Related
Rite,
İ am new to ROMs and everything. İ downloaded FOXHOUND Sniper Wolf ROM. İ followed the instructions which are:
1. Boot into recovery mode
2. Format System / Factory Data Wipe
3. Wipe cache and also wipe dalvik cache
4. Install the zip file and you will get the CWM install completed message.
5. Select Reboot Now and let the phone boot up to an Android setup screen.
6. Setup the phone as requested
7. Reboot the phone into recovery mode again and wipe cache and dalvik cache again
8. Reboot phone and everything should be working...
On stage 5. my phone loads up to the android setup screen but a message comes up saying:
'Select and application for the USB device' and below that it says 'no application can perform this action' and another message below that ' %1$s is not responding. would you like to close it'.
İf İ try to do anything the phone just reboots and the same process keeps repeating. İ have searched but cannot find anything relating to this problem. Please help me....
reflash the ROM,
not helped, download the rom again and flash
still not helped select someother ROM
ZACQ8 said:
reflash the ROM,
not helped, download the rom again and flash
still not helped select someother ROM
Click to expand...
Click to collapse
Thank you for your reply but can you be a little bit more specific as İ am a newbie, İ really appreciate the help...
So i re installed the ROM but still have the same problem...
The phone does not boot for me to download another ROM.
Any other solutions?
save your important data from sd card(internal card) , copy to computer , make a hard reset(erase all internal data) flash a new rom via odin , root with cf-root via odin(i recomand xila 2 witch cf-root that u find here on xda,and xila2 room too, and then download the rom you wanted put it on your sd card,go to recovery wipe cache dalvik,wipe data factory reset,install the rom u want. after u may pasye the data you saved before on computer. good luck. for example u can save all your data witch titanium backup.
Download again the rom
Make a full wipe, factory reset,
Reinstall the rom
If that doesn't work
Install via Odin a CF root rom, and use other rom, like cm9
Sent from SGSII//CM9 >>xBlackDroid<<
enigmatyq said:
save your important data from sd card(internal card) , copy to computer , make a hard reset(erase all internal data) flash a new rom via odin , root with cf-root via odin(i recomand xila 2 witch cf-root that u find here on xda,and xila2 room too, and then download the rom you wanted put it on your sd card,go to recovery wipe cache dalvik,wipe data factory reset,install the rom u want. after u may pasye the data you saved before on computer. good luck. for example u can save all your data witch titanium backup.
Click to expand...
Click to collapse
if you dont want to make that steps you may do this : go to recovery, mounts&storage, format cache , format data , format system , them reflash your rom from recovery , after this wipe cache wipe dalvik wipe data , and the fix permissions.
Rite, so İ can recover my phone by loading another ROM via ODİN?
Sorry to be a pain, but İ am a dummy when it comes to this stuff...
muzzyx said:
Rite, so İ can recover my phone by loading another ROM via ODİN?
Sorry to be a pain, but İ am a dummy when it comes to this stuff...
Click to expand...
Click to collapse
yes you can.
don.t panic,that.s the reason for xda exist,to help pples.
muzzyx said:
Rite, so İ can recover my phone by loading another ROM via ODİN?
Sorry to be a pain, but İ am a dummy when it comes to this stuff...
Click to expand...
Click to collapse
Yeah man, download some from general section
Sent from SGSII//CM9 >>xBlackDroid<<
enigmatyq said:
yes you can.
don.t panic,that.s the reason for xda exist,to help pples.
Click to expand...
Click to collapse
Thank you
ok, so how can İ download the ROM again and install all over if my phone is not booting?
muzzyx said:
Thank you
ok, so how can İ download the ROM again and install all over if my phone is not booting?
Click to expand...
Click to collapse
well do what i say in the first post,install that rom via odin,root,and after download the rom u want in your phone and flash it.
flash this http://hotfile.com/dl/146503450/02dbdd0/I9100XILA2_I9100OXIKK1_ITV.zip.html then flash this http://download.chainfire.eu/137/CF-Root/SGS2/CF-Root-SGS2_XI_ITV_LA2-v5.0-CWM5.zip and then install the rom u want...remember to do a hard reset..and all i posted in first post.
just found this thread http://forum.xda-developers.com/showthread.php?t=1449771
İs it ok if İ follow the instructions?
Hello
Im bored by using android 4.2 from many years, i want something new in my device
im tired of finding how to install cyanogen in lenovo A680
i dont know from where i can get working stock ROM of Lenovo A680
and i dont know how can i port rom perfectly
i hope you can help me !
Hi
For install ROM anywere(cyanogen/MIU/Stock):
Put the firmware(ROM.zip) archive to SD-card,
Switch off your phone
get into recovery (You need to CWM: forum.xda-developers. com/android/general/rooting-twrp-cwm-lenovo-a680-row-t3036490 ):
- Go to the backup and restore, create a backup of the current state of your machine,
- Wipe Data / Factory Reset -> delete all user data
- Wipe Cache Partition -> Wipe cache
- Advanced -> Wipe Dalvik Cache -> Wipe Dalvik Cache
Next Install zip from sdcard -> choose zip from sdcard -> Select the firmware and install and reboot.
OR: Install Stock Rom and put ROOT for unistall apps system, and install Theme/Xposed Modules.
maxnuk said:
For install ROM anywere(cyanogen/MIU/Stock):
Put the firmware(ROM.zip) archive to SD-card,
Switch off your phone
get into recovery (You need to CWM: forum.xda-developers. com/android/general/rooting-twrp-cwm-lenovo-a680-row-t3036490 ):
- Go to the backup and restore, create a backup of the current state of your machine,
- Wipe Data / Factory Reset -> delete all user data
- Wipe Cache Partition -> Wipe cache
- Advanced -> Wipe Dalvik Cache -> Wipe Dalvik Cache
Next Install zip from sdcard -> choose zip from sdcard -> Select the firmware and install and reboot.
OR: Install Stock Rom and put ROOT for unistall apps system, and install Theme/Xposed Modules.
Click to expand...
Click to collapse
Thanks for those step by step answer.!
sure i will follow your step when i will install ROM
oh well, can you tell me from where i can get Cyanogen for Lenovo A680 ?
Do you test: youtu.be/RyVakGPT11I
but I'm not sure...(Backup!)
maxnuk said:
Do you test: youtu.be/RyVakGPT11I
but I'm not sure...(Backup!)
Click to expand...
Click to collapse
Thanks for your help
but according to comments, it seems fake rom ,full of bugs! better I Should not try
hey can you tell me how can I port rom and make it compatible with my device?
I'm interested into cyanogen ,I already downloaded both cyanogen 12.1 and 13
I want to make it compatible with my device
I'll be thankful to you
Port rom... you have very bugs. But, to port rom: https://wiki.cyanogenmod.org/w/Doc:_porting_intro
Ideally you get a ready-rom, like the settings of your device and change.
maxnuk said:
Port rom... you have very bugs. But, to port rom: https://wiki.cyanogenmod.org/w/Doc:_porting_intro
Click to expand...
Click to collapse
I'm Sorry if I bother you
wow your answer is Really so awesome
im going to read all the contents!
Thanks Really!
Your specs: Chipset:Mediatek MT6582 // GPU: Mali-400MP2 // 4 GB Rom, 1 GB RAM.
Try: http://www.mtkroms.com/2016/02/marshmallow-cyanogenmod-13-for-mt6582.html
maxnuk said:
Your specs: Chipset:Mediatek MT6582 // GPU: Mali-400MP2 // 4 GB Rom, 1 GB RAM.
Try: http://www.mtkroms.com/2016/02/marshmallow-cyanogenmod-13-for-mt6582.html
Click to expand...
Click to collapse
you are the boss!
Really your answer is interesting
soon I'll be downloading it
but I afraid little bit, Because just 2 day ago I tried to flash custom rom and it stuck at booting logo
I was unable to boot into recovery too
then I give it to service center, and then my device working today
XD You need not have gone ... Boot loop, that always happens..
maxnuk said:
XD You need not have gone ... Boot loop, that always happens..
Click to expand...
Click to collapse
Haha Thanks dude...hey do you know how can I flash custom rom in computer? using emulators?
so that I can test whether rom is working Fine or not, so that I can avoid risk on my device
Do you have skype ?
maxnuk said:
Do you have skype ?
Click to expand...
Click to collapse
yes I've
Do you use Smart Phone Flash tool ?
maxnuk said:
Do you use Smart Phone Flash tool ?
Click to expand...
Click to collapse
I know how to use it, but I didn't used,Because last time I tried to flash rom using TWRP
you know What was Good wrong?
I did wipe cache and data, after that, I tried to install custom rom zip, and I found it's corrupted!
so, I ended up with bricking my device
that's why I want to flash rom in computer first!! Haha
when you bricked your phone, you could not get into TWRP ?
maxnuk said:
when you bricked your phone, you could not get into TWRP ?
Click to expand...
Click to collapse
yes right!! and even I was unable to get into recovery mode using key combination
just use that Smart Phone Flash tool..
maxnuk said:
just use that Smart Phone Flash tool..
Click to expand...
Click to collapse
Oh Thanks for that.. sure I'll use it next time...but still I afraid of bricking! do you have any idea how can I flash custom rom in computer emulator? so I can make sure rom is working Fine or not
I do not know. I recommend you not flash rom.
Ok , Im running CM 13 i9300 and it worked so well except the camera. I always got the error "Can't connect to camera" . So I was trying to fix that problem and I found couple of solution . The solution need an app that requires SuperSU permission . And It was kinda weird because there's no "permission asking" popup from SuperSU. So I open SuperSU and it told me to update SuperSU binary file. So I tried to update it and it failed. So I tried to update it manually but I found other thing which is to flash the latest version of SuperSU direct from chainfire website. I deleted the old SuperSU (The one that needs to be updated) and I flashed the new SuperSU zip and wipe dalvik cache through my TWRP Recovery and then I reboot my phone . And got stuck at the Cyanogenmod Logo . So what should I do to get my phone back to normal ? I mean back to CM13 and everything I have before. PLS HELP
Note : actually , after I flashed CM 13 . I dont have the SuperSU in my apps . So I manually downloaded it from the playstore . It's weird because it should automatically be there .
Isn't root access found under developer settings?
audit13 said:
Isn't root access found under developer settings?
Click to expand...
Click to collapse
I seriously dunno about the root access at the developer settings . Now my phone is soft bricked and I'm gonna lose all of my data. Any clue on how to reflash the CM13 without deleting my stuff?(factory reset)
p/s : Yes , It's in the Developer settings
Boot into TWRP and reflash the same version of CM that was on the phone before it soft-bricked.
audit13 said:
Boot into TWRP and reflash the same version of CM that was on the phone before it soft-bricked.
Click to expand...
Click to collapse
Should I clear data , wipe cache and dalvik , factory reset all that or just go to TWRP and just flash
You could just flash over the existing ROM without wiping. If it doesn't boot, wipe cache. If it still doesn't boot, wipe data and cache.
audit13 said:
You could just flash over the existing ROM without wiping. If it doesn't boot, wipe cache. If it still doesn't boot, wipe data and cache.
Click to expand...
Click to collapse
Ok sir , new problem .. So I uses CM13 Nightlies , And I dont remember which version. Can I use latest version of CM13 Nightlies?
Yes, try the latest nightly.
audit13 said:
Yes, try the latest nightly.
Click to expand...
Click to collapse
Man It worked , seriously thank you man :good: :good: :good:
Glad to hear you solved the problem. We're all here to help and learn from each other.
So after I flashing Lineage os , it was working fine and until recently , so I was out without my phone and then when I got home I try to open my phone(power on) but didn't open . So I go and charge the phone and it was going well like the battery logo is there and everything is like normal . And then I go play some games , when I checked my phone again , it is at Lineage os boot logo and it is very very hot too . So I force shutdown it . And then take the batteries out to cooldown my phone , after that I try to start it again , but no use . So I went to recovery mode and wiped cache and dalvik cache using TWRP , but no use also , my phone still stuck at the boot logo .
I am very sorry for my bad english
Please help
You need to flash back to stock firmware and start over again. Something is corrupt.
Beamed in by telepathy.
shivadow said:
You need to flash back to stock firmware and start over again. Something is corrupt.
Beamed in by telepathy.
Click to expand...
Click to collapse
Can I transfer Lineage os and gapps to the phone without the phone being on ? Is there a way to transfer files to phone other that ADB SIDELOAD . And If I managed to transfer the files , can I flash the rom without losing the data ? Like the picture etc . Not the application .
Pixelzack said:
So after I flashing Lineage os , it was working fine and until recently , so I was out without my phone and then when I got home I try to open my phone(power on) but didn't open . So I go and charge the phone and it was going well like the battery logo is there and everything is like normal . And then I go play some games , when I checked my phone again , it is at Lineage os boot logo and it is very very hot too . So I force shutdown it . And then take the batteries out to cooldown my phone , after that I try to start it again , but no use . So I went to recovery mode and wiped cache and dalvik cache using TWRP , but no use also , my phone still stuck at the boot logo .
I am very sorry for my bad english
Please help
Click to expand...
Click to collapse
Try going to recovery and dirty flash the rom then wipe cache and dalvik then reboot.
By dirty flashing, i mean no wipes, just flash it over the existing one then wipe cache and dalvik then reboot.
MigoMujahid said:
Try going to recovery and dirty flash the rom then wipe cache and dalvik then reboot.
By dirty flashing, i mean no wipes, just flash it over the existing one then wipe cache and dalvik then reboot.
Click to expand...
Click to collapse
So , I tried to transfer rom and gapps to my phone through recovery , so when I mount storage , the device shown in my pc so I started transfer the files , when it reached around 39% , the device is missing . So I unmount the storage at TWRP and re-mount it . But no use , the device is not detected . What should I do?
Pixelzack said:
So , I tried to transfer rom and gapps to my phone through recovery , so when I mount storage , the device shown in my pc so I started transfer the files , when it reached around 39% , the device is missing . So I unmount the storage at TWRP and re-mount it . But no use , the device is not detected . What should I do?
Click to expand...
Click to collapse
Try using a different cable and a different USB port.
And check if MTP is enabled in "mount" through the button in the down right corner, it should say "disable MTP".
MigoMujahid said:
Try using a different cable and a different USB port.
And check if MTP is enabled in "mount" through the button in the down right corner, it should say "disable MTP".
Click to expand...
Click to collapse
Its a success ! although dirty flashing didn't work but I managed to transfer the files and flashed it . Thank you so much sir! :fingers-crossed: :fingers-crossed: :good: :good: :good:
MigoMujahid said:
Try using a different cable and a different USB port.
And check if MTP is enabled in "mount" through the button in the down right corner, it should say "disable MTP".
Click to expand...
Click to collapse
Hi sir , the problem came back , but this time , I noticed "Failed to mount /efs . Invalid Argument" when factory reset through TWRP . I was going to factory reset and then flash rom and Gapps but what should I do with the /efs ?
Pixelzack said:
Hi sir , the problem came back , but this time , I noticed "Failed to mount /efs . Invalid Argument" when factory reset through TWRP . I was going to factory reset and then flash rom and Gapps but what should I do with the /efs ?
Click to expand...
Click to collapse
OK, try flashing your Stock ROM with Odin first.
and see if everything goes right.
then you will have to re-flash the TWRP and try again.
Pixelzack said:
Hi sir , the problem came back , but this time , I noticed "Failed to mount /efs . Invalid Argument" when factory reset through TWRP . I was going to factory reset and then flash rom and Gapps but what should I do with the /efs ?
Click to expand...
Click to collapse
Make sure your imei still exists. If not then you need to fix the efs partition before you can proceed. Factory reset should always be done via the device software, NEVER TWRP!. TWRP has a habit of killing phones.
Beamed in by telepathy.
shivadow said:
Make sure your imei still exists. If not then you need to fix the efs partition before you can proceed. Factory reset should always be done via the device software, NEVER TWRP!. TWRP has a habit of killing phones.
Beamed in by telepathy.
Click to expand...
Click to collapse
if TWRP kills phones, then it wouldn't have been the most famous and the most used custom recovery in the android world.
he can do factory reset from there as long as he isn't using stock ROM, and even if he uses stock ROM, it does no harm, but it's more preferable that he uses stock recovery for that.
MigoMujahid said:
if TWRP kills phones, then it wouldn't have been the most famous and the most used custom recovery in the android world.
he can do factory reset from there as long as he isn't using stock ROM, and even if he uses stock ROM, it does no harm, but it's more preferable that he uses stock recovery for that.
Click to expand...
Click to collapse
Twrp has caused more mount issues than you've had hot dinners. The reason twrp is the 'most famous' recovery is because it's the only current recovery, Cwm is defunct. Cwm didn't cause mount issues, it only came about with twrp, on ALL devices.
I have also fixed the mount issue with twrp by changing recovery to an old official cwm and no problems since. Do not trust TWRP, you have been warned!.
Beamed in by telepathy.
MigoMujahid said:
OK, try flashing your Stock ROM with Odin first.
and see if everything goes right.
then you will have to re-flash the TWRP and try again.
Click to expand...
Click to collapse
I wiped and reflash the rom and Gapps , when I look at backup in TWRP , the EFS is 0mb , so I restored the EFS and rebooted the phone . It worked well . Thank you again ~!
shivadow said:
Make sure your imei still exists. If not then you need to fix the efs partition before you can proceed. Factory reset should always be done via the device software, NEVER TWRP!. TWRP has a habit of killing phones.
Beamed in by telepathy.
Click to expand...
Click to collapse
I was lucky that I made a backup of the EFS . After I restored the efs , the phone rebooted well . And my IMEI still exist . Thank you so much sir!
Pixelzack said:
I was lucky that I made a backup of the EFS . After I restored the efs , the phone rebooted well . And my IMEI still exist . Thank you so much sir!
Click to expand...
Click to collapse
Very lucky but that is why we stress that it MUST BE done, for times like these.
Beamed in by telepathy.
shivadow said:
Twrp has caused more mount issues than you've had hot dinners. The reason twrp is the 'most famous' recovery is because it's the only current recovery, Cwm is defunct. Cwm didn't cause mount issues, it only came about with twrp, on ALL devices.
I have also fixed the mount issue with twrp by changing recovery to an old official cwm and no problems since. Do not trust TWRP, you have been warned!.
Beamed in by telepathy.
Click to expand...
Click to collapse
I'll keep that in mind..
thanks :good:
Hi,
I know that 7.1.1 ROM comes with encryption enabled by default but can changing rom or reverting back to stock ROM
will disable or remove encryption ?
I wanna know if there is way to disable default encryption on RR rom
To remove encryption, format data and flash one of the following
SuperSU, Magisk, Custom Kernel or FED Patcher
Before booting the rom.
All of above can disable force encryption.
corkiejp said:
To remove encryption, format data and flash one of the following
SuperSU, Magisk, Custom Kernel or FED Patcher
Before booting the rom.
All of above can disable force encryption.
Click to expand...
Click to collapse
By format data do u mean wiping data/media too ? Or just wipe data from twrp
@bHi71 said:
By format data do u mean wiping data/media too ? Or just wipe data from twrp
Click to expand...
Click to collapse
I said to Format Data, wiping data will still leave it encrypted.
corkiejp said:
I said to Format Data, wiping data will still leave it encrypted.
Click to expand...
Click to collapse
Tnx for the help
Reminder: - If you update your rom, flash your chosen method as well at the same time or the device will re-encrypt on boot!
corkiejp said:
Reminder: - If you update your rom, flash your chosen method as well at the same time or the device will re-encrypt on boot!
Click to expand...
Click to collapse
Tnx I'll keep that in mind while updating
@bHi71 said:
Hi,
I know that 7.1.1 ROM comes with encryption enabled by default but can changing rom or reverting back to stock ROM
will disable or remove encryption ?
I wanna know if there is way to disable default encryption on RR rom
Click to expand...
Click to collapse
I m also thinking the same
Help me too man.
I m on a custom rom Android 7.1.2
If I wanna flash miui 9 is there anything that I should keep in mind
I was just thinking to wipe my data nd install rom
Pls correct me if I am NOOB . Nd save my phone from brick ?