Hold onto LTE - Xperia Z5 Compact Q&A, Help & Troubleshooting

Anyway to set the device to hold onto LTE longer? Due to the issues with the way the phone reports signal, it commonly hands off to 3G/hspa when it isn't really necessary.
Sent from my E5823 using Tapatalk

man in my case the phone holds onto the weaker LTE signal for dear life.

Related

Any way to boost 3g?

I've noticed that when I plug my S into my laptop at college, I get a slightly better signal than without, which is actually no 3g signal at all. So I was wondering if there is anything I can plug into the phones usb port to boost my signal while in low signal areas?
No, what you're saying is just a coincidence.
Sent from my EPAD using Tapatalk 2
Only a baseband change could boost the signal and I read somewhere the kernel.
Sent from my LT26i using Tapatalk 2
I can guarantee you it isn't a coincidence.
I've been going to college for months and never had a 3g signal. I borrowed a cable to charge my phone up, since I never take mine in and suddenly, I was getting 1.7Mbps if I positioned it the right way.
But if there isn't anything, then I guess I'll stick to the way I'm doing it now.

Spotty, Erratic WiFi Signal Problem - Anyone Else?

Had my One X+ for about 6 days now. Noticed that in parts of my home, had network connection issues where I never had them with any other devices. Dowloaded Wi-Fi Analyzer and SpeedTest. Downloaded SpeedTest on my old iPhone 4. And I confirmed that my phone has many more issues connecting in parts of the home than the iPhone. It's VERY erratic. You can put it on the counter 6 inches below where you were holding it with your hand, and wala, better signal. Pick it up and signal goes to crap. It's mainly with the 5.6ghz signal but 2.4 is effected to. Enabling / Disabling the Wi-Fi Performance Enhancement setting in Setting > Wi-Fi > Settings makes no difference that I can see and I compared it on and off several times using Wi-Fi Analyzer. This may be a dealbreaker for me on this phone. Maybe have to exchange it for an S3.
At times it loses connection briefly, then when it re-connects, signal is much better but it's not consistent. When running Speedtest on iPhone gauge usually goes up fairly smoothly and stays there (not always). On One X+ gauge gets "stuck" a lot more often and/or goes down.
I run an ASUS RT-56U router with latest firmware. Works excellent. It has my same network SSID bound to both 2.4 and 5.6Ghz channels. It's almost as if the One X+ has trouble dealing with a drop in the 5.6 and seamlessly moving everything to only 2.4? I actually tried to lock the phone to 2.4 or 5.6 in settings, frequency. It went crazy, both settings, it can't connecting and disconnecting.
Wondering if it is a hardware fault that was found in original One X that may have not been fixed?
http://www.google.com/search?q=htc+...c+one+x++wifi+signal&sourceid=chrome&ie=UTF-8
jazee said:
Had my One X+ for about 6 days now. Noticed that in parts of my home, had network connection issues where I never had them with any other devices. Dowloaded Wi-Fi Analyzer and SpeedTest. Downloaded SpeedTest on my old iPhone 4. And I confirmed that my phone has many more issues connecting in parts of the home than the iPhone. It's VERY erratic. You can put it on the counter 6 inches below where you were holding it with your hand, and wala, better signal. Pick it up and signal goes to crap. It's mainly with the 5.6ghz signal but 2.4 is effected to. Enabling / Disabling the Wi-Fi Performance Enhancement setting in Setting > Wi-Fi > Settings makes no difference that I can see and I compared it on and off several times using Wi-Fi Analyzer. This may be a dealbreaker for me on this phone. Maybe have to exchange it for an S3.
At times it loses connection briefly, then when it re-connects, signal is much better but it's not consistent. When running Speedtest on iPhone gauge usually goes up fairly smoothly and stays there (not always). On One X+ gauge gets "stuck" a lot more often and/or goes down.
I run an ASUS RT-56U router with latest firmware. Works excellent. It has my same network SSID bound to both 2.4 and 5.6Ghz channels. It's almost as if the One X+ has trouble dealing with a drop in the 5.6 and seamlessly moving everything to only 2.4? I actually tried to lock the phone to 2.4 or 5.6 in settings, frequency. It went crazy, both settings, it can't connecting and disconnecting.
Wondering if it is a hardware fault that was found in original One X that may have not been fixed?
http://www.google.com/search?q=htc+...c+one+x++wifi+signal&sourceid=chrome&ie=UTF-8
Click to expand...
Click to collapse
If u got a problem with WiFi in certain areas of Your HOME i dont think its hardware problem. If u have a hardware problem Your WiFi couldnt recive more than "dot" signal even near router. Its because hardware issue was about antennas of WiFi (they were f****) To test hardware issue on HTC ONE X after squeze certain area of phone (antennas connected) signal growed up after release signal went down...
Looks like my hunch may be correct in that it has something to do with the phone switching between the 2.4Ghz and 5.6Ghz bands. 2.4Ghz has much better range. But in the wi-fi settings it is set to Auto frequency. What appears to be happening is that the phone prefers 5.6 but when it loses it, it switched to 2.4. I have a "dual band" N router so the same SSID is bound to both frequencies. I think this improves bandwidth for devices that communicate on both at same time (or is that not possible?) But I can't seem to get it to work if I change the frequency setting to anything but Auto. It won't authenticate when not on Auto! Bug?
Related One X Thread here:
http://forum.xda-developers.com/showthread.php?t=1730383
I've been struggling with WiFi issues on my phone as well. Whether the phone is set to 2.4GHz, 5GHz or Auto, the connectivity is spotty at best.
With other devices in the house including my old Inspire 4g, a Kindle Fire and an iPhone I can get full reception but only 1 bar on the One X+ in spots. I have noticed that holding the phone upright in poor reception areas brings the connectivity up a bar or two usually but that's not optimal for usage... Same thing happened at the girlfriend's family's house yesterday and my connectivity was also progressively more spotty at work in the past week since getting the phone.
The screwy thing is it seems completely intermittent. It'll be fine for a few hours then suddenly the connectivity goes to crap. I'm pondering exchanging the phone for another just to see if the issues persist.
I spent much of Thanksgiving (sadly) testing the WiFi on this phone using WiFi Analyzer and speedtest at locations all over my house. I compared results with an iPhone 3GS Iphone 4 and Samsung Series 6 notebook. The One X (+) was terrible. At times it performed well but in the exact same location, the next time it would perform dismally. Very unpredictable and erratic and I found out why!
** THERE IS A 20+ dbm DROP IN SIGNAL WHEN HOLDING THE PHONE IN THE PALM OF YOUR HAND! **
Now this may be common with a lot of phones, I don't know. But, the signal strength on this phone is already not what I would describe as "Best in Class" so this drop in many areas where the signal is moderately low to very low, holding the phone in the palm usually makes a difference as to if you have a usable connection or not!
I have a highly respected ASUS RT-56U router and made sure I had the latest firmware installed, but as I said, even the iPhone 3GS had more consistent, better, even results compared to this phone in many low signal areas when I held the One X in my hand. So it's not the router, it's the device.
Next step is to try to determine if it is this one phone, the One X+ AT&T model, and the One X AT&T model, or all One X models, including International? I will head to the store to see if they will let me run the test on another phone. I'm praying it is this particular phone but my gut tells me it is probably an issue in the design of the phone. I really like this phone but may have to go for the Samsung Galaxy SIII instead as this wifi issue is BAD, and unacceptable. Would get a Nexus 4 but I need more than 16GB of memory!!!!!
I shot a video about this showing the Wifi Analyzer running:
http://www.youtube.com/watch?v=8IUkbnj5pY0
Well, this morning I did similar testing and am seeing a 20-25 dBm drop whenever I pick the phone up...
Have you had a chance to check with your local AT&T store about testing other One X+ phones?
Sent from my HTC One X+ using xda app-developers app
tier~ said:
Well, this morning I did similar testing and am seeing a 20-25 dBm drop whenever I pick the phone up...
Have you had a chance to check with your local AT&T store about testing other One X+ phones?
Sent from my HTC One X+ using xda app-developers app
Click to expand...
Click to collapse
It would seem pointless now, since you are having the same issue, it seems to be an issue with the any One X+ (and I would bet also any One X). Maybe there's always a drop on any phone (iPhone there's no analyzer to show you signal). But this large 20-25 dBm drop make a difference between fast/normal browsing and slow/no browsing on the Net when sitting in many areas of my house. I would expect using it at other locations (on trips, etc.) it will drive me nuts. I do A LOT of browsing, use the phone like a mini tablet. So fast WiFi connectivity is paramount! I get better 4G LTE range/speeds than wifi in those areas of my house, but don't have unlimited data!
Sounds pretty simple, either u need a better router or u have a bunk phone. I have WiFi all over my house, my parents house, my work, all with zero issues and all obviously different routers. I'd maybe try another device. You have 14 days in the state's no questions asked for a new phone exchange.
It's not router. I went to AT&T store. Rep had S3. He loaded Wifi analyzer. We monitored same wifi network next shop down. HTC, signal dropped almost 20 dBM when you put it in your palm. S3, not change or 5 dBm at most. Loaded WiFi analyzer on X+ on display, but palm around it best I could around the display mount, big signal drop.
I have a large home. The thing is, no other devices have issues. What I suspect is with my home, certain areas push the HTC One X+ to its limit as far as wifi range. Most users don't notice "issues" as they don't lose a connection. And I didn't lose connection either, or rarely, just got really slow. You have to walk all around and look at WiFi Analyzer and compare holding fold to setting phone on table. Then also compare Speedtest.net app results. With S3 and notebook computer I'm getting 20mbit speeds in most areas, difficult areas, still has a consistent 6-8mbit speed. HTC One X+ those problem areas, 1mbit speeds if lucky or loss of connection.
Since nothing is changing in the test environment besides the device, the HTC clearly has poor wifi reception *RELATIVE* to other devices when held in palm of your hand. I found though you can get around this if you hold lower half of phone no issues and if you turn phone on its side, not as bad of a drop either.
I made it up to the AT&T store yesterday afternoon just to compare to another HOX+. Same thing was happening with the floor model of the phone. The manager went ahead and replaced my phone with a new one regardless just to cover our bases but like you said jazee, it does appear to be the radio location in the phone causing the issue. Just have to be conscientious of how I hold the phone.
To compensate I cranked up the TX power on my router a little bit which has helped. I run dd-wrt on it though so I have that option. Not sure what your firmware gives you access to in your Asus router. I have heard Padavan's custom firmware is a good option if you want to do more than what the stock firmware gives you access to.
jazee said:
I spent much of Thanksgiving (sadly) testing the WiFi on this phone using WiFi Analyzer and speedtest at locations all over my house. I compared results with an iPhone 3GS Iphone 4 and Samsung Series 6 notebook. The One X (+) was terrible. At times it performed well but in the exact same location, the next time it would perform dismally. Very unpredictable and erratic and I found out why!
** THERE IS A 20+ dbm DROP IN SIGNAL WHEN HOLDING THE PHONE IN THE PALM OF YOUR HAND! **
Click to expand...
Click to collapse
I get a similar drop, but more along the lines of 10 dbm.
Try keepalive from playstore
Sent from my HTC One X+ using Tapatalk 2
Same WiFi issue
I'm having the same issue as jazee (OP). I browse on my WiFi and then when I click on a link, I just hold the phone in my fingertips (not palm) and the signal jumps up and page loads.
Assuming olorolo's on to something here and there is an app to fix it... I'm heading to the play store to see what I can find like "Keepalive" as recommended. This is my first foray into Android though, so I can't help but wonder if you guys are already ahead of me. Any luck yet fellas?
Yes if you hold phone below volume rocker, or sideways, or even in palm with right instead of left hand, you can mostly mitigate the signal drop.
I'm happier on S3 except having to go back to ICS 4.0.4 and wait for JB 4.1. No wifi issues, much better battery usage, and no could pegged at times by Beats trying to scan my 2800 mp3 files in the background for some reason. Could tell as HTC gets HOT and then battery plummets. Brand new phone. Maybe some issues to work out?
Oh and I love having 2GB Ram for multitasking better. Would have hot S3 initially if I realized US ver had 2GB ram like new Nexus 4.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Looks like a case helps
jazee said:
Yes if you hold phone below volume rocker, or sideways, or even in palm with right instead of left hand, you can mostly mitigate the signal drop.
I'm happier on S3 except having to go back to ICS 4.0.4 and wait for JB 4.1. No wifi issues, much better battery usage, and no could pegged at times by Beats trying to scan my 2800 mp3 files in the background for some reason. Could tell as HTC gets HOT and then battery plummets. Brand new phone. Maybe some issues to work out?
Oh and I love having 2GB Ram for multitasking better. Would have hot S3 initially if I realized US ver had 2GB ram like new Nexus 4.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
I just so happened to have got my case in the mail today -- Ballistic SG -- and with it the WiFi drop is much less (more like 10dBm). I kept scanning with WiFi Analytics and no matter how I held it in my hands, I could never reproduce the -80dBm I was getting, no case, in the palm of my hand in the exact same spot.
For what it's worth anyway, it seems like the half centimeter of case is helping. I never would have noticed if I bought the case on day 1.

[Q] Signal loss - Death Grip

Alright, I read the review on this phone and, after having the GalaxyS 1, I thought trying an HTC would be a great idea as my GS1 had extreme screen burn in; which led me to opt for an HTC instead of GS2 - the cheaper alternative of course.
I was pretty happy with this phone. Somewhat smaller than what I expected, though it runs fairly well with ICS and HTC Sense loaded.
Now the ridiculous issue. This phone has a severe case of 'death grip'. I've had quite a couple of frustrating weeks trying to figure out what on earth was causing the signal to drop completely from 2 or 3 bars to dead, when picking the phone up to text.
Before I considered googling 'hand signal absorb htc', or similar keywords to that effect, I tested my theory by holding the phone at the top two edges and then in my palm again; in the same position both times. The result? 5 bars to two bars, or even in some cases one bar. The signal where I live isn't excellent, however it's not terrible either. With my GS1 having no issue with signal drops. Just holding the Desire X in the palm of my hand, under the table results in complete signal loss.
This is an absolute joke. I've missed really important phone calls and the majority of sms's arrive late due the lovely signal loss regain repetition, essentially causing the phone do not receive calls, even though, provided it does have 3 or so bars.
So, am I the only one here who has this issue, or for that matter; a faulty phone? Really Really disappointed.
I do have a signal drop problem as I already wrote on another post and nobody answer:
"I have a lot of signal drops on GSM/EDGE and also 3G/HDSPA? The signal is full but, the phone is in stand by, the signal drops and I loose calls. Does anyone have this problem?
Also I noticed when the phone switches from 3G to GSM/EDGE first I have a no signal period (couple of seconds)."
I also had this problem with an LG Optimus 2x when updated to Android 4.0.4.
Dal2000 said:
Alright, I read the review on this phone and, after having the GalaxyS 1, I thought trying an HTC would be a great idea as my GS1 had extreme screen burn in; which led me to opt for an HTC instead of GS2 - the cheaper alternative of course.
I was pretty happy with this phone. Somewhat smaller than what I expected, though it runs fairly well with ICS and HTC Sense loaded.
Now the ridiculous issue. This phone has a severe case of 'death grip'. I've had quite a couple of frustrating weeks trying to figure out what on earth was causing the signal to drop completely from 2 or 3 bars to dead, when picking the phone up to text.
Before I considered googling 'hand signal absorb htc', or similar keywords to that effect, I tested my theory by holding the phone at the top two edges and then in my palm again; in the same position both times. The result? 5 bars to two bars, or even in some cases one bar. The signal where I live isn't excellent, however it's not terrible either. With my GS1 having no issue with signal drops. Just holding the Desire X in the palm of my hand, under the table results in complete signal loss.
This is an absolute joke. I've missed really important phone calls and the majority of sms's arrive late due the lovely signal loss regain repetition, essentially causing the phone do not receive calls, even though, provided it does have 3 or so bars.
So, am I the only one here who has this issue, or for that matter; a faulty phone? Really Really disappointed.
Click to expand...
Click to collapse
Sounds like a faulty antenna. Either that or you have lead hands.
It should be a cheap fix at any local repair shop or free if you take it back to the shop for a replacement.
Sent from my Nexus 10 using XDA Premium HD app
vogonpoetlaureate said:
Sounds like a faulty antenna. Either that or you have lead hands.
It should be a cheap fix at any local repair shop or free if you take it back to the shop for a replacement.
Sent from my Nexus 10 using XDA Premium HD app
Click to expand...
Click to collapse
What I don't understand is, when i'm on an actual phone call, there's no issue with quality or signal loss. Sounds like the phone rom is preserving the antennas power in idle mode?

Poor signal

My i9205 have generally poor signal compared to my note1. It doesn't seem to make any difference to turn of LTD. I have not experienced any call dropping, only referring to the displayed signal. My note shows full signal while i9205 shows minimum signal. And in battery usage the "Cell Standby" is quite high and normally with 10-20% "Time without signal" even if I have not noticed any time without signal.
Anyone have similar issue ?
I have the Mega GT-I9200 and experience spotty signal as I drive around. I am on T-mobile in New York. Within a 15 mile radius in New York City my signal will fluctuate between HSPA+, Edge, G (1st generstion GPRS), and sometimes complete loss of both data and cellphone signal. I think the issue is I might need a modem to be ported from a t-mobile device to give me a consistent signal. Not sure if anyone could do that or if there's even a t-mobile device whose modem would be compatible at this point.
Sent from my GT-I9200 using xda app-developers app
Yep! I'm definitely getting this too. The phone very rarely shows the full 4 bars of reception, and in low signal areas (1 bar or less) the phone starts flipping between GSM/WCDMA (UMTS) constantly, giving very poor reception. Also, signal strength in general isn't as good as my nexus 4 was. I sometimes am unable to reliably maintain a signal at all in areas that I know my N4 could reliably hold 1 bar of strength, with the phone disconnecting from the network completely and then reconnecting all the time.
As I'm in the UK and without LTE anyway, I've switched the phone to WCDMA mode only, which has helped though the phone now just flips between HSPA and HSPA+ when in poor signal. Its certainly much more usable this way at least.
On the upside, yesterday night with 3 bars reception I was consistently able to get over 15Mbps download, with my best result of nearly 19Mbps! So it doesn't look to be a hardware issue.
I'm speculating wildly here but to me this looks like a SW issue in one of two areas: signal strength isn't being reported correctly (too low), causing the phone to take action to try and obtain a better signal (by flipping to a lower bandwidth protocol or disconnecting and trying to detect a better macro, for instance) when it isn't really necessary OR maybe the phone is just too aggressive in switching from HSPA+ down to GSM to save battery.
Is there some way to take control of the mechanism, and try to force the phone to stay in hspa+, or to spoof a higher signal strength?
EDIT: This phone is packaged with very thin plastic wrapping over the metal band that runs around the circumference of the device. I accidentally left a lot of this wrapping on for the first few days. It may be complete crap, but I think my signal might have improved since I removed it all! I certainly seem to be able to maintain a connection in places that I wasn't able to last week, and maintain a constant (4-5Mbps) HSPA+ link in areas that I couldn't before...
Time will tell...
I have the same encounter, I have two sim cards belong to the same number one for phone and one for tablet. The one in Mega 6.3 give me three bar signal but the one in Galaxy tab plus 7" give me four bar signal :crying:
I am also having reception issues with my mega 6.3 I get worst reception than any of my other phones sitting in the exact same spot. I am on ATT in the US. I removed all the plastic around the phone. I am wondering if it is my APN settings. Hopefully someone can shed some light on this or there is something eles going on.
The Mega has an issue with the radio. I bought two of these an i9200 and i9250. Both Mega's would lose signal completely. I don't have the greatest signal here at my home, but it has never been an issue with any other phone such as Note 1 and Note 2 and many others. If you are in a weak signal area more than not, you may wamt to hold off until the radio issue is resolved with software or whatever. They were unusable for me and I re-sold them.
Sent from my GT-N5100 using xda premium
I have an i9205 and it's fine with the signal. I'm in the UK though
The big problem about this is that the phone uses much more battery when signal is low and using 3G. I can get 6-7 hours screen on time on one charge while wifi is on. But when using 3G with low signal I get 3-4 hours.
I hope this is a radio firmware thing, and not a hardware thing, so that it could be improved with updates.
so any updates?
Same problem here with my new Mega 6.3! My phone have only 1 or 2 bars signals while my brother's Samsung Grand has full antenna easily. It's very annoying. What should we do?!
Same ****ty reception going on with mine. I returned it.
I changed it too. New one is working fine.
hi. ah really? changnig phone u noticed a consistent improvement in reception?
but... i can say that i and my girlfriend, using a DIFFERENT SELLER...... we have the same problem of cell standby
I found that all phone models are inconsistent in radio reception, not sure why...
Sometimes the updates can do a little better, but I believe the hardware is the most limiting factor.
Maybe Mega isn't for you where you live, just return it then get another phone
i have poor signal Too
Any news or solution ?

[Q] Weak WiFi Reception

Just picked up the HTC One Max from Verizon yesterday. I have not rooted it or done anything other than set up email. As soon as I brought it home I noticed that it was having trouble with my home's WiFi that my Gnex didn't have. I placed my Kindle, my Gnex, and the HTC One on the table next to each other. The router shows the signal from the Kindle as -35 dbm, the Gnex as -37 dbm and the HTC One Max as -60 dbm. Considering that it's 12 feet from the router with no walls in between, that's an awful signal. It causes the Max to be limited to about 11 Mbps. When I take the Max into another room it just drops the WiFi altogether.
Is there some setting I might be overlooking? I tried turning off WiFi optimization, but that didn't change anything.
Here's a picture of WiFi Analyzer running on the Gnex and the Max side by side to illustrate.
Nexus = cheap plastic frame while One Max = metal frame and dual stereo speakers (aka stereo interference that affects reception).
I still choose the Max.
GNRDuncan said:
Here's a picture of WiFi Analyzer running on the Gnex and the Max side by side to illustrate.
Click to expand...
Click to collapse
What router ?
Sent from my Nexus 7 using Tapatalk
Jiggity Janx said:
Nexus = cheap plastic frame while One Max = metal frame and dual stereo speakers (aka stereo interference that affects reception).
I still choose the Max.
Click to expand...
Click to collapse
I agree with your assessment of the build quality of Samsungs (I went from a Gnex to a Max for a reason), but working WiFi is a must. I can't get 4G or even 3G most of the time at home and I don't have unlimited data anyway. The Max won't even connect to the WiFi in the next room. I can't believe this is how all Maxs are, so I'll exchange it tomorrow and check it out.
dottat said:
What router ?
Click to expand...
Click to collapse
Mine is a Buffalo WHR-HP-G54 running Tomato, but I don't know what's running on the other routers the Gnex is picking up. The router model won't matter in a side-by-side comparison of signal strength anyway - the router only broadcasts one signal and each phone receives that signal. As long as they're in the same place, the power of the signal reaching them will be the same. You can see that in this example where the Gnex is picking up three other routers that are presumably different models than my own, and that don't even register on the Max. If WiFi analyzer is anything close to correct, the Gnex is 1,000 times more sensitive than the Max. The Gnex registers about the same as my Kindle and the wife's Droid X2, so I don't think Samsung has anything special going on. I can see having some difference between designs and WiFi chips, etc., but I really don't believe Samsung's WiFi circuit is 1,000X more powerful than HTC's. That's about what I'd expect to see if the antenna weren't connected or some such.
On the other hand, my cellular reception is phemomenal compared to the Gnex. I just hope it's this particular Max with a problem so I can just exchange it and use WiFi.
I don't have any issues with wifi connectivity on my Max. I haven't run any analyzers because I haven't had the need to. I would take it in.
GNRDuncan said:
Mine is a Buffalo WHR-HP-G54 running Tomato, but I don't know what's running on the other routers the Gnex is picking up. The router model won't matter in a side-by-side comparison of signal strength anyway - the router only broadcasts one signal and each phone receives that signal. As long as they're in the same place, the power of the signal reaching them will be the same. You can see that in this example where the Gnex is picking up three other routers that are presumably different models than my own, and that don't even register on the Max. If WiFi analyzer is anything close to correct, the Gnex is 1,000 times more sensitive than the Max. The Gnex registers about the same as my Kindle and the wife's Droid X2, so I don't think Samsung has anything special going on. I can see having some difference between designs and WiFi chips, etc., but I really don't believe Samsung's WiFi circuit is 1,000X more powerful than HTC's. That's about what I'd expect to see if the antenna weren't connected or some such.
On the other hand, my cellular reception is phemomenal compared to the Gnex. I just hope it's this particular Max with a problem so I can just exchange it and use WiFi.
Click to expand...
Click to collapse
Only reason I ask is there had been a couple model routers that have had issues with HTC ones. What you describe has not been my experience. Exchange it.
Sent from my Nexus 7 using Tapatalk
GNRDuncan said:
I agree with your assessment of the build quality of Samsungs (I went from a Gnex to a Max for a reason), but working WiFi is a must. I can't get 4G or even 3G most of the time at home and I don't have unlimited data anyway. The Max won't even connect to the WiFi in the next room. I can't believe this is how all Maxs are, so I'll exchange it tomorrow and check it out.
Click to expand...
Click to collapse
I am pretty sure you have an hardware issue on your phone. Please go and exchange it. i speak from my experience of my One MAX dis-assembly. i used to get stable/ Full WiFi signals when it was stock, but when i re-assembled it i noticed a drop in WiFi signal and it was also not stable. i opened it up again to tweak the WiFi antennas a bit and tightened the screws properly and then it was good again.
I would suggest you to slightly tap / press on the top left of the phone(the speaker area the light sensor & top LCD bezel) a little and see if you WiFi improves and that would help to confirm the issue. You could place the phone on a firm table and press the area with your thumb and look at the WiFi bar's to check if you notice a difference.
Either way, you need to get the phone exchanged.
pradeepvizz said:
Either way, you need to get the phone exchanged.
Click to expand...
Click to collapse
Thanks to everyone. I exchanged today and the WiFi reception is better than the Kindle and the Gnex. I hope that was an isolated issue and won't be something we see a lot of with the Max.
GNRDuncan said:
Thanks to everyone. I exchanged today and the WiFi reception is better than the Kindle and the Gnex. I hope that was an isolated issue and won't be something we see a lot of with the Max.
Click to expand...
Click to collapse
Good to know! :good::good:

Categories

Resources