I've been using OmniROM and TWRP for quite some time now.
I put the phone on charge and a few minutes later it was stuck on Samsung initial Screen with the usual red triangle. (Showing SAMSUNG Galaxy SIII GT-I9300)
I removed the charger and battery and restarted, it was still stuck on Samsung Boot Screen.
Any ideas how to recover the phone?
I have tried going through some of the other forum threads but most of them can't go to download mode. I can go into TWRP and download mode both. I tried recovering the phone using Kies "Firmware Initialization" but it generates "your phone cannot be upgraded to the latest version" and stops.
falconflyer82 said:
I've been using OmniROM and TWRP for quite some time now.
I put the phone on charge and a few minutes later it was stuck on Samsung initial Screen with the usual red triangle. (Showing SAMSUNG Galaxy SIII GT-I9300)
I removed the charger and battery and restarted, it was still stuck on Samsung Boot Screen.
Any ideas how to recover the phone?
I have tried going through some of the other forum threads but most of them can't go to download mode. I can go into TWRP and download mode both. I tried recovering the phone using Kies "Firmware Initialization" but it generates "your phone cannot be upgraded to the latest version" and stops.
Click to expand...
Click to collapse
Download stock rom from Sammobile and flash in Odin..
tallman43 said:
Download stock rom from Sammobile and flash in Odin..
Click to expand...
Click to collapse
Downloaded latest stock rom ML4 and this is what I get in Odin 3.09:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XWUGML4_I9300ODDGML4_I9300DDUGMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/038> Added!!
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> SingleDownload.
<ID:0/038> sboot.bin
<ID:0/038> NAND Write Start!!
<ID:0/038> FAIL!
<ID:0/038>
<ID:0/038> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
falconflyer82 said:
Downloaded latest stock rom ML4 and this is what I get in Odin 3.09:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XWUGML4_I9300ODDGML4_I9300DDUGMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/038> Added!!
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> SingleDownload.
<ID:0/038> sboot.bin
<ID:0/038> NAND Write Start!!
<ID:0/038> FAIL!
<ID:0/038>
<ID:0/038> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Nand write fail usually means dead emmc chip. You can try rescue firmware here >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << but I think you need to send it fto service for repair.
tallman43 said:
Nand write fail usually means dead emmc chip. You can try rescue firmware here >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << but I think you need to send it fto service for repair.
Click to expand...
Click to collapse
I tried the rescue firmware, similar result:
Code:
<ID:0/014> Odin v.3 engine (ID:14)..
<ID:0/014> File analysis..
<ID:0/014> SetupConnection..
<ID:0/014> Initialzation..
<ID:0/014> Set PIT file..
<ID:0/014> DO NOT TURN OFF TARGET!!
<ID:0/014> FAIL!
<ID:0/014>
<ID:0/014> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I finally took to a repair shop, they say it is my fault since I rooted it (they can see the red exclamation mark), and will charge extra for "software change".
Any idea how to reset the counter in download mode, revert to stock recovery and remove the red exclamation mark in bootloader?
P. S. I read somewhere in case of dead emmc I shouldn't be able to see the device version in download mode. But I can..
bricked device i9300..
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CheckROM_V4_LG8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
it gets stuck for hours without any response ... can any one help please
dupri11 said:
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CheckROM_V4_LG8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
it gets stuck for hours without any response ... can any one help please
Click to expand...
Click to collapse
Did you try Odin 3.09? I too get the same result as you with Odin 3.07. With 3.09 I get the write fail error.
falconflyer82 said:
Did you try Odin 3.09? I too get the same result as you with Odin 3.07. With 3.09 I get the write fail error.
Click to expand...
Click to collapse
I used the 3.09 still same problem am stuked up really
If the rescue firmware and pit didn't flash then your emmc chip is damaged, either new motherboard or phone.
Sent from my GT-I9300 using Tapatalk
falconflyer82 said:
I finally took to a repair shop, they say it is my fault since I rooted it (they can see the red exclamation mark), and will charge extra for "software change".
Any idea how to reset the counter in download mode, revert to stock recovery and remove the red exclamation mark in bootloader?
Click to expand...
Click to collapse
There must be a way to reset the download count by installing stock recovery. Maybe @Chainfire can help here.
Sent from my XT1033 using Tapatalk
dupri11 said:
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CheckROM_V4_LG8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
it gets stuck for hours without any response ... can any one help please
Click to expand...
Click to collapse
what @boomboomer said is what you should consider.
If you keep on insisting, you will just damage the phone more ( i am talking from experience ) .
change motherboard or in some places, people can replace the emmc Chip for you.
Salam
Samsung Galaxy 3 Tmobile edition. d2tmo. I am running cyanogenmod 12.(something) and I cant connect to wifi. I cant seem to flash any non lollipop rom, with both twrp and clockwork mod. So I decided Im going to go back to factory settings. So using odin I downloaded the stock firmware and tried to flash it. Odin gives me this
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVALEM_T999TMBALEM_T999UVALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Click to expand...
Click to collapse
I have not been able to flash anything with odin and I suspect there is something in the phone rolling back and changes odin does. I really would like to get this phone working (current rom works but cant connect to wifi). Ive used guides like this one and I have not had any luck so far.
Hello XDA,
I did brick my phone by trying to downgrade to 5.0.2 from 5.1.1 and bricked my phone and searching this forum I felt that there should be a post like this to ease the journey of people like me. As I did learn a lot from my 5 years android journey, I would like help everybody like me. Therefore if I find any important/"you may not know" fixes, I will share here with headings. Also If you have another solutions for any problems of these kind; please write here so I can collect em' all in the OP. Let's go!
-ODIN fail while flashing hidden.img-
Solution: This is caused because of your partition(pit). In XDA, you can find .pit files of S6 Edge for several models (i.e. I have a g925f so i have to find the corresponding pit file. The one worked for me was the G925F pit with Hidden_300M. First you flash this pit to your phone, then try to flash your rom; you're good to go!
Solution 2 Thanks to @Alex-V : Just delete the hidden.img from the rom.
---------------------------------------------------------------
-If you can't properly enter to recovery mode-
Solution: Please do the combo "Volume Down-Home-Power" until you reach download mode. When you reach there again do the same combo until the screen goes off. When it goes off QUICKLY switch to "Volume Up-Home-Power" combo and hold it until the screen comes in and dims a bit. When it dims release all buttons and ta-da you're in recovery mode.
---------------------------------------------------------------
-ODIN gives a fail at NAND write-
Solution: This problem is caused because of the nand mismatches (generally, or build differences etc.). Doing this may cause a hard-brick IF YOU DON'T follow the instructions CAREFULLY.
1) Get your device to download mode by using this combo "VolumeDown-Home-Power"
2) Open an UP TO DATE ODIN.
3) Find the corresponding .PIT file for your S6 EDGE.
4) Find the corresponding stock rom for your S6 EDGE.
5) Then put them into odin CORRECTLY. Rom to "AP", .pit to PIT
6) Make Sure these are checked: "Re-partition","NAND all erase"
7) Plug your device in and then press start.
After these you should be already flashed correctly without any nand write fail.
---------------------------------------------------------------
-SW REV CHECK FAIL DEVICE: 2 BINARY:1-
This happens when you try to downgrade from 5.1.1... Thanks to Samsung, we can not downgrade to repair our phones or save them because of the locked bootloader. So you have to flash to 5.1.1 again.
If anyone with a working rooted phone, can he/she share his/her own nand backup, so people with screwed boots can recover
or simple delete the hidden.img
Added to the post, thanks mate. Also looking for how to fix corrupted sdcard (theres no mmcblk0x file)
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Please Respond
Malganor said:
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Click to expand...
Click to collapse
I am also getting the exact same thing. I Put in the pit file like instructed as well as the correct rom... still get the same NAND WRITE START.
Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Erase...
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hi guys i think ive bricked my phone
i was installing a custom rom and then it all went t*ts up.
i now cant flash anything through odin and the phone in download mode brings up a error saying Device 3 binary 2
everytime i try to flash anything through odin it brings this up
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU2BOFJ_G925FOXA2BOFJ_G925FXXU2BOFJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin engine v(ID:3.1005)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> sboot.bin
<ID:0/008> NAND Write Start!!
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ive tried flashing different version and also different versions of bootloaders.
i can access recovery and also download mode without any problems i just cant do anything further
when i use adb and type adb devices it doesnt bring anything up
help pleaseeeee
Maybe this might help, http://forum.xda-developers.com/galaxy-s6/general/how-to-fix-rev-check-fail-device-2-t3146522
Hello every body
i have S6 edge that show a green screen "an error has occurred while updating the device software. use the emergency recovvery function in the smart switch pc software"
i tried with smart switch and mention phone dosen't support this type of recovery
i tried flash it with odin and it'mention:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
any solution plz?
Hi...if your problem is still active - not solved! Here a little Note for you that maybe help you to get s6 edge running again.
First you need to start Odin 3.12.03 with Admin rights!!!
Then you could use the Firmware from my Google Drive if you want. Its the German Variant with CSC-DBT
https://drive.google.com/file/d/1pDybynK6_Huu-vjM_azIjgz30IIhlEAP/view?usp=sharing
If you want to use SamFirm by your own. Keep attention that you check the "Binary Nature" !!!!!!!!!!!!!!!!!!!!!!!!!!
If not...its just 1,9 Gb and dont work
If yes...its over 2,3 Gb and work fine
so good luck man