Hello all, I'm on D855,and after few attempts I managed to get Xposed working. I had issues with SDK 21 thing.
Now its working but can't se 'table thing' on there. It just says 'version 74 is active' with no possibility to press Install/Update. There is screen shot. Is this behavior normal for xposed, or I did something wrong?
Thanks.
Sorry, posted it here instead of general. And now don't know how to delete it...
Sorry.
-
mrpi64 said:
if you installed the xposed installer apk, then that's one step done. but, unless you haven't flashed the xposed SDK zip yet, you'll need to do that - it's the (or at least probably the easiest) way to install xposed. flash it with a custom recovery or whatever else you have, and after a reboot you should see that it tells you the SDK is installed, and from there you can browse and pick modules from the repo.
I'm not sure if that answers your question (was in a bit of a hurry so skimmed read it incorrectly so no, it doesn't answer the question ), but in general (at least for me), those buttons are blanked out, and I do everything by flashing.
Click to expand...
Click to collapse
Thanks.
Xosed works. Mods are working, I just needed to know is the installation ok, cause, it wouldn't be the first time for something working, but making phone slower due to bad installation.
Sent from my LG-D855 using Tapatalk
-
mrpi64 said:
the buttons on mine are the same as on yours - disabled. everything seems to be normal though, and I don't see anything going wrong, so I would *assume* it's fine.
---------- Post added at 09:47 AM ---------- Previous post was at 09:35 AM ----------
just to confirm, here's a screenshot of my device. maybe it's the device itself or something's been configured so that the xposed installer cannot modify the SDK installation. but, like I said, it's normal for me and even if it wasn't the most normal thing you can always perform the operations through recovery anyway
Click to expand...
Click to collapse
Thanks.
Than it's all good.
Now, can anyone tell me mod to disable nav bar on g3. I did that with gravity on Nexus, and can't find option on xposed. I can, but it remove them permanently.thanks
Live long and prosper.
-
mrpi64 said:
there is a G3 tweakbox here, not sure if it's what you're looking for but I hope this helps
Click to expand...
Click to collapse
Tweakbox doesn't seems to have that option. It have remove nav bar, and it disable bar permanently. Unless I'm missing something.
Live long and prosper.
-
mrpi64 said:
are you looking to temporarily or permanently remove it?
Click to expand...
Click to collapse
Well I would like something like extended display (it's called like that in CM I think) or PIE from Paranoid android.
So to have them, but hidden.
Stock option doesn't work as it keeps them on launcher and keyboard.
Live long and prosper.
-
mrpi64 said:
there are a few xposed modules (I think, at least one) which give you Pie/expanded desktop - would a module like GravityBox work?
Click to expand...
Click to collapse
Of course, but can't find mod like that for G3...
Live long and prosper.
-
mrpi64 said:
have you tried GravityBox? and I'm guessing you're running an AOSP stock ROM?
Click to expand...
Click to collapse
As I understand GravityBox is for Nexus. I'm on Cloudy for G3,and that is stock based custom rom.
Live long and prosper.
-
Related
Hi,
I just installed the V16 Update for my Galaxy SIII with Ultima. The system works fine but I'm missing some things that were present in the previous Rom (V15.1). The main thing what I miss is the Touchwiz launcher, in the previous Rom I could decide which launcher I want to use, now I have an other launcher (I can't even tell you which one it is) so is there an option to get Touchwiz back on the device ? The second thing that is bothering me, is the CRT off animation. I just can't find the option to disable it like in the old Rom maybe I'm blind or something but I don't see it.
The only thing that isn't working as it should, is the application gravitybox, it tells me everytime: "GravityBox system framework not responding" I already found out that I may have to update Xposed framework and reboot the device but it just doesen't work. app_proccess is active 47 and XposedBridge.jar is 42.
Hope you can help me with this.
Thanks for every response
And sorry for the title I don't know anything better
0Rage_Assassin said:
Hi,
I just installed the V16 Update for my Galaxy SIII with Ultima. The system works fine but I'm missing some things that were present in the previous Rom (V15.1). The main thing what I miss is the Touchwiz launcher, in the previous Rom I could decide which launcher I want to use, now I have an other launcher (I can't even tell you which one it is) so is there an option to get Touchwiz back on the device ? The second thing that is bothering me, is the CRT off animation. I just can't find the option to disable it like in the old Rom maybe I'm blind or something but I don't see it.
The only thing that isn't working as it should, is the application gravitybox, it tells me everytime: "GravityBox system framework not responding" I already found out that I may have to update Xposed framework and reboot the device but it just doesen't work. app_proccess is active 47 and XposedBridge.jar is 42.
Hope you can help me with this.
Thanks for every response
And sorry for the title I don't know anything better
Click to expand...
Click to collapse
Not sure on TouchWiz, as I don't use it... I'm sure someone will be along who will know.
The CRT animation is now part of the GravityBox settings, so until you get that up and running, you won't be able to customize much at all. Did you run the "Xposed Installer"? If so, go into that, and at the very top left there is a dropdown box. Choose 'modules' and make sure gravity box is ticked, then reboot.
BlueMeany68 said:
Not sure on TouchWiz, as I don't use it... I'm sure someone will be along who will know.
The CRT animation is now part of the GravityBox settings, so until you get that up and running, you won't be able to customize much at all. Did you run the "Xposed Installer"? If so, go into that, and at the very top left there is a dropdown box. Choose 'modules' and make sure gravity box is ticked, then reboot.
Click to expand...
Click to collapse
Ok Gravitybox is working now after ticking it in the Xposed Installer app -.- Thank you for this Just hoping anyone knows something about touchwiz..
My recently acquired S4 was rooted and running 4.4.2/NC5 and SafeStrap 3.72 just fine. Then I went and flashed Hyperdrive 18.1
Now I have Hyperdrive 18.1 rom running but no more root access, Safestrap recovery, or Wifi access.
I'm not sure where to go from here, and can't seem to find any golden nuggets in the forums. Anyone?
Lexus One said:
My recently acquired S4 was rooted and running 4.4.2/NC5 and SafeStrap 3.72 just fine. Then I went and flashed Hyperdrive 18.1
Now I have Hyperdrive 18.1 rom running but no more root access, Safestrap recovery, or Wifi access.
I'm not sure where to go from here, and can't seem to find any golden nuggets in the forums. Anyone?
Click to expand...
Click to collapse
Towelroot.com for root. Download the APK and install. Go into the app and "make it rain". SuperSU from the playstore. Busybox installer from the play store. Go into Busybox and "install busybox". Download the Safestrap APK of the XDA thread. Install the APK. Go into Safestrap and "install recovery". Boot into Safestrap and flash this.... https://www.androidfilehost.com/?fid=23501681358539843 for the wifi. Profit.
Jesus loves you!
Lexus One said:
My recently acquired S4 was rooted and running 4.4.2/NC5 and SafeStrap 3.72 just fine. Then I went and flashed Hyperdrive 18.1
Now I have Hyperdrive 18.1 rom running but no more root access, Safestrap recovery, or Wifi access.
I'm not sure where to go from here, and can't seem to find any golden nuggets in the forums. Anyone?
Click to expand...
Click to collapse
Don't forget to keep all the files you need on the SD card just in case.
liljoe727 said:
Towelroot.com for root. Download the APK and install. Go into the app and "make it rain". SuperSU from the playstore. Busybox installer from the play store. Go into Busybox and "install busybox". Download the Safestrap APK of the XDA thread. Install the APK. Go into Safestrap and "install recovery". Boot into Safestrap and flash this.... https://www.androidfilehost.com/?fid=23501681358539843 for the wifi. Profit.
Jesus loves you!
Click to expand...
Click to collapse
Amen! Thanks, that was good advice. I'm back to having root, safestrap, and wifi. Incidentally, was I supposed to set SeLinux to permissive before installing Safestrap? I vaguely remember watching an S4 video that said that I should do that to be sure safestrap installed correctly.
Next time flash the supersu.zip in safestrap immediately after the rom.
Lexus One said:
Amen! Thanks, that was good advice. I'm back to having root, safestrap, and wifi. Incidentally, was I supposed to set SeLinux to permissive before installing Safestrap? I vaguely remember watching an S4 video that said that I should do that to be sure safestrap installed correctly.
Click to expand...
Click to collapse
You can. I never have I do not think. If you have issues you can always uninstall/reinstall.
Jesus loves you!
Hey guys, I was having the same issue and your advice in this thread fixed it for me.
I've still got two more problems that I thought would be appropriate to ask in this thread;
Most importantly, the GPS seems to be not enabled. I can't find anywhere to enable it and I can't make it show up in the status-bar from the hyperdrive tweaks app.
Also, (and this is more a nuisance, I can live without it for now) the clock doesn't appear at the top of my screen. How can I make that show up?
On a complete side note, besides supporting the developer is there any reason to buy the pro apps? I'm considering buying the 71$ version if everything works well just to support the staff but it seems like a whole lot of money if it doesn't enable any features I'd use. I don't know, on the one hand I want to support the developer, but on the other hand it seems like a lot of money and doesn't go with the spirit of the android platform or modding community in general.
liljoe727 said:
You can. I never have I do not think. If you have issues you can always uninstall/reinstall.
Jesus loves you!
Click to expand...
Click to collapse
i had to change selinux to permissive to get it to work. i guess its a YMMV type thing
liljoe727 said:
Towelroot.com for root. Download the APK and install. Go into the app and "make it rain".
Click to expand...
Click to collapse
I had the Safestrap, SU and NC5 files already on my SD card. For some reason after flashing 18.1 I lost root. Towelroot saved my ass this morning! Thanks for posting the suggestion.
cdroid93 said:
Hey guys, I was having the same issue and your advice in this thread fixed it for me.
I've still got two more problems that I thought would be appropriate to ask in this thread;
Most importantly, the GPS seems to be not enabled. I can't find anywhere to enable it and I can't make it show up in the status-bar from the hyperdrive tweaks app.
Also, (and this is more a nuisance, I can live without it for now) the clock doesn't appear at the top of my screen. How can I make that show up?
On a complete side note, besides supporting the developer is there any reason to buy the pro apps? I'm considering buying the 71$ version if everything works well just to support the staff but it seems like a whole lot of money if it doesn't enable any features I'd use. I don't know, on the one hand I want to support the developer, but on the other hand it seems like a lot of money and doesn't go with the spirit of the android platform or modding community in general.
Click to expand...
Click to collapse
Sorry it took so long to get back to you.
As far as I know, the donation option does not unlock anything you do not already have. It only removes the waiting period in accessing HyperDrive Tweaks. If you really like it then donate. I have not heard of the GPS issue before so I can not be of help. As far as the clock, did you try playing around with its location in HyperDrive Tweaks?
liljoe727 said:
Sorry it took so long to get back to you.
As far as I know, the donation option does not unlock anything you do not already have. It only removes the waiting period in accessing HyperDrive Tweaks. If you really like it then donate. I have not heard of the GPS issue before so I can not be of help. As far as the clock, did you try playing around with its location in HyperDrive Tweaks?
Click to expand...
Click to collapse
No worries; I'm still alive.
Are you sure about the pro keys? I bought the bronze edition and it seems that there are still some settings in the hyperdrive tweaks that are disabled.
I figured out the GPS: The toggle button was in the statusbar, then I rebooted once and it wasn't anymore which is why I freaked. I found out how to choose my buttons in the statusbar so I put the GPS back.
As far as the clock; I've looked through all of the hyperdrive tweaks and paged through all my system settings. I never saw an option to enable or disable the clock, nor did I see an option to change the position. I did changed the clock settings that I saw (like you I thought the OS would magically figure it out if its attention was called to the clock) and it didn't help
cdroid93 said:
No worries; I'm still alive.
Are you sure about the pro keys? I bought the bronze edition and it seems that there are still some settings in the hyperdrive tweaks that are disabled.
I figured out the GPS: The toggle button was in the statusbar, then I rebooted once and it wasn't anymore which is why I freaked. I found out how to choose my buttons in the statusbar so I put the GPS back.
As far as the clock; I've looked through all of the hyperdrive tweaks and paged through all my system settings. I never saw an option to enable or disable the clock, nor did I see an option to change the position. I did changed the clock settings that I saw (like you I thought the OS would magically figure it out if its attention was called to the clock) and it didn't help
Click to expand...
Click to collapse
All tweaks settings are enabled, the keys are only to get rid of the time delay popup.
All clock settings are in the status bar tab of HD tweaks. "Clock alignment" has the options for its position and visibility.
Credit for this goes to another user in another discussion forum. I just wanted to put it in a proper forum to help folks.
Please discuss your victories and defeats with your modules.
I currently use two modules: YouTube Ad Blocker and Greenify Experimental Settings. Test your Greenify settings one at a time. I have found that allowing hibernation of system processes causes an occasional bootloop. I think it's related to just one or two apps, so I'm trying to isolate those.
Xposed APK will be attached momentarily. I have to switch to a desktop.
Thanks!
jumpup said:
Credit for this goes to another user in another discussion forum. I just wanted to put it in a proper forum to help folks.
Please discuss your victories and defeats with your modules.
I currently use two modules: YouTube Ad Blocker and Greenify Experimental Settings. Test your Greenify settings one at a time. I have found that allowing hibernation of system processes causes an occasional bootloop. I think it's related to just one or two apps, so I'm trying to isolate those.
Xposed APK will be attached momentarily. I have to switch to a desktop.
Click to expand...
Click to collapse
I've been having issues with apps not staying hibernated (Greenify), and when I tried Xposed, my Venue 8 became unstable. I've installed your version; and so far, so good! I'm using Greenify Experimental and Amplify.
urquiagal said:
I've been having issues with apps not staying hibernated (Greenify), and when I tried Xposed, my Venue 8 became unstable. I've installed your version; and so far, so good! I'm using Greenify Experimental and Amplify.
Click to expand...
Click to collapse
@urquiagal same here. Glad to hear you are having success with Xposed as well.
I hope more interest in the Venue 8 7840 comes our way. This is an amazing system.
I spoke too soon ...
{sigh}
A couple of nights ago my Venue started bootlooping again, and it wouldn't stop until I uninstalled XPosed. I wanted so badly for this to work.
Is the xposed bootloop issue just a problem with the stock ROM, or does it happen with custom ROMs too? I've never flashed a non-stock ROM on any of my devices, but I think I'd be willing to try with the Venue if that would let me use Greenify's full functionality.
Slightly OT: is it possible to put a Venue 3830 into "safe mode"? Not wanting to do another factory reset (still a pain even with Titanium restore), it took me a LOT of bootloop cycles trying to uninstall xposed in 10-15 second intervals. (And why does the Venue app list only scroll one way?) I finally managed to put the StatsOf icon on the primary home screen, change my settings to open the app list first, sort the app list so that xposed was on the first "page", and long-press the xposed entry long enough to get the delete prompt before it looped again. Did a hard reboot at that point and the loop was gone.
urquiagal said:
{sigh}
A couple of nights ago my Venue started bootlooping again, and it wouldn't stop until I uninstalled XPosed. I wanted so badly for this to work.
Is the xposed bootloop issue just a problem with the stock ROM, or does it happen with custom ROMs too? I've never flashed a non-stock ROM on any of my devices, but I think I'd be willing to try with the Venue if that would let me use Greenify's full functionality.
Slightly OT: is it possible to put a Venue 3830 into "safe mode"? Not wanting to do another factory reset (still a pain even with Titanium restore), it took me a LOT of bootloop cycles trying to uninstall xposed in 10-15 second intervals. (And why does the Venue app list only scroll one way?) I finally managed to put the StatsOf icon on the primary home screen, change my settings to open the app list first, sort the app list so that xposed was on the first "page", and long-press the xposed entry long enough to get the delete prompt before it looped again. Did a hard reboot at that point and the loop was gone.
Click to expand...
Click to collapse
No custom Roms or development at all for this tablet yet.
urquiagal said:
{sigh}
A couple of nights ago my Venue started bootlooping again, and it wouldn't stop until I uninstalled XPosed. I wanted so badly for this to work.
Is the xposed bootloop issue just a problem with the stock ROM, or does it happen with custom ROMs too? I've never flashed a non-stock ROM on any of my devices, but I think I'd be willing to try with the Venue if that would let me use Greenify's full functionality.
Slightly OT: is it possible to put a Venue 3830 into "safe mode"? Not wanting to do another factory reset (still a pain even with Titanium restore), it took me a LOT of bootloop cycles trying to uninstall xposed in 10-15 second intervals. (And why does the Venue app list only scroll one way?) I finally managed to put the StatsOf icon on the primary home screen, change my settings to open the app list first, sort the app list so that xposed was on the first "page", and long-press the xposed entry long enough to get the delete prompt before it looped again. Did a hard reboot at that point and the loop was gone.
Click to expand...
Click to collapse
Leave the Xposed installed, but disable the Greenify module. That will likely solve it.
No custom ROMs are out yet. If you need it, the Dell 4.4.4 factory ROM is posted in Venue General (7840 ROM, that is)
What is the best root method you guys have used?
Venue 8 7840 only supports tethered CWM at this time
spotdog14 said:
What is the best root method you guys have used?
Click to expand...
Click to collapse
@spotdog14 - The only way to access a recovery and install SuperSU is through a tethered CWM recovery session made for Intel x86 Android tablets - Check this thread - http://forum.xda-developers.com/android/development/intel-android-devices-root-temp-cwm-t2975096
On another note: What do you folks think about creating a generic Venue 7840 "Tips and Tricks/What-We-Know-So-Far" thread and compile this info? I would be glad to lead this.
Thanks!
J.
spotdog14 said:
What is the best root method you guys have used?
Click to expand...
Click to collapse
@spotdog14 - BTW, your signature is beyond awesome
jumpup said:
On another note: What do you folks think about creating a generic Venue 7840 "Tips and Tricks/What-We-Know-So-Far" thread and compile this info? I would be glad to lead this.
Click to expand...
Click to collapse
That would probably be a good idea - it's all dotted around at the moment and mixed in with the other venue tablets.
anggusss said:
That would probably be a good idea - it's all dotted around at the moment and mixed in with the other venue tablets.
Click to expand...
Click to collapse
A couple of weeks ago, I put in a request for a dedicated Venue 7840 forum. Here is what I'm thinking:
Intro
Guides
[**]Tethered CWM Recovery + SuperSU
[**]Xposed module install
[**]Format microSD for support up to 512GB
Resources
[**]Dell 4.4.4 CWM Nandroid rooted image
[**]APKs of Dell-specific apps (Camera, Gallery, etc. - whatever will work as such)
Anything else?
jumpup said:
@spotdog14 - The only way to access a recovery and install SuperSU is through a tethered CWM recovery session made for Intel x86 Android tablets - Check this thread - http://forum.xda-developers.com/android/development/intel-android-devices-root-temp-cwm-t2975096
On another note: What do you folks think about creating a generic Venue 7840 "Tips and Tricks/What-We-Know-So-Far" thread and compile this info? I would be glad to lead this.
Thanks!
J.
Click to expand...
Click to collapse
Awesome, thanks! I had some problems finding the right ADB driver but it all worked out. I ended up using option 3 and got an error about too many links but it still booted fine into recovery and I was able to flash SU just fine. The first two apps to install here Adaway and xposed.
**Edit**
I have a question, this is obviously an older version of xposed and one of the modules I use is App Settings and it is saying it requires XposedBridge Version 52. Is it safe to update Xposed from inside the app or should I try downloading an older version of App Settings?
I would not recommend updating Xposed just yet. One of the modules that I use is YouTube adblock, and it complained about not having the latest framework. It still worked, though.
The reason I posted this Xposed (found on another Android x86 forum) was that when I tried the latest framework, I got an immediate bootloop.
Fortunately, though, if you have a problem, you can boot to Android Safe Mode and have enough time to remove Xposed. Boot the system while holding down both VolUp+VolDn, and it'll boot to Safe Mode.
RE: Adblock -> That's my first order of business. Install FDroid+Adblock. It is night-and-day performance boost on Android.
spotdog14 said:
Awesome, thanks! I had some problems finding the right ADB driver but it all worked out. I ended up using option 3 and got an error about too many links but it still booted fine into recovery and I was able to flash SU just fine. The first two apps to install here Adaway and xposed.
**Edit**
I have a question, this is obviously an older version of xposed and one of the modules I use is App Settings and it is saying it requires XposedBridge Version 52. Is it safe to update Xposed from inside the app or should I try downloading an older version of App Settings?
Click to expand...
Click to collapse
jumpup said:
I would not recommend updating Xposed just yet. One of the modules that I use is YouTube adblock, and it complained about not having the latest framework. It still worked, though.
The reason I posted this Xposed (found on another Android x86 forum) was that when I tried the latest framework, I got an immediate bootloop.
Fortunately, though, if you have a problem, you can boot to Android Safe Mode and have enough time to remove Xposed. Boot the system while holding down both VolUp+VolDn, and it'll boot to Safe Mode.
RE: Adblock -> That's my first order of business. Install FDroid+Adblock. It is night-and-day performance boost on Android.
Click to expand...
Click to collapse
That is kind of what I figured. I just wish I could get App Settings to work.
Also it appears I cannot get Xposed GEL Settings to work correctly either. I'm going to try to uninstall it and reinstall it later today to see if that makes any difference.
I haven't tried Xposed GEL yet. Let me know how that goes. What I figure we could do in the compiled 7840 info thread is include what's been tried and a "Yes/No/Kinda" section of how apps/modules are performing.
spotdog14 said:
That is kind of what I figured. I just wish I could get App Settings to work.
Also it appears I cannot get Xposed GEL Settings to work correctly either. I'm going to try to uninstall it and reinstall it later today to see if that makes any difference.
Click to expand...
Click to collapse
jumpup said:
I haven't tried Xposed GEL yet. Let me know how that goes. What I figure we could do in the compiled 7840 info thread is include what's been tried and a "Yes/No/Kinda" section of how apps/modules are performing.
Click to expand...
Click to collapse
Sounds good to me. After reinstalling GEL settings worked fine. I'm thinking about applying gravity box next. I miss my customizable quick toggles.
Update, Gravity Box KK works, but you cannot disable or move the quick access settings for:
My Dell
Sound
Dell Cast
But from my brief test everything else seems to be working fine.
@spotdog14 - Thank you for posting your findings. I will roll this into the general thread.
Som sad news, though. I traded in my Venue 7840 for a Galaxy Note 10.1 2014 Edition. I really needed the pen capability. Nonetheless, I have the info I need to set up the 7840 general forum.
I am currently uploading Dell's factory 4.4.4 image as Nandroid. It should be pre-rooted, but if not, use the tethered CWM to install the latest SuperSU.
spotdog14 said:
Update, Gravity Box KK works, but you cannot disable or move the quick access settings for:
My Dell
Sound
Dell Cast
But from my brief test everything else seems to be working fine.
Click to expand...
Click to collapse
I used this tool to install xposed from day one and has worked great for me the past couple months. It's 2.6.1
http://forum.xda-developers.com/xposed/modules/tool-installer-xposed-installer-zenfones-t2983589
Worked like a charm.
Hey guys
Its been a few year since I rooted. don't worry ive already spotted the guide on how to.
My question is once im rooted. Does the old Xposed framework thingy still exist?
What app are we using for govenor/kernel control?
Is titanium backup still a good option?
Basically, whats my app suite gonna look like when im done? How am I going about tweaking my phone?
I guess im asking whats your set of default apps for your rooted phone. Mangment, tweak, backuo, gapps etc
If you have the xperia xz1, which is on android 8, oreo I don't believe Xposed framework is working on oreo yet. I also believe only one kernal is working to get root, not sure if it has any governor controls though. Titanium is still good for removing unwanted bloat.
To answer about xposed, it still work on oreo but this is a beta take a look at my attachment, I have a XZ1 Running oreo 8.0.0 firmware 47.1.A.12.75 and Xposed is working on it, I flashed it through TWRP
Hope it helped
Thank you
Just wanting to get back on the root shoot.
Even if im just rooting and trimming all the fat out. Xposed looks good. Cant wait to take all the bloatware out. Is there a "safe to remove" list about? At work ATM, but will be diving right into this this week
7hr08ik said:
Thank you
Just wanting to get back on the root shoot.
Even if im just rooting and trimming all the fat out. Xposed looks good. Cant wait to take all the bloatware out. Is there a "safe to remove" list about? At work ATM, but will be diving right into this this week
Click to expand...
Click to collapse
from trial and error there isn't a lot of "safe to remove" items, I trimmed out 5 maybe 6 items before the rom got squirrelly.
This is just from memory but I got rid of avg, chrome (I use Iron browser) email and exchange, amazon and wiki links, as well as the system facebook and youtube ( to give more control over those items) Just about anything else resulted in apps force closing or other issues
Thanks guys,
Seems like its all just about how it was. Give or take a few apps.
My last thing I wonder is, how do I run barclays bank app? Im pretty sure it'll not run due to the root. Is there a way round this? Sandbox or something?
I think I just found my answer. Wondering what Magisk was ???
So with magisk I can run banking apps etc. It will also manage all of my root blah blah. Xposed can help me **** about with things. Titanium backup. And new OS.
I think im ready now ?
If you run Xposed, you lose a large chunk of the MagiskHide capabilities. You're better off without Xposed and just using Magisk
Really? That's bad. I remember xposed was fun. I shall have a read up on Magisk when I get time.
Planning on the weekend. So I can have a full day of it ?
7hr08ik said:
Hey guys
Its been a few year since I rooted. don't worry ive already spotted the guide on how to.
My question is once im rooted. Does the old Xposed framework thingy still exist?
What app are we using for govenor/kernel control?
Is titanium backup still a good option?
Basically, whats my app suite gonna look like when im done? How am I going about tweaking my phone?
Click to expand...
Click to collapse
I recommend you to use EXKM (for kernel control) and FX File Browser (with the root addon) for all the debloating and modifications in the system folders.
Hey,
Ive never heard of EXKM. But still using FX browser since last time I rooted. Never switched ?
Hello.
You can install greenify4magisk, sd maid for cleaning, myandroidtool (do what amplify do but without Xposed)
7hr08ik said:
Hey,
Ive never heard of EXKM. But still using FX browser since last time I rooted. Never switched ?
Click to expand...
Click to collapse
EXKM = ElementalX Kernel Manager.
Works perfect with XZ1 / XZ1 Compact.
xFirefly93 said:
EXKM = ElementalX Kernel Manager.
Works perfect with XZ1 / XZ1 Compact.
Click to expand...
Click to collapse
Thank you. Been busy as hell this week. But shall be rooting asap
ok so.
Ive unlocked the bootloader
followed this guide
https://forum.xda-developers.com/xperia-xz1/how-to/guide-how-to-persistant-root-xperia-xz1-t3718375
And everything worked fine
But i want to install CarbonROM
At what point in that guide do i install CarbonROM? Because my phone has been sat here at the boot "Sony" screen for about 30 mins now, and im pretty sure its not gonna boot up
Ok,
This is doing my head in now.
Twice now ive had to do a full reinstall, how in the living hell do I get xposed installed ontop of magisk?
I think install the xposed installer, then the SDK 26 from magisk. Then reboot? But it bootlooped on me?
Did I technogology wrong?
7hr08ik said:
Ok,
This is doing my head in now.
Twice now ive had to do a full reinstall, how in the living hell do I get xposed installed ontop of magisk?
I think install the xposed installer, then the SDK 26 from magisk. Then reboot? But it bootlooped on me?
Did I technogology wrong?
Click to expand...
Click to collapse
On the latest version ( .179) , you can't use xposed with magisk. There is nothing to do but waiting right now . We have to wait beta 4 or whatever.
Ah, right.
But am I getting the install procedure correct?
Im not even sure theres anything in closed I actually want. But its an option, therefore I must put it in ?
https://www.xda-developers.com/enable-quick-wallet-access-google-pay-pixel-android-10/
The gestures appears and the bottom power menu is there but the cards and passes switch in gestures disappears after a period of time. Anybody get it working?
warrencoakley said:
The gestures appears and the bottom power menu is there but the cards and passes switch in gestures disappears after a period of time. Anybody get it working?
Click to expand...
Click to collapse
On Android 9 or earlier? I just tried it on PQ3A.190801.002 and the option will not appear for me in the Gestures settings.
spsupjewski13 said:
On Android 9 or earlier? I just tried it on PQ3A.190801.002 and the option will not appear for me in the Gestures settings.
Click to expand...
Click to collapse
Do you have Viper installed? If so unistall it and it will work. If you need Viper roll back to a previous version. It doesn't play well with v2.7
warrencoakley said:
Do you have Viper installed? If so unistall it and it will work. If you need Viper roll back to a previous version. It doesn't play well with v2.7
Click to expand...
Click to collapse
I did once have Viper, but uninstalled it some time ago.
spsupjewski13 said:
I did once have Viper, but uninstalled it some time ago.
Click to expand...
Click to collapse
Mmmm ok. I have found that Viper interferes with some of the modules. All I can say to you is to is to start the process of elimination with your modules and start unistalling them and reinstalling and check by pressing the power button to see if the cards appear. Obviously keeping the card & passes module in Magisk though.
warrencoakley said:
Mmmm ok. I have found that Viper interferes with some of the modules. All I can say to you is to is to start the process of elimination with your modules and start unistalling them and reinstalling and check by pressing the power button to see if the cards appear. Obviously keeping the card & passes module in Magisk though.
Click to expand...
Click to collapse
Luckily I did not have many modules to work through, unluckily removing them did not solve the issue. I'll keep fiddling with things and let you know if anything fixes this.
spsupjewski13 said:
Luckily I did not have many modules to work through, unluckily removing them did not solve the issue. I'll keep fiddling with things and let you know if anything fixes this.
Click to expand...
Click to collapse
Do you have a custom kernal installed?
warrencoakley said:
Do you have a custom kernal installed?
Click to expand...
Click to collapse
I do not, stock Android 9.
spsupjewski13 said:
I do not, stock Android 9.
Click to expand...
Click to collapse
Bizzare. I'm out of ideas. Viper 2.7 was the one that was causing me the issue. I hope you can get it resolved.
warrencoakley said:
Bizzare. I'm out of ideas. Viper 2.7 was the one that was causing me the issue. I hope you can get it resolved.
Click to expand...
Click to collapse
Same here, thanks for the advice though. I'll be sure to let you know if I get it running.
Do you suppose it could be my SQLite binary? Currently I have sqlite3 from TitaniumBackup.
Edit: Doesn't appear to be that. Removed all of my Titanium files and added a new sqlite3 to my bin without success.
spsupjewski13 said:
Do you suppose it could be my SQLite binary? Currently I have sqlite3 from TitaniumBackup.
Edit: Doesn't appear to be that. Removed all of my Titanium files and added a new sqlite3 to my bin without success.
Click to expand...
Click to collapse
Do you have all the modules for GPay installed? Does your GPay work?
warrencoakley said:
Do you have all the modules for GPay installed? Does your GPay work?
Click to expand...
Click to collapse
I have my cards added and everything. I haven't tried using tap to pay, but I assume it will function fine.
spsupjewski13 said:
I have my cards added and everything. I haven't tried using tap to pay, but I assume it will function fine.
Click to expand...
Click to collapse
Really don't know. Maybe when January's security update comes out start from scratch and see.
spsupjewski13 said:
I have my cards added and everything. I haven't tried using tap to pay, but I assume it will function fine.
Click to expand...
Click to collapse
It seems the January update and broke something and it disappears again. Did you get it to work.
warrencoakley said:
It seems the January update and broke something and it disappears again. Did you get it to work.
Click to expand...
Click to collapse
Afraid not, I'll just have to keep waiting and see I suppose.
spsupjewski13 said:
Afraid not, I'll just have to keep waiting and see I suppose.
Click to expand...
Click to collapse
Do you have a custom Kernal installed?
warrencoakley said:
Do you have a custom Kernal installed?
Click to expand...
Click to collapse
I do not. Totally stock Android with only a few modules installed, and I've tried removing all of them too.
spsupjewski13 said:
I do not. Totally stock Android with only a few modules installed, and I've tried removing all of them too.
Click to expand...
Click to collapse
Did you install these and the zip?
GPay-SQLite-Fix Magisk Module
SQLite for ARM aarch64 devices