Hello everyone,
I've used Mokee 4.4.4. Rom on my XT910. Then I decided to upgrade it Marshmellow 13. First I tried to install it via BMM then had error status 7. Then tried to set it up via Safestrap and I followed the instructions but install had been faild. Then restarted to device and surely no OP will run cause of wipe. I got error to install any OP as
HTML:
"E: failed to verify whole-file signature, E: Signature verification failed, Installation aborted"
via android system recovery 3e qe2/1. Now the device is wont work any OP and it doesn't turn off. Restart it self over and over.
Here my questions
1. How can I install and up to upgrade again to my device?
2. What does "qe2/1" means. I saw somewhere about root. But I was rooted. And if I need to root again. Which version root files need to be install? What will happen if I root it twice?
3. What will happen if I load to old files?
4. Is it about Kernel? Does any new kernel exist?
5. And what's your advices.
Guys I've less knowledgefor phone. Therefore I need your help. I need detailed explanation to unbrick it. Thanks again.
Regards.
UPDATE: Somehow now I can't reach recovery too. I've just reach AP fast boot menu (flash mode active but battery low, and doesn't charging). Can I send any of fastboot files or is there some file for my stiuation?
UPDATE 2: I've clockworkmod backup BTW. boot_3.0.8-g7198280 and cid_800EB95C-000600CC
UPDATE: Somehow now I can't reach recovery too. I've just reach AP fast boot menu (flash mode active but battery low, and doesn't charging). Can I send any of fastboot files or is there some file for my stiuation?
exilada said:
UPDATE: Somehow now I can't reach recovery too. I've just reach AP fast boot menu (flash mode active but battery low, and doesn't charging). Can I send any of fastboot files or is there some file for my stiuation?
Click to expand...
Click to collapse
op = original poster
you were using clockworkmod? not safestrap?
you cannot charge in AP fastboot mode or stock recovery
you cannot flash firmware with low battery
Booting from AP fastboot to charging mode
If the Device will only boot to AP Fastboot and it says Battery Low
Connect the phone/Device ato a Wall Charger (not PC)
-In AP Fastboot Mode hold Volume down& power buttons at the same time for +10 seconds
- When screen goes black...release power button
-Then IMMEDIATELY press and hold Vol - and Vol+ to boot to Boot Menu.
- In Boot Menu scroll down with volume down to BP Tools, press volume up to select
- Device should boot to Charging Mode with battery icon
- Once battery is charged, try flashing in AP Fastboot again
This will only work if battery charging Firmware is still preset and not corrupted
If Motorola Device will not boot to Charging Mode, a Fastboot cable will be needed.
What is a Fastboot Cable
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my KFFOWI using XDA Labs
sd_shadow said:
op = original poster
you were using clockworkmod? not safestrap?
you cannot charge in AP fastboot mode or stock recovery
you cannot flash firmware with low battery
Sent from my KFFOWI using XDA Labs
Click to expand...
Click to collapse
Firstly thanks for answering
I was use Boot Menu Manager and backup cid via BMM. And then erase BMM and install safestrap on mokee 4.4.4.
phone is able to firmware flashing, at least its not warn at this stage. but I'm afraid to do that with low battery. Also thanks for charging trick but i've been tried that. It's not working for me.
PROBLEM SOLVED! I get factory cable and flash it
Related
Heya,
Today my power buttont got stuck and it was always restarting i watched some videos and i decided to go on without a power button, it was working nice i turned my phone on with a little trick but now i wanted to replace my recovery with TWRP i used SkipSoft Android Toolkit and it said me that the recovery was flashed sucessfull... after that i booted into the recovery via adb (adb reboot recovery) and now i dont got TWRP i just see the Stock Recovery but now my problem is i cant select anyhting because my power button is not working and if i take out the battery -> plug it in + usb calbe it boots directly into the stock recovery...
Now my Question is how can i make the phone boot normal again?
And can i access my phone via my pc somehow via Fastboot or adb?
Thats how my recovery looks like:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thx
incaner said:
Heya,
Today my power buttont got stuck and it was always restarting i watched some videos and i decided to go on without a power button, it was working nice i turned my phone on with a little trick but now i wanted to replace my recovery with TWRP i used SkipSoft Android Toolkit and it said me that the recovery was flashed sucessfull... after that i booted into the recovery via adb (adb reboot recovery) and now i dont got TWRP i just see the Stock Recovery but now my problem is i cant select anyhting because my power button is not working and if i take out the battery -> plug it in + usb calbe it boots directly into the stock recovery...
Now my Question is how can i make the phone boot normal again?
And can i access my phone via my pc somehow via Fastboot or adb?
Thats how my recovery looks like:
Thx
Click to expand...
Click to collapse
You could try a usb jig to get into download mode then use volume buttons to reboot phone ( but I don't know if it would boot to recovery again) or you could try flashing another recovery twrp,philz etc while in download mode.... I'm not too sure if adb works in download mode but you could also try that.
tallman43 said:
You could try a usb jig to get into download mode then use volume buttons to reboot phone ( but I don't know if it would boot to recovery again) or you could try flashing another recovery twrp,philz etc while in download mode.... I'm not too sure if adb works in download mode but you could also try that.
Click to expand...
Click to collapse
Yeah im pretty sure that in download mode the Fastboot commands work but i dont got a usb jig so im asking for an another way...
incaner said:
Yeah im pretty sure that in download mode the Fastboot commands work but i dont got a usb jig so im asking for an another way...
Click to expand...
Click to collapse
The only two ways I know of is (1) Fix power button or (2) Usb jig (only a couple of euro's off ebay) maybe someone else knows a betterway good luck.
tallman43 said:
The only two ways I know of is (1) Fix power button or (2) Usb jig (only a couple of euro's off ebay) maybe someone else knows a betterway good luck.
Click to expand...
Click to collapse
I hope so... ill just wait some weeks until ill go to buy a jig..
but thx for your help
Oops sorry about the caps guys.
So i replaced the digitizer / lcd assembly on an xt912 and before screwing it all back together I wanted to test the lcd.
It's working fine, it's just stuck in M Motorola bootloop and it will go into ap fastboot mode stating PLEASE CONNECT USB etc. No other error...
I don't have the special cable,and keep in mind I don't have it fully assembled.
I do have another xt912 with the battery charged but has a bad lcd as well.
The phone In question - I have no idea if it booted before the lcd broke.
I can't get to recovery mode. Tried numerous times
wondering if I should just use the guts from the other xt912
Can i take out a charged battery from another razr to get this to boot?
Do you think I broke the motherboard?
Do you think this may be stuck in ap fastboot simply because the screws aren't back I yet?
I truly don't feel like downloading sdk kit all over again and flashing this etc etc.
dovedescent7 said:
Oops sorry about the caps guys.
So i replaced the digitizer / lcd assembly on an xt912 and before screwing it all back together I wanted to test the lcd.
It's working fine, it's just stuck in M Motorola bootloop and it will go into ap fastboot mode stating PLEASE CONNECT USB etc. No other error...
I don't have the special cable,and keep in mind I don't have it fully assembled.
I do have another xt912 with the battery charged but has a bad lcd as well.
The phone In question - I have no idea if it booted before the lcd broke.
I can't get to recovery mode. Tried numerous times
wondering if I should just use the guts from the other xt912
Can i take out a charged battery from another razr to get this to boot?
Do you think I broke the motherboard?
Do you think this may be stuck in ap fastboot simply because the screws aren't back I yet?
I truly don't feel like downloading sdk kit all over again and flashing this etc etc.
Click to expand...
Click to collapse
If AP fastboot doesn't say low battery, then it's not a battery issue, and a fastboot cable is not needed.
But it's not uncommon that firmware needs to be flashed after a hardware repair.
See Flashing with RSD Lite in the index
http://forum.xda-developers.com/showthread.php?t=3023837
[INDEX] Motorola Droid Razr Development (2015)
Sent from my XT907 using Tapatalk
Much appreciated . YeS it does say low battery sorry about that
dovedescent7 said:
Much appreciated . YeS it does say low battery sorry about that
Click to expand...
Click to collapse
Try Booting from AP fastboot to charging mode
If the Device will only boot to AP Fastboot and it says Battery Low
Connect the phone/Device ato a Wall Charger (not PC)
-In AP Fastboot Mode hold Volume down& power buttons at the same time for +10 seconds
- When screen goes black...release power button
-Then IMMEDIATELY press and hold Vol - and Vol+ to boot to Boot Menu.
- In Boot Menu scroll down with volume down to BP Tools, press volume up to select
- Device should boot to Charging Mode with battery icon
- Once battery is charged, try flashing in AP Fastboot again
This will only work if battery charging Firmware is still preset and not corrupted
If Motorola Device will not boot to Charging Mode, a Fastboot cable will be needed.
http://goo.gl/QllP1j
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my XT907 using Tapatalk
this i all i can get to guys
It's a bit of a strange problem, I'll start from the start.
I tried to update my Z2 with a new rom but I got stuck with my recovery saying that the rom was for a diffrent device (It incorrectly identified my device as a "Leo" instead of "Sirius")
I found a diffrent version of TWRP that suposedly fixed this issue but when I flashed it in fastboot all I got was a boot loop with the sony logo. It doesn't get to the point where the LED lights up and you press the volume button to get into recovery.
I tried to go back into fastboot mode/download mode to try and force it to boot into recovery that way, this is when my battery went flat and the real fun began.
When I try to charge it straight off a wall charger It would automatically boot up to the sony logo and get stuck in it's boot loop.
The problem is that this boot loop seems to drain the battery faster than I can charge it. After awhile the screen goes black with a red LED indicating a flat battery and as soon as it gets enough charge it'll try and boot again.
I can get it into download mode only if I let it charge for awhile and then go through the steps using the wall charger and not the PC, this obviously doesn't do me any good but at least it is possible to access this mode if I can get enough juice back in it.
Is there anyway of stopping it from trying to boot while I'm charging it?
Any suggestions would be greatly appreciated, I'm at a loss with what to try next.
maggot11 said:
It's a bit of a strange problem, I'll start from the start.
I tried to update my Z2 with a new rom but I got stuck with my recovery saying that the rom was for a diffrent device (It incorrectly identified my device as a "Leo" instead of "Sirius")
I found a diffrent version of TWRP that suposedly fixed this issue but when I flashed it in fastboot all I got was a boot loop with the sony logo. It doesn't get to the point where the LED lights up and you press the volume button to get into recovery.
I tried to go back into fastboot mode/download mode to try and force it to boot into recovery that way, this is when my battery went flat and the real fun began.
When I try to charge it straight off a wall charger It would automatically boot up to the sony logo and get stuck in it's boot loop.
The problem is that this boot loop seems to drain the battery faster than I can charge it. After awhile the screen goes black with a red LED indicating a flat battery and as soon as it gets enough charge it'll try and boot again.
I can get it into download mode only if I let it charge for awhile and then go through the steps using the wall charger and not the PC, this obviously doesn't do me any good but at least it is possible to access this mode if I can get enough juice back in it.
Is there anyway of stopping it from trying to boot while I'm charging it?
Any suggestions would be greatly appreciated, I'm at a loss with what to try next.
Click to expand...
Click to collapse
Flash stock ftf with flashtools
Or flash a kernel that has built-in recovery (like elite kernel)
And flash an stock based rom to revive you phone then flash anything you want
raminta said:
Flash stock ftf with flashtools
Or flash a kernel that has built-in recovery (like elite kernel)
And flash an stock based rom to revive you phone then flash anything you want
Click to expand...
Click to collapse
I have attempted this but I can't get it to boot into download mode to flash a stock firmware without getting more of a charge in it.
I have ordered charging cable that connects to the magnetic dock connection and hopefully that will let me keep it charging while flashing.
maggot11 said:
I have attempted this but I can't get it to boot into download mode to flash a stock firmware without getting more of a charge in it.
I have ordered charging cable that connects to the magnetic dock connection and hopefully that will let me keep it charging while flashing.
Click to expand...
Click to collapse
First use Xperifirm from flashtool to download D6503_23.5.A.1.291_1281-9715_R4D.ftf
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Let it download and then use the little "OFF" Button by the Sim card tray. It'll turn phone off completely. Then plug USB Cable into phone and hold Volume UP while plugging USB Cable into PC.
Then use Flashtool to flash the firmware you downloaded.
Hello friends, I hope you are well. I am writing to everyone to see if anyone can help me with this big problem.
Yesterday install the Rom Pixel Experience, all good, all the steps to perfection and others, had microSD at that time so flash the boot.img by Fastboot. It seems to install the Boot.img in the Recovery TWRP partition, or something like that. Because I do not have the Recovery either, when I try to go to the recovery, the window "Bootloader Unlocked" appears, but it does not take me anywhere, only to the boot of the rom, it is something very strange and the truth scares me. I clarify: I can not access the Fastboot, nor the download mode, nor the recovery, because it does not.
There will be another way: ????
PLEASE IF SOMEONE CAN HELP ME, FIND ANOTHER METHOD TO ENTER THE FASTBOOT OR DOWNLOAD MODE, THE SOLUTION THAT WORKS WILL PAY ME WELL TO THE PROPONGA, PLEASE, I DO NOT WANT TO LOSE MY MOBILE, I BUY IT WITH A LOT OF EFFORT.
Last night I dawned on the boot logo, until it was completely downloaded and at this moment it continues to do so ... By GOD!
When trying to enter the Fastboot or download mode, it takes me here:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Image extracted from: https://www.tomshw.it
Then he starts loading the rom and stays there all the time .:
Image extracted from: https://www.tomshw.it
I can not access Fastboot, nor download mode, nor recovery, because it has disappeared. There will be another way to enter the Fastboot or download mode, because the phone actually woke up until I wake up today and was even charged. PLEASE.
Hey, sorry for your sad state. Following process worked for me when I got stuck yesterday like that.
1. Connect your phone to PC ( make sure adb/fast boot is setup)
2. Hard reboot your phone with power plus volume down button.
3. As soon as your phone turns off, press volume down only and keep it pressed till you enter fastboot.
4. After this phone should be recognised in PC and you should be able to boot in TWRP using fastboot.
ZestyManu said:
Hey, sorry for your sad state. Following process worked for me when I got stuck yesterday like that.
1. Connect your phone to PC ( make sure adb/fast boot is setup)
2. Hard reboot your phone with power plus volume down button.
3. As soon as your phone turns off, press volume down only and keep it pressed till you enter fastboot.
4. After this phone should be recognised in PC and you should be able to boot in TWRP using fastboot.
Click to expand...
Click to collapse
Hope this works for you @Yeriorlando. @gimpy1 had a similar issue when installing Havoc ROM. Part of the problem seems to be when installing the custom kernel?
gimpy1 said:
It was operator error (generally is) on my part, I'm sure. The only thing I did different that I can remember is installing the 9.0 boot image in twrp differently. I installed it in the recovery option first (intentionally, should not have), instead of ticking only the boot choice. I did not untick the recovery option (should have never ticked it in the first place, but I was trying to correct a problem on the ROM, and misread a post).
Click to expand...
Click to collapse
He was able to reinstall TWRP using fastboot.
gimpy1 said:
Thx, Chaz. I pulled out my printed instructions from your post, and once I was able to get my device recognized (that did take a couple of tries), reinstalling twrp was pretty easy.
I'm back in business thanks to you.:good:
Click to expand...
Click to collapse
IF you still can't after the suggestion at top, maybe @SGCMarkus or @runningnak3d have some tips?
Unless you have an H932, then if you get the error that: "Your device software can't be checked for corruption" then you have fastboot. It is literally impossible to have that message on a WTF rooted phone and NOT have working fastboot.
So, as @ZestyManu said -- make *sure* your phone is powered off. If you have to let, the battery die. Then hold vol down + plug in the USB cable (no need to touch the power button) and you will enter fastboot.
-- Brian
Thank you all. I have solved the problem in a super crazy way, to pure ADB, not fastboot .... Pure ****ing adb ... Hehehehe. Thanks to @ChazzMatt
Ok i need some emergency help please: what i did:
Downloaded stock rom (exact version number of my Infinix Note 10i X659B) X659B-H696AvAw-R-OP-210330V152
Grabbed boot.img, placed on phone folder,
installed magisk apk, patched with magisk apk and put that patched-img to the folder in my PC.
Got minimal adb tools, used adb reboot bootloader to put phone on fastboot (saw fastboot screen on phone) did:
fastboot flash boot_a patch-boot.img
fastboot flash boot_b patch-boot.img
(renamed the file to patch-boot.img for convenience)
Now phone is stuck booting
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i only see the "Infinix" start up screen, then a message: Orange State: Your device has been unlocked and can't be trusted
Your device will boot in 5 seconds
to be fair that message appeared when i unlocked the bootloader, and beside the data wipe, the phone worked just fine
So where i think i screwed up is by installing it on boot_b too, (guide i followed said that i should also patch boot_b if my phone have a/b system (which it does, also magisk app also told me)
So what i can do? I cant seem to be able to put my phone down on fastboot again to try to patch either the stock image or reflash the whole phone. Or i just bricked my brand new phone? :'(
With Android having an A/B image partition layout the user-runable Android is that in slot A. Slot B is only used to temporarily store OTAs: When update process successfully ends then at phone's reboot whole slot B gets copied into slot A and finally device gets booted into updated slot A. My POV: It's always an idiocy to flash a patched boot.img to slot B.
To get rid off of all modifications you applied so far you're recommended to re-flash phone's Stock ROM.
jwoegerbauer said:
with Android having an A/B image partition layout the working Android is that in slot A. Slot B is only used to temporarily store OTAs: When update process successfully ends then at phone's reboot whole slot B gets copied into slot A and finally device gets rebooted ( into updated slot A ). My POV: It's always an idiocy to flash a patched boot.img to slot B.
To get rid off of all modifications you applied so far you're recommended to re-flash phone's Stock ROM.
Click to expand...
Click to collapse
How you can recommend i reflash the whole rom? I cant seem to find how to get the phone into another state. Volumen Up + Power does nothing, phone keeps trying to reboot.
Volume Down + Power does nothing either
Volume UP+Down+Power keeps the screen off, but i can hear windows connecting/disconnecting every 10 seconds or so. so how i connect it to, lets say, SP Flash Tools (considering is a MTK device)?
Well tried to do it with SP Flash Tools, but after trying to "Format All+Download" with all the checkboxes subsystems selected, i get a "auth file needed" error
Didn't find any of that in the firmware i downloaded :c
You need mtk bypass tool for that
mgdark said:
Well tried to do it with SP Flash Tools, but after trying to "Format All+Download" with all the checkboxes subsystems selected, i get a "auth file needed" error
Didn't find any of that in the firmware i downloaded :c
Click to expand...
Click to collapse