So recently a tried to put a new ROM on my LeEco Le Max 2 and bricked it. It does not allow me to boot into recovery mode, but i can get into the Fastboot mode. How do I fix my phone?
I followed this guide: https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/
It worked for me.
After installing the Qualcomm drivers, open the device manager, launch Flash One, connect Le Max 2, push volume +/- and power (there was no screen activity but in device manager "Qualcomm QDLoader " became visible on COM 3), select device in Flash One (my case COM 3) and do as instructed. It takes a while but it works.
Heyyo, if you can still get into fastboot? You probably just need to reflash TWRP.
https://forum.xda-developers.com/le-max-2/how-to/protocol-backup-stock-rom-flash-stock-t3517151
KyleLockey said:
So recently a tried to put a new ROM on my LeEco Le Max 2 and bricked it. It does not allow me to boot into recovery mode, but i can get into the Fastboot mode. How do I fix my phone?
Click to expand...
Click to collapse
just install twrp by fasboot flash recovery recovery.img
push downloaded firmware by push command you can search how to push zip file or past it in otg and install firmware by twrp.
twrp will install firmware it takes 15 to 20 minutes...
your phone will boot normally
LeEco Le Max 2 ( DEAD PHONE and No sing of life when plugged to charger)
I have the same issue black Screen and No Respond from Phone and NO LED
When connect to PC, I hear sound that its connected, and became visible on COM 3 and no respond from the phone
I have tried the following: tools
1. ADB-
a. "adb devices" it says something is there
b. "fastboot boot RECOVERYNAME.img" its say finding device and noting happens
2. Flash one 1.9
a. I Select File that are needed, after pushing flash 5 min Later nothing happens and it says I dont have the correct recovery files
3. LeEco Tool kit: this Kit Is an easy version of ADB
Phone is DEAD and led . I will take suggestions
To bring your phone back from the dead ( Black screen , No LED, No Respond)
What you will need the Following:
1) A Windows computer - OS does not matter
2) FlashOne 1.9 program (
a) need this program to Flash zip files to your phone
3) QFIL files (LeMax2QFIL.zip) for X820 or whatever is that model (Find the latest zip file) these are the files that will bring your phone back from the dead
4) Qualcomm driver's need to access your phone (Qualcomm HS-USB QDLoader 9008 (COM ...)"
----------------------------
Unzip the the following in a folder
-FlashOne 1.9
-LeMax2QFIL.zip
-Qualcomm
----------------------------
1. Open Qualcomm folder and install the program for your COM slots
2. place FlashOne 1.9 folder at c:/ drive
2. Rename The Qfil.zip From (LeMax2QFIL.zip) to (a.zip) and place it inside Flash one 1.9 program at C :/ Drive
---------------------------------------
1. GO to FlashOne 1.9 folder at your C:/ Drive open it and Right click “main.exe”. (Run it as an Administrator)
2. Once you've opened the flash-tool you'll see
a. "Flash Type".
a1. select "Qualcomm - flash dead phone".
3. Connect the Phone to PC.
a. Your PC will make a sound of Disconnection and Re-connection of an USB peripheral ( if not charge your phone and restart the process)
b. Click “Refresh button” next to “Select Device”. Here your Le Max 2 will show up but in COM Number (ComXX)
4. Select File "a.zip" from the folder where it is saved
a. Press "Flash" in the lower part of the window
5. Installation can take anywhere between 10 to 20 minutes. ___Have Patience.
6. Once completed, disconnect the phone and power it up
If you need any of the tools above, please ask for it, Since I am new I am unable to post and links to any replies at this time
This is an unbrickable phone
if the method can not unbrick your phone, you can try the firmware , hope help you .
https://www.needrom.com/download/le...ultilanguage-rom-unbrick-phone-qfil-fastboot/
Related
Recently while flashing alpha version of MIUI marshmallow on my Mi 4w, my phone got completely bricked. Complete brick in the sense, it won't turn on, neither charge nor show any led indication. This guide should work on other phones also.Let's start:-
1) Although it seems like your phone wont turn on, your phone is actually working, it's just it wont show anything on the screen(no display).
Make sure your phone is charged properly(it will charge even if the led doesn't show any indication).
2) Download and install Mi flash tool and then Fastboot file of your device. http://en.miui.com/a-234.html
3) Unzip the fastboot image, a folder containing flash all.bat should appear if not, extract the extracted file again. Winrar should work fine.
4) Now open Mi flash tool(as administrator) and select the fastboot folder from Mi flash using browse option and also select the proper fastboot script according to need.
Note: Flash_all.bat will completely erase your internal storage.
5) Now press volume down(-) and power key to enter into fastboot. Note: it won't show any visual whatsoever but it'll work.
6) Connect your phone to your pc. It should show various flash devices connected to your computer and those devices may continuosly connect and disconnect. If not it'll show QHUSUB_BULK install the driver using device manager.
7) On Mi flash tool, some device name should show on the devices list if not click refresh and try reconnecting the device. Note: If you dont have proper drivers installed on your pc, this procedure won't work.
8) Finally click on flash and flashing will start. It'll take some time. Once done it'll show operation completed successfully.
9) Finally boot your device using power key.
Brick has received QHSUSB_BULK simple. This is the normal and regular encounter. Hardbrick, you must check point.
2ConHeo said:
Brick has received QHSUSB_BULK simple. This is the normal and regular encounter. Hardbrick, you must check point.
Click to expand...
Click to collapse
who said so?
tested and working
that normal check point is a pain in ass to execute in the first place
Thanks a ton.....It helped a lot
thank u...
thank
How do I put the phone into fastboot mode if it is hard bricked? It won't turn on, I get no responce from phone. When I use method connecting test point to metal cover on mother board of phone usb connects to PC and MiFlash recognizes phone. Try to flash though and I get an error message. No matter what ROM I use, zipped, unzipped or tgz file. Can my phone be unbricked? What am I doing wrong? I have a Mi Max 64GB and am using HELIUM Roms. Please help. Error message is:
The filename, directory name, or volume label is incorrect.(0x8007007b: Open programmer "MPRG*.hex").
I have no clue. Not my first time flashing ROMs or unbricking a phone. It is my first time on a Xiaomi. Only done blackberry and samsung before.
hammer77 said:
How do I put the phone into fastboot mode if it is hard bricked? It won't turn on, I get no responce from phone. When I use method connecting test point to metal cover on mother board of phone usb connects to PC and MiFlash recognizes phone. Try to flash though and I get an error message. No matter what ROM I use, zipped, unzipped or tgz file. Can my phone be unbricked? What am I doing wrong? I have a Mi Max 64GB and am using HELIUM Roms. Please help. Error message is:
The filename, directory name, or volume label is incorrect.(0x8007007b: Open programmer "MPRG*.hex").
I have no clue. Not my first time flashing ROMs or unbricking a phone. It is my first time on a Xiaomi. Only done blackberry and samsung before.
Click to expand...
Click to collapse
did you solve the problem ?
Rajdip said:
Recently while flashing alpha version of MIUI marshmallow on my Mi 4w, my phone got completely bricked. Complete brick in the sense, it won't turn on, neither charge nor show any led indication. This guide should work on other phones also.Let's start:-
1) Although it seems like your phone wont turn on, your phone is actually working, it's just it wont show anything on the screen(no display).
Make sure your phone is charged properly(it will charge even if the led doesn't show any indication).
2) Download and install Mi flash tool and then Fastboot file of your device. http://en.miui.com/a-234.html
3) Unzip the fastboot image, a folder containing flash all.bat should appear if not, extract the extracted file again. Winrar should work fine.
4) Now open Mi flash tool(as administrator) and select the fastboot folder from Mi flash using browse option and also select the proper fastboot script according to need.
Note: Flash_all.bat will completely erase your internal storage.
5) Now press volume down(-) and power key to enter into fastboot. Note: it won't show any visual whatsoever but it'll work.
6) Connect your phone to your pc. It should show various flash devices connected to your computer and those devices may continuosly connect and disconnect. If not it'll show QHUSUB_BULK install the driver using device manager.
7) On Mi flash tool, some device name should show on the devices list if not click refresh and try reconnecting the device. Note: If you dont have proper drivers installed on your pc, this procedure won't work.
8) Finally click on flash and flashing will start. It'll take some time. Once done it'll show operation completed successfully.
9) Finally boot your device using power key.
Click to expand...
Click to collapse
Link not working.
Using another mi flash tool also get nothing. How do I know I get into fastboot?
Already pressed volume down and power button but nothing happened. And checking fastboot devices nothing comes up. Also in mi flash tool nothing.
Hi all as the title suggests is there anyone who has a fairly detailed Unbricking guide or a way to reflash the stock meizu software via fastboot, QFIL or anything that has worked.
The current problem I face is I have the m6 note with Chinese firmware and wanted to flash global firmware via flash fire as the TWRP APK didn't work for me . I can't enter recovery and fastboot gives me a failed message (remote: partition flashing is not allowed ).
Thank you in advance
its for m3 but you may try http forum flymeos com/forum.php?mod=viewthread&tid=35810&highlight=unbrick
also this one for our phone http://forum flymeos.com/thread-38489-1-1.html
This one is from original flyme os forum FAQ
Q: Recover soft-Bricked device (for those can't access the system)
A: Access the Recovery mode:
1.Turn Off the Phone (ensure that you have more than 20% battery)
2.Press and Hold Volume UP + Power
3.release as soon as you see the Meizu logo
Download firmware from http://www.flymeos.com/firmware.html, Copy the update.zip (naming is important) on your phone and select System Upgrade + Clear Data. As soon as it's connected a "Recovery Drive" will pop up. Now, connect your phone (still in Recovery Mode) to your Windows PC. As soon as you are there, you are just fine.
hi thanks @consumimur , but the first method is for mediatek devices isn't it? The second method doesn't work for me at all because i can't enter my recovery , i need some sort of flashing too QFIL doesn't work for well at the the one i tried (2.0.0.5) as it ask for "Rawprogram.xml" and "patch* " which is not in the update.zip
Yusuf.T said:
hi thanks @consumimur , but the first method is for mediatek devices isn't it? The second method doesn't work for me at all because i can't enter my recovery , i need some sort of flashing too QFIL doesn't work for well at the the one i tried (2.0.0.5) as it ask for "Rawprogram.xml" and "patch* " which is not in the update.zip
Click to expand...
Click to collapse
http://4pda.ru/forum/index.php?showtopic=843179&view=findpost&p=69341915
New https://www.movilesdualsim.com...oros/meizu-m6-note-sd625.1222/
Enviado desde mi M6 Note mediante Tapatalk
i think thats what you are looking for
https://firmwarefile.com/meizu-m6-note-m1721
Folks, today I've had the fortune to brick (corrupting the devinfo partition, screwing up recovery and OS boot as well) and unbrick (stock recovery and OS restored and working perfectly) my Meizu M6 Note without opening it up. If anyone is still interested, instructions are here:
https://forum.xda-developers.com/showpost.php?p=77964079
Hi, I have a problem with my m6 note. I have WIFI MAC address between 2: 00: 00: 00: 00: 00 and I can not turn on wifi. I found a solution to upload persist.img and this should help. However, I can not find the persist.img file anywhere. Can you help?
consumimur said:
This one is from original flyme os forum FAQ
Q: Recover soft-Bricked device (for those can't access the system)
A: Access the Recovery mode:
1.Turn Off the Phone (ensure that you have more than 20% battery)
2.Press and Hold Volume UP + Power
3.release as soon as you see the Meizu logo
Download firmware from http://www.flymeos.com/firmware.html, Copy the update.zip (naming is important) on your phone and select System Upgrade + Clear Data. As soon as it's connected a "Recovery Drive" will pop up. Now, connect your phone (still in Recovery Mode) to your Windows PC. As soon as you are there, you are just fine.
Click to expand...
Click to collapse
thank you so much for this @consumimur. It saved me from going down a rabbit hole, after getting a bootloop with meizu x8 m852h, having followed these instructions:
Meizu X8 - Обсуждение - 4PDA
Meizu X8 - Обсуждение, Смартфон, 6.2"
4pda.to
OP:
ttps://4pda.to/forum/index.php?showtopic=965227
author: 555frost555
Download (litter, files lost) archive and unpack to the root of the C drive
Charge your phone at least 50%
Disable signature verification using the following instructions:
For WINDOWS 7-8: Run Command Prompt as administrator, execute two commands in turn and reboot
Code:
bcdedit.exe -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit.exe -set TESTSIGNING ON
For WINDOWS 10: press start, hold shift, press shutdown computer. The computer will boot into a recovery screen. Select custom boot options and disable driver signature verification.
PS personally, I recommend installing on win7 or 8.1 - less haemorrhoids
Install QFIL
Install Qualcomm 9008 driver
Install standard drivers from the phone (connect to the computer in the CD-drive mode and install from there)
Run QFIL and select "flat build"
Select programmer: "prog_firehose_ddr.elf"
Select XML: "rawprogram0.xml"
Select XML: "patch0.xml"
Turn off the phone
Clamp VolUp + VolDn + Power
The Meizu icon appears, followed by a black screen. The keys can be released.
Connect your phone to your computer. It should be detected as Qualcomm 9008.
Press DOWNLOAD
QFIL is very moody about the system and drivers. If you did everything correctly, but you get an error while flashing, then you need to try it on another computer. Preferably on where windows was recently installed ...
When FINISH is written in QFIL, you can turn off the phone and restart it by holding down the power key until it vibrates.
For WINDOWS 7-8: Run Command Prompt as Administrator, execute two commands in turn and reboot
Code:
bcdedit.exe -set loadoptions ENABLE_INTEGRITY_CHECKS
bcdedit.exe -set TESTSIGNING OFF
I did this with the QFIL archive linked in https://4pda.to/forum/index.php?act=findpost&pid=88712568&anchor=Spoil-88712568-6
and received a bootloop on meizu x8 m852h. Then I did what @consumimur wrote
I did this on a windows 10 machine
I did this on a w10 machine
This is unbrick firmware. Enjoy free. Download Unbrick Meizu M6 firmware.
Hi everybody , today I will share very easy way to unbrick your Lenovo Vibe Shot Z90a40 device .
In my case this device was bricked while instaling custom twrp recovery and custom android 7 OS I got device in that state so the problem was that you are unable to flash your device in diagnostic 9006 mode with to many read only partitions , which I was unable to format or delete in read only state , but actually the problems was not it those partition at all, is about to get
HS-USB QDLoader 9008 mode so you can flash stock firmware on it .
Preparing Steps to do before we start :
1. Disable or remove your Antivirus (because sometimes antivirus can block instaling drivers , ports or running flash tool)
2. Uninstall all the previous drivers you used for flashing or unbrick use free tool called USBDeview
for 32 bit users:
https://www.nirsoft.net/utils/usbdeview.zip
for 64 bit users:
https://www.nirsoft.net/utils/usbdeview-x64.zip
3. Put your windows in Test mode
To put your Windows in test mode just Run As Administrator Command Prompt and insert one of the following command:
bcdedit -set testsigning on ( to enable test mode)
bcdedit -set testsigning off ( to disable test mode)
Or Disable driver signature
for Windows 7
https://www.youtube.com/watch?v=6gYhHD622AA
for Windows 10 users:
https://www.youtube.com/watch?v=71YAIw7_-kg
After that reboot your PC .
4. Uninstall all flash program from your pc like MiFlash , QPST , Qloader ...
Use Revo Uninstaller for advanced uninstaling that clean leftover files and registry which is stored inside your Windows registry.
https://www.revouninstaller.com/revo_uninstaller_free_download.html
After that reboot your PC .
5. Install Microsoft .NET Framework 4 download from here: (if you already have instaled skip this)
https://www.microsoft.com/en-us/download/details.aspx?id=17851
6. Install first right Qualcomn driver download from here :
https://drive.google.com/file/d/0B1Sms71Oe6FIdUE4em9DNjV3Y00/view
Credits for driver : https://www.youtube.com/channel/UC8LoQb68tjBYxwN97b4pvtA
7. Install Lenovo USB driver download from here :
https://lenovousbdriver.com/tutorial/install-lenovo-usb-driver
8. Install Qpst (Qfil flash tool) download from here:
https://drive.google.com/file/d/0B1Sms71Oe6FIVTRwbWpSdEZfM2c/view
9. Install Minimal ADB & Fastboot 1.4.2 command tool download from here
(while you start installing tool check to be in desktop is easy )
https://androidfilehost.com/?fid=745425885120698566
in order to install run ADB & Fastboot 1.4.2.exe with Administrator and just write y and hit enter for all .
10. Download twrp recovery for fastboot flashing and extract to Desktop, download from here :
http://lenovo-forums.ru/applications/core/interface/file/attachment.php?id=56391
11. Download stock firmware for QPST Flashing ( inside is drivers and tools also but don't use that one's ) download from here :
https://cloud.mail.ru/public/HCn4/auVy8DVo1
Also extract stock recovery for later one inside adb folder
12. Very important is to use Original usb cable ! otherwise your device won't be recognized property!
13. Make sure your battery is charged if you are not sure put in charger for about 2 hours in charger on in pc!
If your device immediately show up Lenovo logo just hold Vol - and power button together release power button once is rebooting put keep holding Vol - it should be black screen now with white indicator while is charging if not , repeat this proces without charger. This is secure because if you let your phone to be charged with Lenovo logo device will be hot and probably the lcd will hot burning effect !!!
So Let's start
1. Make sure your device is OFF first !
2. Hold Vol + and Vol - buttons together in order to enter into FastBoot mode and hold it like that plug usb and see if windows is detecting your device then release buttons.
3. Now once the drivers are successfully installed run Minimal ADB & Fastboot tool .
4. Write command :
fastboot device and press Enter
(you should see your device available )
5. Now write :
fastboot flash recovery (drag inside command tool with mouse "recovery.img" extracted from stock recovery from preparing steps on 11.) and press Enter
6. Next write each command one by one :
fastboot erase cache and press Enter
fastboot erase system and press Enter
7. Now unplug your device from PC.
8. Enter to Lenovo stock recovery by holding 3 buttons :
Vol + & Vol - & Power button at the same time , release just power button once your device vibrate .
Once you see Lenovo MAIN MENU screen press on ''wipeuser data" and wipe each one ,
one by one :
fuse wipe data ( press on YES )
fuse format data ( press on YES )
wipe cache ( press on YES )
Now there is two method for fix :
#First method - Flashing ota firmware from stock recovery
This method is from forum.lenovo.com which doesn't work for me is fail at 49% probably because S208 is old version which is maybe not allowed because I flashed recovery from S363 firmware I don't know but you can try .
1. You need 4 gb or more micro SD card , also make sure is formatted with Fat 32 .
2. Download Z90a40_USR_S208_1507141216_Q2020131.4_ROW_OTAFull.zip, rename it to "update.zip"
https://drive.google.com/file/d/0B8CarqWdS9gZZmJmVGp6NkFWRlk/view
3. Copy it to micro SD card again 4 GB or more !
4. Go into recovery menu:
- turn off the phone
- hold both vol+ and vol- buttons
- power on phone, keep both vol+ and vol- keys pressed until it enters recovery
5. From recovery menu choose install update package
After that go back and press on "poweroff"
#Second method - Flashing stock firmware with Qfil
1. Hold Vol + & Vol - buttons and plug usb cable to enter into fastboot mode and open Minimal ADB & Fastboot to again .
2. Now to put your device in EDL mode and open HS-USB QDLoader 9008 for flashing write this command:
fastboot reboot edl and press Enter
Now you should see that your device is detected like "HS-USB QDLoader 9008" so wait for instalation of that driver.
If you are unable to reboot into EDL mode , flash twrp.img from "twrp/img" folder .
In order to flash twrp recovery probably you need to unlock bootloader , but try first without unlocking if is not flashing then unlock bootloader , if is flashing without unlocked bootloader skip this!
https://www.cyanogenmods.org/forums/topic/unlock-bootloader-android-phone-using-fastboot/
To do that just write :
fastboot flash recovery (drag inside command tool with mouse "twrp.img" from " twrp/img" folder ) and press Enter
3. Once is installed go to QPST directory in my case "C:\QPST\bin" and Run as Administrator "QFIL.exe."
.
Rest you have here here explained ...
https://www.gsmhelpful.com/2017/07/how-to-flash-lenovo-vibe-shot-z90a40-with-qfil-flash-tool.html
If for some reasons flashing is fail , plug usb in another usb port USB 2.0 (recommended) and repeat process.
DOWNGRADE from Marshmallow 6.0.1 to Lolipop 5.1
For those one's who want to downgrade device back to Lolipop try this at your own risk !!!
https://forums.lenovo.com/t5/K-and-...-downgrade-to-lollipop-5-1-GUIDE/td-p/3527835
Good luck and God bless you all
The files uploaded on tinyupload can't be downloaded, Lenovo USB driver and unbrick stock recovery & twrp recovery, the link expired.
Could you please upload them again?
Thank you!
Links is updated . Thank you for let me know ...
so I can connect my bricked phone to a Windows PC by shorting the test points. But the device (Qualcomm HS-USB QLoader xxx) also keeps on disappearing in Device Manager. In most cases, the device only shows up in Device Manager for 1 second and disappears immediately.
Any ideas on how to fix?
Thanks
edit1: tried on a laptop running Windows 10 and another laptop running Windows 7.
edti2: My phone is stuck in a bootloop. I cannot even get it to boot into fastboot mode.
mrjayviper said:
so I can connect my bricked phone to a Windows PC by shorting the test points. But the device (Qualcomm HS-USB QLoader xxx) also keeps on disappearing in Device Manager. In most cases, the device only shows up in Device Manager for 1 second and disappears immediately.
Any ideas on how to fix?
Thanks
Click to expand...
Click to collapse
Steps:
A).On the computer in windows disable driver signature enforcement featrure and turn off any protection like security suites,AV software or firewalls.To disable driver signature enforcement you must open command prompt and type:a)bcdedit.exe -set loadoptions ENABLE_INTEGRITY_CHECKS and press enter
b)bcdedit.exe -set TESTSIGNING ON and press enter
c)reboot computer
d) install MI flash after reboot;download it from here :http://en.miui.com/thread-235865-1-1.html
B) On the phone:
1.Hold Vol - and Vol + and plug Usb cable in computer&phone
2.download ADB files from here http://en.miui.com/thread-235865-1-1.html
3.extract files from archive to folder
4. in this folder,where you have extracted adb files press:shift on keyboard and right click on the mouse in the same time and choose "open command window here"
5.in command window type:a)adb devices and press enter
b)adb reboot edl and press enter
Now you are in download mode
6.from device manager install qualcomm driver;it should be seen in other devices section;right click---update driver----navigate to :C/Program files(X86)/XIaomi/Mi flash/Qualcomm/Driver;Note:you need x64 windows computer for this operation
7.start MI flash---right click and run as administrator;browse for rom folder,you need a fastboot rom(the rom need with suffix tgz to be;not zip).Put the tgz archive(rom) in Local Disk C and extract with winrar!!!!!!(use winrar) to folder;rename the created folder to ROM.In MI flash when do browse for folder SELECT ENTIRE FOLDER NOT JUST THE FOLDER IMAGES.OK?
8.in MI Flash window press refresh button from up side;the device should appear on the list
9.in MI Flash windows in the down side of windows tick the litlle circle who say:Flash all
10.Press flash button from up
1.1. Wait until it finish flashing procedure:should appear in the right side from device peration completed succesfully
12.Remove usb cable and press power button on the device;keep the power button pressed until the device give you a vibration,the release it
ketan7731 said:
Steps: snip
Click to expand...
Click to collapse
My phone is stuck in a bootloop. I cannot even get it to boot into fastboot mode.
deleted
I have the same problem but mine is Red mi Note 9 Merlin SOC: MT 6768 what do i need to do, Phone cant go fast boot mode nor recovery but just boot re loop. My Mi account credentials are active and the phone boot lock is unlocked.The problem i have is the connection in the device manager comes and goes,May someone give the detailed info on how i my revive the phone
Hi,
I have encountered a suddenly dead old device. It was working long time without an issue, but one day it does not start and just a logo is displayed. It was possible to turn off the device or enter the recovery menu. I have found more posts about repairing with some unofficial flash tools or using unofficial ROMs.
I was able to revive the device finally with success and using official tools only, so I would like to share the steps I have used, basically it is about downloading the official ROM from Acer site and flashing it with ADB:
1. You will need Windows computer, I was not able to make the Mac recognise the phone properly, but maybe it is somehow possible.
2. Download official Android 4.4.2 ROM from ACER site: https://www.acer.com/ac/en/GB/content/drivers
enter SNID (check the phone under cover), look in OS category and download, the ZIP file is ~700MB large, do not unzip.
Download also the Drivers and extract it.
No need to download unofficial ROMs or drivers for this phone I think.
3. Download android platform tools from https://developer.android.com/studio/releases/platform-tools and unpack to some directory
4. Install phone Drivers manually from Device manager, use Action/Add device command and navigate to INF in the driver folder.
5. Turn on the phone and star recovery mode (Vol down+Power).
6. Connect the charged device with USB cable.
7. Start cmd.exe and navigate to platform-tools directory, start "adb devices" command, your device should be listed.
If no device is listed, return to driver installation step.
8. start "adb reboot bootloader", phone will reboot, hint about flashing the ROM appears
9. start "adb sideload yourpathto/officialROM.zip
10. wait few minutes until the installation is finished, phone reboots and should work.
11. you are happy
Hey,
2 Years ago my E700 dropped down, since then it does not work anymore. It shows no reaction if i want to start the device.
Could something be broken?
Do you have an idea to fix it?