hi to all
as mentionned in title here is a good hint how to get your mediapad working again without any problem
symptome of the problem
1- tablet cant be flashed using normal way (sdcard)
2- tablet is in qualcomm dload 9006 mode.
3- any other software related problem.
if you are in any of the three above situations and you are so angry because of this then use this to get your tablet alive again
procedure step by step:
1- download attached rar file and extract his contents you will see many files like this
- 8660_msimage.mbn
- EBR0.bin
- MBR0.bin
- MPRG8660.hex
- partition.xml
- patch0.xml
- rawprogram0.xml
now it surely inspire a lot of people who know the use of those files.
anyway.
2- download any firmware for your tablet ( same used in SD card methode) and extract the content of update.zip in the same directory with above files.
3- download eMMC_DL_Tool
4- if your tablet is in qualcomm dload 9006 from the first time the you dont need this step otherwise do the following to put it in qualcomm mode.
press at the same time volume up + volume down and insert usb cable then wait for approximately 20 second your pc will detecte tablet in qualcomm dload 9006 (install driver if not installed).
5- now setup port on eMMC_DL_Tool with your connected tablet and use it to download safly your firmware and revive your tablet again.
good luck to all
Huawei MediaPad 10 S-10 201u
HELP, I have a problem with my logo and I can not even get a factory reset ......and the battery is running out, it's just a fastboot menu. Huawei MediaPad 10 S-10 201u, no hard reset in logo Huawei MediaPad 10 Link...Batery low???
Related
Dear Developers,
I have Ainol Numy 3G AX9 P97.
But there is always adds are poping up and tablet using is quite difficult.
We need a custom ROM for it. (MIUI rom or any android custom rom)
We did not find any other ROM for it.
So if you have/know where can I found this then please give me link or if you have then please help me with this ROM.
Thanks in advance.
================================================================================================================================================================================================================================================
We have found one link but not Download links are are working now: 4pda.ru/forum/index.php
After flashing the tablet is not charging, does not turn on the computer is not detected. The solution for such bricks include:
1. Remove the back cover plate.
2. Turning off the power connector.
3. Unpack firmware somewhere on your computer.
4. Turn SP Flash Tool 5.14 and set the path to the file from a folder with MT6582_Android_scatter unpacked firmware (see para. 3)
5. Expose setting Format All + Download and hit Download.
6. Hold down the Volume + pressed connect the USB and wait until the flashing process will start. (The buttons do not go!)
7. As soon as you see a yellow band of interest on the firmware download, you can release the Volume + and wait for the end of the process.
8. After the firmware disable USB, connect the power connector of the battery and turn our device for verification.
9. Put the cover back.
As I said, flashing a site Ainol not work and leads to a brick (3 times sewed, 3 times okirpichil). I solved this problem by replacing preloader.bin of the new version on preloader.bin from the previous version, which is stitched without any problems, and then packed RABOCHUYUYU latest firmware for our tablet did re-initialization of memory + 2GB USRDATA (instead of 1 GB for applications will be allocated 2 GB and there is no fault with the lack of space). Spread the firmware for the members of the forum.
To flash mode Firmware Uprade through SP Flash Tool (for those who okirpichil: see. The instructions above)
Do not forget to make backup NVRAM!
Ainol_AX9_2014.09.05_2GB
Attached file SP_Flash_Tool_v5.1452.00.000.rar (24,67 MB) --> no link
Here CWM recovery for our animal. Put through Mtk Droid Tools.
Download CWM recovery
Attached file MtkDroidTools.rar (9.97 MB)
1. Turn the tablet in debug mode via USB. (Settings for developers)
2. Set the Root rights (Annex Framaroot to help)
3. Start the MTK Droid Tools, connect the USB cable to the plate.
4. Wait for the connection (in the corner of the box should be lit green), and your device must be recognized.
5. Go to the tab root, backup, recovery.
6. click on the button Recovery and Boot.
First, it prompts you to specify the path to the boot.img, but we we press Cancel, and then it asks you to specify the path to recovery.img and we specify the path to my file and hit ok.
7. Turn off the tablet and go in through rekaveri kombanatsiyu On. and Volume +
Attached file recovery.img (5,33 MB)
Please add information to the cap.
So recently a tried to put a new ROM on my LeEco Le Max 2 and bricked it. It does not allow me to boot into recovery mode, but i can get into the Fastboot mode. How do I fix my phone?
I followed this guide: https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/
It worked for me.
After installing the Qualcomm drivers, open the device manager, launch Flash One, connect Le Max 2, push volume +/- and power (there was no screen activity but in device manager "Qualcomm QDLoader " became visible on COM 3), select device in Flash One (my case COM 3) and do as instructed. It takes a while but it works.
Heyyo, if you can still get into fastboot? You probably just need to reflash TWRP.
https://forum.xda-developers.com/le-max-2/how-to/protocol-backup-stock-rom-flash-stock-t3517151
KyleLockey said:
So recently a tried to put a new ROM on my LeEco Le Max 2 and bricked it. It does not allow me to boot into recovery mode, but i can get into the Fastboot mode. How do I fix my phone?
Click to expand...
Click to collapse
just install twrp by fasboot flash recovery recovery.img
push downloaded firmware by push command you can search how to push zip file or past it in otg and install firmware by twrp.
twrp will install firmware it takes 15 to 20 minutes...
your phone will boot normally
LeEco Le Max 2 ( DEAD PHONE and No sing of life when plugged to charger)
I have the same issue black Screen and No Respond from Phone and NO LED
When connect to PC, I hear sound that its connected, and became visible on COM 3 and no respond from the phone
I have tried the following: tools
1. ADB-
a. "adb devices" it says something is there
b. "fastboot boot RECOVERYNAME.img" its say finding device and noting happens
2. Flash one 1.9
a. I Select File that are needed, after pushing flash 5 min Later nothing happens and it says I dont have the correct recovery files
3. LeEco Tool kit: this Kit Is an easy version of ADB
Phone is DEAD and led . I will take suggestions
To bring your phone back from the dead ( Black screen , No LED, No Respond)
What you will need the Following:
1) A Windows computer - OS does not matter
2) FlashOne 1.9 program (
a) need this program to Flash zip files to your phone
3) QFIL files (LeMax2QFIL.zip) for X820 or whatever is that model (Find the latest zip file) these are the files that will bring your phone back from the dead
4) Qualcomm driver's need to access your phone (Qualcomm HS-USB QDLoader 9008 (COM ...)"
----------------------------
Unzip the the following in a folder
-FlashOne 1.9
-LeMax2QFIL.zip
-Qualcomm
----------------------------
1. Open Qualcomm folder and install the program for your COM slots
2. place FlashOne 1.9 folder at c:/ drive
2. Rename The Qfil.zip From (LeMax2QFIL.zip) to (a.zip) and place it inside Flash one 1.9 program at C :/ Drive
---------------------------------------
1. GO to FlashOne 1.9 folder at your C:/ Drive open it and Right click “main.exe”. (Run it as an Administrator)
2. Once you've opened the flash-tool you'll see
a. "Flash Type".
a1. select "Qualcomm - flash dead phone".
3. Connect the Phone to PC.
a. Your PC will make a sound of Disconnection and Re-connection of an USB peripheral ( if not charge your phone and restart the process)
b. Click “Refresh button” next to “Select Device”. Here your Le Max 2 will show up but in COM Number (ComXX)
4. Select File "a.zip" from the folder where it is saved
a. Press "Flash" in the lower part of the window
5. Installation can take anywhere between 10 to 20 minutes. ___Have Patience.
6. Once completed, disconnect the phone and power it up
If you need any of the tools above, please ask for it, Since I am new I am unable to post and links to any replies at this time
This is an unbrickable phone
if the method can not unbrick your phone, you can try the firmware , hope help you .
https://www.needrom.com/download/le...ultilanguage-rom-unbrick-phone-qfil-fastboot/
Hi all as the title suggests is there anyone who has a fairly detailed Unbricking guide or a way to reflash the stock meizu software via fastboot, QFIL or anything that has worked.
The current problem I face is I have the m6 note with Chinese firmware and wanted to flash global firmware via flash fire as the TWRP APK didn't work for me . I can't enter recovery and fastboot gives me a failed message (remote: partition flashing is not allowed ).
Thank you in advance
its for m3 but you may try http forum flymeos com/forum.php?mod=viewthread&tid=35810&highlight=unbrick
also this one for our phone http://forum flymeos.com/thread-38489-1-1.html
This one is from original flyme os forum FAQ
Q: Recover soft-Bricked device (for those can't access the system)
A: Access the Recovery mode:
1.Turn Off the Phone (ensure that you have more than 20% battery)
2.Press and Hold Volume UP + Power
3.release as soon as you see the Meizu logo
Download firmware from http://www.flymeos.com/firmware.html, Copy the update.zip (naming is important) on your phone and select System Upgrade + Clear Data. As soon as it's connected a "Recovery Drive" will pop up. Now, connect your phone (still in Recovery Mode) to your Windows PC. As soon as you are there, you are just fine.
hi thanks @consumimur , but the first method is for mediatek devices isn't it? The second method doesn't work for me at all because i can't enter my recovery , i need some sort of flashing too QFIL doesn't work for well at the the one i tried (2.0.0.5) as it ask for "Rawprogram.xml" and "patch* " which is not in the update.zip
Yusuf.T said:
hi thanks @consumimur , but the first method is for mediatek devices isn't it? The second method doesn't work for me at all because i can't enter my recovery , i need some sort of flashing too QFIL doesn't work for well at the the one i tried (2.0.0.5) as it ask for "Rawprogram.xml" and "patch* " which is not in the update.zip
Click to expand...
Click to collapse
http://4pda.ru/forum/index.php?showtopic=843179&view=findpost&p=69341915
New https://www.movilesdualsim.com...oros/meizu-m6-note-sd625.1222/
Enviado desde mi M6 Note mediante Tapatalk
i think thats what you are looking for
https://firmwarefile.com/meizu-m6-note-m1721
Folks, today I've had the fortune to brick (corrupting the devinfo partition, screwing up recovery and OS boot as well) and unbrick (stock recovery and OS restored and working perfectly) my Meizu M6 Note without opening it up. If anyone is still interested, instructions are here:
https://forum.xda-developers.com/showpost.php?p=77964079
Hi, I have a problem with my m6 note. I have WIFI MAC address between 2: 00: 00: 00: 00: 00 and I can not turn on wifi. I found a solution to upload persist.img and this should help. However, I can not find the persist.img file anywhere. Can you help?
consumimur said:
This one is from original flyme os forum FAQ
Q: Recover soft-Bricked device (for those can't access the system)
A: Access the Recovery mode:
1.Turn Off the Phone (ensure that you have more than 20% battery)
2.Press and Hold Volume UP + Power
3.release as soon as you see the Meizu logo
Download firmware from http://www.flymeos.com/firmware.html, Copy the update.zip (naming is important) on your phone and select System Upgrade + Clear Data. As soon as it's connected a "Recovery Drive" will pop up. Now, connect your phone (still in Recovery Mode) to your Windows PC. As soon as you are there, you are just fine.
Click to expand...
Click to collapse
thank you so much for this @consumimur. It saved me from going down a rabbit hole, after getting a bootloop with meizu x8 m852h, having followed these instructions:
Meizu X8 - Обсуждение - 4PDA
Meizu X8 - Обсуждение, Смартфон, 6.2"
4pda.to
OP:
ttps://4pda.to/forum/index.php?showtopic=965227
author: 555frost555
Download (litter, files lost) archive and unpack to the root of the C drive
Charge your phone at least 50%
Disable signature verification using the following instructions:
For WINDOWS 7-8: Run Command Prompt as administrator, execute two commands in turn and reboot
Code:
bcdedit.exe -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit.exe -set TESTSIGNING ON
For WINDOWS 10: press start, hold shift, press shutdown computer. The computer will boot into a recovery screen. Select custom boot options and disable driver signature verification.
PS personally, I recommend installing on win7 or 8.1 - less haemorrhoids
Install QFIL
Install Qualcomm 9008 driver
Install standard drivers from the phone (connect to the computer in the CD-drive mode and install from there)
Run QFIL and select "flat build"
Select programmer: "prog_firehose_ddr.elf"
Select XML: "rawprogram0.xml"
Select XML: "patch0.xml"
Turn off the phone
Clamp VolUp + VolDn + Power
The Meizu icon appears, followed by a black screen. The keys can be released.
Connect your phone to your computer. It should be detected as Qualcomm 9008.
Press DOWNLOAD
QFIL is very moody about the system and drivers. If you did everything correctly, but you get an error while flashing, then you need to try it on another computer. Preferably on where windows was recently installed ...
When FINISH is written in QFIL, you can turn off the phone and restart it by holding down the power key until it vibrates.
For WINDOWS 7-8: Run Command Prompt as Administrator, execute two commands in turn and reboot
Code:
bcdedit.exe -set loadoptions ENABLE_INTEGRITY_CHECKS
bcdedit.exe -set TESTSIGNING OFF
I did this with the QFIL archive linked in https://4pda.to/forum/index.php?act=findpost&pid=88712568&anchor=Spoil-88712568-6
and received a bootloop on meizu x8 m852h. Then I did what @consumimur wrote
I did this on a windows 10 machine
I did this on a w10 machine
This is unbrick firmware. Enjoy free. Download Unbrick Meizu M6 firmware.
If you are try to install twrp/cwm in Huawei Ascend G700 U10 and failed dont worry, this solution works 100%!
Required files:
1.Android CDC Driver
2.SP Flash Tool
3.Firmware (this firmware is modded only for Bootload fix!)
drive.google.com/drive/u/0/folders/1kKDIObr5sHcBCjBlZNwGH2idQcigjV3v
How to do:
1.Install Android CDC Driver.
2.Open SP flash Tool.
3.Press on Scatter-loading, navigate to folder Firmware and open MT6589_Android_scatter_emmc.
4.Uncheck all exept BOOTIMG and RECOVERY.
5.Press Download.
6.When it finish, take your Huawei phone, take out battery, put usb and hold Power button + Volume Down button.
7.SP Flash Tool will recognise him automaticaly and will start to install boot and recovery.
8.Thats it your phone will be fixed
Chears
All of us knows that we upgraded to OxygenOS 12 stable or beta but OnePlus didn't given roll back package so who are stucked on OOS 12 can now downgrade using this process.
This is downgrade process by using relive dvd based MTK client Tutorial booted using Pendrive on window pc.
Remember to follow this you need some patience and flashing knowledge and risk of bricking device if u don't follow correctly.
If you cannot bear this in mind then please don't follow blindly
This process also works for eu regions if you flashed indian open beta oos12 file.
Windows based MTk client application is available and its very good option but for me it's not detecting the the device so I will create another tutorial soon using that tool.
Requirements:
1) PC with all fastboot ,adb drivers and mediatek vcom drivers installed
3) Pendrive or use separate partation on hard drive
4) download files given below
5) patience and some flashing knowledge is must
Download MTk client relive dvd:
https://androidfilehost.com/?fid=15664248565197177367
Mirror link:
https://drive.google.com/file/d/10OEw1d-Ul_96MuT3WxQ3iAHoPC4NhM_X/view?usp=sharing
How to flash relive dvd in pendrive using Rufus that tutorial can be found here:
Relock bootloader and get stock recovery oneplus nord 2 Indian/EU: works for any MTK device
Note: This process is shown for OnePlus Nord 2 and work for any MTK device just replace files as per your model you need to Serch for that) Credits @Raygen @TheWing After relocking bootloader you can do safety net pass check to confirm by...
forum.xda-developers.com
Download Oxygen OS 11 firmware backup choose latest as per your device model
Indian DN2101 EU DN2103 and PACMAN)
Extract and save to pc harddrive/relive dvd in PC/laptop
https://gist.github.com/Giovix92/c7e69123dbc51adf3f3a26f9c3c0208e#backup-zips-links
DOWNLOAD PRELOADER BIN FILE:
INDIAN (copy and save it to pc in separate folder)
https://drive.google.com/file/d/1E2yL8uJA7tubHHlqHKkHkJffcCUrllAl/view?usp=drivesdk
EU regions (unzip and take out bin file)
https://forum.xda-developers.com/attachments/preloaderdump_stock-zip.5597685/
Notes :
1)Keep one Harddrive on pc free of space above 30GB
2) you will loose all data so keep full backup
Disclaimer
I am not responsible for anything happens to your device your device your responsibility!
Steps:
A) Baking up the OOS 12 firmware and preloader
1) first keep your pc powered off
2) connect relivedvd iso pendrive and power on the pc and while booting repeatedly press boot menu key fo your pc model you will get about boot menu key info in google search
3)u will get boot menu from there select connected usb pendrive
4)now u will see mtk client relivedvd boot option select first one
5)phone will boot to xubuntu which is nothing but mtk client ready to go environment
6)Now go to file manager on dextop create backup folder to backup your current oos12 name it as you wish.
Remember create this folder in HDD which has more than 30gb space
7) create another folder to take backup of preloader of oos12 in same folder.
8)now trasfer extracted oos11 firmware in same hdd which has all images file.
9)now create seperate folder to save preloader of oos 11 and trasfer the boot1.bin( preloader file) in this folder which we have to flash later.
10)now open mtk client app which ia available on pc dextop
11) take phone in hand power off it, connect one end of usb cable to pc don't connect another end to phone first long press vol up+ down and connect phone to pc keep buttons pressed Until some connection activity of moving circle will be seen in mtk client
12) if it's seen immediately release the buttons now you gets read Partation tab in the mtk client
13)tap on read Partation and select the backup folder you created in hdd.
While selecting the hdd you need to go to computer>media> user there u see all hdd select the hdd where u placed the backup folder.
14) immediately after selecting the folder backup starts ,you will see progress bar at bar in mtk client this will take 25min or more out 2 hr as per your pc model
15)now you gets 100% notification after backup completion now go to flash partation tab and select read preloader
Now select the folder you created to save the preloader file and tap save button from to right corner.
Your preloader for oos12 will be get saves to pc
B) flagshing oos 11 firmware
1) Now go to write partation tab and tap select from directory button
And locate the extracted partation folder.
all paratations automatically gets settled to respective tab in mtk client.
Remember some partation are empty like nvdata, protect and persist don't worry still our device will work
2)tap write partation tab and flagshing starts once done you get 100% progress bar in mtk client.
3)now we need to falsh preloader go to flash tool tab now tap write preloader
Select the preloader from folder where u saves the downloaded from download section.
4)tap open tab from top right corner but this time nothing happens in progress bar and mtk client will gets freeze.
Don't worry our work has done here.
5)now remove usb cable from device and long press vol up+power
6) phone will boots to recovery there tap wipe and format data and your phone will boots to oos12
7) check about phone and see all things working or not like FP, CAMERA etc.
Very imp trouble shooting :
After falshing oos 11 firmware and when you boots if you gets corrupt boot image screen then long press vol up+down +power
Phone will boot to fastboot mode
Now open terminal app on dextop ( or use windows cmd if it's not detecting)
Then reboot back to fastboot type
Fastboot flashing unlock
Press vol up on phone
Now in terminal type fastboot reboot
hello there, i was following your tutorial but i have encountered into a major issue.
MTK Client is stuck at connection handshake error, retrying
i am using it MTK live cd 4 from the link you have provided. Phones get detected and nothing further from there, i have error going back to Bootloader ''the serial not match and fastboot verify fail'' and i cant downgrade my phone to OOS 11.
I have tried almost everything but its not letting me to connect it with MTK client
Try easier way : Click (new current method)