Related
I now know the Allwinner A13 is a stripped down version of the Allwinner A10, to be clearer the specifications of my Tablet (from UniFlash and AnTuTu Benchmark) are as follows:
Manufacturer: None
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3, NEON)
CPU frequency: 60.0 ~ 1008.0 MHz
Screen resolution: 800 x 444
GPU vendor: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
RAM size: 512 MB DDR2 RAM
Knowing this, I used UniFlash to make a backup of the firmware bt after using UniFlash to try and load a CM9 Rom on to the Tablet, the Tablet died. After alot of googling I discovered AllWinner based chipsets use Live Suite (sometimes called LiveSuit) to flash firmwares on to the device.
To Flash firmware on to the device you need to follow the attached instructions ((http://dragondevs.com/viewtopic.php?f=159&t=390):
Download LiveSuite (http://www.softpedia.com/get/System/System-Miscellaneous/Live-Suit-Pack.shtml)
Install Live Suite
Start Live Suite
Select the Live Suite image file (folder icon
Turn device off (to be sure hold power button for 12 - 20 seconds)
Hold "Volume Up" button down
Connect the device to your PC (while still holding "Volume Up" down)
Start pressing the power button (you may need to do this once a second for 5/6 seconds)
If you haven't installed windows will ask to install a driver for a device (Dive Id will be something like Vf73465789123465435_Id, if the device is in the right mode, A13-MID, ADB-Interface indicates the tablet has connected in anouther mode).
Once this has finished LiveSuite will detect the device and a wizard will flash the firmware for you.
I have found a working firmware which according to AnTuTU Benchmark gives my tablet a rating of 3047 (see firmware section), this is on the higher end of reported A13-MID tablets
I have found out how to install CWM on to the device via SaussageMod (http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms/). This solution is untested, further more it may be unnessary futher investigation has shown this website (https://www.miniand.com/forums/forums/2/topics/73) has developed a way of create Live Suite images. This is simplier than installing clockworkmod recovery,
I tried to load the following images on to my tablet and failed completely: http://forum.xda-developers.com/showthread.php?p=31043317 It didn't work and forced me to do a firmware refresh.
My other step for the day was to create Ubuntu 10.10 installation then I began following this guide to construct an Xperia Play CM9 Rom/Kernel. once I have created a working ROM (I own an Xperia Play). I'm hoping to be able to modify the kernel to include the relevent A13 drivers, but one step at a time.
TODO
Create Ubuntu Partition
Follow Xperia Play CM9 Rom/Kernel Guide and create working rom (test on my Xperia Play)
Download CT repository (https://github.com/christiantroy) and compare with Xperia Play CM9 rom
Find the relevent drivers from https://github.com/amery/linux-allwinner leaked source
Retrieve offical MALI 400 MP drivers (parts of it have been released) compare with leaked source
Use UniFlash backup of original Rom along with LiveSuite image creation to try and restore original firmware (see If I understand it properly)
Examine Build.prop find out why original firmware displayed ina phone layout and new one is in tablet mode (potentially reference CM supported Tablets).
Attempt to compile a A13 (Sun5i) based rom
Create a google code page to hold all of these thoughts properly.
Left blank will include rom/firmwares here for future reference
Firmware
https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1 - My public Dropbox
http://www.azhuo.net/en/products_A13B_Allwinner-A13_7_inch_Android_4.0_Upgrade.html - password is: tabletpc
http://dragondevs.com/viewtopic.php?f=159&t=390 - McPad F1 firmware
Novo 7 Tools
https://dl.dropbox.com/u/74970692/Novotools_v1.0.apk
SausageMod
http://www.slatedroid.com/topic/29916-scriptmod-for-allwinner-a1x-platforms
Gapps - http://goo.im/gapps/
I have the same tablet and it would be very cool if you succeeded in your attempt to create a CM9 rom for it. I tried ROM made by Tragidy from this thread but there is a problem with touchscreen driver, ROM booted successfully but I could not even unlock the screen cause touchscreen did not work. I finaly flashed rom DCPAD2121.zip using livesuite which I belive is the original ROM that came with tablet and it worked.
I installed clockwordmod using sausagemod successfully, but there is a big problem - no hardware "back" key and only volume up works.
novo7tools.apk works OK for reboot, reboot to recovery or shutdown.
syncing
Thanks, it's slow going at the moment, I only spending ~1 hour each day on it and at the moment trying to sync the CM9 source is painful (it keeps timing out, due to "remote side corruption").
I figure I would start there as all the firmware images I can find are ICS roms (meaning the drivers must be ICS).
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
WillingMagic said:
You should check this topic:
http://forum.xda-developers.com/showthread.php?t=1861445
Click to expand...
Click to collapse
I tried that ROM, on my tablet after flashing the ROM it got stuck in a boot loop. It might be an idea to steal the config he created. The ROM is pre CM9 release. The A10 Flash kitchen software seems to work. I was hoping on producing a complete Live Suit image that people could flash (figuring our what CT has done on the A10 took a while).
Still having fun trying to sync the repositories, given up on trying to use a Debian VM, I'll will install full Ubuntu on a drive tomorrow, hopefully that will help fix things. It doesn't help most of the guides I can find are out of date and I keep having to make corrections.
I've also uploading all firmware I can find to my dropbox (at 200mb each they will take a while), I won't with tools simply because others ask you not too.
The Dropbox firmware was out of date when I tried to download it sun5i_android_a13-pfdq88_en_D06 firmware worked well for me, the firmwares are located at: https://www.dropbox.com/sh/bzjt7mzuftwz79f/nt7mRMPDj1
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
WillingMagic said:
Cyanogenmod 9 in not working for you. Did you made data and cache wipe? Can you send me logcat and dmesg output?
You can`t steal my config, you have to remember about credits, and other stuff.
Creating a wiki is useless, there is already wiki for allwinner products, so better update info on it.
Github is better than google code to keep sources.
Using Livesuit=Windows, I hate dual booting just for flashing, Clockwork Recovery or modified SDcard with uboot is better solution.
Current kernel is not working well, with sun5i.
Using VM is stupid, because building rom takes a lot of time on quad core pc without it.
Click to expand...
Click to collapse
I wiped the caches I couldn't send a logcat or dmesg as the device simply boot looped.
I've been providing links to threads whenever I come across others work, I'm new to android rom development for me this is a research effort which will hopefully produce something cool for my £50 tablet. Basically my day job has switched to developing UI's and I am looking for something new to learn (instead of why is Vaadin, Guice, SWT, Javascript, etc... is putting that button there).
Said dev career has also made me hate Git with a passion (not as bad as perforce but still) since Git integrates poorly with Visual Studio and Eclipse and you end up getting everyone overwriting each others changes. The idea of google code is simply because it makes a good platform for projects and you can use things like git with it. I didn't know about an Allwinner wiki, with all of my Googling I haven't come across it, where is it?
I don't care about build times I'm just researching, alas Debian has caused me enough problems so I've installed ubuntu on to a old disk I had lying around. Considering I've just tried to install Ubuntu via a Net install CD and it has screwed up the GRUB installation (nicely taking out my windows partition as well) can you blame me?
The reason for nabbing the config (and the Xperia Play and Christian Troys) is to understand how they work. Over the years I've found most Open Source software documentation is poor unless you have a set level of knowledge about it already.
Lastly I like automation, I want things to just work. Livesuit does that since I am normally a windows user, I as hoping in the distant future once I understand the build process to set up a Jenkins server to do it and create the whole lot automatically (via the Allwinner flash kitchen). In the even longer term I would like to update FlashTool to do what LiveSuit does. In the near term (next couple of months) I just want to be able to build a CM9 image.
All android and kernel source are keep on git, so changing it is stupid.
This is allwinner wiki: http://rhombus-tech.net/allwinner_a10 you can also update http://elinux.org/Hack_A10_devices
Everyone use CWM and it's standard for unofficial firmware/ROMS
brandonlee2 said:
Hi, I have the same tablet but I cannot find the firwmare DCPAD2121.zip
Could you upload it please? From dropbox has been deleted
Thanks
Click to expand...
Click to collapse
Here's my upload, I packed it in rar format: http://www.mediafire.com/?we4zhgop29bg3dj
I also found it here: https://docs.google.com/open?id=0BzQuMwoMQqvba1VtQ1p1ZWJkR2M
from this forum post: http://www.slatedroid.com/topic/35314-a13-generic-tablet/page__view__findpost__p__421128
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
myfluxi said:
I built a CM10 rom for A13 from sources. It boots fine but hangs either at the Android setup wizard or sometimes even at the CM animation.
Click to expand...
Click to collapse
Mind sharing your repo ?
Trying 4.1.2
Hi all,
So I've tried compiling from 4.1.2 source for my A13 Emgeton Consul 3
It boots up and gets to the CM10 boot animation but it doesn't get past it.
I can adb at first boot until adb stops.
logcat from boot attempt:
http://pastebin.com/gLTrieHm
My build.prop:
http://pastebin.com/Ap9M1tjW
Any pointers as to why it doesn't get past the boot animation?
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
phoivos86 said:
Hello guys! I know it's not he proper place here to pose my question, but I am definitely at loss!
Do you happen to know if there is a way of rooting this tablet? And if so, does everything work properly after that?
Click to expand...
Click to collapse
Mine came pre-rooted.
Just received my MID A13 Tablet. Is this thread dead?
koodiifin said:
Just received my MID A13 Tablet. Is this thread dead?
Click to expand...
Click to collapse
I've gone a bit quiet on the development front, setting up a file/media server & samba domain server to power my home network is eating up my time.
My dropbox contains every image I could find for the tablet, as mentioned previously you can root the device using saussage mod, although my device and every one of those images is already rooted. You can prove this by installing super user.
Sassage mod's clockworkmod recovery doesn't work for me and I was looking at the backup tool in order to generate my own one. If you are aimed at any development, let me know and I will update the main thread
Many have said that they have "lost" "forget" to take backup from original rom. So, i'd like to have backup from my original to go back if/when something goes wrong. How do i do that? What software i need. Do i need to root?
This is from my info sheet:
Model TWD_MID
android version 6.0.1 ?????
Baseband 1.5
Kernel 3.0.8+
Buildnumber: nuclear_evb-eng6.0.1 IMM76D 20120917 test keys
I am in a desperate need for some help:
My tablets specs are these:
Phone model: A13-MID
Brand: softwinners
CPU hardware: sun5i
CPU model: ARMv7 Processor (VFPv3.NEON)
CPU frequency: 60.0 - 1008.0 MHz
Screen Resolution: 800 x 444
GPU vendor: ARM
GPU render: Mali-400 MP
GPU version (OpenGL): OpenGL ES 2.0
Memory size: 353.5 MB
Android version: 4.0.4
Build number: nuclear_pfdq88c-eng 4.0.4 IMM76D 20120821 test-keys
Kernel: Linux version 3.0.8+
I just installed OpenVPN installer and installed the OpenVPN binary in the system/xbin
After that I tried to connect to my university's VPN but when it tried to connect, the tablet lost wifi connection and ever since it doesnt connect to any available wifi network!! I manually deleted the OpenVPN binary, but problem remains!
Do you know where could I find the stock ROM for this tablet in order to re-flash it?
Do you have any other proposals? Anything will help!
Thank you very much!!
Sal all,
I cannot find firmware for this tablet. It's a 7inch, dual camera, atm7029 quad core cpu, that doesn't start, but i can write firmware with Actions Pad Product Tool.
The only available firmwares for this type of cpu (atm7029) i was able to find, were from Ainol tablets, but these are not good.(only lights start 1sec)
Can someone help ?
10x in advance !
Hi! There is a similar device firmware from (Russian): (yadi.sk/d/Wku6HWTxKkaKa)
But WiFi and camera other.
System image
Here is the image of the system partition. Dumped with ADB from a working tablet. (512MB)
(mediafire.com/download/roc8870rirvt3hw/actc_system.img)
And this is the image of the recovery partition: (48MB)
(mediafire.com/download/fd30kaio8xb490j/acta_recovery.img)
If you want to see what's inside the images, mount the image in Linux, or use Linux Reader if you're using Windows.
How to use the actc_system.img and acta_recovery.img
Hi, I'm an android newbie needing help. I found this thread while searching for how to deal with a bootlooping Orion TAB-700qc tablet belonging to a friend.
Apparently my friend tried to update the tablet with the wrong update (I'm not really sure what he did), but it went into a bootloop -- it will not get past the "android" screen. I found how to go into the Recovery menu but nothing there would fix the problem. I have downloaded the actc_system.img and acta_recovery.img discussed in this thread, but I need step-by-step instructions for how to use them to get the tablet working again.
Can someone please direct me to instructions that I as a newbie will understand? I have worked a lot with pc's but I have almost no experience with androids.
Thanks,
cmNhu
I have an Azpen A1040, I am fairly new to tablets altogether.
I was trying to use the complete linux installer app to see if I could run Ubuntu on my tablet.
Well, that requires root. I have tried a few things with no success.
But the last one I tried was Vroot, it did NOT root the tablet, but yet, now Vroot is on there and I can not remove it even after doing a Facotry Reset.
I uninstalled Vroot when it didnt work, but then I did a factory reset and noticed there is an icon that looks like the vroot icon but all the text is in chinese.
I dont really need to run linux or root priveleges that bad, but now it bugs me that the vroot app is still there. What is it doing. Is it hurting anything?
Is there an easy way to get rid of it?
The specs of the tablet from the side of the box are
Azpen A1040 10.1" Quad Core Tablet
CPU MT8127 Quad Core Cortex A7
Running Android KitKat 4.4.2
You can find web specs for it at azpenpc.com
I can go in to running apps and do a force stop and disable on the chinese vroot, but I just dont want it to cause spyware or anything else.
Not even sure this is the right forum to post in, but I figure someone will point me in the right direction I hope.
Thanks
Rick (A total tablet newbie) haha
bump
Azpen A1040
Hi Rick, did you figure out how to root this device? I have been struggling for days trying to find a root utility. Thanks!
I'm not doing what you are attempting but.
I found a couple of potential options. That worked for the limited things I was doing.
Cyanogen rooting appeared to work, though it won't allow installation of custom roms since there currently is no support.
Kingoapp I found on CNet, though I don't have any experience with it, it appeared to successfully root the device.
I would have added links but currenlty it appears I'm not allowed to. Google is your friend.
Ren
I got this tablet for my son. Good specs: IPS panel, 2GB RAM, 16GB storage
SOC : Intel atom z2520 , cloverview+ ,
android : 4.4.2 , kernel : 3.10.20 Jul 4 2014 android codename : kot49h IFWI version : F9.F8
I was annoyed by few software bugs (Cut the robe cause instant reboot) and I was looking for a better rom.
Since official Utok site does not offer anything but initial factory software i was looking on internet for same tablet but different brand
I saw Iview i700 and Eboda i200 with same specifications and same looks and I was thinking is the same tablet. I was wrong
Trying to flash Iview software using intel manufacturin flash tool, I messed up partitions and other things.
Now, the tablet at boot show intel logo and do nothing after that, but is accessible via fastboot command.
Because i have messed partitions and I cannot boot to droid recovery I cannot flash original rom which is in zip format recovery flashable.
Please, I need instructions how to fix partition table (partition, start block, size) and how to make a working recovery.
Thank You
FIXED. Intel manufacturing flash tool give timeout on reboot. I was running all fasfboot commands from flash.xml.
After that I was able to flash zip from recovery. Tablet work ok with Eboda i100 and Eboda i200 roms. Also Iview i700 rom works but without cameras. I decided to keep Eboda i200 rom. It is smoother (maybe a placebo).
Utok i700 original rom have a bug which cause continuous touch to be intrerupted during charging. (you canoot drag and move an icon during charging) Eboda roms does not have this bug.
Cut the robe games cause reboot with all roms. (also Angry birds transformers) I am curios if these games works on Iview or eboda devices.
Even if I my knowlege about linux and android is at the ground level I always found useful things here on xda. Great community.
Welcome to my tutorial !
You can find others tutorials related to the Cube i6 :
Install windows 10
Install Android 4.4.4 (Stock & RemixOS)
I received the magnificent AllDoCube i6 Air 3G last week, and i've been struggling since to get updates,
firmware flashing and all of that working, I searched the whole web and the drivers/Firmwares are nowhere to find,
but on some chinese proxy-needed sites sometimes, or baidu which is a pain in the a** to download from.
So I decided to share the ways to update this tablet at all costs (heh, no worries, -NORMALLY- it wont brick)
Disclamer: This process might contain ROM hacking, this is for advanced users.
THIS TUTORIAL HAS BEEN TESTED ON i632GB1537XXXXXXX MODEL, AND WORKS ON IT,
WHEREAS IT HAS BEEN REPORTED THAT i632GB1522XXXXXXX MODEL BRICKED UPON DOING IT,
SO PLASE DO IT CAREFULLY, IF THE INSTALL VERSION IS 202 YOU SHOULD THINK ABOUT IT BEFORE TRIYING AS IT COULD BRICK!
Software included may be subject to copyright.
Flash your device at your own risk. Developer is not responsible for what you do on your device.
What you need:
Cube i6 Air (3G or Wifi)
Flash Drive (256Mo +)
OTG cable
USB Hub (3 Ports recommended)
EFI BIOS Firmware
DOWNLOAD THE FIRMWARE BEFORE STARTING SO EVERYTHING IS AVAILABLE WHEN YOU DO IT
https://drive.google.com/folderview?id=0B8YPw4HjmqNCZktOZy1OTEN2ZVE&usp=sharing
Get on the drive, go to your device folder, select the wanted version inside BIOS folder
What to do :
1.) Start by plugging the usb drive into your computer, and format it to FAT32 using any formatting tool
2.) Now you need to uncompress the downloaded firmware :
you will find a "Firmware_X.X.X" folder inside, take all of its content, and extract it to your freshly formatted drive.
here's what looks like the root of your usb:
3.) Your USB Drive is ready, now just plug the OTG cable to your tablet, plug your HUB onto that OTG
and fill it with your keyboard and the USB Drive just created.
4.) Press power button until you see the screen backlight, when you see it repeatidely smash "Esc" key on the connected keyboard.
You will see the bios 6 square configuration screen.
Hit "Boot Manager" and select your USB in the list.
5.) The tablet should now boot from your USB, booting to a UEFI Shell. Depending on your device, it might be either 64 or IA32.
Now you just let startup.nsh script do the firmware flashing init, it should drive you to a flashing BIOS screen.
6.) Follow instructions on screen and let the tool flash your BIOS automatically.
Once done, the tablet will shut down.
Congrats! You successfully updated your BIOS !
It is my first tutorial, i will post some photos of steps in the future so come back, the guide will be better soon !
Regards,
Max.
Hi,
I have bought the Cube i6 Air 3G a week ago and i'm still waiting for it to arrive.
Have you update the win 8.1 to win 10?
Does everything works correctly?
Regards
re
Hi, I successfully updated the BIOS as of now,
I changed the bootloader animation to nexus one on Cube ROM.
I also manager to boot on Android x86 but it had too many drivers issues.
Still, 4.4.4 stock cube is working and i reflashed to a new partition scheme of 9Go
and i'm currently testing some win10 pen drives for install, will keep you updated.
Édit: oh you were asking about thé tablet? Weil jack has default, charging takes hours, glass is plastic, firmware is pain but hell this is a goodamn good tablet for its price !
regards,
Max
stalker2106 said:
i'm currently testing some win10 pen drives for install, will keep you updated.
Click to expand...
Click to collapse
I achieved installing Win10 x32 Pro on Cube i6 Through hacking WinPE installation environnement, but now i'm struggling finding the drivers. touchscreen, battery and vital things like hd graphics are not working as of now. Will post a tutorial on how to install Win10 in given time when i'll get out of this mess!
My tablet has arrived yesterday.
From what the little i've used it, it has good performance especially in android.
A lot faster compared to my last android tablet (Cube U39GT).
Something i didn't like was the size of the icons and text in android, my next step is to root and change the dpi.
Regarding windows 10, i found in a chinese tablets blog with win 8 and 10 drivers.
I haven't tested it, but as soon as i find it again, i will let you know where to download them from.
You haven't tried the normal win 10 upgrade? From the microsoft icon?
gtbr said:
My tablet has arrived yesterday.
From what the little i've used it, it has good performance especially in android.
A lot faster compared to my last android tablet (Cube U39GT).
Something i didn't like was the size of the icons and text in android, my next step is to root and change the dpi.
Regarding windows 10, i found in a chinese tablets blog with win 8 and 10 drivers.
I haven't tested it, but as soon as i find it again, i will let you know where to download them from.
You haven't tried the normal win 10 upgrade? From the microsoft icon?
Click to expand...
Click to collapse
I did not try anything as i like "stock" versions of my windows, but tonight i got it working all the way !
My cube i6 is running perfectly windows 10 and oh my god what a paradise it is ! The tablet experience got way better onto that version.
Can you try to update from the icon you are talking about ? i'd be curious if it works. anyway, i'm currently writing+uploading for the win10
tutorial for this tablet, so you'll be able to flash it late tonight, or tomorrow.
EDIT: The dpi is correct in android, only the status bar icons and some other are not in correct dpi but that is KitKat issue I guess. still interested in resolving that though. I'm currently hacking android lollipop ROM also, i'll keep you tuned on that. For rooting, i used KingRoot, it worked, but after a reboot, it tells me "root" is wrecked, so i guess there is some investigation to do there, but I was mainly focused on getting windows 10 ENGLISH STOCK version running to share it with you guys.
EDIT2: Still uploading, but tutorial is here: http://forum.xda-developers.com/android/help/guide-how-to-install-windows-10-t3252042 and it should work on any Z37xx powered device. Enjoy !
Hello,
I'm using this tablet from 2 days now. great !
But, i got wifi problem after sleep : wifi chip cut and never found network anymore.
has to reboot, and all goes right.
same in win and android.
Did you hear about this ? many poeple complain about this.
Any trick or advice ? Is this bios correct this ? Is your bios work on i6 3g dual-boot ? (there is 2 bios for dual boot ?...)
Thanks !
Hi,
I've also have the same problem with the wifi.
I usualy disconnect the wifi and reconnect it, but sometimes it doesnt work and have to reboot the tablet.
I've not noticed it in windows but maybe it's because i'm using the tablet a lot more in android.
I've tryed to update to win 10 using the microsoft icon, but i got an error and was unable to complete the upgrade.
gtbr said:
Hi,
I've also have the same problem with the wifi.
I usualy disconnect the wifi and reconnect it, but sometimes it doesnt work and have to reboot the tablet.
I've not noticed it in windows but maybe it's because i'm using the tablet a lot more in android.
I've tryed to update to win 10 using the microsoft icon, but i got an error and was unable to complete the upgrade.
Click to expand...
Click to collapse
Hello, i have such a tablet for now about 6 Months and it is awesome so far (i often use win8.1).
My Tablet has also DUAL Boot with Android 4 and win 8.1 Bing.
I tried to upgrade to win10 but i also got a message that the partition can not be resized by windows. So i cant upgrade to win 10 with the normal tool from microsoft.
Is there any Solution yet to get this to work?
Anyway, i tried to boot from usb (win8.1 / ubuntu / gparted) but it is not working at all. When i try to boot true windows Advanced Boot Options, the BIOS says that there is no USB device.
When i use the EFI Shell to mount the USB Stick i can see that the BIOS has recognized the USB Stick.
I think that is all very strange, but i will try to update the BIOS soon. The serialnumber is not the same as from @stalker2106 but i will try it.
I hope there is a way to get win 10 working, but Ubuntu would be even better for performance.
Greetings from Germany.
tysonpower said:
Hello, i have such a tablet for now about 6 Months and it is awesome so far (i often use win8.1).
My Tablet has also DUAL Boot with Android 4 and win 8.1 Bing.
I tried to upgrade to win10 but i also got a message that the partition can not be resized by windows. So i cant upgrade to win 10 with the normal tool from microsoft.
Is there any Solution yet to get this to work?
Anyway, i tried to boot from usb (win8.1 / ubuntu / gparted) but it is not working at all. When i try to boot true windows Advanced Boot Options, the BIOS says that there is no USB device.
When i use the EFI Shell to mount the USB Stick i can see that the BIOS has recognized the USB Stick.
I think that is all very strange, but i will try to update the BIOS soon. The serialnumber is not the same as from @stalker2106 but i will try it.
I hope there is a way to get win 10 working, but Ubuntu would be even better for performance.
Greetings from Germany.
Click to expand...
Click to collapse
Check windows 10 Post, there is no need to update BIOS to fix this error, your USB has to be in GPT partition style, check answer on the other thread
But usually the bios update should work, as it did on my tablet. But why bother taking risk if you can get it working without it
Hi,
I have sucessfully updated to win10
I have bios 203 in my cube and serial i632gb1510xxxxxxxxxxx, does anybody have tried to update to 206 on such setup ?
What are the chances that I will brick my device ?
I have downloaded latest Cube i6 roms from cube site (may 2015) . There are two bios-es which have to be installed in chronological order.
Shall I do it first, and then try to update to 206 ?
Edit: I was not patient and tried it on my own.I have successfully updated bios and tablet has started to both android and windows
I will perform some functional tests afterwards.
Actual steps :
I have first downgraded bios to 201(provided here )
Flashed bios1 from link provided
Flashed bios2 from link provided
Flashed bios 206 from guide in first post
Edit2:
I have tested basic functionalities like : Gyro-sensors, WIFI, GPS, 3G network and yet everything works like charm.
Maybe a placebo, however I have the feel that android runs like two times faster
I do suggest to update the windows, however I take no responsibility if you will brick your device. Even if the setup is like mine, neither if it differs
Regards
Why do you first downgrade to 201?
What do you mean with bios1 and bios2?
Many thanks and question
Hello Stalker,
I am new here and i want to
thank you for the instructions!
I bought a cube i6 from china.
It is the 'i6 air remix',
So it should have only Android on it.
When it arrived. it didn't function.
The only think that happens is booting to theEFI-shell.
I could switch between Android and Windows in the boot settings.
But Android did not boot.
I have updated the bios with your instructions
now firmware 2.0.6 is installed.
But still i can not boot Android.
I found a few flash tools and android for the cube i6 .
But i don’t know what is the right version flash tool I have to use.
Maybe you have advise or the right android and flash tool in your google drive download area?
Kind regards and many thanks in advance.
jan-netherlands said:
Hello Stalker,
I am new here and i want to
thank you for the instructions!
I bought a cube i6 from china.
It is the 'i6 air remix',
So it should have only Android on it.
When it arrived. it didn't function.
The only think that happens is booting to theEFI-shell.
I could switch between Android and Windows in the boot settings.
But Android did not boot.
I have updated the bios with your instructions
now firmware 2.0.6 is installed.
But still i can not boot Android.
I found a few flash tools and android for the cube i6 .
But i don’t know what is the right version flash tool I have to use.
Maybe you have advise or the right android and flash tool in your google drive download area?
Kind regards and many thanks in advance.
Click to expand...
Click to collapse
The truth is, the 206 BIOS provided is hacked off i6 remix repository from cube, so i guess there is no big deal flashing it on your device as it works on regular i6.
Moreover, you can use any version of the flash tool as long as you flash a correct rom for your device, which i would suggest to download from official cube repository or geekbuying or so.
Android Geecbuying
Hello Stalker,
Ok. Thank you!
I will try Geecbuying.
Hopefully the windows drivers will function.
There isn't a way to flash from USB I suppose?
Greetings
Hi, well, actually, you should flash over USB with à windows computer. MFT by Intel is recommended. I shall make some tutorial about Android installation and partition resizing.
flash and resize partitions
That is super. When you want to do so.
I was indeed wondering or there would be one android partition on the tablet or two partitions (one for android, one for windows).
I also questioned myself how to see that there are partitions.
In earlier times when I was working with a pc, i use F-disk or partition-magic for this kind of work.
But on the tablet I do not have a clue...
So if you could make me wiser on this, I would be very thankful.
Maybe you could boot on some gparted liveusb? Or inside efi shell some commands could help
bluefish007 said:
Why do you first downgrade to 201?
What do you mean with bios1 and bios2?
Click to expand...
Click to collapse
no particular reason, I just wanted to know, which version of bios is in the latest firmware provided by geekbuying
Additional condition in my decision mechanism was that my serial did not match mentioned ones in w10 thread from stalker, so somehow I have used sleepy sloopy logic and tried to minimalize the risk (I know it have no rational reason and logic behind it at all)
Therefore, I tried the ones from geekbuying repository, to be sure to have latest provided from "official source".
greetings
thermoska said:
no particular reason, I just wanted to know, which version of bios is in the latest firmware provided by geekbuying
Additional condition in my decision mechanism was that my serial did not match mentioned ones in w10 thread from stalker, so somehow I have used sleepy sloopy logic and tried to minimalize the risk (I know it have no rational reason and logic behind it at all)
Therefore, I tried the ones from geekbuying repository, to be sure to have latest provided from "official source".
greetings
Click to expand...
Click to collapse
Ok thanks for the answer! So i can upgrade from 203 at 206 at one part or what do you think?