Related
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Veesais said:
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Click to expand...
Click to collapse
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
ParanoidKang said:
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
Click to expand...
Click to collapse
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Veesais said:
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Click to expand...
Click to collapse
Now the screen may not show, but try booting into fastboot mode by press and hold the Trackball+Power buttons together.
I'm not sure about the nexus one, but newer nexus devices have factory images, supplied by Google. If they exist for the nexus one, you should be able to save your device by flashing them through fastboot. That is if the images exist and you can get to fastboot.
Sent from my Nexus 4 using XDA Premium 4 mobile app
hi guys
so my galaxy s3 has had a faulty conector since ive had it. but yesterday when i went to flash stock rom as i wanted to clean the device etc it stopped half way through odin process and now it doesnt boot obvieously. the thing is now the phone conector seems to be completely broken as it wont connect for more than maybe 10 seconds at the start but now nothing at all but it does still charge. ive bought an original samsung cable brand new and still same result.
any ideas of a way to get my phone working again? it seems odin wiped my recovery in 10 seconds which sucks....
anything anyone can recommend i try?
DarkStryder said:
hi guys
so my galaxy s3 has had a faulty conector since ive had it. but yesterday when i went to flash stock rom as i wanted to clean the device etc it stopped half way through odin process and now it doesnt boot obvieously. the thing is now the phone conector seems to be completely broken as it wont connect for more than maybe 10 seconds at the start but now nothing at all but it does still charge. ive bought an original samsung cable brand new and still same result.
any ideas of a way to get my phone working again? it seems odin wiped my recovery in 10 seconds which sucks....
anything anyone can recommend i try?
Click to expand...
Click to collapse
Can you still get into download mode and does odin recognize it?
If not you will very likely need a jtag or take it into a service center.
Try replacing the usb port first, flashing anything on a phone with a broken port can corrupt the partition -which is what happened to you.
DarkStryder said:
hi guys
so my galaxy s3 has had a faulty conector since ive had it. but yesterday when i went to flash stock rom as i wanted to clean the device etc it stopped half way through odin process and now it doesnt boot obvieously. the thing is now the phone conector seems to be completely broken as it wont connect for more than maybe 10 seconds at the start but now nothing at all but it does still charge. ive bought an original samsung cable brand new and still same result.
any ideas of a way to get my phone working again? it seems odin wiped my recovery in 10 seconds which sucks....
anything anyone can recommend i try?
Click to expand...
Click to collapse
If the phone boots you could use mobile Odin but in your case,repairing the connector is the right way.
Sent from my GT-I9300 using XDA Free mobile app
Hi members,
Today morning suddenly my M4 aqua touch was not working.
I restarted phone using volume up + power button as per sony customer care guidance.
But after restarting only sony xperia logo comes and goes.
I repaired phone using sony pc companion. But no use.
After updating again sony xperia logo comes and goes continuously.
Please help me as service center is very far from my town.
Do you have access to your recovery?
Also, is your phone rooted. Gimme some details!
Sent from my SM-G530H using XDA Free mobile app
no..
heinrich.himmler said:
Do you have access to your recovery?
Also, is your phone rooted. Gimme some details!
Sent from my SM-G530H using XDA Free mobile app
Click to expand...
Click to collapse
No friend...its not rooted
Your phone seems to be stuck in a bootloop.
Press the Power button+Volume up button and hold, till you get a screen which is the recovery screen!
Now, you should be able to see options like Wipe Cache, and Factory reset.
In order to get out of this bootloop situation, first tap on Clear Cache.
Then tap on Factory reset.
THIS METHOD WILL DELETE ALL USER DATA.
But you can't really backup anything since you don't have access to the phone.
Try this out, and keep me posted.
Don't worry, All is Well!
Sent from my SM-G530H using XDA Free mobile app
No use
heinrich.himmler said:
Your phone seems to be stuck in a bootloop.
Press the Power button+Volume up button and hold, till you get a screen which is the recovery screen!
Now, you should be able to see options like Wipe Cache, and Factory reset.
In order to get out of this bootloop situation, first tap on Clear Cache.
Then tap on Factory reset.
THIS METHOD WILL DELETE ALL USER DATA.
But you can't really backup anything since you don't have access to the phone.
Try this out, and keep me posted.
Don't worry, All is Well!
Sent from my SM-G530H using XDA Free mobile app
Click to expand...
Click to collapse
After 3 hours phone booted normally...worked for 6 hours..
again touch is not working...again stuck at boot logo (comes and goes)
Try the solution I gave above
Sent from my SM-G530H using XDA Free mobile app
heinrich.himmler said:
Your phone seems to be stuck in a bootloop.
Press the Power button+Volume up button and hold, till you get a screen which is the recovery screen!
Now, you should be able to see options like Wipe Cache, and Factory reset.
In order to get out of this bootloop situation, first tap on Clear Cache.
Then tap on Factory reset.
THIS METHOD WILL DELETE ALL USER DATA.
But you can't really backup anything since you don't have access to the phone.
Try this out, and keep me posted.
Don't worry, All is Well!
Sent from my SM-G530H using XDA Free mobile app
Click to expand...
Click to collapse
hey i have this prob. too i tried to flash recovery.img and it bricked. im trying to do what you say but phone vibrates once then triple a sony logo comes and closes i need help please ((
sureshkadiri said:
Hi members,
Today morning suddenly my M4 aqua touch was not working.
I restarted phone using volume up + power button as per sony customer care guidance.
But after restarting only sony xperia logo comes and goes.
I repaired phone using sony pc companion. But no use.
After updating again sony xperia logo comes and goes continuously.
Please help me as service center is very far from my town.
Click to expand...
Click to collapse
Did you fix it? same as me :crying:
inspektors said:
Did you fix it? same as me :crying:
Click to expand...
Click to collapse
Download flashtool, flash http://forum.xda-developers.com/showthread.php?t=2489955
Set it up correctly and instal;l the drivers.
Download the ftf file for YOUR DEVICE, use this http://forum.xda-developers.com/cro...xperifirm-xperia-firmware-downloader-t2834142 ,or the last tab at the top of the flashtool.
Once you have found it, click it and download it by clicking it on the far right, make sure unpack automatically is checked.
Let it download and then flash tool will assemble it as the ftf file for you, and it will be in the correct folder. Cick the lightning button and select flash mode, select the ftf file that should apear in the list.
Folow the on screen instructions, it will take a while to flash, once finished it will say "unlug and reboot phone£
Do that and your done.
Cant fail with the flash tool
Let me know how you get on. Goodluck.
is your display ok (no small hairline cracks UNDER glass)?
I did all from your instructions and even try repair option in PC Companion but, had no errors but my e2303 remains stuck on the Sony logo (looping). I bought the phone online second hand and it arrived like that. I did bootloader unlock procedure in flashtool successfully and when i run it again it offers relock now so i assume it was good. However, if i try sony official bootloader unlock instructions via adb, i get error. I guess it's debug over usb and unknown sources related but since i can't boot to system there is no way to check that.
I'll mention i did try several ftf versions and all flashing went without errors (as with pc companion repair) but no result. Did i got scammed totally (i know i am as the phone should be working) and bought a phone that even can't get repaired?
Help guys
Do you have deleted or disabled my Xperia app before unlock? Maybe beacause this. I read when unlock and active my Xperia, phone is like paperweight
I got the phone like this, stuck on Sony/Xperia logo so i don't know what happened and what is the cause
Hi,
Apparently this is a more frequent issue than I'd have thought.... A relative of mine brought me his M4 Aqua e2303 with the same symptoms: it tries to boot, shows the Sony Logo (Xperia on the bottom of the screen) and it just loops. Screen goes off-then-on and the same thing. I've tried EVERYTHING. Bootloader was locked, so as a desperate measure I even unlocked it via Flashtool. First I tried Sony PC Companion App and automatic repair. It went smoothly but the phone was still stuck, then I flashed the last ROM via Flashtool. Again, everything went OK, but the phone was still stuck. I flashed a different ROM, the European Press version, since it's a little bit older, and suddenly something changed. The boot sequenced advanced from the Sony Screen to the waves screen, even with the music, but it just freezes and reboots itself 3 or 4 seconds after the blue-ish waves screen appears and the melody starts playing. Fastboot works, and I even pushed a custom recovery image. It boots, works, touchscreen and everything, and I can wipe everything (which I even did) but to no positive result. I've read about theft protection bricking some M4 Aqua phones, but this one had a locked bootloader, so it's out of the question (I think)
I'm absolutely dumbfounded... the only thing that comes to mind at this point is a hardware failure. My relative got the screen replaced, but everything was working fine after that, so I guess some cable/ribbon/whatever could get loose over time? Any idea?
I've learned a lot reading this thread and XDA Dev generally. Thanks, guys, great community.
hi,
i got to this problem too - M4 E2303:
1) unlocked bootloader
2) played around with the infinite possibilities of an unlocked bootloader.
3) killed android one way or another (debloating by hand, etc) - but it all worked again, thanks to the custom recovery
4) repeated step 3 a few times, until i liked the result
5) when creating the backup in recovery mode, the phone overheated constantly - so i submerged it
and this is how it went sour... i am still not sure, if the killing blow was dealt by heat, water or some other action - the phone just shuts down when i start it, while custom recovery works. flashing works also - over fastboot and the normal fashmode.
the interresting part is, that after flashing the bl back to locked even the sony recovery tool accepted it and flashed it again - but it won't boot anything else, just recovery (after unlocking and flashing it again, of course)
the only possibly useful info i got for you, is this log message in the twrp-console, which i did notice since then:
unable to recreate and-sec folder
maybe this helps others to identify the problem/solution for these strange bootloops
p.s.: even though it is only one possibility for what killed my phone: DO NOT use "the waterproof phone"(tm) under water
p.p.s: Cyanogenmod 12.1 works (well, as "well" as on any other m4) - i just installed that from an sdcard via twrp
I have a xperia m4 aqua, it have the same problems, but I´m thinking if a break glass or a crack has something to see with this problem, can you e-mail me? [email protected] please.
Hey, mine is also stuck in a bootloop.
had the wifi of for 3 days straight. Next time switching wifi on the phone just shuts down and gets stuck in a bootloop for like 45-60 minutes. Wifi is off, as soon as I activate wifi again. Same all over.
Any suggestions?
Did a restore from the original software also with other versions.
I guess its a hardware problem. But no glue how and why
got same problem here, could it be because glass is cracked?
tbo85 said:
Hey, mine is also stuck in a bootloop.
had the wifi of for 3 days straight. Next time switching wifi on the phone just shuts down and gets stuck in a bootloop for like 45-60 minutes. Wifi is off, as soon as I activate wifi again. Same all over.
Any suggestions?
Did a restore from the original software also with other versions.
I guess its a hardware problem. But no glue how and why
Click to expand...
Click to collapse
Ahm i have the same problem too. Please tell me how to use flash tools on mac os
Hello everyone,
I have the same problem. It started when i saw that i had no 4G internet connection, so i thought lets restart my phone and yes now its in the bootloop .
I tried all kinds of resets, i tried to flash my phone which i did with succes, but still have the bootloop.
Now i have some questions:
- when did your bootloop started?
- Did u play pokemon Go?
- Was your phone warm or cold?
- Could it be a storage thats full?
- Do i have to bring my phone back or do i have to buy a new one?
- Could it be an software update that caused this?
The pokemon go thing is because it is a possibility that the game overheated your phone and maybe some hardware got damaged because of that.
i'm not sure of this, but there is a great change that thats the problem.
Hope we find the answer.
Hello everyone in XDA forums ,
I don't really remember what exactly was the thing that I did in which I hard-bricked my Samsung Galaxy Ace (GT-S5830i), but it was a combo of rooting and then (OS)s installations... I rooted the phone successfully and as far as I remember I could even flash a KitKat firmware, but then it got bricked at some point after trying to flash some Cyanogenmod firmware [USING ROM MANAGER]... YES, I got to know that it's terrible to use ROM Manager for that purpose on the ACE but that was after I bricked my phone -_- (I still don't know why though; anyways...)
My smartphone is currently hard-bricked, meaning that I can't access download mode, recovery mode, or even fastboot mode; and I can't see a single thing on the screen (not even the Samsung Logo or the so-called "Yellow Triangle" , or even the Android Logo)... The only sign that my phone is still working (AND NOT AT ALL HARDWARE-DAMAGED) is the color of the screen which is (well you can say purple or kinda grey; also known as the background light/brightness)... I've tried the following:
1- All the normal button combos in all possible ways and conditions.
2- The (removing the battery, connecting the device to the PC/Laptop, clicking a button combo, and then inserting the battery while still holding the button combo) method.
3- I even tried the adb method, the SP Flash Tool method, and using a Jig.
So practically my main problem is that my phone can't even get to any mode and that it can't be recognized by any PC/Laptop not even after installing the drivers properly or changing the cables... If I just could get my Laptop to recognize it or even just get to the download mode without even having my Laptop to recognize it, then I'd be easily able to solve the whole problem.
P.S: PLEASE don't tell me that it's hardware-damaged or that I need to go to Samsung, cuz IT IS NOT HARDWARE-DAMAGED AT ALL and under the VERY SAME circumstances many people could unbrick their hard-bricked devices, and one of which is the Samsung Galaxy S3, just because they have an alternative method to boot (including the "booting from SD Card using a debrick image" method); and my warantee is void a VERY LONG time ago, since I bought the phone like 5 years ago.
Even if a software solution is still not known to the community it still is possible to unbrick my phone using a JTAG Repair device.
I really hope that somebody would be able to help me in solving this dilemma with a software method... Thank you anyways, and have a nice day / good night.
Similar brick here on my S5839i. I did something stupid and flashed everything including bootloader from a galaxy Y (S5360).
Now its not responding to any button combos,
When turned on I get a blank screen, then the camera LED blinks and the touch buttons light up and it stays on the blank screen.
If I can just get into download mode somehow it should all be fine.
My last hope now is to try a jig when I get my hands on one.
Also when plugged in, its recognized by windows as BCM21533-Thunderbird
Maybe anyone has been in a similar state and could help please?
Thanks
hasan291 said:
Similar brick here on my S5839i. I did something stupid and flashed everything including bootloader from a galaxy Y (S5360).
Now its not responding to any button combos,
When turned on I get a blank screen, then the camera LED blinks and the touch buttons light up and it stays on the blank screen.
If I can just get into download mode somehow it should all be fine.
My last hope now is to try a jig when I get my hands on one.
Also when plugged in, its recognized by windows as BCM21533-Thunderbird
Maybe anyone has been in a similar state and could help please?
Thanks
Click to expand...
Click to collapse
My Ace doesn't even get recognized by a Laptop or a PC... I tried the jig method as I mentioned before without any success ... Thanks for your reply mate Hope that you find a solution for your problem very soon
Bricked like yours!!
I HAVE THE EXACT SAME PROBLEM WITH MY GALAXY GRAND 2
Here is the problem...I BRICKED MY PHONE!!
I am not able to turn it on and my screen wont even show up!!!
I try pressing all the switches, tried to boot it to recovery mode, tried to normally boot it but NOTHING WORX!!!!!
"Its a SAMSUNG Phone Model Galaxy Grand2 SM-G7102"
what i did was i already had rooted my phone and already installed Cyanogenmod 12.1 and was working all fine until I thought of completely cleaning my device...
so i boot my phone to recovery mode, wiped dalvik's cache and cache partition and then clicked on wipe data/factory reset. The phone reseted and it showed the boot screen and then it showed optimizing apps and then it got suddenly stuck and switched OFF!!!!
BROTHER PLEASE HELP ME I AM IN NEED...I AM NOT RICH AND CAN'T AFFORD TO BUY A NEW PHONE. I ACTUALLY BROKE DOWN AND LITERALLY STARTED CRYING. I HOPE YOU CAN FIND A WAY TO STOP THE PAIN I AM FACING NOW. ?????
THANK YOU SO MUCH FOR HELPING ME OUT(IF U DO)
I WOULD BE REALLY GRATEFUL.
vaishnavjknair said:
I HAVE THE EXACT SAME PROBLEM WITH MY GALAXY GRAND 2
Here is the problem...I BRICKED MY PHONE!!
I am not able to turn it on and my screen wont even show up!!!
I try pressing all the switches, tried to boot it to recovery mode, tried to normally boot it but NOTHING WORX!!!!!
"Its a SAMSUNG Phone Model Galaxy Grand2 SM-G7102"
what i did was i already had rooted my phone and already installed Cyanogenmod 12.1 and was working all fine until I thought of completely cleaning my device...
so i boot my phone to recovery mode, wiped dalvik's cache and cache partition and then clicked on wipe data/factory reset. The phone reseted and it showed the boot screen and then it showed optimizing apps and then it got suddenly stuck and switched OFF!!!!
BROTHER PLEASE HELP ME I AM IN NEED...I AM NOT RICH AND CAN'T AFFORD TO BUY A NEW PHONE. I ACTUALLY BROKE DOWN AND LITERALLY STARTED CRYING. I HOPE YOU CAN FIND A WAY TO STOP THE PAIN I AM FACING NOW.
THANK YOU SO MUCH FOR HELPING ME OUT(IF U DO)
I WOULD BE REALLY GRATEFUL.
Click to expand...
Click to collapse
It would be my pleasure to help you bro (and of course everyone else) once I know how :crying: :laugh:
Hi, I need your advice please. Today I couldn't turn on my mobile phone (no update or something like that), so I tried recovery mode and it got stuck in loopback. The computer cannot detect the mobile phone in this mode, so I need advice on what to do next. Thanks
H0rajda said:
Hi, I need your advice please. Today I couldn't turn on my mobile phone (no update or something like that), so I tried recovery mode and it got stuck in loopback. The computer cannot detect the mobile phone in this mode, so I need advice on what to do next. Thanks
Click to expand...
Click to collapse
You're going to need to do this:
[GUIDE] REALME 7 RMX2155 GLOBAL BOOTLOADER UNLOCK
WELCOME, ALL. After a very tiring process of swapping between ROMs and changing regions, APKs, et cetera, we have finally been able to perfect the method for unlocking the bootloader of the RMX2155! This is a detailed guide aimed to give you an...
forum.xda-developers.com
If you do not want to unlock your bootloader, just follow from step one-to-ten inclusive. Don't follow beyond that if you do not wish to unlock your bootloader.
I have already solved this problem. It was enough to leave the mobile phone in a loop overnight before the mobile phone is discharged and then it is enough to turn on the mobile phone normally
H0rajda said:
I have already solved this problem. It was enough to leave the mobile phone in a loop overnight before the mobile phone is discharged and then it is enough to turn on the mobile phone normally
Click to expand...
Click to collapse
Sounds like water damage is causing your phone's power-button to stay held down. Happened to me with an Essential PH-1. You might want to look into getting a new phone, then.