[OnePlus2][CM13] Cannot start phone - OnePlus 2 General

Hey there,
I installed CM13 on my OP2 a few days ago and it worked fine.
Today I accidentally restarted my phone into the fastbootmode and wanted to exit. So I kept holding the power button.
Well, it shutted down. But I can't start it anymore. If it's not charging nothing happens by holding the power button. If the charging cable is plugged in, it vibrates after a while like usual and then the OnePlus Symbol appears for about half a second and then the phone dies again.
Can you guys help me out getting my phone up again?
By the way: I'm completely new with rooting, flashing & xda, so please help me if I've done anything wrong :angel:

CptCrunchy said:
Hey there,
I installed CM13 on my OP2 a few days ago and it worked fine.
Today I accidentally restarted my phone into the fastbootmode and wanted to exit. So I kept holding the power button.
Well, it shutted down. But I can't start it anymore. If it's not charging nothing happens by holding the power button. If the charging cable is plugged in, it vibrates after a while like usual and then the OnePlus Symbol appears for about half a second and then the phone dies again.
Can you guys help me out getting my phone up again?
By the way: I'm completely new with rooting, flashing & xda, so please help me if I've done anything wrong :angel:
Click to expand...
Click to collapse
Did you rebooted to Fastboot mode just after flashing the ROM or you were already on CM13? it's not possible that you brick your device just by enter in fastboot mode something happend but i'm sure there is a solution

Chris-woods said:
Did you rebooted to Fastboot mode just after flashing the ROM or you were already on CM13?
Click to expand...
Click to collapse
No not after flashing, it already worked about a week without any problems...

Can you boot into recovery
Sent from my ONE A2003 using XDA-Developers mobile app

stevoswifty said:
Can you boot into recovery
Click to expand...
Click to collapse
Nope :/ Cannot do anything :/

CptCrunchy said:
Nope :/ Cannot do anything :/
Click to expand...
Click to collapse
Are you sure your phone is charging? Did you flash install a something that requiere root or that could modify your phone is your phone recognize by your computer if you connect it ?

Chris-woods said:
Are you sure your phone is charging?
Click to expand...
Click to collapse
Yes, have tried a second phone on that socket and on that cable
Chris-woods said:
Did you flash install a something that requiere root or that could modify your phone
Click to expand...
Click to collapse
I only rooted it for the installation of CyanogenMod. In the Developersettings, the root is deactivated.
Chris-woods said:
is your phone recognize by your computer if you connect it ?
Click to expand...
Click to collapse
Windows plays the connect sound, but it wont show up on any menue

CptCrunchy said:
Yes, have tried a second phone on that socket and on that cable
I only rooted it for the installation of CyanogenMod. In the Developersettings, the root is deactivated.
Windows plays the connect sound, but it wont show up on any menue
Click to expand...
Click to collapse
try to open command prompt and to type fastboot devices and show me a screenshot or tell me what it says btw were you H2OS Marshmallow or OOS 3.0 Marshmallow before installing CM13 ?

Chris-woods said:
try to open command prompt and to type fastboot devices and show me a screenshot or tell me what it says btw were you H2OS Marshmallow or OOS 3.0 Marshmallow before installing CM13 ?
Click to expand...
Click to collapse
The cmd says nothing. It skips a line and waits for a new input...
Before CM13 I was on OxygenOS 2.1.1 (not flashed)

CptCrunchy said:
The cmd says nothing. It skips a line and waits for a new input...
Before CM13 I was on OxygenOS 2.1.1 (not flashed)
Click to expand...
Click to collapse
Look at this http://forum.xda-developers.com/oneplus-2/general/assistance-solutions-tips-tricks-t3335469

Sounds like another case of stuck volume button, like other people that has had just this problem with stuck in fastboot.

Related

Hard Bricked cant boot hboot & OS

Hi,
I was just above to flash stock rom to receive JB update,
switched my desire then not able to boot into hboot, unable to boot into os.
led is turning on while attaching usb.
please help.
vipinlahoti said:
Hi,
I was just above to flash stock rom to receive JB update,
switched my desire then not able to boot into hboot, unable to boot into os.
led is turning on while attaching usb.
please help.
Click to expand...
Click to collapse
first question, can you boot to bootloader/fastboot?
w1040 said:
first question, can you boot to bootloader/fastboot?
Click to expand...
Click to collapse
No, cant,
no bootloader just led on when attaching cable.
and PC detects as "unknown device attached"
vipinlahoti said:
No, cant,
no bootloader just led on when attaching cable.
and PC detects as "unknown device attached"
Click to expand...
Click to collapse
I think your only option is to restore it via RIFF JTAG... I don't know another way...
vipinlahoti said:
Hi,
I was just above to flash stock rom to receive JB update,
switched my desire then not able to boot into hboot, unable to boot into os.
led is turning on while attaching usb.
please help.
Click to expand...
Click to collapse
Is ur device booting in Qualcomm diagnostic mode.....?
If ur phn does then there is a possibility of flashing stock Rom
If u don't know..just Google it.....!
Sent from my ST25i using Tapatalk 2
@ OP, did you charge it?
Sent from my awesome fridge
yes, from last 2 hrs its on charging.
I donno what is RIFF JTAG and Qualcomm diagnostic mode
googling it....
If you haven't done it yet, pull out the battery, put it back in and try to get into bootloader or recovery. (the pulling out the battery part is important)
by the way, what exactly is happening when you try to boot? please describe step by step what is happening. And what do you mean by boot "into hboot"?
And how did you try to go back to stock? Did you even get into the stock rom. Didn't you just forgot to flash the boot.img when going back to stock?
DeXeS said:
If you haven't done it yet, pull out the battery, put it back in and try to get into bootloader or recovery. (the pulling out the battery part is important)
by the way, what exactly is happening when you try to boot? please describe step by step what is happening. And what do you mean by boot "into hboot"?
And how did you try to go back to stock? Did you even get into the stock rom. Didn't you just forgot to flash the boot.img when going back to stock?
Click to expand...
Click to collapse
to flash a rom I
1. Switched off my phone,
2. hold power + vol down (to boot into bootloader recovery), just blank screen no boot.
3. hold power button + vol up, again just blank screen no boot.
4. when us connected led lights up, and PC detects as "unknown device found".
not booting at all.
vipinlahoti said:
to flash a rom I
1. Switched off my phone,
2. hold power + vol down (to boot into bootloader recovery), just blank screen no boot.
3. hold power button + vol up, again just blank screen no boot.
4. when us connected led lights up, and PC detects as "unknown device found".
not booting at all.
Click to expand...
Click to collapse
but did you remove the battery and put it back in or not? If so and it still does not want to go into bootloader, it really is bricked.. Bring it to a service center for repair..
DeXeS said:
but did you remove the battery and put it back in or not? If so and it still does not want to go into bootloader, it really is bricked.. Bring it to a service center for repair..
Click to expand...
Click to collapse
Tried already but no luck,
Damn mine is rooted and bootloader not sure whether they repair or not
vipinlahoti said:
Tried already but no luck,
Damn mine is rooted and bootloader not sure whether they repair or not
Click to expand...
Click to collapse
If its hard bricked ,they wouldn't no.
..
navmad
mate maybe the screen of your phone has the problem...thats why it shows only blank...
mhb92 said:
mate maybe the screen of your phone has the problem...thats why it shows only blank...
Click to expand...
Click to collapse
That depends, if the device doesn't even shake, then it's not the screen.
Sent from my awesome fridge
Guys, I dont think having any screen problem, bcoz, no vibration during powering on, just a blank screen btw I have given to service center,
just finger crossed

Asus Zenfone 5 wont turn on

Hi, i have problem with zenfone 5. My brother tried to install new android using wireless update in phone(auto update function). So the update downloaded just fine and phone was turned off like its gonna install update but never turned on after this, i tried everything but cant turn it on. I cant even get asus logo, absolutly nothing. When i turn it on charger led dosent show up, tried to enter droidmode(vol up + power) for 10min but nothing. My first guess will be dead MBO but its really weird that this is happen in same time the update was, so probably is something software related.
Bump
Sent from my iOCEAN X7 using Tapatalk
asus zenfone 5 wont turn on
we have same problem, I tried to wipe cache partition for battery consumption purposes but i cancelled it, it seems to long to process erasing the cache so i cancelled it by holding power button + volume up then, wont turn on, itried to charge it, while holding power button + volume up the asus logo appear after that, the battery logo display appear (white side and black battery)
exzzy said:
Hi, i have problem with zenfone 5. My brother tried to install new android using wireless update in phone(auto update function). So the update downloaded just fine and phone was turned off like its gonna install update but never turned on after this, i tried everything but cant turn it on. I cant even get asus logo, absolutly nothing. When i turn it on charger led dosent show up, tried to enter droidmode(vol up + power) for 10min but nothing. My first guess will be dead MBO but its really weird that this is happen in same time the update was, so probably is something software related.
Click to expand...
Click to collapse
hi i am having the exactly same problem, could you tell how did you solve it??
Please i need help.
thank you
Start the phone by pressing power key + volume up and then select the option reboot worked for me!!
Thank you..
It worked for me also, :good:
That's bootloop dude. You need to flash your phone using fastboot. Flash the latest firmware .60 lollipop
Cannot start the phone
AkcezzInc said:
That's bootloop dude. You need to flash your phone using fastboot. Flash the latest firmware .60 lollipop
Click to expand...
Click to collapse
Whats 'the latest firmware .60'? can explain to me how to install it.
Facing the same problem(zenfone 5 not gettting started after update)
Even fastboot is not working for reboot
Pls help...!!!!
Thanx...!!!
skm14747 said:
Even fastboot is not working for reboot
Pls help...!!!!
Thanx...!!!
Click to expand...
Click to collapse
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Hi hendikj
hendikj said:
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Click to expand...
Click to collapse
Could you please explain how to do this tasks as i am new to all these words. pls.
U need to charge u r device Press power + up volume boot into boot loader...unlock bootloader then reboot from fastboot mode...it works for me..
fastboot is not getting open
hendikj said:
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Click to expand...
Click to collapse
i'm not able to open fastboot after update
Thanks. It Worked for me !
williamzerner said:
Start the phone by pressing power key + volume up and then select the option reboot worked for me!!
Click to expand...
Click to collapse
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
davidjay26 said:
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
Click to expand...
Click to collapse
same here! :crying:
Same problem here
davidjay26 said:
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
Click to expand...
Click to collapse
Same over here too, did you solve your problem?

Bootloop and battery won't charge

so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
kuhaku319 said:
so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
Click to expand...
Click to collapse
If there is no other way you can always open the phone and charge the battery manually(if you have the equipment to do that). I had to do that to my phone yesterday(my battery was so low that it wouldn't boot).
BlAckXpeRia said:
If there is no other way you can always open the phone and charge the battery manually(if you have the equipment to do that). I had to do that to my phone yesterday(my battery was so low that it wouldn't boot).
Click to expand...
Click to collapse
how can i remove the case to get the battery out of the phone? its not removable right?
uh. no one?
kuhaku319 said:
how can i remove the case to get the battery out of the phone? its not removable right?
Click to expand...
Click to collapse
You have to use a hairdryer. There are tutorials on YouTube.
kuhaku319 said:
so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
Click to expand...
Click to collapse
The phone should also be able to charge in recovery. Try that.
Btw. I recently flashed a Z2 via flashtool with an unplugged battery (usb power was enough), so you could also try flashing it now although it's empty.
Sent from Note 3, Xiaomi Redmi Note 3.
mr.loverlover said:
You have to use a hairdryer. There are tutorials on YouTube.
The phone should also be able to charge in recovery. Try that.
Btw. I recently flashed a Z2 via flashtool with an unplugged battery (usb power was enough), so you could also try flashing it now although it's empty.
Sent from Note 3, Xiaomi Redmi Note 3.
Click to expand...
Click to collapse
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
kuhaku319 said:
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
Click to expand...
Click to collapse
I would first try to flash just like it is now, without opening the back cover.
Opening the back panel is the last option I would consider, but only if everything else fails.
The thing with opening back cover is, that you will most likely damage you back panel, and you will have to order some new, fake raplecement + the phone won't be waterproof anymore.
And if you can get your phone into fastboot mode (and you've got unlocked bootloader) then just use "adb fastboot flash boot boot.img" command to flash some kernel with recovery.
Sent from Note 3, Xiaomi Redmi Note 3.
kuhaku319 said:
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
Click to expand...
Click to collapse
Have you tryied to plug it in and then press power and volume up continiusly until you fell three vibrations? i think this is for reseting the phone if you continue to press until another vibration it will shut down and maybe then it will charge. Also this thread had helped me before http://forum.xda-developers.com/showthread.php?t=1849170
NatNikos said:
Have you tryied to plug it in and then press power and volume up continiusly until you fell three vibrations? i think this is for reseting the phone if you continue to press until another vibration it will shut down and maybe then it will charge. Also this thread had helped me before http://forum.xda-developers.com/showthread.php?t=1849170
Click to expand...
Click to collapse
Thanks you for the reply
i tried the vol up + power only one time until it vibrates 3 times for the first time and its off, but when i plugged the charger its continues on bootloop cycles thus battery not filling up.
i guess im gonna try until another vibration and see what happen.
and thank you for the link, im gonna give it a try too later, im not home right now, cheers.
kuhaku319 said:
Thanks you for the reply
i tried the vol up + power only one time until it vibrates 3 times for the first time and its off, but when i plugged the charger its continues on bootloop cycles thus battery not filling up.
i guess im gonna try until another vibration and see what happen.
and thank you for the link, im gonna give it a try too later, im not home right now, cheers.
Click to expand...
Click to collapse
Maybe you should try it while plugged in also.
mr.loverlover said:
I would first try to flash just like it is now, without opening the back cover.
Opening the back panel is the last option I would consider, but only if everything else fails.
The thing with opening back cover is, that you will most likely damage you back panel, and you will have to order some new, fake raplecement + the phone won't be waterproof anymore.
And if you can get your phone into fastboot mode (and you've got unlocked bootloader) then just use "adb fastboot flash boot boot.img" command to flash some kernel with recovery.
Sent from Note 3, Xiaomi Redmi Note 3.
Click to expand...
Click to collapse
yeah i tried flashing it but the phone is totally dead, pc wont detect the phone because the phone is dead. that's the issue im facing now :silly:
NatNikos said:
Maybe you should try it while plugged in also.
Click to expand...
Click to collapse
tried, still bootlooped, when i hold power + vol up while plugged in, its powered on again and started bootlooping again
im just wondering. did u use flashtool to flash the ftf again?
Dilesh Perera said:
im just wondering. did u use flashtool to flash the ftf again?
Click to expand...
Click to collapse
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
kuhaku319 said:
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
Click to expand...
Click to collapse
ok try like this
1 put phone off ( u can press the little red button inside the left side flap till it vibrate 3 times )
2 disconnect the cable from Pc
3 open flashtool and select FLASHMODE select the ftf u going to flash
4 once the flashtool request to connect the phone connect the phone while keep on pressing the vol button
it should flash the ftf
kuhaku319 said:
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
Click to expand...
Click to collapse
It won't probably charge in fastboot/flashmode.
But it's very strange that the PC won't detect your phone when trying to enter flashmode.
Because, as I said earlier, I was able to get Z2 into flashmode without any power (battery taken out).
There should be some change in device manager when you connect the device.
Are you sure all the drivers are installed on your PC?
Dilesh Perera said:
ok try like this
1 put phone off ( u can press the little red button inside the left side flap till it vibrate 3 times )
2 disconnect the cable from Pc
3 open flashtool and select FLASHMODE select the ftf u going to flash
4 once the flashtool request to connect the phone connect the phone while keep on pressing the vol button
it should flash the ftf
Click to expand...
Click to collapse
mr.loverlover said:
It won't probably charge in fastboot/flashmode.
But it's very strange that the PC won't detect your phone when trying to enter flashmode.
Because, as I said earlier, I was able to get Z2 into flashmode without any power (battery taken out).
There should be some change in device manager when you connect the device.
Are you sure all the drivers are installed on your PC?
Click to expand...
Click to collapse
Solved
Apparently the driver is acting weird, but i uninstalled all z2 driver and reinstall them, all working and can be flashed
Thank you guys for helping me :fingers-crossed::highfive:

my mobile not working

I m able to got call but I can't see anything on screen it is just 1 month old....what to do now?? I see some scratch...
You rooted? Or like DarkAlpha.Sete asks:
DarkAlpha.Sete said:
What did you do before it stopped working?
(Did you make an update, tried unlocking bootloader, installing a custom recovery or custom ROM?)
Click to expand...
Click to collapse
If there's something that you are modifying, this could introduce bugs.. if you are stock unrooted, and if you can get download mode booted, just plug it into your pc and flash stock again.. moto I'm not as familiar with versus samsung, but I'm sure you can flash stock
sj
Sent from my rooted SM-G920P on stock Nougat 7.0 using [email protected] Pro
ZeroVirus said:
I m able to got call but I can't see anything on screen it is just 1 month old....what to do now?? I see some scratch...
Click to expand...
Click to collapse
What did you do before it stopped working?
(Did you make an update, tried unlocking bootloader, installing a custom recovery or custom ROM?)
No it's comes out from my pocket
ZeroVirus said:
No it's comes out from my pocket
Click to expand...
Click to collapse
Sorry but I don't understand what you mean by "it comes out from my pocket". Could you please explain in another way?
Also can you enter download/fastboot mode? Press and hold the power button and volume up(or down, I don't know what is your device) to enter it.
I see clear crack on LCD...i feel vibrate but I can't see anything
ZeroVirus said:
I see clear crack on LCD...i feel vibrate but I can't see anything
Click to expand...
Click to collapse
Well, sorry if I am wrong, but if you have a clear crack, and you don't see anything when you turn it on(but it vibrates), probably the problem is the LCD.
You can try following the steps that I wrote to enter fastboot. If you can enter it and make the last step show the serial number, but still don't see anything on the screen, then there is a high chance that the problem is the LCD.
Firstly, install the ADB and Fastboot drivers (if you already have them, skip this). The easiest method I know to install them is by using this installer
Make sure the device is powered off(holding power button by around 15 seconds should force a shut down if it is on)
Hold power button and volume down key to enter fastboot (or try?) until it vibrates
Now, connect the device to your PC with an USB cable
On the folder where you have the drivers, open a command window. (Shift + Right Click, then "Open command window here")
Type
Code:
fastboot devices
If a serial number is printed, then, the problem is the screen and not the device itself
I have attached a screenshot with an example(my device output).
If this doesn't work, then I'm sorry but I don't know much more to do.
I say again: I'm not any professional, all of this is my knowledge... I can be wrong
ZeroVirus said:
I m able to got call but I can't see anything on screen it is just 1 month old....what to do now?? I see some scratch...
Click to expand...
Click to collapse
Did what I said worked? You didn't reply for a long time...

Question Please I need help - hard brick

hello,
I bought a CN version of gt, I unlocked the bootloader and changed the rom. Then I got again in twrp and pressed on reboot - then my phone bricked. It is not responding, and when I connect it to my pc, it connects and disconnects every 10 seconds while the cable still plugged in.
I don't know what to do, I spent 400$ on something that I can't use...
thanks.
Atalephinio said:
hello,
I bought a CN version of gt, I unlocked the bootloader and changed the rom. Then I got again in twrp and pressed on reboot - then my phone bricked. It is not responding, and when I connect it to my pc, it connects and disconnects every 10 seconds while the cable still plugged in.
I don't know what to do, I spent 400$ on something that I can't use...
thanks.
Click to expand...
Click to collapse
You can reflash the rom with realme flash tool。(https://androidmtk.com/realme-flash-tool) ----Sorry for making a mistake earlier
Have you tried it?
yiyinglaohu said:
You can reflash the rom with MIFLASH。(https://c.mi.com/oc/miuidownload/detail?guide=1 )or (http://www.miui.com/shuaji-393.html)
Click to expand...
Click to collapse
but the problem is that it is connecting and disconnecting every few seconds
Atalephinio said:
but the problem is that it is connecting and disconnecting every few seconds
Click to expand...
Click to collapse
Try to get into fastboot mode first . Your situation seems to be that the ADB driver is not fully installed
you can find it on google
yiyinglaohu said:
Try to get into fastboot mode first . Your situation seems to be that the ADB driver is not fully installed
Click to expand...
Click to collapse
how??? it is not responding when I am pressing on the buttons. It is hard bricked.
no fastboot no recovery. nothing - just black screen.
Atalephinio said:
hello,
I bought a CN version of gt, I unlocked the bootloader and changed the rom. Then I got again in twrp and pressed on reboot - then my phone bricked. It is not responding, and when I connect it to my pc, it connects and disconnects every 10 seconds while the cable still plugged in.
I don't know what to do, I spent 400$ on something that I can't use...
thanks.
Click to expand...
Click to collapse
try vol "down" +" power" button, if it'll go to recovery stable you can use adb commands
or
vol "up"+"down"+"power" (3 buttons in total) and when you see chinese letters just relesease them. if its succesful, you'll see bootloader menu
grown_man said:
try vol "down" +" power" button, if it'll go to recovery stable you can use adb commands
or
vol "up"+"down"+"power" (3 buttons in total) and when you see chinese letters just relesease them. if its succesful, you'll see bootloader menu
Click to expand...
Click to collapse
I wish it was my situation... I tried it nothing happens.
Atalephinio said:
I wish it was my situation... I tried it nothing happens.
Click to expand...
Click to collapse
then i suggest official repair services
Atalephinio: "but the problem is that it is connecting and disconnecting every few seconds"​"no fastboot no recovery. nothing - just black screen"
You probably only have EDL mode active. I think only MSM Download Tool will help you. However, but this is a paid service.
This is my opinion, but maybe someone more experienced should have a say.
Try to press three buttons (vol up- vol down- power) during 40 seconds aprox....
May only use 9008 mode.
I solved it. The only solution is to pay to someone who got msmtool.
This problem happens when you flash another rom through twrp on gt, it erases the recovery of the phone and then when the phone is trying to go to recovery it becomes bricked .
If you want to avoid it use the commands of adb and fastboot through the computer (not through the phone itself).
I paid 15$ to @hoangzk9 he solved the problem.
Big thanks.
Atalephinio said:
I solved it. The only solution is to pay to someone who got msmtool.
This problem happens when you flash another rom through twrp on gt, it erases the recovery of the phone and then when the phone is trying to go to recovery it becomes bricked .
If you want to avoid it use the commands of adb and fastboot through the computer (not through the phone itself).
I paid 15$ to @hoangzk9 he solved the problem.
Big thanks.
Click to expand...
Click to collapse
As I know that realme gt dont public the flash tool so we need contact to the services to get they help.
Same with you, I have some problem when I tried to flash twrp to realme phone. No luck and my phone became hard brick. But you can send an email to eu services of realme, they can help without any paid.
Good to know.

Categories

Resources