Hi guys.
I usually can fix my mistakes but this time I'm stumped. I think I bricked my evo but I don't know if its soft brick or a hard brick. Based on the other posts online mine doesn't really match up.
Here's what I did,
It was late and i was doing a restore on a miui rom through my clockworkmod recovery and it looked to be stuck at the begining for over an hour which is a really long time so i pulled the battery in the middle.
Not smart but my phone came back on and i tried a few backups and it kept happening but i decided to pull the battery one last time and just flash something new but
This time it wouldnt come back on. Eek!
This is what it does,
It will onlyy power on if you plug it in and then press all the buttons. It will boot past the htc logo and then go to the begining of the miui boot animation and stops.
It will not get into fastboot or recovery by holding power and vol down, nothing happens. When you plug it in. The red light comes on for a few seconds then turns off so it wont charge either.
Im really stumped guys. I tried the hard brick guide
Here.
http://androidforums.com/evo-4g-all...k-guide-hard-brick-only-wont-turn-charge.html. and that didnt do anything.
HELP!!!
So, you cannot get into the bootloader screen at all, yet it does boot if you press all 3 buttons? I would pull the battery and let it sit for a while, The other thing I would do is leave the battery out, and plug it into a Windows PC, and see what devices show up. (Particularly within the first 5 seconds, just watch the device manager or the "new devices" screen to see what's showing up)
I would try
Code:
adb reboot recovery
That might get you into recovery in which you can do a superwipe and then flash a working rom.
If it doesnt try
Code:
adb reboot bootloader
then flash an ruu.
It does show up as something when i plugged it in when windows tried to install drivers and ive taken the battery out like a hundred times but no success.
As far as adb method i wasnt finding a clear way to perform that. Is there a walkthrough that you recomend i try?
And thanks for responding guys
fixed!!!!
guys i fixed my phone!!! iTzLOLtrain thank you so much!
by using this guide
http://forum.xda-developers.com/showthread.php?t=1590800
my phone is back on and i cannot beleive it didnt find it sooner!!!!
i hope this thread helps other users!:victory:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
He said he has tested this and can also hear the micro-switch clicking.
scorpionhd2 said:
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
Click to expand...
Click to collapse
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
Darke5tShad0w said:
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
He said he has tested this and can also hear the micro-switch clicking.
Click to expand...
Click to collapse
Thank you very much for helping! :good:
So the question is, whether it's the power button's or emmc's fault...
I did a little searching and found this video. I've got exactly the same problem like the guy. At 1:06 following the boot loop, at 1:34 following the problem with downlod mode.
Although he thinks it's caused to the sudden death problem, but at least in my case I think it's wrong because months ago I did the eMMC Brickbug Check.
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button like in 1:04-1:09 in the video. Which normal working phone turns itself on by simply putting in the battery...?
So it must get a command for turning on - (possibly through a defect power button?)
@Virnik0, do you remember, if you could hear the micro-switch clicking on your phone before replacing the button on the mainboard?
beginnerteur said:
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button
Click to expand...
Click to collapse
Your power button is faulty, replace it before you try fixing anything else.
Thank you very, very much for helping! :good: :good: :good:
Truly the power button was fault although you could hear clearly the "click".
I unsoldered and removed the power module and (by startig with JIG and rebooting via ADB) the phone works as it should. :victory:
Now I'm trying to solder a new power button......it's a bit tricky
Again, thank you very much guys!
I had the same problem, pressed the button many times, and it helped. Thank you for your suggestions
Hello.
I hope someone here can help me.
I successfully flashed Leedroid on my HTC One M9 today. I still wanted to try another ROM, so I installed that one and then decided to go back to Leedroid. As I was flashing Leedroid again my phones screen suddenly turned black (I think at about 80%, didn't see it exactly though...) and after trying different things (combinations of buttons, charging and waiting some time) it won't turn on again. I can tell that the phone somehow boots up, because I can access all the files from my PC when I connect it via USB, also adb shows the device with "adb devices", but as offline. I selected a clean install of HTC_M9-port_LeeDrOiD_10_V4.0.0-R119_rev.78.zip from https://forum.xda-developers.com/one-m9/development/rom-leedroid-one-m9-v7-0-0-rc1-march-t3068468.
It seems like the phone only starts in some way if I press the power button and volume up and volume down, at least then I see the files on my computer.
UPDATE: I seem to be somewhere in the Setup (I guess), if I press Volume Up to turn up the sound and then press power and volume down I can hear the screenshot sound.
UPDATE 2: I figured out a way to get to the twrp recovery adb shell and tried restoring my backup (System, Data, Boot), but the screen stays black. I'm now hearing the default HTC boot sound, so my backup seems to be restored...
I can't post the install.log because I'm not allowed to post links and the text would be too long if I just posted it here...
Also I'm new to custom roms...
Does anyone know anything I can do right now? I have a full backup with twrp from before I installed any ROM, but I can't even see if the phones boots to some menu like the bootloader oder download mode, because the screen stays black...
Any help is greatly appreciated!
Update
If anyone finds this thread and is interested how it turned out:
Since I could not get the screen working again I sent my phone to a repair shop. They tested the phone and told me that a circuit board is broken and they can't repair it.
I'm still not sure how this whole thing happened, but it seems like I'm going to buy a new phone...