Hello. I am pretty devestated this morning. Mid last week I bought a Sony Xperia Z2 Tablet. Spent quite a bit on it. Put it in a case, and had a screen protector on it. Though last night it had fallen from the side onto the floor about 3 foot and despite the protection it now has a crack on the screen. The LCD is fine. No problems with it. Though the touch is a bit messed up. It will only notice the touches at the bottom. It's now unusable.
I have been looking everywhere for a replacement digitizer but u can only seem to find a replacement glass with the lcd screen. Costing around £200. Where as I just need the glass.
The z1 tablet glass is around £30 and I believe it may be the same... can anyone confirm? Or will the z1 glass not work with my z2 tablwt. I think they're both the same size... 10.1 ?
Really stuck with what to do here... don't want to be paying £200 to get this fixed.
Did you ever have any luck doing this? I've managed to do the same thing and am now wondering if the z1 replacement will work. Thanks!
Sent from my stupid iPad using Tapatalk
hannaway1990 said:
Hello. I am pretty devestated this morning. Mid last week I bought a Sony Xperia Z2 Tablet. Spent quite a bit on it. Put it in a case, and had a screen protector on it. Though last night it had fallen from the side onto the floor about 3 foot and despite the protection it now has a crack on the screen. The LCD is fine. No problems with it. Though the touch is a bit messed up. It will only notice the touches at the bottom. It's now unusable.
I have been looking everywhere for a replacement digitizer but u can only seem to find a replacement glass with the lcd screen. Costing around £200. Where as I just need the glass.
The z1 tablet glass is around £30 and I believe it may be the same... can anyone confirm? Or will the z1 glass not work with my z2 tablwt. I think they're both the same size... 10.1 ?
Really stuck with what to do here... don't want to be paying £200 to get this fixed.
Click to expand...
Click to collapse
You should have very specific equipment for the replacing digitizer on the LCD, better and easy way buy complete set for replacing.
i did this on my z2. It was not as advertised....... the best approach is to by the full LCD and Glass assembly. To remove the old assembley you will need to heat the glass significantly to soften the adhesive. Even then, it will most likely shatter. Dont worry.... you dont need it. Chip, scrape, pull it all off the frame being careful not to damage any of the bezel or the underlying components. Then once all is off, take some goof off and remove all the old adhesive. Then put some new aadhesive or thin double sided tape in the frame track and then reset the new LCD assembley. Prior to that though, verify it works first as getting it back off may shatter the glass again.
Not to tough as long as you have the full assembley to reinstall......
Related
Okay so I am sharing my experience for everyone. I had recently broken my screen, and I needed to replace the screen. I bought a screen digitizer off of eBay, and....Destroyed the phone sub frame. The reason I am posting is because I am warning all of you, you need to buy a full display assembly online. This includes the whole new display( glass and LCD) wires and bits, and a full subframe. Unless you are superior to an Asian 12 year old working in the factory that made your phone (hint hint, wink wink, you're not) than you need to buy a full assembly, or end up like me an destroy your phone.
Sent from my Amazon Kindle Fire HD using Tapatalk HD
+1.
Unfortunately, I saw this post after doing damage to my phone. The plastic housing that the digitizer /lcd sits in is verrrryyy easy to damage around the edges when you try to separate the screen. Heating it with the heat gun to get the separation actually makes it even more fragile and prone to damage. Thankfully I was able to return digitizer/lcd and get full setup from here :
http://www.etradesupply.com/oem-htc-evo-4g-lte-lcd-screen-and-digitizer-assembly-with-front-housing-and-light-guide.html
Hopefully things will go a little better this time.
Wow, that includes the plastic frame? I replaced my screen a couple of weeks ago (glass and LCD), and the edges of the frame did get slightly chewed up. It's not too bad, but I wish I had known abut this item.
On a positive note, I suppose I can get a job in China when the economy completely collapses.
Sent from my Nexus 7 using xda app-developers app
Ya my screen got waterlogged after I got trashed and left it out in the rain. Let everything dry out and thankfully all the boards and connectors work. I ended up going the cheap route and just buying a screen and not the frame. I almost successfully got the thing apart. I do have a small chip in the frame on the left side but my case covers that. I only paid around $50 but I did give myself around $50 in headaches. Definitely spend the extra $50 and just get the whole package.
If you do decide to try and separate the screen from the frame, use a lot of heat. Not necessarily high heat, but for a good duration. Get the adhesive nice and warm. Then pry it loose through one of the holes in the housing/frame (go at it from the back) and slowly work it away from the frame. Once you get it off, heat the adhesive back up and then add some 5 minute quick epoxy to the black adhesive pads in the frame. Then use some clamps and let the epoxy cure. There is a great video I followed below. It took me a while and I will probably ride with this for a minute until it bothers the hell out of me. My gf said she can't even notice.
https://www.youtube.com/watch?v=Ae52Ug8vFwA
case screen cover plastic sheet work?
I'm just wondering how many naked phones get broke compared to well protected?
Gnexd said:
I'm just wondering how many naked phones get broke compared to well protected?
Click to expand...
Click to collapse
I have a Incipio NGP case on mine all the time and I always have a screen protector installed (usually the cheap ones from Amazon). I have never had a problem with the screen until I left my phone out in the rain. The Gorilla Glass II is decently strong but only to a certain extent. I mainly use the screen protector from scratches if I accidentally put it in the same pocket as my keys.
I was afraid of breaking mine one day, fortunately for me my volume button went out first and I have Best Buys insurance and the replace the phone with no deductible.
Seems like screen issues are pretty common on this model. I'm on my 4th Evo now because the screen kept failing on me. Based on what I read it sounds like I'd never want to have to replace this myself.
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
The likelihood the digitizer isn't cracked is very low.
NABI2 touchscreen layering:
front glass..............thick (glue around outer most edges to frame)
airgap......................very thin (glue around edges)
digitizer glass........thin
lcd............................thick
I tried the same thing but the actual digitizer glass is like 1/10 the thickness of the front panel glass and glued to it on the edges. If the digitizer glass is not cracked, it will probably crack on attempted removal from the front panel. If the digitizer is fully working in-spite of the front glass cracking it may be possible to heat the front assembly up to the point the adhesive allows the glass to just fall out.... but as far as how close the glue melting point is to the melting point of the plastic frame is not something I know. The entire assembly is put together with some super strong double-sided sticky tape. If you can source just the digitizer and glass assembly I'd like to know.
Once one attempts a replacement and it doesn't work is it still possible to get Fuhu/Nabi to replace the screen (at reasonable cost)?
( If not you could just plug in a keyboard/mouse and use the hdmi out... would make a great XBMC server... once the port exists... )
.
Pictures?
oranrene7 said:
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
Click to expand...
Click to collapse
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
manx_73 said:
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
Click to expand...
Click to collapse
I already put it back together because he was taking everyone's iPhones to play games on. lol The glass anatomizer (or whatever it's called), had a long thin strip and the LCD had a thicker one. Either way, the glass nowhere near fit. I had a feeling it was going to be too hard to replace anyway; hence the reason I can't seem to find a tutorial on fixing a Nabi.
And yes, Fuhu will fix it for like 85 bucks plus shipping...I only paid 90 for the tablet just recently (Craigslist). Oh well. I guess we'll just let him play till he cuts his finger.
Thank you both so much for your input. I appreciate it
Help replacing Nabi2 digitizer screen...
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
ChipStewart said:
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
Click to expand...
Click to collapse
I am also looking for the same digitizer model any luck? Anyone?
brianbri6 said:
I am also looking for the same digitizer model any luck? Anyone?
Click to expand...
Click to collapse
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
rex.torres said:
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
Click to expand...
Click to collapse
I am looking at a few on Fleabay now. You need to take yours apart and compare model numbers with the ones on Ebay. Just search ebay for Nabi 2 digitizer. about 20 results for it, ranging from $25 -65. The $65 one is a complete front panel minus the LCD. just unscrew the top panel and replace, it looks like.
Wow...I'm the original poster...and here I am years later still bothering with Nabi! lol In 2014, I went on Nabi's site and paid $60 to have the digitizer replaced. I never sent the Nabi in because a friend of mine gave me his kid's Nabi to use for parts (he couldn't get it to charge any longer). I took the entire front panel with LCD and digitizer and replaced it with mine. Worked like a charm...until my younger son stepped on it...on purpose! Lil turd! So, here I am again trying to fix the screen, BUT, this time I noted that I needed the LCD and the digitizer (the ribbon on the LCD was breaking off - not sure how that could have happened). At any rate, I ordered both the digitizer and LCD. I replaced them both and it's a no-go...not working. I still have it apart, but I have the cables plugged in, so when I move the screen around, the Nabi screen will come up, but the touchscreen isn't working. I may be sending the digitizer back, but I'm wondering if it's because of how they are lying on one another. Does anyone know if maybe the touchscreen doesn't work if it's too close or too far from the LCD screen. I don't mean by an obvious amount - I mean is there a "specific" amount of space. I am trying to get it in the casing exactly like it was before, but I don't want to do anything permanent until I know it's working 100%.
Also, you can easily and cheaply get the LCD and digitizer for the Nabi now - just stinks you have to order it from China and it takes forever to get here! I can only imagine how long a return/replacement is going to take. Ugh!
Oh, and Nabi has yet to return my $60 bucks...I have spent way too much on this tablet!
I ended up having to match my part number to a used but good part off of ebay. I had ordered several "new" digitizers and they never worked. There seemed to have been a design change somewhere along the line, or some missing information that made mine not work with the "new" parts available at the time.
However, to answer your question, the digitizer will work completely separated from the LCD as long as the ribbon cable is attached (of course). Rather than reassembling everything, I would only connect the digitizer to see if it worked. When I finally found one that worked, I then committed to doing the full repair.
It was a very painful process.
Is it an easy thing to take apart and put bk together if you have never done this before my daughter stood on her Nabi accident it was under her comfort blankie opps screen cracked but works fine she's only 2 ( well advanced for her age) soI dnt want her to use it incase she cuts her tiny fingers doesn't feel sharp but dnt want to risk it can't find any view on u tube still many years on be nice if someone would do one haha
Honestly...
It was a pain in the ass to remove the glass / digitizer from the nabi. If you're not careful--as I was--it is real easy to deform the plastic bezel that the glass / digitizer and LCD reside in. I ended up having to buy a replacement bezel that already had a digitizer and LCD attached to it. The LCD was DOA, but the one from my original was fine, so I begrudgingly transplanted that too.
Test the digitizer FIRST before committing to installing it on the plastic bezel.
i recently dropped my phone and it got a crack in the bottom right corner around the back button stretching up to the middle of the left hand side of the screen, and i need help repairing it.
Im not sure if i can just replace the glass myself or i need to replace the digitizer or any other parts as the screen and back button still work perfectly fine.
I'd also like to know whether this job is easy enough to do at home as i am on a low budget, however i dont have much experience fixing phones.
much appreciated if anyone can help me
Replace the screen assembly, glass plus digitiser and oled screen. Trying to unglue the glass is very hard and the heat can kill the phone.
boomboomer said:
Replace the screen assembly, glass plus digitiser and oled screen. Trying to unglue the glass is very hard and the heat can kill the phone.
Click to expand...
Click to collapse
Replacing the whole digitiser is a lot easier, but beware cheap(ish) ebay parts - I replaced my digitiser with an assembly from ebay, but the glass in the replacement broke very easily.... replaced it again and it's cracked again, without even having a hard knock. Nowehere near as sturdy as OEM parts. Screen still works so leaving it for now
Words of warning...
I attempted to replace the glass on my S3 after I dropped it. I have over 20 years experience as a computer engineer and access to loads of tools. I watched numerous YouTube videos on the process before I started yet still I managed to break the digitiser. In the end I bit the bullet and bought another brand new S3 for £200. The cheapo replacement glass I bought from eBay did not seem very sturdy either - I'm certain it's not gorilla glass. My advice would be to get it fixed professionally by someone who uses OEM parts but then again, how close in price would that be to a brand new phone?
Hi Guys,
i think the most of you know, that the Z2 has a really poor glass quality. (My phone fell down from about 30 CM to a carpet and the screen had a little crack and the touchscreen didn't work. (Insurance of my friend payed for this, because he has thrown it down)
The costs for the repair were 200 €!
Now i found this on ebay: http://www.ebay.de/itm/Orig-Sony-XP...zer_Ersatzteile_Werkzeuge&hash=item3a9f2231e3
It was sold 53 times, but i thought you can't replace only the glass?
Or is it possible?
No, dont try it, I already bought one of them but at the end I experienced that the glass and lcd display is sticked to each other and not seperable.
I had to buy another one with lcd+glass and was able to fix.
They are selling but its a fault, we do not have factories to combine those glasses with lcd. They are cheating, be careful.
It‘s a incell screen so can't be separated
Glass and screen are seperate on Z2 from what i saw when i disasembled my phone.
Envious_Data said:
Glass and screen are seperate on Z2 from what i saw when i disasembled my phone.
Click to expand...
Click to collapse
On my D6503 glass/digitizer/lcd was glued together. Changed display recently because of a tiny fall.
But atleast its fairly easy to change.
I assume my lovely daughter has dropped or knocked the tablet as I have a diagonal hairline crack across one corner. Doesn't affect use but its bugging the hell out of me!
So I understand to get it repaired is going to cost more than £300 (local shop). I could get a new one for £400! Or should I just sit on it (not literally) and wait for the S4 - missed MWC so expect after August now.
Even with this damage I'd expect to get over £150 for it on ebay so maybe not really worth doing anything.
Anyone else (UK) had a screen replaced?
bonerp said:
I assume my lovely daughter has dropped or knocked the tablet as I have a diagonal hairline crack across one corner. Doesn't affect use but its bugging the hell out of me!
So I understand to get it repaired is going to cost more than £300 (local shop). I could get a new one for £400! Or should I just sit on it (not literally) and wait for the S4 - missed MWC so expect after August now.
Even with this damage I'd expect to get over £150 for it on ebay so maybe not really worth doing anything.
Anyone else (UK) had a screen replaced?
Click to expand...
Click to collapse
When my son did this to his tablet I just put a screen protector over the screen and it was good as new. Obviously still cracked underneath.
its safer to put on a tempered glass protector and it take the bump.. than be penitent after the screen has cracked. also better to invest in a bumper cover. I learnt it the hard way with my Tab S 8".. spent INR 10k to get it repaired and another 2K for a book case. had i invested in a book case, i would have saved 8K!
Tab S3 has a hard case... bulky, but then i got big hands
snakez23 said:
its safer to put on a tempered glass protector and it take the bump.. than be penitent after the screen has cracked. also better to invest in a bumper cover. I learnt it the hard way with my Tab S 8".. spent INR 10k to get it repaired and another 2K for a book case. had i invested in a book case, i would have saved 8K!
Tab S3 has a hard case... bulky, but then i got big hands
Click to expand...
Click to collapse
I agree with a case but not a screen protector. Totally ruins the experience. I don't want to keep the screen in pristine condition for someone else's benefit. I want to experience a smooth silky touch screen for myself.