO website all does not working always red bar 100% and get error 4032 on SP flash tool
Do you want to say that i will contact someone have the same model of my phone and tell him to make backup to his phone and upload it for me ? is it right ?
i have lenovo P780 when i turn it off and plug it to usb he detect it preloader mediatek then Disappears , thats what the NEO N003 must be :crying:
any way if some one have a rom work with my phone plz upload it for me
thank you again peace.
benladen said:
Thank you for you respond ,
i have Preloader usb vcom inslalled on my PC i have 3x stock roms from the NEO website all does not working always red bar 100% and get error 4032 on SP flash tool
Do you want to say that i will contact someone have the same model of my phone and tell him to make backup to his phone and upload it for me ? is it right ?
i have lenovo P780 when i turn it off and plug it to usb he detect it preloader mediatek then Disappears , thats what the NEO N003 must be :crying:
any way if some one have a rom work with my phone plz upload it for me
thank you again peace.
Click to expand...
Click to collapse
So the preloader vcom driver is installed ok on your pc, but you do not see it when you connect your phone, maybe you need to connect in a different way, on my phone I have to connect switched off phone with the battery removed, and when the battery is put in, then you see preloader driver pop up in device manager, there are many different MTK phones and different ways to connect.
The stock rom you have should be fine as long as it is the correct one for your device.
oscarblue48 said:
So the preloader vcom driver is installed ok on your pc, but you do not see it when you connect your phone, maybe you need to connect in a different way, on my phone I have to connect switched off phone with the battery removed, and when the battery is put in, then you see preloader driver pop up in device manager, there are many different MTK phones and different ways to connect.
The stock ROM you have should be fine as long as it is the correct one for your device.
Click to expand...
Click to collapse
the phone does not start at all not logo no no nothing is just black screen i have try this before connect the device then put the battery on it when it connect it's work first time the preloader device show , but i can not flash the ROM with it the sp flash tool give me error
i was able the flash it with mediatek usb port but the phone does not start black screen
, now i can't enter to the preloader device or even flash it with mediatek usb port !!!!!
yes its correct ROM i flash the phone with it before ...i brick the phone by root it by software name GENO the phone just stop working
i have use all the combination button but not luck i am stuck at mediatek usb port and sp tool give me error 4032....
:crying::crying::crying:
benladen said:
the phone does not start at all not logo no no nothing is just black screen i have try this before connect the device then put the battery on it when it connect it's work first time the preloader device show , but i can not flash the ROM with it the sp flash tool give me error
i was able the flash it with mediatek usb port but the phone does not start black screen
, now i can't enter to the preloader device or even flash it with mediatek usb port !!!!!
yes its correct ROM i flash the phone with it before ...i brick the phone by root it by software name GENO the phone just stop working
i have use all the combination button but not luck i am stuck at mediatek usb port and sp tool give me error 4032....
:crying::crying::crying:
Click to expand...
Click to collapse
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
oscarblue48 said:
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
Click to expand...
Click to collapse
ok thank you i will see what i can do !!
oscarblue48 said:
If your phone now is completely dead, probably your only hope of reviving it is by using the test point, see 'Modes of the virtual COM ports', here.....
http://forum.xda-developers.com/showpost.php?p=38369102&postcount=11
Ive never done this procedure, so cant help much with it, but if you search these threads for mediatek test point or similar, you might find some info on it
Click to expand...
Click to collapse
Hello, man can you Help me to find Test point
look at the picture down here
thank you.
benladen said:
Hello, man can you Help me to find Test point
Click to expand...
Click to collapse
As I said, Ive never done this myself, only read about it and have no idea where the test point is on your phone, they all appear to be in different places, on an mt6577 I had previously it was easy to find, just by the sim slot, there was no need to even strip the phone down, but on most other models they all seem to be less accessible. It will be somewhere on the main board I would imagine, usually, but not always, a small round brass dot about 2mm accross, and I noticed while searching that some are marked 'KCOLO' or similar. I believe also from what I've read that the manufacturers use this method to input the factory rom, so it must be there somewhere, its just a question of locating it. The best method to find it apparently is by testing different points with a multimeter to find one that corresponds with your battery output.
some more info here... http://forum.xda-developers.com/showpost.php?p=32424838&postcount=616
and a link to rua1's russian thread on the subject, translation with google chrome is not very good but there are some pics throughout the thread that might be helpful.... http://forum.china-iphone.ru/test-pointi-dlya-proshivki-preloader-na-mt6573-75-77-t22559.html

[Q] Lenovo P780 Briced Tool DL image fail

Hallo
I have problem with Lenovo P780 from 2013y.
After I broken my first (orginal) motherboard I decided to buy softbriced motherboard on local marked for 1 $ and try to fix it.
This motherboard arived to me with symtomps:
- after turn on -> charging logo only and red led
I tried to load ROM but I had a lot of problems with MTK drivers (I had error in SPflash: "Sp_flash tool error (4001). I read a lot of threads from this forum and found a lot of solutions (from Stympy user etc). I found MTK Driver Gooooooddddd or somethink and I can start to flash my lenovo but I forgot to set "DL DA Check Sum" After finish of flash I get green circle.
But after this lenovo start to bootloop with "TOOL DL image fail" and still reset after few seconds till I put red "reset" button.
When I connect it to laptop - I see MTK Preloader Drived in Device Manager for few second and disappears. I can't start flash it again because I get messege "Flash Tooll Error 4001"
I tried a lot of SPtool version, Rom version and MTK Driver versions - still the same error after click Firmware->Upgrate and connect phone to usb
Can somebody try to find solution? Thx
mielczareklukasz.poczta said:
Hallo
I have problem with Lenovo P780 from 2013y.
After I broken my first (orginal) motherboard I decided to buy softbriced motherboard on local marked for 1 $ and try to fix it.
This motherboard arived to me with symtomps:
- after turn on -> charging logo only and red led
I tried to load ROM but I had a lot of problems with MTK drivers (I had error in SPflash: "Sp_flash tool error (4001). I read a lot of threads from this forum and found a lot of solutions (from Stympy user etc). I found MTK Driver Gooooooddddd or somethink and I can start to flash my lenovo but I forgot to set "DL DA Check Sum" After finish of flash I get green circle.
But after this lenovo start to bootloop with "TOOL DL image fail" and still reset after few seconds till I put red "reset" button.
When I connect it to laptop - I see MTK Preloader Drived in Device Manager for few second and disappears. I can't start flash it again because I get messege "Flash Tooll Error 4001"
I tried a lot of SPtool version, Rom version and MTK Driver versions - still the same error after click Firmware->Upgrate and connect phone to usb
Can somebody try to find solution? Thx
Click to expand...
Click to collapse
Repeat the procedure pressing the small red button for 200 secconds whae you plug the usb cable for flash !
stympy said:
Repeat the procedure pressing the small red button for 200 secconds whae you plug the usb cable for flash !
Click to expand...
Click to collapse
Stympy
I tested connection with 200s (and 20s) red button pushed, but still the same issue.
After I release red button - I hear two times "windows new equipment connect" signal in laptop.
In SpFlash tool I see fast red 100% bar and messege "Error 4001".
mielczareklukasz.poczta said:
Stympy
I tested connection with 200s (and 20s) red button pushed, but still the same issue.
After I release red button - I hear two times "windows new equipment connect" signal in laptop.
In SpFlash tool I see fast red 100% bar and messege "Error 4001".
Click to expand...
Click to collapse
Can we do a team viewer sesion just to see the error and what is going on on your device manager ?
What windows do you have! Windows 8.1, 8, 7, xp ?
stympy said:
Can we do a team viewer sesion just to see the error and what is going on on your device manager ?
What windows do you have! Windows 8.1, 8, 7, xp ?
Click to expand...
Click to collapse
I use win7. Team viewer data I send you by mail.
mielczareklukasz.poczta said:
Hallo
I have problem with Lenovo P780 from 2013y.
After I broken my first (orginal) motherboard I decided to buy softbriced motherboard on local marked for 1 $ and try to fix it.
This motherboard arived to me with symtomps:
- after turn on -> charging logo only and red led
I tried to load ROM but I had a lot of problems with MTK drivers (I had error in SPflash: "Sp_flash tool error (4001). I read a lot of threads from this forum and found a lot of solutions (from Stympy user etc). I found MTK Driver Gooooooddddd or somethink and I can start to flash my lenovo but I forgot to set "DL DA Check Sum" After finish of flash I get green circle.
But after this lenovo start to bootloop with "TOOL DL image fail" and still reset after few seconds till I put red "reset" button.
When I connect it to laptop - I see MTK Preloader Drived in Device Manager for few second and disappears. I can't start flash it again because I get messege "Flash Tooll Error 4001"
I tried a lot of SPtool version, Rom version and MTK Driver versions - still the same error after click Firmware->Upgrate and connect phone to usb
Can somebody try to find solution? Thx
Click to expand...
Click to collapse
i had come across the same problem. after extensive research i came across one hint. the error could be due to wrong sp flash tool. so i downloaded the rom and the sp flashtool from the same site
go to needrom.com download/lenovo-p780-4-4-2-vibe-ui-2-0
download both rom and the sp flash tool from the same place
it should work. let me know.
mobin79 said:
i had come across the same problem. after extensive research i came across one hint. the error could be due to wrong sp flash tool. so i downloaded the rom and the sp flashtool from the same site
go to needrom.com download/lenovo-p780-4-4-2-vibe-ui-2-0
download both rom and the sp flash tool from the same place
it should work. let me know.
Click to expand...
Click to collapse
I downloaded these packed I tested - still the same problem with error 4001.
mielczareklukasz.poczta said:
I downloaded these packed I tested - still the same problem with error 4001.
Click to expand...
Click to collapse
i had formated my mobile before i loaded the new rom. also recheck the path in the sp flash tool. check that its showing the path correctly to the specified scatter file.

Bluboo s1 SP flash help pretty please

Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Tomaskaos said:
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Click to expand...
Click to collapse
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
SubwayChamp said:
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
Click to expand...
Click to collapse
Thanks!!! It works!!!!
Just be very careful. The USB C connector port in the phone is very loose... so make sure you can hold the cable tight other wiser it will lose the connection and brick your phone. For me, I had to remove the Plastic cover to be able to hold the power cable tight!
Hi, could you help me please? I did your steps, but it is not working. Sp flash does all its job, shows the green sign, but the phone stills dead. What I noticed the usb connects with the phone, then it disconnects. I tried to install the drivers as the tutorials say like deactivating the driver signature enforcement, but nothig happens well.

Categories

Resources