ROM LLP6001 (New Firmware release)
This is a test and that will trip KNOX.... So you have been warned about all possible consequences. I am not responsible of anything that can happens to your device.
Please test and report.
I will try to update with new firmwares from Samsung but I am moving to MM with Temaseks CM 13 Rom, Multiwindows works well and Pen support is good, only miss SNote. I like MM very much and N will sure be great.... I don't think Samsung will update our tablet.
Latest firmware from Samsung P600XXUDPD1
Stock.
Deodexed.
Zipaligned.
Rooted.
BusyBox.
Init.d support.
Deknoxed.
Zipalign
Very Light Debloated, all that can be installed with Playstore has been removed.
Get rid of Setup Wizard After first boot you go directly to Home Screen.
SuperSU 2.67 beta that should patch Boot.
Multi Windows quad view.
Add new Power Menu need Xposed
Bugs:
Easy Chart FC
Dont forget to install languages to get Action Memo working and pen writing recognition.
Problem with SD card install Folder mount and run it, it will fix the issues
Backup you existing config with TWRP 2.8.7.0 on ExtSd card
(Flash stock rom with odin to get new bootloader) Not sure about that, should be tested on untouched 4.4.2 system and I dont have one as new SuperSU should patch the boot.img.
Flash TWRP (I recommend the last @joshdroid that allow touch screen to work. https://s.basketbuild.com/devs/Joshndroid/TWRP/lt03wifi).
Reboot in Recovery, Power off then push Power and volume up for 3 seconds, release buttons. Wait until TWRP load.
Factory reset and wipe all but SDext, format data.
Flash the ROM in recovery with TWRP 2.8.7.0. After flashing if TWRP ask to fix root, DO NOT INSTALL!
This is a beta version and should work fine with patched bootloader or unpatched bootloader but I am not sure, please report on success or failures.
Xposed beta version for 5.1.1 works perfectly.
Thanks to @joshdroid for TWRP with touchscreen
@SuperR for Kitchen
@karthikrr that lead the way for patched boot
and others that help testing
BTW: There is a test kernel Z1 by @xluco that works very well test 5.1.1 You can flash it with Flashify or TWRP
Downloads
Release
https://drive.google.com/file/d/0B99zLrJiOZzKU0xqOGo4cTZtcVU/view?usp=sharing
Thank you if you test it and report.
I will be the first one to try this. Will report back.
Can I reflash it directly on kitkat or first I need to install stock firmware via ODIN?
kornelius1982 said:
Can I reflash it directly on kitkat or first I need to install stock firmware via ODIN?
Click to expand...
Click to collapse
Directly.
Edit post
Not directly!
Flash bootloader first flashing 5.1.1 from Samsung with Odin.
Sent from my SM-P600 using Tapatalk
Woohoo! Can't wait to flash when I get home, daily driver has been cm and its so amazing but hate how the volume output of speaker and headset is low than stock.
I was on CM too and use volume booster. It is nice to get Notes and Multiwindows back and oficial LL is great for daily usage
Sent from my GT-I9505 using Tapatalk
Maby you can add the Tab A Apps to the ROM...? Btw, des sb else has this weird status bar bug, where the statusbar dissapperes when swiping down?
wulkanat said:
Maby you can add the Tab A Apps to the ROM...? Btw, des sb else has this weird status bar bug, where the statusbar dissapperes when swiping down?
Click to expand...
Click to collapse
Good point. I'm about the install those tab A apps and see what works and what doesn't.
Send pics
Sent from my SM-P600 using Tapatalk
Anyone tested working TWRP??
Any report yet?
Sent from my SM-P600 using Tapatalk
enotar said:
Directly.
Sent from my SM-P600 using Tapatalk
Click to expand...
Click to collapse
edit: nvm
Installing NAO!!!!!!
Of the Tab A apps fo far the video player, gallery app, and file manager are working. I'm attempting to unzip the ROM and add some of these apps again and reflash it. Will report back
EDIT 1: Splanner seems to be working just fine. The clock also works, but the stopwatch causes a force close. Still testing.
Anyone have problem where in twrp it says "unmount of /system failed: no such volume"
After i wipe cache and reboot its just a black screen
Before flashing factory reset, wipe all but external sd and format data. That should make it.
Sent from my SM-P600 using Tapatalk
I redownloaded the zip, factory reset and wiped everything in twrp still doesnt work
Ill try downloading official firmware and flash using twrp
yusoffb01 said:
I redownloaded the zip, factory reset and wiped everything in twrp still doesnt work
Ill try downloading official firmware and flash using twrp
Click to expand...
Click to collapse
It should flash, often you have to format data
What version of TWRP you have? Should be 2.8.7.0
Did you backup with TWRP on your SD ext card? If yes you can restore in TWRP
Did you format /data? writing yes when TWRP ask?
http://www.sammobile.com/firmwares/database/SM-P600/ with ODIN, there is no zip files now only my rom I think.
I have twrp 2870 I formated everything but internal storage. It flashed but after the Samsung boot screen the screen goes black and nothing happens after that. Is the latest firmware 4.4.2 for our device?
I dont know if you wait long enough. First boot is very long.5 10mn possible. Now if you are comming from 4.4.2 try to flash original 5.1.1 from Samsung with odin, flash TWRP and flash the rom.
Nobody report yet on flashing result bedide you.
Sent from my GT-I9505 using Tapatalk
Related
I just got myself a note 3 for sprint, and it had the OC5 Lollipop update on it. I flashed CF-Auto-Root on it, and it booted up fine. Used it for a bit, and then I tried putting TWRP on to flash Xposed Framework. TWRP flashed fine, and worked fine, but now the phone will not boot into the stock rooted rom. I have tried flashing the factory image again, that didn't fix it. Even tried flashing a kitkat factory image, and that didn't work either. The only way i can get the phone to boot into the OS is if i run a custom kitkat rom, and then everything seems to work fine. So where can i go from here to get the factory lollipop rooted with a custom recovery working?
tellem24 said:
I just got myself a note 3 for sprint, and it had the OC5 Lollipop update on it. I flashed CF-Auto-Root on it, and it booted up fine. Used it for a bit, and then I tried putting TWRP on to flash Xposed Framework. TWRP flashed fine, and worked fine, but now the phone will not boot into the stock rooted rom. I have tried flashing the factory image again, that didn't fix it. Even tried flashing a kitkat factory image, and that didn't work either. The only way i can get the phone to boot into the OS is if i run a custom kitkat rom, and then everything seems to work fine. So where can i go from here to get the factory lollipop rooted with a custom recovery working?
Click to expand...
Click to collapse
I'd say go back to NK4 and then accept the update to OC5 and root.
You'll need these files, please thank the OPs of the threads.
NK4 tar from [Odin] Mirrors for Official Samsung Tars for MJ4, NAB, NC5, NH7 & NK4
twrp-2.8.6.1-hltespr-4.4.img.tar from TWRP hltespr page
UPDATE-SuperSU-v2.46.zip from [STABLE][2015.02.13] SuperSU v2.46
Copy SuperSU zip file to your sdcard.
boot to recovery and factory reset, wipe partition cache and dalvik cache.
Then power the phone off from recovery.
Boot to download mode Volume Down + Home + Power ... then Volume Up.
(from the OFF state, booting into download mode from a ROM or recovery never works correctly when using odin)
Using Odin 3.09 flash NK4 tar, let it reboot, it will take it a while to start the first time.
when the phone restarts, unplug the usb cable.
you can skip all the setup stuff and then get the ota to get back to OC5; Settings, System Update, Firmware Update
once ota is completely done, power the phone off
go into download mode
odin the twrp tar (uncheck everything in odin)
once odin says pass unplug the usb cable and press Volume Up + Home + Power until the phone vibrates and you see the blue writing - this will get you into recovery w/o having to pull the battery.
flash the SuperSU zip file.
reboot to system, you should be on OC5 stock rooted.
jdelano said:
I'd say go back to NK4 and then accept the update to OC5 and root.
You'll need these files, please thank the OPs of the threads.
NK4 tar from [Odin] Mirrors for Official Samsung Tars for MJ4, NAB, NC5, NH7 & NK4
twrp-2.8.6.1-hltespr-4.4.img.tar from TWRP hltespr page
UPDATE-SuperSU-v2.46.zip from [STABLE][2015.02.13] SuperSU v2.46
Copy SuperSU zip file to your sdcard.
boot to recovery and factory reset, wipe partition cache and dalvik cache.
Then power the phone off from recovery.
Boot to download mode Volume Down + Home + Power ... then Volume Up.
(from the OFF state, booting into download mode from a ROM or recovery never works correctly when using odin)
Using Odin 3.09 flash NK4 tar, let it reboot, it will take it a while to start the first time.
when the phone restarts, unplug the usb cable.
you can skip all the setup stuff and then get the ota to get back to OC5; Settings, System Update, Firmware Update
once ota is completely done, power the phone off
go into download mode
odin the twrp tar (uncheck everything in odin)
once odin says pass unplug the usb cable and press Volume Up + Home + Power until the phone vibrates and you see the blue writing - this will get you into recovery w/o having to pull the battery.
flash the SuperSU zip file.
reboot to system, you should be on OC5 stock rooted.
Click to expand...
Click to collapse
Thanks! I actually got it working before i saw this by flashing the TWRP backup that someone posted on here, but i may try doing this to see if i can get xposed working with it, because it still isn't for me.
Not working
Everything working for me except when I flash twrp, it says pass, then comes to "android" recovery screen, so I can flash susuperuser
tellem24 said:
Thanks! I actually got it working before i saw this by flashing the TWRP backup that someone posted on here, but i may try doing this to see if i can get xposed working with it, because it still isn't for me.
Click to expand...
Click to collapse
Won't happen. It's all over xposed doesn't work on lollipop tw. Just search.
Sent from my 0x1 Note 3...... I love tep
Cybed said:
Everything working for me except when I flash twrp, it says pass, then comes to "android" recovery screen, so I can flash susuperuser
Click to expand...
Click to collapse
Try wiping data
Sent from my SM-N900P using XDA Free mobile app
kaos420 said:
Won't happen. It's all over xposed doesn't work on lollipop tw. Just search.
Sent from my 0x1 Note 3...... I love tep
Click to expand...
Click to collapse
Xposed will not work on 5.0 so don't try.... that is why you got a boot loop
jlechner said:
Try wiping data
Sent from my SM-N900P using XDA Free mobile app
Click to expand...
Click to collapse
Working now Tks
Chaz187 said:
Xposed will not work on 5.0 so don't try.... that is why you got a boot loop
Click to expand...
Click to collapse
did you mean to quote me? i know it wont work silly . i was telling him that.
kaos420 said:
did you mean to quote me? i know it wont work silly . i was telling him that.
Click to expand...
Click to collapse
Sorry quoted by accident
Chaz187 said:
Sorry quoted by accident
Click to expand...
Click to collapse
i forgive you but only when you drop a new rom lol
kaos420 said:
i forgive you but only when you drop a new rom lol
Click to expand...
Click to collapse
As soon as we get the base rom built it will come!!!!
[STOCK ROM][5.0] OD3 Android L Deodexed
Important Note:
This rom will not run unless you're already running a Lollipop bootloader!
This rom WILL run on both the OA6 and OD3 firmwares.
This stock rom is based on the OTA OD3 build.
DeOdexed Features:
- 100% Deodexed Lollipop Rom
- Rooted/SuperSU 2.45
- Busybox
- SQLite
- Knox Removed
- ItsOn Removed
- Connections Optimizer Removed
Downloads
Full Wipe and install the Full Tar first if not on Lollipop bootloader already!
See instructions below.
DeOdexed Download Link:
>> G900P_OD3_5.0.De-Odexed.Ver1.0.zip <<
MD5 Checksmum: 0f354d90d46ffc35c2a49e1eac40d13a
Important Note:
Initial boot takes a solid 10-15 minutes or more.
Flashing anything that requires optimizing apps (refreshing cache/dalvik cache) ups the (re)boot time to around 20 minutes.
Rom Installation:
- You must install a custom recovery to flash this rom.
- Install custom recovery with Odin. Recoveries & ODIN
(See instructions below to install custom recovery if you don't have it already.
- Reboot into recovery with Pwr/Home/Volume Up
- Full wipe
- Install rom with custom recovery
- OPTIONAL: Before rebooting, I highly recommend also flashing the Android L Debloat tool located at the bottom of this post.
Instructions to Install Recovery with Odin
• Download Odin v3.09 Recoveries & ODIN
• Extract Odin zip-file
• Power down the phone
• Open Odin v3.09
• Reboot phone in Download Mode (press and hold Home + Power + Volume Down buttons)
• Connect phone and wait until you get a blue sign in Odin
• Add the recovery file to AP / PDA (depending on version of Odin)
• Make sure re-partition & Auto Reboot are NOT ticked
• Click the start button.
• Unplug & Reboot phone in Recovery Mode (press and hold Home + Power + Volume Up buttons)
Changelog:
Code:
[B]OD3 deodexed V1.0[/B]
- Intitial Release
Known Issues:
- Google Maps force closes
Uninstall and reinstall from the Play Store
Kernels & Modems
SM-G900P Kernels
SM-G900P Modems
OD3 Hotspot mod
Download at bottom of this post
Note:
This is a framework edit.
Reboot time could be 15-20 minutes while it rebuilds cache.
.......
Great stuff as always TD!
Hotspot modification added to post #2 as an addon.
This can also be flashed right along with the rom during the same recovery session if this is your first time flashing the rom.
Clean install. Wiped everything. Factory reset before and after flash. Everything working fine minus Google maps? Soon as first boot before i could go through welcome setup maps force closed. After i signed into everything and looked around the rom a little i tried opening maps and it force closes doesn't even try to open? Everything else seems gravy so far
[email protected] said:
Clean install. Wiped everything. Factory reset before and after flash. Everything working fine minus Google maps? Soon as first boot before i could go through welcome setup maps force closed. After i signed into everything and looked around the rom a little i tried opening maps and it force closes doesn't even try to open? Everything else seems gravy so far
Click to expand...
Click to collapse
I'll check it out when I get time. Try uninstalling the app and reinstalling from the Play Store. If that works, I'll just add it as a known issue for now.
Will uninstall then reinstall and reboot then let you know. No worries. Just giving you heads up. You guys rock! Thanks for everything!!
[email protected] said:
Will uninstall then reinstall and reboot then let you know. No worries. Just giving you heads up. You guys rock! Thanks for everything!!
Click to expand...
Click to collapse
It looks like that worked so I added it to the OP under Known Issues.
Also, did you guys know that besides the Factory Reset Protection feature (not sure if it even works on this build), that the screen pinning feature is available in Settings/security?
It seems to work but I cant seem to exit pinning holding back/recents key like it tells you to do. Rebooting the phone seems to exit the pinned app is the only way I could clear the pinned app.
Yes. Uninstalling it and rebooting helped. It worked. And now maps works with no issues. So far everything else works as it should. I'll let you know any more issues or errors if i run into them. Thanks for all your hard work and dedication
I have a few questions. Do I install the Rom zip on internal or external SD card. And when do. I. Flash. The. Bloat. File in the. Process. And. Does. Mobil. Oden work. For. This
Question. How do I flash a custom recovery if already on od3? All attempts have failed through odin 3.10.
Would installing the hotspot mod remove the ability to update PRL and Profile via System Update? System Update seems to be missing completely.. Thanks!
garbage30 said:
I have a few questions. Do I install the Rom zip on internal or external SD card. And when do. I. Flash. The. Bloat. File in the. Process. And. Does. Mobil. Oden work. For. This
Click to expand...
Click to collapse
Doesn't matter which storage.
Odin does not flash zip files.
chromatica86 said:
Question. How do I flash a custom recovery if already on od3? All attempts have failed through odin 3.10.
Click to expand...
Click to collapse
Try a different version of odin.
If you're allowing it to auto reboot after flashing custom recovery, it wont work.
Follow the directions on the OP if you're not sure.
droidrage2010 said:
Would installing the hotspot mod remove the ability to update PRL and Profile via System Update? System Update seems to be missing completely.. Thanks!
Click to expand...
Click to collapse
No it shouldn't.
That's odd because that happens on some of the other lollipop roms too (system update missing).
No idea why it happens for some but not others. Maybe someone running this can say if they have it in their flash since I'm not running it at the moment.
So after I. Wipe. I. Update with the Rom zip? And the Rom will be the new os. Sorry I'm use to flashing tar files not updating with zips to get the Rom to work
garbage30 said:
So after I. Wipe. I. Update with the Rom zip? And the Rom will be the new os. Sorry I'm use to flashing tar files not updating with zips to get the Rom to work
Click to expand...
Click to collapse
Yes, that's pretty much it. If you have trouble with the rom, you might consider wiping internal storage too after saving whatever... and reflashing.
So don't unzip the file. 1 more question sorry. The page I found it on here said nothing about kernel or modem yet it had links at the bottom for the Rom. Do you. Know if they r included or do I need to update those too?
garbage30 said:
So don't unzip the file. 1 more question sorry. The page I found it on here said nothing about kernel or modem yet it had links at the bottom for the Rom. Do you. Know if they r included or do I need to update those too?
Click to expand...
Click to collapse
Don't unzip.
The extra links are just for reference.
ROM SM-P601 P601XXDOK4 (New Firmware release)
This will trip KNOX....
So you have been warned about all possible consequences. I am not responsible of anything that can happens to your device.
Please test and report.
Video Preview:
Latest firmware from Samsung P601XXDOK4 LL 5.1.1
Stock.
Deodexed.
Zipaligned.
Not Root ( to root flash SuperSU HERE )
FrameWork:
- 5 Way Reboot TW lollipop
SystemUI :
- Add new effects (WaterDroplet,SparklingBubbles,LensFlare,POPPINGCOLOURS )
- Mod quick icon Note 5 MM 6.0
- Recent bar trans
- Hide backup password text and icon.
Secsetting:
- Remove Power Saving Notification
- Change Modified device status to Normal
Touchwiz home:
- Note 5 icon mod ( folder, all app button)
- SoundAlive_20 support all bluetooth
- CSC tweak and mod
- Enable SD card write permittion
Backup FIRST
- Reboot in Recovery, Power off then push Power and volume up for 3 seconds, release buttons. Wait until TWRP load.
Factory reset and wipe all but Internal and SDcard.
Flash the ROM in recovery with TWRP 2.8.7.0. After flashing if TWRP ask to fix root, DO NOT INSTALL!
Downloads:
P601DOK4ModBinh24 Deoxed
AirCommand Note 5 _for_Note 10.1 2014 (Android 5.1.1)
Download HERE
PRESS THANKS NOW
After doing a full wipe (cache, dalvik cache, system, internal memory) and install, is stuck on black screen. and installing on another rom and doing the wipes, to start, multiple system applications are giving force close constantly.
This rom has the language PT-BR? If not, how can I add?
pcparaosamigos said:
After doing a full wipe (cache, dalvik cache, system, internal memory) and install, is stuck on black screen. and installing on another rom and doing the wipes, to start, multiple system applications are giving force close constantly.
This rom has the language PT-BR? If not, how can I add?
Click to expand...
Click to collapse
Flash stock P601XXDOK4 ROM then my ROM
TO enable PT-BR you can try to delete language.xml on system/csc
binh24 said:
Flash stock P601XXDOK4 ROM then my ROM
TO enable PT-BR you can try to delete language.xml on system/csc
Click to expand...
Click to collapse
You didn't explain the word "then" is it clean or dirty flash, anyway, I have tried both ways to flash your ROM.
1. Dirty Flash
The ROM was successfully flashed, but when I go for setting, it FC.
2. Clean Flash
It won't boot at all, stop on blank screen after Samsung logo.
I have tried both ways, without any mods, SuperSU or any additional apps. Thus, I believe, your ROM is conflicting with the original stock. This is almost the same as the other deodexed DOK4 ROM, while the DOJ5 ROM seems working nicely.
Perhaps it is better to play around with DOJ5 ROM instead of DOK4, or maybe you can find the error on future development. Thanks for your wonderful effort, your ROM surely looks better than the stock, just need some fixing. Keep up the work.
How To Flash This ROM + SuperSU
binh24 said:
Flash stock P601XXDOK4 ROM then my ROM
TO enable PT-BR you can try to delete language.xml on system/csc
Click to expand...
Click to collapse
binh24 said:
ROM SM-P601 P601XXDOK4 (New Firmware release)
This will trip KNOX....
So you have been warned about all possible consequences. I am not responsible of anything that can happens to your device.
Please test and report.
Video Preview:
Latest firmware from Samsung P601XXDOK4 LL 5.1.1
Stock.
Deodexed.
Zipaligned.
Not Root ( to root flash SuperSU HERE )
FrameWork:
- 5 Way Reboot TW lollipop
SystemUI :
- Add new effects (WaterDroplet,SparklingBubbles,LensFlare,POPPINGCOLOURS )
- Mod quick icon Note 5 MM 6.0
- Recent bar trans
- Hide backup password text and icon.
Secsetting:
- Remove Power Saving Notification
- Change Modified device status to Normal
Touchwiz home:
- Note 5 icon mod ( folder, all app button)
- SoundAlive_20 support all bluetooth
- CSC tweak and mod
- Enable SD card write permittion
Backup FIRST
- Reboot in Recovery, Power off then push Power and volume up for 3 seconds, release buttons. Wait until TWRP load.
Factory reset and wipe all but Internal and SDcard.
Flash the ROM in recovery with TWRP 2.8.7.0. After flashing if TWRP ask to fix root, DO NOT INSTALL!
Downloads:
P601DOK4ModBinh24 Deoxed
AirCommand Note 5 _for_Note 10.1 2014 (Android 5.1.1)
Download HERE
PRESS THANKS NOW
Click to expand...
Click to collapse
Finally I have succeeded to flash this good looking ROM on my SM-P601, these are the steps;
(Please follow and read properly)
-----------------------------------------------------------------------------------------------------------------
1. Download deodexed DOJ5 ROM from the next door thread (Official Deodexed)
2. As usual, put it on your SDCard
3. Boot into TWRP, for me, I use TWRP 2.8.76
4. Flash the deodexed DOJ5 ROM til its done (by default it will install SuperSU 2.52)
5. When DOJ5 is done, do clean dalvik and cache, just those 2 and no others
6. Then flash this modded DOK4 ROM and wait til its done
**Though this modded DOK4 is deodexed, it has no root access which it will conflict with the previous installed DOJ5 and it may cause boot failure or bootloop, thus, you need systemless SuperSU
7. Next is to flash SuperSU 2.66 (I haven't tried using CF AutoRoot)
8. When everything is complete, again do clean dalvik and cache
9. Boot to system without installing SuperSU from TWRP (it will ruin systemless SuperSU 2.66)
**REMEMBER TO NEVER INSTALL SUPERSU FROM TWRP IT WILL BREAK ROOT
--------------------------------------------------------------------------------------------------------------------
Result are shown by attached picture
1. Base ROM is DOK4
2. Baseband is DOJ4
3. Note 5 Icons and appearance
4. Root access
5. Ext SDCard access R/W
6. 5 ways on reboot menu (on restart option)
7. Camera is working
8. Latest Google Play
9. Updated Galaxy Apps
10. ViperFX Working
11. Air Command Working (Disable default air command if you wish to use this new looks)
That's all folks, enjoy the ROM and please be kind to say thank you on binh24' wonderful work for our beloved SM-P601.
Maaciiih cemuaaah...... Salam dari Jakarta
ghembuls said:
Finally I have succeeded to flash this good looking ROM on my SM-P601, these are the steps;
(Please follow and read properly)
-----------------------------------------------------------------------------------------------------------------
1. Download deodexed DOJ5 ROM from the next door thread (Official Deodexed)
2. As usual, put it on your SDCard
3. Boot into TWRP, for me, I use TWRP 2.8.76
4. Flash the deodexed DOJ5 ROM til its done (by default it will install SuperSU 2.52)
5. When DOJ5 is done, do clean dalvik and cache, just those 2 and no others
6. Then flash this modded DOK4 ROM and wait til its done
**Though this modded DOK4 is deodexed, it has no root access which it will conflict with the previous installed DOJ5 and it may cause boot failure or bootloop, thus, you need systemless SuperSU
7. Next is to flash SuperSU 2.66 (I haven't tried using CF AutoRoot)
8. When everything is complete, again do clean dalvik and cache
9. Boot to system without installing SuperSU from TWRP (it will ruin systemless SuperSU 2.66)
**REMEMBER TO NEVER INSTALL SUPERSU FROM TWRP IT WILL BREAK ROOT
--------------------------------------------------------------------------------------------------------------------
Result are shown by attached picture
1. Base ROM is DOK4
2. Baseband is DOJ4
3. Note 5 Icons and appearance
4. Root access
5. Ext SDCard access R/W
6. 5 ways on reboot menu (on restart option)
7. Camera is working
8. Latest Google Play
9. Updated Galaxy Apps
10. ViperFX Working
11. Air Command Working (Disable default air command if you wish to use this new looks)
That's all folks, enjoy the ROM and please be kind to say thank you on binh24' wonderful work for our beloved SM-P601.
Maaciiih cemuaaah...... Salam dari Jakarta
Click to expand...
Click to collapse
I really decided to try to make a rom deodexed and after breaking a bit the head, I made my first full, rom, deodexed rooted, debloated, although still have been useless applications each man to see. But gradually I am improving yourself. at the moment, my full testing rom p601xxudoj4 region SER. Working so far And normal. i would like to learn how to make mods, like the menu off with 5 functions. finally, one step at a time.
Has anyone tried to flash the air command alone? does it work?
ridicul0us said:
Has anyone tried to flash the air command alone? does it work?
Click to expand...
Click to collapse
It working for me
datdoan said:
It working for me
Click to expand...
Click to collapse
Hi, are you using P601XXDOK4 rom? I'm using P601ODDDOJ3 from India and I think it only works if I flash it with the lockscreen effect.
P601xxudok4
Stock rom cooked by me.
● Deodexed
● Debloated
● Rooted with new method that does not generate conflict with bootloader
● Fix external sdcard write
● All languages available
● Knox removed
⊙ advisable to do an installation clean. it may be that the screen is black in the part to choose the languages. turn off and turn on the screen that all back to normal.
● Link: https://drive.google.com/file/d/0B2a0geYLaY0oZ1VCT1BDeUFKbGM/view?usp=docslist_api
ridicul0us said:
Hi, are you using P601XXDOK4 rom? I'm using P601ODDDOJ3 from India and I think it only works if I flash it with the lockscreen effect.
Click to expand...
Click to collapse
yes, i using DOK4 ROM.
can i install this rom directly to P602? is this work?
stormy_ugur said:
can i install this rom directly to P602? is this work?
Click to expand...
Click to collapse
I do not know if will work. and they both p601 p602 possess the same hardware, but I do not have a problem with bootloader. you try if you have a way to restore your device in case of error.
This ROM look good. I am downloading.:laugh:
binh24 said:
ROM SM-P601 P601XXDOK4 (New Firmware release)
This will trip KNOX....
So you have been warned about all possible consequences. I am not responsible of anything that can happens to your device.
Please test and report.
Video Preview:
Latest firmware from Samsung P601XXDOK4 LL 5.1.1
Stock.
Deodexed.
Zipaligned.
Not Root ( to root flash SuperSU HERE )
FrameWork:
- 5 Way Reboot TW lollipop
SystemUI :
- Add new effects (WaterDroplet,SparklingBubbles,LensFlare,POPPINGCOLOURS )
- Mod quick icon Note 5 MM 6.0
- Recent bar trans
- Hide backup password text and icon.
Secsetting:
- Remove Power Saving Notification
- Change Modified device status to Normal
Touchwiz home:
- Note 5 icon mod ( folder, all app button)
- SoundAlive_20 support all bluetooth
- CSC tweak and mod
- Enable SD card write permittion
Backup FIRST
- Reboot in Recovery, Power off then push Power and volume up for 3 seconds, release buttons. Wait until TWRP load.
Factory reset and wipe all but Internal and SDcard.
Flash the ROM in recovery with TWRP 2.8.7.0. After flashing if TWRP ask to fix root, DO NOT INSTALL!
Downloads:
P601DOK4ModBinh24 Deoxed
AirCommand Note 5 _for_Note 10.1 2014 (Android 5.1.1)
Download HERE
PRESS THANKS NOW
Click to expand...
Click to collapse
successed install this Rom. but there are 2 problems :
1. always showup notification securitu notice
unauthorized actions have been detected. tap here for more information.
=> how to stop this notification??
2. air command
yes it works. but so sad the function isn't the same with note 5 function. for example : screen write. I cannot capture like note 5 do. wish it have note 5 function hehehe.
I know this is a little off topic but i didnt know whether or not to make a new topic so i thought I'd ask. I download the official 5.1.1 rom for P601 from sammobile. Thing is, its the Russian one (P601XXUDOJ2_P601SERDOJ2_SER) and mine is from South Africa (P601XXUCNJ1)
Will it work as normal on my device? I am not rooted
Sent from my SM-G925F using Tapatalk
timberland88 said:
I know this is a little off topic but i didnt know whether or not to make a new topic so i thought I'd ask. I download the official 5.1.1 rom for P601 from sammobile. Thing is, its the Russian one (P601XXUDOJ2_P601SERDOJ2_SER) and mine is from South Africa (P601XXUCNJ1)
Will it work as normal on my device? I am not rooted
Sent from my SM-G925F using Tapatalk
Click to expand...
Click to collapse
It should work without any problem
hope it can help
pippone121263 said:
It should work without any problem
hope it can help
Click to expand...
Click to collapse
Thanks for the feedback. Flashed it via Odin. Had some lag upon the first reboot but a factory reset solved the problem. Running very smooth
Sent from my SM-G925F using Tapatalk
timberland88 said:
Thanks for the feedback. Flashed it via Odin. Had some lag upon the first reboot but a factory reset solved the problem. Running very smooth
Sent from my SM-G925F using Tapatalk
Click to expand...
Click to collapse
Did you flash twrp after you flashed the rom. I am failing to get recovery flashed.
Sent from my SM-P601 using Tapatalk
s2mishappy said:
successed install this Rom. but there are 2 problems :
1. always showup notification securitu notice
unauthorized actions have been detected. tap here for more information.
=> how to stop this notification??
Click to expand...
Click to collapse
------Solution--------------------------------------
1. Install free "Package Disabler" Or 'Titanium BackUp' from Google Play Store.
2. Launch this app, search for "SecurityLogAgent".
3. Then disable/freeze it.
Do not do anything else. That's it.
Result: You will not see this annoying notification again.
Hi,
I'll try to keep latest TWRP by wzsx150, that are posted in MIUI Chinese forum here.
Downloads: Google drive
Latest: V3.3.0 April 21st
Changelog (translated):
v3.3.0 April 21st
1. Update to the latest 3.3.0 version, adjust and optimize
v3.2.3 April 1st
1. Update the built-in root to magisk-19.0, And other built-in feature upgrades
2. Other optimization adjustments
Finally. Thank you very much
edit : Can anyone install Magisk? Tried to install but no luck here
RinzImpulse said:
Finally. Thank you very much
edit : Can anyone install Magisk? Tried to install but no luck here
Click to expand...
Click to collapse
As seen on other forums Magisk v19 should work. Wipe Cache / Dalvik after installing...
Deep-Knight said:
As seen on other forums Magisk v19 should work. Wipe Cache / Dalvik after installing...
Click to expand...
Click to collapse
forget to update. yes, beta version works fine. forget that P only works with v19
Does it work with the Global version?
All 3 files seems to be for the China version.
Sent from my Mi 9 SE using Tapatalk
It works. CN just means the language and the origin. For some reason my data keeps getting encrypted after each reboot
can we perform backup and restore with this TWRP?
Tested backup of data, system and boot partitions working ok with 0421.
Haven't tested restore.
danielwright said:
Tested backup of data, system and boot partitions working ok with 0421.
Haven't tested restore.
Click to expand...
Click to collapse
+1
Yeah, I haven't tested restore too
Does anyone know of which files to make a backup from, in order to have a full working rom? There are so many files!
And what about this encryption tab in backup, what's that for?
Sent from my [device_name] using XDA-Developers Legacy app
putti71 said:
Does anyone know of which files to make a backup from, in order to have a full working rom? There are so many files!
And what about this encryption tab in backup, what's that for?
Sent from my [device_name] using XDA-Developers Legacy app
Click to expand...
Click to collapse
The encryption tab is an optional feature if you want to encrypt the backup files generated with a password - much like adding a password to a zip file.
For which partitions to backup to save a full working ROM - see https://twrp.me/faq/whattobackup.html however I haven't tested for MIUI 10/Android Pie on the 9SE.
Did someone successfully restore a backup made with this recovery?
For anyone having issues with flashing. Try disconnecting the cable after flashing and boot into recovery with power + vol up. I am running on stable eu rom with magisk now. Seems to work smoothly
decayed.cell said:
It works. CN just means the language and the origin. For some reason my data keeps getting encrypted after each reboot
Click to expand...
Click to collapse
Did you solve the problem? Cause I have the same on my Redmi 5 Plus and it's VERY annoying. I must format data everytime I want to flash a zip file, or I get an error message. I was planning to buy this phone but the lack of community support scares me quite a bit.
PurPLe SKy said:
Did you solve the problem? Cause I have the same on my Redmi 5 Plus and it's VERY annoying. I must format data everytime I want to flash a zip file, or I get an error message. I was planning to buy this phone but the lack of community support scares me quite a bit.
Click to expand...
Click to collapse
You just need to put in your PIN and it will decrypt
decayed.cell said:
You just need to put in your PIN and it will decrypt
Click to expand...
Click to collapse
But the recovery doesn't ask me for any pin or pattern.
I flashed twrp recovery and all seems good but when i try to boot into twrp there is always still the stock recovery. I tried also with 2 different fastboot but nothing changes. What i need to do ?
when the recovery is flashed, instead of rebooting device when in fastboot mode, just press vol+and power button
PeterImmel said:
Did someone successfully restore a backup made with this recovery?
Click to expand...
Click to collapse
Hi i would to known if restore works Fine?
PurPLe SKy said:
But the recovery doesn't ask me for any pin or pattern.
Click to expand...
Click to collapse
I boot up MIUI normally first. Then set a PIN, then reboot into fastboot and flash TWRP. After that I get a prompt
Instructions For Installing Pie Roms
Please Note This Is Not A Root Method For Oreo Or Pie. As Of Now There Is Still No Root Method For Oreo Or Pie. This Takes Some Patience To InstallNote8 SM-N950U/U1/W Install Instructions And Files
If you didnt upgrade to V8 bootloaders using odin. I recommend flashing full stock firmware with V8 bootloaders even if you are already on V8 bootloader via OTA update. I feel that maybe something in the OTA from V7 bootloaders to V8 may have corrupted a bootloader file and some people have experienced bricks with trying to update to V8 bootloaders from V7 using the below method so I recommend flashing full stock V8 firmware in Odin before trying this method and just understand there has been a risk of bricking device. Full stock can be found on Sammobile or updato or any other service you can find it. You will have to reroot of course. If you Updated to V8 bootloaders using odin method already then no need to do so again
Download
N950USQS8DVB1_SAFESTRAP.7z
Google_Pixel_Experience_Pie_8_Seriers.zip
Flash after you flash the system image above with a data wipe
After setup you need to set google dialer as default call app
Install Instructions Safestrap Method New Install Or Base Update
Make Sure The Latest Samsung Drivers Are Installed. They Can Be Found Here
You Must have safestrap installed to get safestrap follow the guide located below
Root And Safestrap For Note8 Up To V7 Bootloaders
1. If on V6 bootloaders before starting the process. If on V6 Pie rom reboot to download and flash the BL_N950USQS8DTG3_LEAVE_SAFESTRAP.tar.md5 then reboot this will put you on V8 bootloaders before starting
2. Copy SYSTEM_****.img to your internal sdcard. Reboot to safestrap In Safestrap choose install then choose select storage and select internal storage click ok then at bottom choose install image and choose SYSTEM_****.img then select flash to system image then swipe to flash. You can flash any mod zips at this time after you flash system image. Then in wipe tab chose wipe then advance wipe then wipe data
3. To leave safestrap reboot to bootloader or download from reboot tab.
4. In odin load BL_N950USQS7DTE5.tar.md5 in BL slot and
HOME_CSC_OYN_N950U_CACHE.tar.md5 in CSC slot flash phone will reboot to recovery and wipe cache then reboot
Instructions To Enter And Exit Safestrap After Initial Install. To Flash A Zip And Etc.
1. To enter safetrap flash the BL_RNTER_SAFESTRAP_N950UDTE5_V7.tar.md5 in BL Slot in odin phone will boot too safestrap sometimes it may take a minute to do so
2. To leave safestrap reboot to download from safestrap reboot menu
3. Use modded Odin and load BL_LEAVE_SAFESTRAP_N950UDTE5_V7.tar.md5 In BL Slot
Stock Rom Feature:
Debloated
SafeStrap Recovery PreLoaded
Safetynet Passes
Samsung Pay,Pass,Secure Folder Working
Native Hotspot Enabled
Multi User Support
CSC Files Decrypted
Click to expand...
Click to collapse
Mod Zips
SM_N950U_Mods_Safestrap_PIE.zip This will add call recording and a few other features to your csc
View attachment Adaway_Blocking_No_Root_Pie.zip
Install zip in safestrap
boot phone back up to system
you will have 2 apps in your apps drawer Host Adblocking and Stock Adblocking
too enable adblocking run the Host Adblocking app it may require rebooting phone to work
too disable adblocking run Stock Adblocking this probably will not require a reboot
what this does is move the system/etc/hosts file to the internal storage of your phone then I symliink the one in the internal storage to the system/etc/host file this way the file can be changed back and forth . If you would wipe data in stock recovery however you would need to reflash the zip in safetrap as a data wipe would delete the host file since it is now located on internal storage
Asking for clarity on the 80% bug. Is that bug only present if you are rooting the device? Is that a specific partition that gets modified that causes that bug that is only modified during the root process? Does this method without rooting the device also have the 80% bug with it?
Kind regards,
Cyrano
It's not a bug
Sent from my SM-N975U using Tapatalk
jlharmon001 said:
Asking for clarity on the 80% bug. Is that bug only present if you are rooting the device? Is that a specific partition that gets modified that causes that bug that is only modified during the root process? Does this method without rooting the device also have the 80% bug with it?
Kind regards,
Cyrano
Click to expand...
Click to collapse
It only has 80% charging capacity if running rooted nougat
Sent from some device I modified
jrkruse said:
Instructions For Installing Pie Roms
Click to expand...
Click to collapse
Been having issues with the N950USQS7DTA5_SAFESTRAP.rar filed in post #1. Doesn't unrar or unzip. Maybe it's just on my end but has anyone successfully used and accessed this file? I have tried downloading it twice to no avail.
EDIT: Looks like changing the version of 7zip I was initially using (version 19) to an older one (version 16) did the trick. No more unrar unzip issues.
What if you are already on the latest bootloader ? Also will I then be able to install an adbocker ?
zerokoo said:
What if you are already on the latest bootloader ? Also will I then be able to install an adbocker ?
Click to expand...
Click to collapse
How do you find BL version?
Is this the only Pie rom for the N950U? Thanks
SkOrPn said:
How do you find BL version?
Is this the only Pie rom for the N950U? Thanks
Click to expand...
Click to collapse
5th number to the left of the very last number of build number
Sent from some device I modified
zerokoo said:
What if you are already on the latest bootloader ? Also will I then be able to install an adbocker ?
Click to expand...
Click to collapse
Once you get safestrap installed you can start on number 2 in the directions but its fine to do step 1 even if you are on latest bootloader. I do have an adblock for non rooted pie rom
Sent from some device I modified
SkOrPn said:
How do you find BL version?
Is this the only Pie rom for the N950U? Thanks
Click to expand...
Click to collapse
Go to software information in setting it will show you
<strikethrough>If on rooted nougat rom, wanting to go to pie from here, need to wipe / factory reset first before ODIN step? </strikethrough>
Actually, please confirm since I was running stock pie on BL7, and now I am on rooted nougat, all I need to do is reboot to safestrap, and wipe data / factory reset and then flash the DTA5_system.img .
Thanks for all this ... miss the flashing days.
marcjc said:
<strikethrough>If on rooted nougat rom, wanting to go to pie from here, need to wipe / factory reset first before ODIN step? </strikethrough>
Actually, please confirm since I was running stock pie on BL7, and now I am on rooted nougat, all I need to do is reboot to safestrap, and wipe data / factory reset and then flash the DTA5_system.img .
Thanks for all this ... miss the flashing days.
Click to expand...
Click to collapse
Flash system image then wipe then flash the BL file and csc files in odin after leaving safestrap. Then when phone reboots too stock recovery wipe cache then reboot to setup
Sent from some device I modified
jrkruse said:
Flash system image then wipe then flash the BL file and csc files in odin after leaving safestrap. Then when phone reboots too stock recovery wipe cache then reboot to setup
Sent from some device I modified
Click to expand...
Click to collapse
Worked great.... all good... thank you!
marcjc said:
Worked great.... all good... thank you!
Click to expand...
Click to collapse
I’ll post some zips that can be flashed that will give you some add blocking and some csc mods like call recording and several other things
Sent from some device I modified
jrkruse said:
I’ll post some zips that can be flashed that will give you some add blocking and some csc mods like call recording and several other things
Sent from some device I modified
Click to expand...
Click to collapse
Great... Looking forward to it.. thanks again!
Sent from my SM-N950U using Tapatalk
So i downloaded and installed this and it works great but.....whats the point of installing this if i lose root, didnt read that at the top of the post before i did this? also i need to disable knox if anyone could help me with that id appreciate it.
JonandRoid said:
So i downloaded and installed this and it works great but.....whats the point of installing this if i lose root, didnt read that at the top of the post before i did this? also i need to disable knox if anyone could help me with that id appreciate it.
Click to expand...
Click to collapse
If you want root you have to use the rooted nougat rom in the root thread. This rom is not rooted but still has safestrap so you can still flash mod zips and delete system apps. So why do you need to disable knox? I mean on this rom you could delete it if you want but that will break Samsung pay and pass
Sent from some device I modified
I tried this rom. Removed samsung camera pie app, install a nougat camera app which i like but it won't work, which for me is deal breaker on this pie rom. The camera is always top priority feature on phone these days.
There's something very very special about camera app that samsung want to control it and its quality and we can never revert back to its original quality in android 7.1.1 even with some "hacking" like this. why make things so hard then i will make thing hard to buy you
Thank you for your work but i am afraid i use samsung phone again
gamechangervn said:
I tried this rom. Removed samsung camera pie app, install a nougat camera app which i like but it won't work, which for me is deal breaker on this pie rom. The camera is always top priority feature on phone these days.
There's something very very special about camera app that samsung want to control it and its quality and we can never revert back to its original quality in android 7.1.1 even with some "hacking" like this. why make things so hard then i will make thing hard to buy you
Thank you for your work but i am afraid i use samsung phone again
Click to expand...
Click to collapse
You can try one of the gcam modded to work on this phone
Sent from some device I modified