Related
I have a ton of micro-USB chargers that I've used with my GNex and Evo3D with no issue. The only consideration I take into account is Amperage, and I toss the ones below 800 mAh. Last night I plugged into one thats around 850 mAh and left my phone to charge all night (at around 5%). When I woke up, the phone had completely discharged without any sort of recharge.
Since this isn't a Nexus phone, am I locked in to only using verizon branded chargers? Is there a way to defeat that with root?
I haven't had any issues with that as I use all different types. Maybe just try another or maybe it wasn't plugged in all the way.
What voltage is it rated at? It could be that or that the charger is bad somehow. I charge mine nightly with a .7A charger and it's always been full when I wake up (about 30-50% when I go to sleep).
I have the sprint note 2 but they are essentially the same phone so here is what Igot for you:
there is no "smart" element to any chargers in the market, so your phone shouldn't know the difference between Verizon brand and the devil's own brand
if you look at the stock charger it outputs 2 amps...the phone needs this and in my experience it needs at least 1 amp in order to charge instead of discharging slower
also there is a known issue with all note 2s that the cable will not sit snugly inside the port causing it to be a bad connection... just make sure you put it in hard (no pun intended) and it shouldn't be a problem
Sent from my SPH-L900 using xda app-developers app
Sent from my SPH-L900 using xda app-developers app
Yeah, if you take a close look at the micro-usb port, it is recessed a bit. Make sure you plug the cable in firmly.
reinaldistic said:
also there is a known issue with all note 2s that the cable will not sit snugly inside the port causing it to be a bad connection... just make sure you put it in hard (no pun intended) and it shouldn't be a problem
Click to expand...
Click to collapse
I think this was likely the issue. The charger is rated at 1 Amp, and I tried it out again last night and it appeared to work for the few seconds I had it plugged in, so I must not have had it in there snugly.
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
apols said:
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
Click to expand...
Click to collapse
I don't remember where, but I remember reading about someone with this issue where they were using their phone as a gps while charging it and it died. Someone commented saying that the culprit was probably a faulty charger. Sounds like they were right.
apols said:
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
Click to expand...
Click to collapse
I have seen this same thing with two Droid X's plugged into the same 2A charger. One phone would charge and the other would do exactly as you describe. It didn't do it all the time, it just depended on how low the battery levels were on each device. How much battery life do you have left when it does this? You may just need to use a higher amperage charger.
I have not received my Note II yet, but it sucks that I will most likely not be able to charge it while tethered (USB) to my laptop.
Based on the info I could find (kernel driver), the phone will accept up to 650mA of power, so anything over that should charge the phone at the same rate. Voltage shouldn't be an issue as it is charging via USB, which is 5V (+/- 5%). Unless someone has an amp probe to put on it, we can't tell if it is actually pulling more or less than what the driver specifies. And, as someone else stated, the phone can't tell if you're using a genuine Samsung cable and charger, or a $1.00 made in China cable/charger, as long as they both output the same voltage/amperage, the phone will never know the difference.
Based on what you said though, if the phone is constantly seeing the charger connect/disconnect, that would drain the battery even faster.
Amazing offer got myself QiStone power bank for my Nexus 6 also have deals for Samsung S5 and Note 4 options:
http://fonesalesman.com/pages/black-friday-deals
got email from em last night
https://www.youtube.com/watch?v=QIkZUa7Cwec
i picked up two of the stones. they charge the nex 6 pretty quick--wise choice.
when the phone is off, does this charger turn the phone on when charging? it's a pretty annoying thing on my nokia Qi charger. it never did this with my nexus 5, only the n6
if directed to me, i never turn off the phone so cant comment.
i THINK i have read on this site that the nex 6 , if off and put on wireless charge, will turn on the phone. maybe its not specific to any one charger...
indianajonze said:
when the phone is off, does this charger turn the phone on when charging? it's a pretty annoying thing on my nokia Qi charger. it never did this with my nexus 5, only the n6
Click to expand...
Click to collapse
I use the Tylt VU for wireless charging. However I can confirm for me personally my N6 does not stay in its "awake" status while charging. I do however have my N6 go into daydream mode while charging. QI works very well for the most part. As discussed in a totally different thread but, be aware, for whatever reason after it goes to a full charge with QI daydream stops as well as charging altogether. From what I have observed personally, there is no trickle or slow charge being performed when charging reaches 100%, nor does the QI kick back in (which would be annoying in a sense) when it drops 1%. However I've had the N6 for about two weeks and never had any issues with it being below 100% when I wake. Just an observation and something to consider.
Sent from my Nexus 6
Curious if any QI chargers trickle charge like USB connection vs switching on and off constantly
bob2300nx said:
Curious if any QI chargers trickle charge like USB connection vs switching on and off constantly
Click to expand...
Click to collapse
For sure I know that the Tylt Vu isn't trickle charging too well. It gets to 100%, when it decreases, it charges again. So I constantly hear the charge sound again.
Powerbot round does not
So I guess no QI chargers trickle?
Ended up going with this, was 11.99 with prime:
http://www.amazon.com/gp/product/B00LFVPVHK/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Choe does trickle charge
The issue is with the Nexus 6 refusing to trickle charge on qi for whatever reason.
cmh714 said:
Choe does trickle charge
Click to expand...
Click to collapse
my95z34 said:
The issue is with the Nexus 6 refusing to trickle charge on qi for whatever reason.
Click to expand...
Click to collapse
Getting mixed signals over here. I wonder who is right?
bob2300nx said:
So I guess no QI chargers trickle?
Ended up going with this, was 11.99 with prime:
http://www.amazon.com/gp/product/B00LFVPVHK/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Click to expand...
Click to collapse
I think the misspelled Italian that should be red flag.
dligon said:
I think the misspelled Italian that should be red flag.
Click to expand...
Click to collapse
Actually if you check the reviews on here and amazon, they are pretty good. These chargers aren't that complicated, no point in paying more.
bob2300nx said:
Actually if you check the reviews on here and amazon, they are pretty good. These chargers aren't that complicated, no point in paying more.
Click to expand...
Click to collapse
True you only pay more for extra coils the name brand and possible quality build.
Nexus 4 orb
The nexus 4 orb charger works great with the Nexus 6. Charges to 100%, stops, then starts up again at around 96%. However, this stop/start charging cycle does not make any noise.
I did notice early on that my Nexus 6 would hit 100% charge, then completely stop. This was on a custom kernel (Franco), but once I replaced that with a different kernel (leanKernel), wireless charging started behaving properly again.
the Choe keeps it at 99 or 100, basically always charging....no extra sounds here either...IMHO works great.
and through a Ringke Fusion case
My question is this something to do with the nexus or all QI phones in general? Do they normally goto trickle charge? If so google should fix this, id imagine this cant be good for the battery actually really bad for the battery. Going really low or really high wears the battery more than keeping it in more of the ~30-80 range. Yo-yoing like that cant be good for the battery.
I have these too coming, will update with how they work
http://www.amazon.com/gp/product/B00S7IKRK0/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
http://www.amazon.com/gp/product/B00LFVPVHK/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Both for $38 shipped
I have a qifull wireless car charger and on rides home from work when battery is at about %50, my phone temp will go up to 120-130f. This is with Franco Kernel set to Power Saving Mode, and even with the screen off. It's always done this with different kernels ect... I read somewhere that this can happen if the phone is not able to properly align with the coils?
Qifull QC2015 3-Coils Qi Wireless Car Charger Dock with One Touch S... http://www.amazon.com/dp/B00OFQXEKS/ref=cm_sw_r_udp_awd_Qfzcvb1P7WG53
Sent from my Nexus 6
My current wireless charger will charge my phone to 100% and then quit for the rest of the night, leaving my phone at around 95% when I wake up. Is there a better charger to remedy this?
I went back to a Kidigi wired charger to get around that. I rely on the clock feature of the dock, so that was a real turnoff for me.
Tylt Vu, 100% every morning.
Using the Incipio Ghost 100 from when I had my DNA. Works perfect.
http://www.amazon.com/gp/product/B00LE6X5VU?keywords=qi charger&qid=1455841206&ref_=sr_1_11&sr=8-11
Ive been using it for over a year, always at 100% in the morning.
I've been using the Choe stadium charger I like it so much I got a second for the office.
Nokia DT-900.
Bonus is that this dock, which was originally around $60, can be found for about $15 on the third party market now...
what's wrong with the turbo charger that it shipped with?
buschris said:
what's wrong with the turbo charger that it shipped with?
Click to expand...
Click to collapse
its not wireless
three west said:
Tylt Vu, 100% every morning.
Click to expand...
Click to collapse
+1 for Tylt Vu
Also have the Spigen wireless charger that you have to use with your stock charger. It works great most of the time, but occasionally it'll stop working and needs to be unplugged/replugged back in.
no charger is "wireless". What I meant was, is your charging pad plugged to the stock turbo charger and stock cable?
I am using the EXILIENT CHARGING PLATE
SAME WITH ME BUT ON THE BRIGHT SIDE IT SAVES YOUR BATTERY FROM OVERCHARGING AND HEATING, moreover if you use quick charger with the charging plate you get full within 3 hours!!! ain't BAD.:good:
Another vote for the tylt vu. It technically stops charging, but my phone is always at 100% when I pick it up. It does turn off the charging light, but I am assuming that is to keep it from cooking a battery.
Sent from my Nexus 6 using Tapatalk
bluefalcon13 said:
Another vote for the tylt vu. It technically stops charging, but my phone is always at 100% when I pick it up. It does turn off the charging light, but I am assuming that is to keep it from cooking a battery.
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
I've settled on the Vu as well. It stops charging once the battery is full (a few mins after the phone registers 100%). If the battery dips back down to 99% during idle, it kicks back on and tops the battery off back to 100% and turns off again.
The Vu is my fav charging stand because it doesn't have bright, obnoxious charging LED indicators. Just a nice dim green LED that doesn't light up my entire room at night.
amanamarsingh said:
IT SAVES YOUR BATTERY FROM OVERCHARGING AND HEATING
Click to expand...
Click to collapse
The charging rate is controlled by the handset, not by the charger, so it is not possible to "overcharge" your battery.
It is also extremely unlikely that any increase in temperature from charging will cause any deleterious effect to the battery - this will have been taken into account as part of the design of the charging circuit.
The TYLT VU is good, but it's $50.
The Nokia DT-900 is just as good a charger, and on the third party market it's now about $15.
Your choice...but I can think of other things to do with $35 than give it to TYLT.
quadcrap1 said:
Nokia DT-900.
Bonus is that this dock, which was originally around $60, can be found for about $15 on the third party market now...
Click to expand...
Click to collapse
That's the charger I use and it's great
It is not the wireless charger stops charging. It's the software in the phone that shuts off the charging.
Philip said:
The charging rate is controlled by the handset, not by the charger, so it is not possible to "overcharge" your battery.
It is also extremely unlikely that any increase in temperature from charging will cause any deleterious effect to the battery - this will have been taken into account as part of the design of the charging circuit.
Click to expand...
Click to collapse
Agreeable for nexus 6 which has inherent wireless charging inbuilt, I am using an external wireless case for my iPhone 5s can you please hint on this aspect also.
Thanks in anticipation.
Colonel Singh
amanamarsingh said:
Agreeable for nexus 6 which has inherent wireless charging inbuilt, I am using an external wireless case for my iPhone 5s can you please hint on this aspect also.
Thanks in anticipation.
Colonel Singh
Click to expand...
Click to collapse
Sorry - I know nothing (and nor do I want to know anything!) about iPhones.
However, as a general rule, charging is normally managed by the handset, not by the charger.
Has anyone had success getting wireless charging to work on the 6T? Before you start, I know, it's not built in. I mean with one of those little cards you plug into the bottom and slip between the phone and case. I have a 10w capable charging pad I'd like to use. The receiver I got doesn't seem to go in far enough. When plugged in to my old 3T, it will charge wirelessly and it doesn't go all the way into the phone unlike the 6T. I noticed that with the official OP charging cable there is a little click when inserting when then and only then it will charge. I can't get the receiver in far enough before bottoming out to get that click. Or would current output not be high enough on the receiver for the phone to recognize?
CosMiiK said:
Has anyone had success getting wireless charging to work on the 6T? Before you start, I know, it's not built in. I mean with one of those little cards you plug into the bottom and slip between the phone and case. I have a 10w capable charging pad I'd like to use. The receiver I got doesn't seem to go in far enough. When plugged in to my old 3T, it will charge wirelessly and it doesn't go all the way into the phone unlike the 6T. I noticed that with the official OP charging cable there is a little click when inserting when then and only then it will charge. I can't get the receiver in far enough before bottoming out to get that click. Or would current output not be high enough on the receiver for the phone to recognize?
Click to expand...
Click to collapse
I have been using wireless charging since day one. No issues at all. Lay it on wireless charger at night. Wake up to full charge. No need to charge through out the day cause battery is fantastic. This is the one I use.
https://www.amazon.com/gp/aw/d/B01M11UT3V?psc=1&ref=yo_pop_mb_yo_pop_mb_pd_t2
borijess said:
I have been using wireless charging since day one. No issues at all. Lay it on wireless charger at night. Wake up to full charge. No need to charge through out the day cause battery is fantastic. This is the one I use.
https://www.amazon.com/gp/aw/d/B01M11UT3V?psc=1&ref=yo_pop_mb_yo_pop_mb_pd_t2
Click to expand...
Click to collapse
Thank you! Just ordered one.
What is the point of using that thing are you guys saying you keep it plugged into the phone all day long? Wouldn't that get in the way or be annoying?
Swimguy14 said:
What is the point of using that thing are you guys saying you keep it plugged into the phone all day long? Wouldn't that get in the way or be annoying?
Click to expand...
Click to collapse
This phone can pretty much be charged once a day with the way most of us are using it. Having it slowly charge over night with wireless charging may be less straining in the battery. I'm tempted but so far I just charge to around 80% at night before bed and unplug overnight.
I was looking at that one on Amazon. Seems like the gold one on there may be better?
My question is, if you have to plug the wireless charging card into your USB C port anyway, does that defeat the entire purpose? Not dissing it or anything, that's very subjective, but.....
H4X0R46 said:
My question is, if you have to plug the wireless charging card into your USB C port anyway, does that defeat the entire purpose? Not dissing it or anything, that's very subjective, but.....
Click to expand...
Click to collapse
That's what I was thinking
Swimguy14 said:
That's what I was thinking
Click to expand...
Click to collapse
Just remove cable. No big deal I have done this. Plus I don't use the dongle only Bluetooth headphones.
The reason that I use a wireless charging receiver pad plugged into my usb-c is because I've seen more than one of them go bad on other phones.
Besides the power button, the next most likely part of a phone to fail is its charge port. Likely because of sheer mechanical wear and tear on both these components. Which is why I use gestures to turn on and off my display, and that wireless receiver.
However, it's not without drawbacks:
- I'm not sure that having something perpetually plugged in doesn't stress the port much less than taking something in and out. But I figure it does.
- It's a pain to use the port for anything else, like otg drives or wired headphones or adb
- dash charging is WAY faster than wireless
CosMiiK said:
Has anyone had success getting wireless charging to work on the 6T? Before you start, I know, it's not built in. I mean with one of those little cards you plug into the bottom and slip between the phone and case. I have a 10w capable charging pad I'd like to use. The receiver I got doesn't seem to go in far enough. When plugged in to my old 3T, it will charge wirelessly and it doesn't go all the way into the phone unlike the 6T. I noticed that with the official OP charging cable there is a little click when inserting when then and only then it will charge. I can't get the receiver in far enough before bottoming out to get that click. Or would current output not be high enough on the receiver for the phone to recognize?
Click to expand...
Click to collapse
Why would you like to have a wireless charger? The cable charging is amazing is so fast. I normally charge round at 30 percent and I went to play battlefield 5 two games my phone will be fully charged is so fast. Not worth it to get a wireless charger. But is your phone do what you want I'm just here to give you a opinion lol
CosMiiK said:
Thank you! Just ordered one.
Click to expand...
Click to collapse
borijess said:
I have been using wireless charging since day one. No issues at all. Lay it on wireless charger at night. Wake up to full charge. No need to charge through out the day cause battery is fantastic for Edu Birdy website. This is the one I use.
https://www.amazon.com/gp/aw/d/B01M11UT3V?psc=1&ref=yo_pop_mb_yo_pop_mb_pd_t2
Click to expand...
Click to collapse
Thanks. This battery fixed my problem.
borijess said:
I have been using wireless charging since day one. No issues at all. Lay it on wireless charger at night. Wake up to full charge. No need to charge through out the day cause battery is fantastic. This is the one I use.
https://www.amazon.com/gp/aw/d/B01M11UT3V?psc=1&ref=yo_pop_mb_yo_pop_mb_pd_t2
Click to expand...
Click to collapse
Does it work if I have the terminal with the original red case?
Lack of wireless charging is my only real gripe with the 6T. This sounds like a good solution if you never plan to use the USB port. I like the quick wired charging but having the option for wireless would be a good feature. How hard could it have been for OnePlus to add? Is the back case metal? It looks like glass to me.
Just easier for me to plug in my USB-C slow charger. Not sure what the advantage is to doing this. If you put it between the back of the phone and a case, I get it. Just plugging it into a USB-C wireless receiver seems like a waste of 15 -20 bucks for zero gain. At least for me.
I bought this one so I can still charge it if needed. https://www.amazon.com/gp/product/B07QNW32V4/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1