Good day
Permission to post
I was here to seek help on how to fix my sony xperia Z2
I was flashing my Z2 but accidentally I didn't notice that i click the wrong firmware
and my z2 is not booting. it said that failed to update the new system.
please help me I dont know what to do.
damulag1234 said:
Good day
Permission to post
I was here to seek help on how to fix my sony xperia Z2
I was flashing my Z2 but accidentally I didn't notice that i click the wrong firmware
and my z2 is not booting. it said that failed to update the new system.
please help me I dont know what to do.
Click to expand...
Click to collapse
Hi
Do Flash a New Rom of your Phone with Flashtools v 0.9.18.5
sєňţ ғяom тнe ҡıňɢ ♔ Z2
Sajad Askari said:
Hi
Do Flash a New Rom of your Phone with Flashtools v 0.9.18.5
sєňţ ғяom тнe ҡıňɢ ♔ Z2
Click to expand...
Click to collapse
my z2 is turned off and i cant open it to allow usb debugging sir,
what should I do? i think my z2 got brick
damulag1234 said:
my z2 is turned off and i cant open it to allow usb debugging sir,
what should I do? i think my z2 got brick
Click to expand...
Click to collapse
No problem
Just install Flashtools V 0.9.18.5
And install Your Drivers
And Do flash Your Rom
No need usb Debugging
Are You Can Flash Stock ROM?
sєňţ ғяom тнe ҡıňɢ ♔ Z2
Unless you've messed up the TA partition, our phones are pretty hard to brick. If you hold vol_up then plug in USB to your PC, it should boot into flash mode with a blue LED. That means you can use Flashtool to flash an FTF file to the phone, effectively factory program it.
Si_NZ said:
Unless you've messed up the TA partition, our phones are pretty hard to brick. If you hold vol_up then plug in USB to your PC, it should boot into flash mode with a blue LED. That means you can use Flashtool to flash an FTF file to the phone, effectively factory program it.
Click to expand...
Click to collapse
my z2 is turned off and i already flashed but i used a wrong firmware.
my z2 now is not opening or booting and it say The software update failed
what should i do?
damulag1234 said:
Good day
Permission to post
I was here to seek help on how to fix my sony xperia Z2
I was flashing my Z2 but accidentally I didn't notice that i click the wrong firmware
and my z2 is not booting. it said that failed to update the new system.
please help me I dont know what to do.
Click to expand...
Click to collapse
Hey, don't worry if you do these steps exactly then your phone will boot again normally and you can enter the recovery then flash any rom again and recover your phone from this brick
1- Download and install Minimal ADB and Fastboot from this link: https://www.androidfilehost.com/?fid=24521665358595410
2- Download and install Flashtool drivers from this link: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
Skip Step 2 if you already installed Flashtool Drivers that install with Flashtool if you have installed it.
3- Download the latest twrp recovery from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img
4- Move the twrp recovery that you have downloaded in step 3 to this Path C:\Program Files\Minimal ADB and Fastboot
5- Download this kernel from this link: https://drive.google.com/file/d/0Bwn7bAJ-USZjZzg0Q2I2RWlWa1U/view?pref=2&pli=1
6- Extract it then you will find boot.img take this file and move it too to this Path C:\Program Files\Minimal ADB and Fastboot
7- put your phone in fastboot mode by this way >> (Power off your phone completely then wait for 10 second then press and hold the volume up then connect your phone to the computer with usb cable while you are pressing and holding the volume up then the led will change it's color to blue.. that is the fastboot mode)
8- Now go to the Minimal ADB and Fastboot folder in that path (C:\Program Files\Minimal ADB and Fastboot) Press shift button from keyboard then press right click form mouse while pressing the shift button you will find an option [Open command window here] Press it.
9- In the command window write this command exactly: fastboot flash recovery twrp-3.0.2-0-sirius.img
10- Then write this command after it: fastboot flash boot boot.img
11- After it flashed successfully reboot your phone by writing this command: fastboot reboot then unplug the usb from the phone
12- when the phone reboot and the sony logo appears keep pressing the volume up and down until the twrp recovery opens
13- Done
Through the recovery flash any custom or stock rom and your phone will boot normally
I wish that i had helped you if you want any thing just ask me and i will answer.
Mostafa Sherif said:
Hey, don't worry if you do these steps exactly then your phone will boot again normally and you can enter the recovery then flash any rom again and recover your phone from this brick
1- Download and install Minimal ADB and Fastboot from this link: https://mega.nz/#!7942XJjI!9gurv7k3P...RTiDPeArhwjXsG XB9c
2- Download and install Flashtool drivers from this link: http://doomlord.xperia-files.com/dow...41LTIwMTQwMzE4
Skip Step 2 if you already installed Flashtool Drivers that install with Flashtool if you have installed it.
3- Download the latest twrp recovery from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img.html
4- Move the twrp recovery that you have downloaded in step 3 to this Path C:\Program Files\Minimal ADB and Fastboot
5- Download this kernel from this link: https://drive.google.com/file/d/0Bwn...ew?usp=sharing
6- Extract it then you will find boot.img take this file and move it too to this Path C:\Program Files\Minimal ADB and Fastboot
7- put your phone in fastboot mode by this way >> (Power off your phone completely then wait for 10 second then press and hold the volume up then connect your phone to the computer with usb cable while you are pressing and holding the volume up then the led will change it's color to blue.. that is the fastboot mode)
8- Now go to the Minimal ADB and Fastboot folder in that path (C:\Program Files\Minimal ADB and Fastboot) Press shift button from keyboard then press right click form mouse while pressing the shift button you will find an option [Open command window here] Press it.
9- In the command window write this command exactly: fastboot flash recovery twrp-3.0.2-0-sirius.img
10- Then write this command after it: fastboot flash boot boot.img
11- After it flashed successfully reboot your phone by writing this command: fastboot reboot then unplug the usb from the phone
12- when the phone reboot and the sony logo appears keep pressing the volume up and down until the twrp recovery opens
13- Done
Through the recovery flash any custom or stock rom and your phone will boot normally
I wish that i had helped you if you want any thing just ask me and i will answer.
Click to expand...
Click to collapse
i need the key to download can you provide it for me?
damulag1234 said:
i need the key to download can you provide it for me?
Click to expand...
Click to collapse
Ok, no problem but for which one?!
Mostafa Sherif said:
Ok, no problem but for which one?!
Click to expand...
Click to collapse
sir can you provide me all the needed files? the download links are not working. and the other needs key to be downloaded
damulag1234 said:
sir can you provide me all the needed files? the download links are not working. and the other needs key to be downloaded
Click to expand...
Click to collapse
Sorry for this problem,, but i have edited my post and provided you with a new alternative link (for Minimal ADB and Fastboot) see it again.
and i will check the other links now and if any another link is unavailable i will change it for you.
Mostafa Sherif said:
Ok, no problem but for which one?!
Click to expand...
Click to collapse
1. download link need key
2. download link is not working
3. downloaded
5.download link is not working
damulag1234 said:
1. download link need key
2. download link is not working
3. downloaded
5.download link is not working
Click to expand...
Click to collapse
Check now all the download links again,, it should works now normally
Tell me if there is any another thing
Sorry for that
Mostafa Sherif said:
Check now all the download links again,, it should works now normally
Tell me if there is any another thing
Sorry for that
Click to expand...
Click to collapse
how to use md5 file? do i just need to paste it?
damulag1234 said:
how to use md5 file? do i just need to paste it?
Click to expand...
Click to collapse
Where do you get these files?? i didn't tell you to use any md5 file. and there is no md5 file to use it and if you have found any md5 file just ignore it and continue doing these steps only.
Do the steps as i write it and your phone will boot again successfully
Mostafa Sherif said:
Where do you get these files?? i didn't tell you to use any md5 file. and there is no md5 file to use it and if you have found any md5 file just ignore it.
Do the steps as i write it and your phone will boot again successfully
Click to expand...
Click to collapse
the twrp file is an md5 file sir
damulag1234 said:
the twrp file is an md5 file sir
Click to expand...
Click to collapse
Download the twrp.img from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img
After you download it you will see it's name is twrp-3.0.2-0-sirius.img
Then continue my steps normally and tell me if there is any problem
Mostafa Sherif said:
Hey, don't worry if you do these steps exactly then your phone will boot again normally and you can enter the recovery then flash any rom again and recover your phone from this brick
1- Download and install Minimal ADB and Fastboot from this link: https://www.androidfilehost.com/?fid=24521665358595410
2- Download and install Flashtool drivers from this link: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
Skip Step 2 if you already installed Flashtool Drivers that install with Flashtool if you have installed it.
3- Download the latest twrp recovery from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img
4- Move the twrp recovery that you have downloaded in step 3 to this Path C:\Program Files\Minimal ADB and Fastboot
5- Download this kernel from this link: https://drive.google.com/file/d/0Bwn7bAJ-USZjZzg0Q2I2RWlWa1U/view?pref=2&pli=1
6- Extract it then you will find boot.img take this file and move it too to this Path C:\Program Files\Minimal ADB and Fastboot
7- put your phone in fastboot mode by this way >> (Power off your phone completely then wait for 10 second then press and hold the volume up then connect your phone to the computer with usb cable while you are pressing and holding the volume up then the led will change it's color to blue.. that is the fastboot mode)
8- Now go to the Minimal ADB and Fastboot folder in that path (C:\Program Files\Minimal ADB and Fastboot) Press shift button from keyboard then press right click form mouse while pressing the shift button you will find an option [Open command window here] Press it.
9- In the command window write this command exactly: fastboot flash recovery twrp-3.0.2-0-sirius.img
10- Then write this command after it: fastboot flash boot boot.img
11- After it flashed successfully reboot your phone by writing this command: fastboot reboot then unplug the usb from the phone
12- when the phone reboot and the sony logo appears keep pressing the volume up and down until the twrp recovery opens
13- Done
Through the recovery flash any custom or stock rom and your phone will boot normally
I wish that i had helped you if you want any thing just ask me and i will answer.
Click to expand...
Click to collapse
sir i cant understand the instruction on number 8 and 9
would you mind explaining it to me? thanks a lot
damulag1234 said:
sir i cant understand the instruction on number 8 and 9
would you mind explaining it to me? thanks a lot
Click to expand...
Click to collapse
No problem In step 8 first: Go to the path i told you in the description then press and hold shift button from keyboard and then press right click with mouse at any empty space in the folder,, a menu will pop up then you will find an option named (Open command window here) select it, then a command window will open.
I wish i had descriped it to you exactly and tell me if you successed to make it
If you do step 8 correctly then continue to step 9.. in step 9, you have to write the commands that i give it to you in the command window that have been opened in step 8.
The commands that i had bold it
Mostafa Sherif said:
No problem In step 8 first: Go to the path i told you in the description then press and hold shift button from keyboard and then press right click with mouse at any empty space in the folder,, a menu will pop up then you will find an option named (Open command window here) select it, then a command window will open.
I wish i had descriped it to you exactly and tell me if you successed to make it
If you do step 8 correctly then continue to step 9.. in step 9, you have to write the commands that i give it to you in the command window that have been opened in step 8.
The commands that i had bold it
Click to expand...
Click to collapse
i followed it what about the number 10? should i put it before i enter the command from number 9?
Related
Hi,
I'm on the process of installing ClockWorkMod Recovery, stupid of me i forgot to enable USB Debugging option on my phone. Now I'm stuck on Command Prompt saying...
C:\Fastboot>fastboot flash boot recovery-nozomi.img
< waiting for device >
It has been sitting for more than 5 minutes as I am typing now. Should I disconnect the USB cord? Would this action brick my phone?
Sorry for my stupidity!
cybrkada said:
Hi,
I'm on the process of installing ClockWorkMod Recovery, stupid of me i forgot to enable USB Debugging option on my phone. Now I'm stuck on Command Prompt saying...
C:\Fastboot>fastboot flash boot recovery-nozomi.img
< waiting for device >
It has been sitting for more than 5 minutes as I am typing now. Should I disconnect the USB cord? Would this action brick my phone?
Sorry for my stupidity!
Click to expand...
Click to collapse
How are you installing it ???
Via flash tool??
And nope your phone won't brick
I disconnected the cord. Turned on the phone and noticed that USB Debugging is ticked/checked. So I repeated the process but I am still getting..
< waiting for device >
What should I do?
soulhackereborn said:
How are you installing it ???
Via flash tool??
And nope your phone won't brick
Click to expand...
Click to collapse
Yes, via Flastool. Yeah my phone did not get bricked! :good:
cybrkada said:
Yes, via Flastool. Yeah my phone did not get bricked! :good:
Click to expand...
Click to collapse
can u give the link for this recovery you triein to push through flashtool and the turorial if possible...
soulhackereborn said:
can u give the link for this recovery you triein to push through flashtool and the turorial if possible...
Click to expand...
Click to collapse
Hi soulhackereborn!
Sorry for the late reply! Sorry the forum prevented me from posting the URL as I am just a new user here.
"To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!"
Anyway the tutorial says (copy&paste):
Use the computer for downloading the CWM file from here.
Then, on the same computer download fastboot from here.
Extract fastboot on C:\ drive.
Then, copy the downloaded “ecovery-nozomi.img” file to the Fastboot folder from your computer.
Now you must connect the phone in fastboot mode with the computer.
In order to do so you must plug the USB cord to the PC, then on your phone press and hold the Volume Up button and while doing this connect the USB cable to your Xperia S.
Up next, on the PC click on “Start -> Accessories -> on Command prompt right click -> Run as administrator”.
The command prompt window will now be displayed.
Now, enter the following commands (press enter after each one): “cd c:\Fastboot” and “fastboot flash boot recovery-nozomi.img”.
CWM will now be flashed.
In the end the “finished / OKAY” message should be displayed.
In command prompt enter “fastboot reboot”.
Your handset should now reboot into ClockworkMod recovery.
Remove the USB cord and disconnect the Xperia S from the computer.
cybrkada said:
Hi soulhackereborn!
Sorry for the late reply! Sorry the forum prevented me from posting the URL as I am just a new user here.
"To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!"
Anyway the tutorial says (copy&paste):
Use the computer for downloading the CWM file from here.
Then, on the same computer download fastboot from here.
Extract fastboot on C:\ drive.
Then, copy the downloaded “ecovery-nozomi.img” file to the Fastboot folder from your computer.
Now you must connect the phone in fastboot mode with the computer.
In order to do so you must plug the USB cord to the PC, then on your phone press and hold the Volume Up button and while doing this connect the USB cable to your Xperia S.
Up next, on the PC click on “Start -> Accessories -> on Command prompt right click -> Run as administrator”.
The command prompt window will now be displayed.
Now, enter the following commands (press enter after each one): “cd c:\Fastboot” and “fastboot flash boot recovery-nozomi.img”.
CWM will now be flashed.
In the end the “finished / OKAY” message should be displayed.
In command prompt enter “fastboot reboot”.
Your handset should now reboot into ClockworkMod recovery.
Remove the USB cord and disconnect the Xperia S from the computer.
Click to expand...
Click to collapse
everything seems to be good in the tutorial though..
But what is it a kernel, rom or an CWM image file ???
if still it says waiting for device then here's a couple things you should check :-
1) Fastboot ie; S1 Boot driver installed or no
2) Switch off phone and connect it to the PC via usb holding Volume + button (this is fastboot mode)
3) Check does your device remain in fastboot mode or no i mean purple led light glows stays on continuously or no until u execute the command, if not reinstall the driver and try again
4) If everything well till now try flashing with the given commands without the quotes ie; fastboot flash boot recovery-nozomi.img
soulhackereborn said:
everything seems to be good in the tutorial though..
But what is it a kernel, rom or an CWM image file ???
if still it says waiting for device then here's a couple things you should check :-
1) Fastboot ie; S1 Boot driver installed or no
2) Switch off phone and connect it to the PC via usb holding Volume + button (this is fastboot mode)
3) Check does your device remain in fastboot mode or no i mean purple led light glows stays on continuously or no until u execute the command, if not reinstall the driver and try again
4) If everything well till now try flashing with the given commands without the quotes ie; fastboot flash boot recovery-nozomi.img
Click to expand...
Click to collapse
1. I dont know how to check, it should be installed as i unlock the bootloader yesterday. I actually manually updated it on Device Manager.
2. I understand this.
3. On my case, it's a blue LED lit steadily after doing step 2. I am using Sony Xperia S.
4. Yes, i flashed them without the quotes.
cybrkada said:
1. I dont know how to check, it should be installed as i unlock the bootloader yesterday. I actually manually updated it on Device Manager.
2. I understand this.
3. On my case, it's a blue LED lit steadily after doing step 2. I am using Sony Xperia S.
4. Yes, i flashed them without the quotes.
Click to expand...
Click to collapse
Try rebooting both your PC and phone... This is a small thing but always helps and one more thing after switching off the phone n before connecting it in fastboot mode let der be a gap of alteat a min or two
Is this tutorial on xda or some other forum if on xda then try messaging me the link or tel me forum sub forum topic and title
Usually <waiting for device> can show up when you don't have proper drivers installed. Double check them if you haven't done so.
soulhackereborn said:
Try rebooting both your PC and phone... This is a small thing but always helps and one more thing after switching off the phone n before connecting it in fastboot mode let der be a gap of alteat a min or two
Is this tutorial on xda or some other forum if on xda then try messaging me the link or tel me forum sub forum topic and title
Click to expand...
Click to collapse
I dont see PM here, i think I am still restricted.
see if the link helps, i removed w w w
android.gs/install-clockworkmod-recovery-sony-xperia-s
i'm rebooting them after this.. thanks
LiveSquare said:
Usually <waiting for device> can show up when you don't have proper drivers installed. Double check them if you haven't done so.
Click to expand...
Click to collapse
Which drivers? I have already downloaded SDK and I believe the S1 driver is installed yesterday when i unlock the bootloader.
i rebooted both the PC and the CP, but i am still getting < waiting for device >...
by the way is the ADB from tutorial the SDK one?
cybrkada said:
i rebooted both the PC and the CP, but i am still getting < waiting for device >...
by the way is the ADB from tutorial the SDK one?
Click to expand...
Click to collapse
Dude as far as I know there is no need to check/ tick USB debugging for fastboot... It's just for flashtool..
Try re -installing the drivers again manually or let windows search over internet...
Finally, i made it! thanks to both of you!
fastboot.exe seems to be corrupted!
Problem solved!
Just last one question, now that i have CWM recovery on my phone, is it already rooted? sorry i am beginner...
cybrkada said:
Just last one question, now that i have CWM recovery on my phone, is it already rooted? sorry i am beginner...
Click to expand...
Click to collapse
Yes ur rooted!!
Thanks!
I'm currently downloading Cyanogenmod ver 9.1. Hopefully it works! Thank you so much buddy! You have been very helpful! If I get problems on flashing CM9.1, i'll contact you , hehe
One of the reminders on isntalling CM9 is:
Make sure that your Xperia S is already running a rooted firmware, and that it has the ClockworkMod Recovery properly installed.
How do I know I have a rooted firmware? Do I still need to flash FTF file?
By the way, I am getting a boot loop from CWM recovery, I cant go to the homescreen, no option to turn off! It only reboots the CWM.
(Still downloading CM9 as of the moment)
Hi, I tried to install a custom JB rom on my Sony Xperia U but now I'm in a reboot loop when i connect my device to the computer it connects and disconnects all the time cannot even flash please help thanks.
Are you connecting it off, then holding Vol - to trigger fastboot on USB? Don't do it when it's bootlooping.
Check the following things:
1 you have unlocked bootloader.
2 you have Xperia u fastboot and flashing drivers properly installed.
Reinstall drivers if you aren't sure whether they're properly installed or not
3 you said you're getting bootloop so your device isn't bricked..
4 take out the battery and insert again and press volume down button for flashmode and flash stock ics
5 flash boot.img from kernel zip file in FASTBOOT MODE.. If you're not sure how to do that there's a guide available in forum.. Search for it
6 then reboot to recovery, do wipes, then flash the Rom...
7 reboot twice
8 second reboot takes 10 mins don't freak out its normal
9 enjoy
AD9295 said:
Check the following things:
1 you have unlocked bootloader.
2 you have Xperia u fastboot and flashing drivers properly installed.
Reinstall drivers if you aren't sure whether they're properly installed or not
3 you said you're getting bootloop so your device isn't bricked..
4 take out the battery and insert again and press volume down button for flashmode and flash stock ics
5 flash boot.img from kernel zip file in FASTBOOT MODE.. If you're not sure how to do that there's a guide available in forum.. Search for it
6 then reboot to recovery, do wipes, then flash the Rom...
7 reboot twice
8 second reboot takes 10 mins don't freak out its normal
9 enjoy
Click to expand...
Click to collapse
Thanks!, It worked my device is working normally now .. but I can't really find a guide on how to install the boot.img can you please link me to it ? thanks.
GoldenMikez said:
Thanks!, It worked my device is working normally now .. but I can't really find a guide on how to install the boot.img can you please link me to it ? thanks.
Click to expand...
Click to collapse
the command for fastboot is
fastboot flash boot boot.img
the boot.img file must be in same folder as fastboot
there are two methods :
i recommend second method..
1. using command prompt
procedure - download adb and fastboot drivers.. extract them anywhere in pc.. copy the boot.img file to that extracted folder (i cant find the thread which contains the link for the drivers but u can definitely get it by google-ing it)
press and hold shift and right click..
select open command window here
switch off your phone
hold vol up key on ur phone and connect it to pc.. (blue led will come up)
then pass the command in command prompt as - fastboot flash boot boot.img
or
2 using flashtool
open flashtool
switch off your phone
hold vol up key on ur phone and connect it to pc.. u'll see in the flashtool that - device connected in fastboot mode
then clickon flash button and select fastboot
click on select kernel to flash and select boot.img which u extracted from kernel file..
Do these steps quickly.. fastboot mode automatically shuts down after 15-20 seconds and ur phone will start charging itself..
after flashing jb kernel reboot in recovery and then follow next steps
Enjoyy
reboot loop
im in a bootloop with a phantom kernel and i didnt place the rom in the phone storage, the telephone is rebooting again and again. i can acces to the CWM but i don't know how i can transplant the rom now :crying: thanks
I am trying to install CWM on my HTC desire 601 from rogers canada
As per instruction from this website
http://www.thetechbulletin.com/how-to-root-htc-desire-601-and-install-cwm-recovery-3281/
I tried this method
Rooting requirements
Fully charge your device, before following the process it should be charged at least 70%.
Enable USB debugging mode on your device, go to Settings->Applications-> Development-> USB debugging mode.
Unlock bootloader from here HTCdev.
Download Recovery package [mandatory]
Download ADB
Download SuperSU
How to root HTC Desire 601 and install CWM recovery
Switch of your device after downloading all the files from the above link to your computer.
Press Volume Down + Power button for few seconds, here you will see options called fastboot, using volume key select this option.
Now you need to connect your device to your PC using USB cable.
Now extract the ADB file and save it on your desktop
Copy the recovery package you have downloaded to the folder where you have extracted the ABD file.
Now open the command prompt there from that folder, press Shift+Right Click and choose the option ‘open command prompt here‘ and write the following command.
fastboot flash recovery philz_touch_6.08.7-zara.img
This will install CWM recovery on your device. After completion of the process just reboot it.
Now again connect your device to your PC and transfer the SuperSU zip file to your device’s SD card.
Now Turn off your device and boot into recovery mode, to do so Volume Down+Power Button and this time select recovery using volume rocker Key.
In recovery mode you will see several option, select ‘install zip from SD card‘ and browse the file you just copied into your device’s SD card and hit enter to begin the rooting process.
That’s it, you have successfully installed CWM and rooted your HTC Desire 601.
When i try to flash recovery image using this command
fastboot flash recovery philz_touch_6.08.7-zara.img
its coming back with an error message
C:\Users\Owner\Desktop\Android Unlocking Tools\HTC desire 601\android>fastboot
flash recovery philz_touch_6.08.7-zara. img
target reported max download size of 801906688 bytes
error: cannot load 'philz_touch_6.08.7-zara.': No error
Could anybody please help me in this
PS : I already unlocked boot loader and trying to install CWM on this phone
R u on jb or kk?
Child's Play said:
R u on jb or kk?
Click to expand...
Click to collapse
, I have no idea , this phone i got is stuck on HTC screen , I am not sure about OS on this one. This is my friends phone and he doest know what OS was on there
Jellybean or kitkat
Child's Play said:
Jellybean or kitkat
Click to expand...
Click to collapse
I have no idea , this phone i got is stuck on HTC screen , I am not sure about OS on this one. This is my friends phone and he doest know what OS was on there, i can send you bootloader screenshot if that helps
Yeah show me
Child's Play said:
Yeah show me
Click to expand...
Click to collapse
Attached are the images for bootloader screens
U r on kk. That recovery is for jb. Flash twrp for kk http://forum.xda-developers.com/showthread.php?t=2804520
Child's Play said:
U r on kk. That recovery is for jb. Flash twrp for kk http://forum.xda-developers.com/showthread.php?t=2804520
Click to expand...
Click to collapse
Downloaded recovery image file from the link you provided
came back with same error message
target reported max download size of 801906688 bytes
error: cannot load 'openrecovery.img': No error
Put the recovery.img in the platform-tools folder and hold the shift key and right-click in the empty space then select "open command window here" then flash the recovery.img via fastboot
Child's Play said:
Put the recovery.img in the platform-tools folder and hold the shift key and right-click in the empty space then select "open command window here" then flash the recovery.img via fastboot
Click to expand...
Click to collapse
Thats what i did , but sorry never seen this message before , i have flashed few HTC before. Do you know what this error message means ?
No i googled this http://android.stackexchange.com/qu...error-cannot-load-recovery-clockwork-no-error
Child's Play said:
Put the recovery.img in the platform-tools folder and hold the shift key and right-click in the empty space then select "open command window here" then flash the recovery.img via fastboot
Click to expand...
Click to collapse
Thanks a lot , its done , just bit USB port issue , CWM is installed now I am trying to do insertcoin rom on this one. Will let you know how it goes ...
Great!
Im getting the same error message.
It also wont let me unlock the bootloader on the HTC website. Is the anyway you can help me out -- Child's Play-- It says an error after i submit my token i have no clue and its very important to that i get root lol if you know what i mean . All my drivers are updated everything is correct. Could it possibly be because i downloaded a command prompt , only because my windows xp doesnt pop up with a command line option when i shift+right click. PLEASE i really need help im so frustrated and i dont give up lol. thanks guys
Make sure you copy only the code, not the empty space. Token doesn't like the empty space
HELP ! HELP ! HELP !
hard bricked by flashing a miui rom from twrp without deleting the emmc file :crying::crying::crying::crying::crying::crying:
i can only go to fastboot , no recovery , miui logo for 3 seconds
please someone help me !!! :crying::crying:
will the test point work ?
Edit :-
Thank you all , i managed to unbtick using test point .!!
I know enough to tell you that I'd you can get fastboot yo work, its not bricked. Honestly I don't own the device. I own lg g3. And it might be different for this device but you can try pushing recovery from fasyboot mode using your PC. You might wanna google how to tbh and ask around ppl with similar device if possible. Pushing through fastboot/adb is most common so pushing recovery will format recovery partition and install/push new one. That will get you working recovery. (I hope). Happy flashing.
In fastboot check if bootloader is locked by running the device info command... It is not locked you have hopes... Use fastboot to flash fastboot rom package with modified emmc file and modded image...
Its locked
Only way is to do test point method or take it to a service center
#BATMAN# said:
HELP ! HELP ! HELP !
hard bricked by flashing a miui rom from twrp without deleting the emmc file :crying::crying::crying::crying::crying::crying:
i can only go to fastboot , no recovery , miui logo for 3 seconds
please someone help me !!! :crying::crying:
will the test point work ?
Click to expand...
Click to collapse
try 1. this:http://en.miui.com/thread-235865-1-1.html
2. http://en.miui.com/thread-244814-1-1.html
3.http://en.miui.com/forum.php?mod=viewthread&tid=257227&highlight=test%2Bpoint%2Bredmi%2Bnote%2B3
4.http://en.miui.com/thread-245347-1-1.html
Let me know if you have succes!Good luck!
Luiggi79 said:
try 1. this:http://en.miui.com/thread-235865-1-1.html
2. http://en.miui.com/thread-244814-1-1.html
3.http://en.miui.com/forum.php?mod=viewthread&tid=257227&highlight=test%2Bpoint%2Bredmi%2Bnote%2B3
4.http://en.miui.com/thread-245347-1-1.html
Let me know if you have succes!Good luck!
Click to expand...
Click to collapse
im trying now , thank you , i will tel the results
didnt work , and i didn't try the testpoint yet because im afried , can some one help me
*when connect via fastboot it shows android bootloader interface ( im new to adb someone helpme with this )
*when connect holding ( volume up+volume down+power ) it shows =HS-USB diagnostics 900E ( i manually updated this driver to 9008 but mi flash dosent show it )
*when trying to flash via fastboot it says "FAILED : remote ; device is locked"
faced the same problem bro better give it in care if dnt wnt to give it to care just go to( http://en.miui.com/thread-235865-1-1.html ) or try ( http://xiaomitips.com/guide/fix-bricked-redmi-note-3-no-unlock-permission/ ) this if all didnt work go to care bro
#BATMAN# said:
im trying now , thank you , i will tel the results
didnt work , and i didn't try the testpoint yet because im afried , can some one help me
*when connect via fastboot it shows android bootloader interface ( im new to adb someone helpme with this )
*when connect holding ( volume up+volume down+power ) it shows =HS-USB diagnostics 900E ( i manually updated this driver to 9008 but mi flash dosent show it )
*when trying to flash via fastboot it says "FAILED : remote ; device is locked"
Click to expand...
Click to collapse
Steps:
A).On the computer in windows disable driver signature enforcement featrure and turn off any protection like security suites,AV software or firewalls.To disable driver signature enforcement you must open command prompt and type:a)bcdedit.exe -set loadoptions ENABLE_INTEGRITY_CHECKS and press enter
b)bcdedit.exe -set TESTSIGNING ON and press enter
c)reboot computer
d) install MI flash after reboot;download it from here :http://en.miui.com/thread-235865-1-1.html
B) On the phone:
1.Hold Vol - and Vol + and plug Usb cable in computer&phone
2.download ADB files from here http://en.miui.com/thread-235865-1-1.html
3.extract files from archive to folder
4. in this folder,where you have extracted adb files press:shift on keyboard and right click on the mouse in the same time and choose "open command window here"
5.in command window type:a)adb devices and press enter
b)adb reboot edl and press enter
Now you are in download mode
6.from device manager install qualcomm driver;it should be seen in other devices section;right click---update driver----navigate to :C/Program files(X86)/XIaomi/Mi flash/Qualcomm/Driver;Note:you need x64 windows computer for this operation
7.start MI flash---right click and run as administrator;browse for rom folder,you need a fastboot rom(the rom need with suffix tgz to be;not zip).Put the tgz archive(rom) in Local Disk C and extract with winrar!!!!!!(use winrar) to folder;rename the created folder to ROM.In MI flash when do browse for folder SELECT ENTIRE FOLDER NOT JUST THE FOLDER IMAGES.OK?
8.in MI Flash window press refresh button from up side;the device should appear on the list
9.in MI Flash windows in the down side of windows tick the litlle circle who say:Flash all
10.Press flash button from up
1.1. Wait until it finish flashing procedure:should appear in the right side from device peration completed succesfully
12.Remove usb cable and press power button on the device;keep the power button pressed until the device give you a vibration,the release it
Luiggi79 said:
Steps:
A).On the computer in windows disable driver signature enforcement featrure and turn off any protection like security suites,AV software or firewalls.To disable driver signature enforcement you must open command prompt and type:a)bcdedit.exe -set loadoptions ENABLE_INTEGRITY_CHECKS and press enter
b)bcdedit.exe -set TESTSIGNING ON and press enter
c)reboot computer
d) install MI flash after reboot;download it from here :http://en.miui.com/thread-235865-1-1.html
B) On the phone:
1.Hold Vol - and Vol + and plug Usb cable in computer&phone
2.download ADB files from here http://en.miui.com/thread-235865-1-1.html
3.extract files from archive to folder
4. in this folder,where you have extracted adb files press:shift on keyboard and right click on the mouse in the same time and choose "open command window here"
5.in command window type:a)adb devices and press enter
b)adb reboot edl and press enter
Now you are in download mode
6.from device manager install qualcomm driver;it should be seen in other devices section;right click---update driver----navigate to :C/Program files(X86)/XIaomi/Mi flash/Qualcomm/Driver;Note:you need x64 windows computer for this operation
7.start MI flash---right click and run as administrator;browse for rom folder,you need a fastboot rom(the rom need with suffix tgz to be;not zip).Put the tgz archive(rom) in Local Disk C and extract with winrar!!!!!!(use winrar) to folder;rename the created folder to ROM.In MI flash when do browse for folder SELECT ENTIRE FOLDER NOT JUST THE FOLDER IMAGES.OK?
8.in MI Flash window press refresh button from up side;the device should appear on the list
9.in MI Flash windows in the down side of windows tick the litlle circle who say:Flash all
10.Press flash button from up
1.1. Wait until it finish flashing procedure:should appear in the right side from device peration completed succesfully
12.Remove usb cable and press power button on the device;keep the power button pressed until the device give you a vibration,the release it
Click to expand...
Click to collapse
im trying now! hopefully it will work :good::good:
#BATMAN# said:
im trying now , thank you , i will tel the results
didnt work , and i didn't try the testpoint yet because im afried , can some one help me
*when connect via fastboot it shows android bootloader interface ( im new to adb someone helpme with this )
*when connect holding ( volume up+volume down+power ) it shows =HS-USB diagnostics 900E ( i manually updated this driver to 9008 but mi flash dosent show it )
*when trying to flash via fastboot it says "FAILED : remote ; device is locked"
Click to expand...
Click to collapse
I have the same problem.
I can get Miflash to show when under fastboot but it doesn't show the COM port but the device id similar if you check Fastboot Devices. but can't flash due to device is locked.
I tried QFIL as well but it can't go into Emergency Download Mode.
Anyone Please help.
Stuck at mi logo
Device unlocked
bootloader unlocked
twrp working
how to get rid of this
fylim said:
I have the same problem.
I can get Miflash to show when under fastboot but it doesn't show the COM port but the device id similar if you check Fastboot Devices. but can't flash due to device is locked.
I tried QFIL as well but it can't go into Emergency Download Mode.
Anyone Please help.
Click to expand...
Click to collapse
me too , im still searching for a solution ......:crying::crying::crying::crying::crying:
the only solution i found was the test point but im trying to fix it without opening my phone
i you find anything please let me know !!!!!!!!!!!!!!!!
avrrv3689 said:
Device unlocked
bootloader unlocked
twrp working
how to get rid of this
Click to expand...
Click to collapse
if you don't need TWRP and want MIUI rom try this http://en.miui.com/thread-267263-1-1.html ...
and
if you don't want miui rom flash the new aosp one
#BUT DONT FLASH MIUI ROM USING TWRP IF YOU UNLOCKED THE BOOTLOADER UNOFFICIALY#
#BATMAN# said:
if you don't need TWRP and want MIUI rom try this http://en.miui.com/thread-267263-1-1.html ...
and
if you don't want miui rom flash the new aosp one
#BUT DONT FLASH MIUI ROM USING TWRP IF YOU UNLOCKED THE BOOTLOADER UNOFFICIALY#
Click to expand...
Click to collapse
finlly got out of it
thanxx
can u suggest a procedure to unlock bootloader and root the device and twrp without bricking or bootloop
avrrv3689 said:
finlly got out of it
thanxx
can u suggest a procedure to unlock bootloader and root the device and twrp without bricking or bootloop
Click to expand...
Click to collapse
Read these carefully #DO AT YOUR OWN RISK#
http://forum.xda-developers.com/redmi-note-3/how-to/unlock-instruction-unlock-bootloader-t3355904
http://forum.xda-developers.com/redmi-note-3/how-to/unlock-bootloader-twrp-root-7-2-3-t3359492
http://forum.xda-developers.com/redmi-note-3/how-to/redmi-note3-prokenzo-guiderom-global-t3341102
:good: hit thanks if i helped you :good:
#BATMAN# said:
if you don't need TWRP and want MIUI rom try this http://en.miui.com/thread-267263-1-1.html ...
and
if you don't want miui rom flash the new aosp one
#BUT DONT FLASH MIUI ROM USING TWRP IF YOU UNLOCKED THE BOOTLOADER UNOFFICIALY#
Click to expand...
Click to collapse
"BUT DONT FLASH MIUI ROM USING TWRP IF YOU UNLOCKED THE BOOTLOADER UNOFFICIALY"
If bootloader is unlocked officially then can we flash any MIUI recovery ROM using TWRP without need of modifying Recovery ROM (deleting bootloader file , patch boot.img) ? can we switch to any MIUI ROM then easily ?
akhil17kr said:
"BUT DONT FLASH MIUI ROM USING TWRP IF YOU UNLOCKED THE BOOTLOADER UNOFFICIALY"
If bootloader is unlocked officially then can we flash any MIUI recovery ROM using TWRP without need of modifying Recovery ROM (deleting bootloader file , patch boot.img) ? can we switch to any MIUI ROM then easily ?
Click to expand...
Click to collapse
Yes i think you can but im not 100% sure :good::good:
#BATMAN# said:
Yes i think you can but im not 100% sure :good::good:
Click to expand...
Click to collapse
Oh Lol , have asked many people but none of them are sure about this .. but i have asked from mi chat they said once bootloader is unlocked you can't lock it back by flashing MIUI roms as it's security feature . SO we can say unofficial method is problem if you like to switch to between ROM's but official one will not create any problems ..still not sure though have to ask who have done through Official method.
fylim said:
I have the same problem.
I can get Miflash to show when under fastboot but it doesn't show the COM port but the device id similar if you check Fastboot Devices. but can't flash due to device is locked.
I tried QFIL as well but it can't go into Emergency Download Mode.
Anyone Please help.
Click to expand...
Click to collapse
The solution:
1. Press and hold VolUp+VolDown+Power (all 3 buttons) at the same time.
2. The MI logo will appear for some time, and then disappear, don't release the buttons.
3. The MI logo will then appear briefly, and then disappear. Now release all 3 buttons.
4. Connect the phone to PC, and then proceed to use MiFlash as usual.
Use a 64-bit PC
Take a look here http://en.miui.com/forum.php?mod=viewthread&tid=228048&page=6#pid4518713
http://en.miui.com/thread-228048-1-1.html
To enter in download mode see this youtube video:https://www.youtube.com/watch?v=4Fs5n3W1c8U
---------- Post added at 12:10 PM ---------- Previous post was at 12:07 PM ----------
#BATMAN# said:
me too , im still searching for a solution ......:crying::crying::crying::crying::crying:
the only solution i found was the test point but im trying to fix it without opening my phone
i you find anything please let me know !!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
The solution:
1. Press and hold VolUp+VolDown+Power (all 3 buttons) at the same time.
2. The MI logo will appear for some time, and then disappear, don't release the buttons.
3. The MI logo will then appear briefly, and then disappear. Now release all 3 buttons.
4. Connect the phone to PC, and then proceed to use MiFlash as usual.
Use a 64-bit PC
Take a look here: http://en.miui.com/forum.php?mod=viewthread&tid=228048&page=6#pid4518713
http://en.miui.com/thread-228048-1-1.html
How to enter in download mode see this youtube video :https://www.youtube.com/watch?v=4Fs5n3W1c8U
Luiggi79 said:
The solution:
1. Press and hold VolUp+VolDown+Power (all 3 buttons) at the same time.
2. The MI logo will appear for some time, and then disappear, don't release the buttons.
3. The MI logo will then appear briefly, and then disappear. Now release all 3 buttons.
4. Connect the phone to PC, and then proceed to use MiFlash as usual.
Use a 64-bit PC
Take a look here http://en.miui.com/forum.php?mod=viewthread&tid=228048&page=6#pid4518713
http://en.miui.com/thread-228048-1-1.html
To enter in download mode see this youtube video:https://www.youtube.com/watch?v=4Fs5n3W1c8U
---------- Post added at 12:10 PM ---------- Previous post was at 12:07 PM ----------
The solution:
1. Press and hold VolUp+VolDown+Power (all 3 buttons) at the same time.
2. The MI logo will appear for some time, and then disappear, don't release the buttons.
3. The MI logo will then appear briefly, and then disappear. Now release all 3 buttons.
4. Connect the phone to PC, and then proceed to use MiFlash as usual.
Use a 64-bit PC
Take a look here: http://en.miui.com/forum.php?mod=viewthread&tid=228048&page=6#pid4518713
http://en.miui.com/thread-228048-1-1.html
How to enter in download mode see this youtube video :https://www.youtube.com/watch?v=4Fs5n3W1c8U
Click to expand...
Click to collapse
didn't work for me !:crying::crying:
Hello all, as I can install drivers for fastboot on my machine, I tried everything and still can not admit it, the team also stays in the black screen, just turn on the LED in blue, my machine has Windows 10, has something to seeing that, I would appreciate your help, really.
1- Download and install the latest Flashtool driver for Xperia Z2 from here: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
2- Download and install Minimal ADB and Fastboot Setup v1.4 from this link: https://mega.nz/#!7942XJjI!9gurv7k3PVVFT8VViDbkg_sUiRTiDPeArhwjXsG XB9c
3- Download Xperia_Z2_driver.zip from this link: http://dl-developer.sonymobile.com/drivers/Xperia_Z2_driver.zip
4- Extract Xperia_Z2_driver.zip
5- Connect your Xperia Z2 with Computer by USB in (fastboot mode)
6- Press right click on My Computer icon then click on Properties.
7- In the new window that will open on the upper left side press on Device Manager.
8- Search in Device Manager window for Protable Devices, when you find it just press on (+) beside it.. when you extend it you will see Unknown device or your Xperia Z2 or some thing like that.
9- Right click on it and press on Update Driver Software.
10- In the new window select (Browser my computer for driver software) then click on Browse.. and choose the extracted folder from Xperia_Z2_driver.zip you have downloaded in Step 1,,, be sure that Include subfolders is checked then press next.
11- Done it must be installed and your phone must be regonized and work successfully in the fastboot mode.
Note <<<<<<<>>>>>>>> the most important thing in (Step 5) that when you start to install the fastboot driver for your phone you must put your phone in the fastboot mode don't forget that.
If there is anything not work with you or you need more description in it just tell me and i will help you.
I hope that i have helped you.
Reboot to windows 10 using advanced startup with disable driver signature. Then install whatever drivers u want to install. And also install flashtool driver from there. Happy flashing :good:
rakeshbro said:
Reboot to windows 10 using advanced startup with disable driver signature. Then install whatever drivers u want to install. And also install flashtool driver from there. Happy flashing :good:
Click to expand...
Click to collapse
Mostafa Sherif said:
1- Download and install the latest Flashtool driver for Xperia Z2 from here: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
2- Download and install Minimal ADB and Fastboot Setup v1.4 from this link: https://mega.nz/#!7942XJjI!9gurv7k3PVVFT8VViDbkg_sUiRTiDPeArhwjXsG XB9c
3- Download Xperia_Z2_driver.zip from this link: http://dl-developer.sonymobile.com/drivers/Xperia_Z2_driver.zip
4- Extract Xperia_Z2_driver.zip
5- Connect your Xperia Z2 with Computer by USB in (fastboot mode)
6- Press right click on My Computer icon then click on Properties.
7- In the new window that will open on the upper left side press on Device Manager.
8- Search in Device Manager window for Protable Devices, when you find it just press on (+) beside it.. when you extend it you will see Unknown device or your Xperia Z2 or some thing like that.
9- Right click on it and press on Update Driver Software.
10- In the new window select (Browser my computer for driver software) then click on Browse.. and choose the extracted folder from Xperia_Z2_driver.zip you have downloaded in Step 1,,, be sure that Include subfolders is checked then press next.
11- Done it must be installed and your phone must be regonized and work successfully in the fastboot mode.
Note <<<<<<<>>>>>>>> the most important thing in (Step 5) that when you start to install the fastboot driver for your phone you must put your phone in the fastboot mode don't forget that.
If there is anything not work with you or you need more description in it just tell me and i will help you.
I hope that i have helped you.
Click to expand...
Click to collapse
Hi thanks for the guide and files and have installed the drivers, dual recovery've roteado, and install the first room, no problems, but now wanting to install one based 6.0.1 stayed in a loop, as I can enter recovery mode, or as I can flash the stock, because in flashtool not recognize me the phone, trying to select the room to flash me nothing appears, or where I can download the roms stock? please help
ermite666 said:
Hi thanks for the guide and files and have installed the drivers, dual recovery've roteado, and install the first room, no problems, but now wanting to install one based 6.0.1 stayed in a loop, as I can enter recovery mode, or as I can flash the stock, because in flashtool not recognize me the phone, trying to select the room to flash me nothing appears, or where I can download the roms stock? please help
Click to expand...
Click to collapse
If you install Marshmallow Rom and it just stayed in a loop so you have to flash the bootloop fix for Marshmallow 6.0.1 that will fix this problem and the rom will boot successfuly :
1- Flash Marshmallow rom you want through the recovery.
2- Download this bootloop fix from this link: https://mega.nz/#!AJcwERiQ!FUmk6eS5aoVsFSZ1f4WZIELIt7sckPCj11n0AIdCNzU
3- Copy it to your phone or sd card then flash this bootloop fix through the recovery.
4- Reboot and the rom will boot successfully without any bootloop.
I wish that i had helped you.
If there is anything just ask me and i will answer you
Mostafa Sherif said:
If you install Marshmallow Rom and it just stayed in a loop so you have to flash the bootloop fix for Marshmallow 6.0.1 that will fix this problem and the rom will boot successfuly :
1- Flash Marshmallow rom you want through the recovery.
2- Download this bootloop fix from this link: https://mega.nz/#!AJcwERiQ!FUmk6eS5aoVsFSZ1f4WZIELIt7sckPCj11n0AIdCNzU
3- Copy it to your phone or sd card then flash this bootloop fix through the recovery.
4- Reboot and the rom will boot successfully without any bootloop.
I wish that i had helped you.
If there is anything just ask me and i will answer you
Click to expand...
Click to collapse
I'm searching a way to recover my forever-looping phone. I had the Android M, got the horribel ideia of using kingroot via PC and now the phone does not go to the OS. I've tried everything, I´m gonna try installing all drivers again (windows 10). Anyway, What can I do since I dont have recovery mode ?
Plus, when I try to flash a fresh rom, I get this;
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I dunno whatelse to do. It's like the PC do not recognize the phone. The little brick just vibrates and loops.
---------- Post added at 03:55 PM ---------- Previous post was at 03:35 PM ----------
YEAH. I managed to reboot system via flashtool. MIRACLE.
Rickpg said:
I'm searching a way to recover my forever-looping phone. I had the Android M, got the horribel ideia of using kingroot via PC and now the phone does not go to the OS. I've tried everything, I´m gonna try installing all drivers again (windows 10). Anyway, What can I do since I dont have recovery mode ?
Plus, when I try to flash a fresh rom, I get this;
I dunno whatelse to do. It's like the PC do not recognize the phone. The little brick just vibrates and loops.
---------- Post added at 03:55 PM ---------- Previous post was at 03:35 PM ----------
YEAH. I managed to reboot system via flashtool. MIRACLE.
Click to expand...
Click to collapse
Ok bro. just come down we can solve it by two ways:
The first one by unlocking your bootloader then install recovery then flash a new rom through recovery.
The second way is to keep the bootloader locked and recover your phone by using flashtool and any ftf for xperia z2
So which way from the two ways you want to solve your phone by it?
Mostafa Sherif said:
Ok bro. just come down we can solve it by two ways:
The first one by unlocking your bootloader then install recovery then flash a new rom through recovery.
The second way is to keep the bootloader locked and recover your phone by using flashtool and any ftf for xperia z2
So which way from the two ways you want to solve your phone by it?
Click to expand...
Click to collapse
I guess the bootloader is unlocked, so I would like to flash the recovery. Is there a way to do it via Flashtool?
The phone now iwont even loop. It's stucked in the SONY logo. -_-
Hi thanks, I found the way, now what I need is how to root, I've tried with dual recovery, but send me error, and what I managed to do it is with kingroot, then with dual recovery and only then is installed or I have done something wrong? thanks again
Rickpg said:
I guess the bootloader is unlocked, so I would like to flash the recovery. Is there a way to do it via Flashtool?
The phone now iwont even loop. It's stucked in the SONY logo. -_-
Click to expand...
Click to collapse
If the bootloader unlocked so you can easily flash recovery by using fastboot commands by using these steps:
1- download and install Minimal ADB and Fastboot from this link: https://mega.nz/#!7942XJjI!9gurv7k3PVVFT8VViDbkg_sUiRTiDPeArhwjXsG XB9c
2- Download and install Flashtool drivers from this link: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
Skip Step 2 if you already installed Flashtool Drivers that install with Flashtool if you have installed it.
3- Download the latest twrp recovery from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img.html
4- Move the twrp recovery that you have downloaded in step 3 to this Path C:\Program Files\Minimal ADB and Fastboot
5- put your phone in fastboot mode by this way >> (Power off your phone completely then wait for 10 second then press and hold the volume up then connect your phone to the computer with usb cable while you are pressing and holding the volume up then the led will change it's color to blue.. that is the fastboot mode)
6- Now go to the Minimal ADB and Fastboot folder in that path (C:\Program Files\Minimal ADB and Fastboot) Press shift button from keyboard then press right click form mouse while pressing the shift button you will find an option [Open command window here] Press it.
7- In the command window write this command exactly: fastboot flash recovery twrp-3.0.2-0-sirius.img
8- After it flashed successfully reboot your phone by writing this command: fastboot reboot then unplug the usb from the phone
9- when the phone reboot and the sony logo appear keep pressing the volume up and down until the twrp recovery opens
10- That is it.. you can from it wipe data, system, cache, dalivk cache and flash any rom you want
After you successfully flash a recovery just tell me and i will help you in flashing a new rom through the recovery
This way works only if you have bootloader unlocked
I wish i had helped you
---------- Post added at 06:04 PM ---------- Previous post was at 06:03 PM ----------
ermite666 said:
Hi thanks, I found the way, now what I need is how to root, I've tried with dual recovery, but send me error, and what I managed to do it is with kingroot, then with dual recovery and only then is installed or I have done something wrong? thanks again
Click to expand...
Click to collapse
Now you have a recovery right??
Mostafa Sherif said:
If the bootloader unlocked so you can easily flash recovery by using fastboot commands by using these steps:
1- download and install Minimal ADB and Fastboot from this link: https://mega.nz/#!7942XJjI!9gurv7k3PVVFT8VViDbkg_sUiRTiDPeArhwjXsG XB9c
2- Download and install Flashtool drivers from this link: http://doomlord.xperia-files.com/download.php?dlid=Rmxhc2h0b29sLWRyaXZlcnMtMS41LTIwMTQwMzE4
Skip Step 2 if you already installed Flashtool Drivers that install with Flashtool if you have installed it.
3- Download the latest twrp recovery from this link: https://dl.twrp.me/sirius/twrp-3.0.2-0-sirius.img.html
4- Move the twrp recovery that you have downloaded in step 3 to this Path C:\Program Files\Minimal ADB and Fastboot
5- put your phone in fastboot mode by this way >> (Power off your phone completely then wait for 10 second then press and hold the volume up then connect your phone to the computer with usb cable while you are pressing and holding the volume up then the led will change it's color to blue.. that is the fastboot mode)
6- Now go to the Minimal ADB and Fastboot folder in that path (C:\Program Files\Minimal ADB and Fastboot) Press shift button from keyboard then press right click form mouse while pressing the shift button you will find an option [Open command window here] Press it.
7- In the command window write this command exactly: fastboot flash recovery twrp-3.0.2-0-sirius.img
8- After it flashed successfully reboot your phone by writing this command: fastboot reboot then unplug the usb from the phone
9- when the phone reboot and the sony logo appear keep pressing the volume up and down until the twrp recovery opens
10- That is it.. you can from it wipe data, system, cache, dalivk cache and flash any rom you want
After you successfully flash a recovery just tell me and i will help you in flashing a new rom through the recovery
This way works only if you have bootloader unlocked
I wish i had helped you
---------- Post added at 06:04 PM ---------- Previous post was at 06:03 PM ----------
Now you have a recovery right??
Click to expand...
Click to collapse
The flashin recovery did work but the phone does not turn on now. The power button only vibrates but it's all turned off...
Since I´m dealing with my phone from early mornin I dunno if there is a lack of battery. I´m loosing contacts with clients today =(
Rickpg said:
The flashin recovery did work but the phone does not turn on now. The power button only vibrates but it's all turned off...
Since I´m dealing with my phone from early mornin I dunno if there is a lack of battery. I´m loosing contacts with clients today =(
Click to expand...
Click to collapse
Sony logo doesn't appear after pressing the power button and vibrate??
Try to make hard reset by press and hold volume up button and press and hold the power button too until the mobile vibrates 3 times then wait for 10 seconds and try to power on the phone again normally and tell me if the sony logo has
OR wait
I knew the solution and i will write it now
---------- Post added at 07:28 PM ---------- Previous post was at 07:16 PM ----------
Rickpg said:
The flashin recovery did work but the phone does not turn on now. The power button only vibrates but it's all turned off...
Since I´m dealing with my phone from early mornin I dunno if there is a lack of battery. I´m loosing contacts with clients today =(
Click to expand...
Click to collapse
The solution as following:
1- Make hard reset first as i descriped in the previous post to make sure that the phone powered off completely.
2- Download this kernel from this link: https://drive.google.com/file/d/0Bwn7bAJ-USZjZzg0Q2I2RWlWa1U/view?usp=sharing
3- Extract it then you will find boot.img take this file and move it too to this Path C:\Program Files\Minimal ADB and Fastboot
4- As i descriped go to Minimal ADB and Fastboot folder and press shift then right click and select Open command window here
5- Put your phone in fastboot mode by press and hold volume up and connect it with usb cable
6- Write the following command: fastboot flash recovery twrp-3.0.2-0-sirius.img
7- Then write this command after it: fastboot flash boot boot.img
8- Now reboot your phone by writing: fastboot reboot then unplug the usb from phone
9- When the sony logo appear press the volume up and down until it go into the recovery
10- Done
When the recovery opens successfully tell me if you want and i will help you to flash a new rom from the recovery
Mostafa Sherif said:
Sony logo doesn't appear after pressing the power button and vibrate??
Try to make hard reset by press and hold volume up button and press and hold the power button too until the mobile vibrates 3 times then wait for 10 seconds and try to power on the phone again normally and tell me if the sony logo has
OR wait
I knew the solution and i will write it now
---------- Post added at 07:28 PM ---------- Previous post was at 07:16 PM ----------
The solution as following:
1- Make hard reset first as i descriped in the previous post to make sure that the phone powered off completely.
2- Download this kernel from this link: https://drive.google.com/file/d/0Bwn7bAJ-USZjZzg0Q2I2RWlWa1U/view?usp=sharing
3- Extract it then you will find boot.img take this file and move it too to this Path C:\Program Files\Minimal ADB and Fastboot
4- As i descriped go to Minimal ADB and Fastboot folder and press shift then right click and select Open command window here
5- Put your phone in fastboot mode by press and hold volume up and connect it with usb cable
6- Write the following command: fastboot flash recovery twrp-3.0.2-0-sirius.img
7- Then write this command after it: fastboot flash boot boot.img
8- Now reboot your phone by writing: fastboot reboot then unplug the usb from phone
9- When the sony logo appear press the volume up and down until it go into the recovery
10- Done
When the recovery opens successfully tell me if you want and i will help you to flash a new rom from the recovery
Click to expand...
Click to collapse
You are amazing. *..*
Can I wipe everything and install vi recovery the "D6503_Customized US_1281-9709_23.5.A.0.575_R3D flashable-prerooted-signed" ?
Rickpg said:
You are amazing. *..*
Can I wipe everything and install vi recovery the "D6503_Customized US_1281-9709_23.5.A.0.575_R3D flashable-prerooted-signed" ?
Click to expand...
Click to collapse
Yup you can
1- Make factory reset
2- Wipe > Data, Cache, System and Dalivk/ART cache
3- Download and flash D6503_Customized US_1281-9709_23.5.A.0.575_R3D flashable-prerooted-signed from this link: https://drive.google.com/open?id=0B-xW4tRK0miyc1RJWGZXQUZKYjA
4- Reboot
5- [This is an optional step maybe you need for it and maybe not] If you flashed this rom and you stuck in a bootloop or anything didn't work probably then flash this bootloop fix from this link: https://mega.nz/#!AJcwERiQ!FUmk6eS5aoVsFSZ1f4WZIELIt7sckPCj11n0AIdCNzU
6- Done
Mostafa Sherif said:
Yup you can
1- Make factory reset
2- Wipe > Data, Cache, System and Dalivk/ART cache
3- Download and flash D6503_Customized US_1281-9709_23.5.A.0.575_R3D flashable-prerooted-signed from this link: https://drive.google.com/open?id=0B-xW4tRK0miyc1RJWGZXQUZKYjA
4- Reboot
5- [This is an optional step maybe you need for it and maybe not] If you flashed this rom and you stuck in a bootloop or anything didn't work probably then flash this bootloop fix from this link: https://mega.nz/#!AJcwERiQ!FUmk6eS5aoVsFSZ1f4WZIELIt7sckPCj11n0AIdCNzU
6- Done
Click to expand...
Click to collapse
I just love when we get a happy ending lol :silly:
Thank you and keep up the good work.
Rickpg said:
I just love when we get a happy ending lol :silly:
Thank you and keep up the good work.
Click to expand...
Click to collapse
Hahahahahahahahahahaha You are welcome anytime my bro.
Because marshmallow not allow me to enter recovery, according install the ROM comes with preinstalled root and recovery and nothing
ermite666 said:
Because marshmallow not allow me to enter recovery, according install the ROM comes with preinstalled root and recovery and nothing
Click to expand...
Click to collapse
No no bro, you can enter recovery in marshmallow but instead of keep pressing on volume up as in lollipop to enter the recovery, in marshmallow you have to keep pressing on volume down to enter the recovery when you reboot your phone and the sony logo appears
So try and tell me