I got some dust particles on the inside of the lens which really annoys me. Due to this the camera does not focus correctly.
I really want to keep the phone waterproof so i am afraid to take it apart to clean it. Anyone experience similar issues or even swapped the backcover? Any recommendations for a backcover that ensures waterproof ability after swapping it?
thanks!
quickstyler said:
I got some dust particles on the inside of the lens which really annoys me. Due to this the camera does not focus correctly.
I really want to keep the phone waterproof so i am afraid to take it apart to clean it. Anyone experience similar issues or even swapped the backcover? Any recommendations for a backcover that ensures waterproof ability after swapping it?
thanks!
Click to expand...
Click to collapse
If you're getting dust under the lens you're obviously not water tight. I have ordered a replacement back and it cracked just picking it up. I don't know how fragile the original is but I'd be very careful while removing it. New seals can be bought for a few bucks.
not sure where this came from - the body is 100% waterproof...maybe "dust" particle is not the correct explanation
maybe is scratch dots from keys in you pocket?
it abit look like dust...
i mixed my pockets by mistake and left few dots maybe u did it lots of times.. ( i know the lens is plastic and not scratch resistance ) so i try to avoid keys in the same pocket
Superrman said:
maybe is scratch dots from keys in you pocket?
it abit look like dust...
i mixed my pockets by mistake and left few dots maybe u did it lots of times.. ( i know the lens is plastic and not scratch resistance ) so i try to avoid keys in the same pocket
Click to expand...
Click to collapse
the scratches on the outside of the lens are no problem since the sony coated this and also polishing is working quite well. also i checked this several times with a magnifier.
i have uploaded a picture of the particle that causes the faulty autofocus. at the picture on the right you can see that this is on the inside of the lens.
since the phone is waterproof this is quite clearly a production fault but since i need the phone for my everyday work and life issuing a rma at sony is no option for me.
i was just wondering is someone else experienced anything similar or swapped the backcover and tested waterproof
You can test your waterproofness of your phone to do the pressure test in the service menu.
Go to dialer and dial *#*#service#*#*, go to service test and then pressure sensor. The value indicated on the screen should increase by pressing on your screen when the phone is still waterproof.
Sent from my E5823 using XDA-Developers mobile app
Alcedii said:
You can test your waterproofness of your phone to do the pressure test in the service menu.
Go to dialer and dial *#*#service#*#*, go to service test and then pressure sensor. The value indicated on the screen should increase by pressing on your screen when the phone is still waterproof.
Sent from my E5823 using XDA-Developers mobile app
Click to expand...
Click to collapse
How much does yours go up? Mine started at 997 millbar and goes up to 1002 millbar max when I started seeing discoloration from pushing the LCD too hard.
civicsr2cool said:
How much does yours go up? Mine started at 997 millbar and goes up to 1002 millbar max when I started seeing discoloration from pushing the LCD too hard.
Click to expand...
Click to collapse
that's fine. Mine is also just a few millibar. try it with the simtray flap open. It won't increase a bit.
quickstyler said:
the scratches on the outside of the lens are no problem since the sony coated this and also polishing is working quite well. also i checked this several times with a magnifier.
i have uploaded a picture of the particle that causes the faulty autofocus. at the picture on the right you can see that this is on the inside of the lens.
since the phone is waterproof this is quite clearly a production fault but since i need the phone for my everyday work and life issuing a rma at sony is no option for me.
i was just wondering is someone else experienced anything similar or swapped the backcover and tested waterproof
Click to expand...
Click to collapse
Hi
I have had the same kind of dust in my XZ5
I sent it back and they have exchanged with a new device.
Manufacturing issue... It could happen
Sent from my HTC 10 using XDA-Developers mobile app
since sony support couldn't offer me an adequate solution for their manufacturing error I decided to find a solution by myself.
primary most important was for me that i do not open the device.
I got rid of the particle by freezing the phone in the freezer for 20min and tapping on the lens. The particle fell off and now somewhere i do not care about )
if someone has a similar issue this might be also an alternative solution
Same problem here. It supprises me the presition in which this product was conceived with programmed obsolescence. Just after guaranty ended I began to notice blurs and dust.
I suppose gaskets became less performant as they get harder and they can't hold pressure changes anymore, like when you take a plane or enter a tunnel in a train.
Vic021 said:
Same problem here. It supprises me the presition in which this product was conceived with programmed obsolescence. Just after guaranty ended I began to notice blurs and dust.
I suppose gaskets became less performant as they get harder and they can't hold pressure changes anymore, like when you take a plane or enter a tunnel in a train.
Click to expand...
Click to collapse
I have the same translucent gray dust spots on my rear camera, and tapping and bumping with strenght makes them moving around. Of course this is programmed obsolescence.
Moreover they fill phones with glue and adhesives for "water-proofness" purposes... but after 2 years of daily use, noone sane minded would submerge any phone and if you have the need, you can't easily fix anything inside the phone or change battery if you aren't a technician , because you have to use professional tools to melt glue and move parts.
That's the current world of "water-proof", thin smartphones.
Something must change if we don't want to swim in oceans made of electronic rubbish in the near future.
Related
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
SecUpwN said:
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
Click to expand...
Click to collapse
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
richyrocket said:
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
Click to expand...
Click to collapse
Thank you so much for stating this, exactly what I was talking about! Kind of a small release to hear I didn't buy faulty hardware. Do we have other readers here who can confirm that this behavior is normal?
I'll head out to the phone store today to double check. Still, does an app exist to check for hardware failures?
Yes no faulty equipment, it is normal on every single Evo.
( Don't ask for help as I couldn't care if your phone explodes, eh)
flashallthetime said:
Yes no faulty equipment, it is normal on every single Evo.
Click to expand...
Click to collapse
You just saved my whole HTC experience. Thank you soo much! How come this is the case on every EVO? Isn't that something draining the battery?
No it is actually bleeding from the main screen, I guess there's a small gap between the search button and the screen
( Don't ask for help as I couldn't care if your phone explodes, eh)
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Use your phone in the dark. Watch until soft buttons stop glowing. See the light behind the search button?
Mine has it too.
Sent from my HTC EVO 3D X515m using xda app-developers app
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Turn the backlight of touch buttons off using kernel tuner and keep screen on, you will notice light behind search key.
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
dessolator666 said:
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
Click to expand...
Click to collapse
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
SecUpwN said:
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
Click to expand...
Click to collapse
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
dessolator666 said:
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
That would actually be the coolest contribution I've seen in a ling time! Are you really willing to do that for our EVO community? If you did, you'd be our king.
Don't worry, it's on every EVO 3D. From GSM to CDMA.
The light bleed is from the screen back light. It does give the phone a cheap feel sometimes, but it's a common problem.
It's not as prevalent on cm10 with inverted gapps
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
flashallthetime said:
It's not as prevalent on cm10 with inverted gapps
Click to expand...
Click to collapse
How come?
SecUpwN said:
How come?
Click to expand...
Click to collapse
Inverted gapps has black backgrounds so the screen bleeding is reduced
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
---------- Post added at 10:56 PM ---------- Previous post was at 10:51 PM ----------
I can drastically reduce screen brightness which helps, there's still some bleeding
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
dessolator666 said:
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
HermanV0929 said:
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
I'm sure it can be done... because you have to do pretty much exactly that when replacing the LCD or digitizer
Hey guys.
Today I found myself facing moisture inside my camera after giving the Z2 a small kitchen sink wash using only the water coming from the tap.
After an hour, when i went to take a picture, it was all foggy and to my surprise, the lens was completly obstructed by condensated water.
I read 1 fix on XDA and the rest of the internet -> return it, ask for a brand new one.
Well, if you are like me and don't usually take it for a bath or go into a pool (odd enough i had put it on the sink full of water for half an hour and nothing happened), there is a "fix" for it, which I got from common sense. What i mean by common sense is that if you heat water it evaporates, but since the camera is, i suppose, a bit isolated from the rest, you cannot just let the water go away on it's own, you have to give it some help.
So, what i did was: 1 - TURN OFF YOUR PHONE; 2- open both flaps; 3- Heat the phone with a hair dryer (i really mean heat it, so the watter does not return to liquid state imediatelly) 4 - Suck the moisture out from the left side (closest to the camera) flap with your mouth; 5 - WAIT FOR IT TO COOL BEFORE YOU TURN IT ON; 6 - go take a well deserved picture.
It goes away in a day at most anyway, it's simple science hot air hitting cold air = condensation, it's unavoidable
Mr.R™ said:
It goes away in a day at most anyway, it's simple science hot air hitting cold air = condensation, it's unavoidable
Click to expand...
Click to collapse
If the water is inside it does not come out in a day, the phone is sealed in.
Even if it did, this is an easy fix and gets rid of the water inside your phone, so your answer manages to add no value.
Nor does your so called fix
Code:
i had this on my xperia z1 after a day of been cinstantly damp and intermitantly soaked but my phone was hot from use. When i opened the ports it all cleared up within a minute
badjoras said:
3- Heat the phone with a hair dryer (i really mean heat it)
Click to expand...
Click to collapse
Your phone has a lot of expressly sensitive electrical components. I don't think it's advisable to heat it like this unless you want to fry components and loosen the glue that holds stuff together.
Sent from my D6503 using Tapatalk
Have the same few days ago. And did the same without hairdryer. First cold water from sink. After pass waterproof test i got phone with me to shower. After that i saw condesation inside. I almost died,one week old phone. But i open flaps, do everything without no.3, + sillica gel for 2 days , laying on the warm heater one night. Now everything is good, everything works, indicator under microsd flap is white. I think everthing is cool, what's yours opinion?
Just got the Problem
I just got this problem.
Before seeing this post I was so worried. Now, I'm feeling relaxed.
Thanks
same happened to me, just washing grease off phone using tab water. so does this only effect the glass on top of the camera? is the rest of the phone actually still waterproof? i'm a bit confused, so does this proof that our ip58 actually working or not? i never had this problem with my z1
Ah yes I remember that happening back when my Xperia Z initially died on me.
what would you guys recommend i do? repair it or just give up on it?
I have new phone, the old one wasn't waterproof. So if you can - repair i think.
thanksss ..
I've done so many ways to eliminate the moisture in my z3 lens .. with the rice , silica gel .. and it still kept coming back
but with your way , the moisture inside my phone immidiately gone and the way is logical as well ..
badjoras said:
So, what i did was: 1 - TURN OFF YOUR PHONE; 2- open both flaps; 3- Heat the phone with a hair dryer (i really mean heat it, so the watter does not return to liquid state imediatelly) 4 - Suck the moisture out from the left side (closest to the camera) flap with your mouth; 5 - WAIT FOR IT TO COOL BEFORE YOU TURN IT ON; 6 - go take a well deserved picture.
Click to expand...
Click to collapse
Thanks man your way worked with me
I had the same problem and fixed it. And a question remain that can I use my phone in water? My mind says no. Is there any way to get ? back?
badjoras said:
Hey guys.
Today I found myself facing moisture inside my camera after giving the Z2 a small kitchen sink wash using only the water coming from the tap.
After an hour, when i went to take a picture, it was all foggy and to my surprise, the lens was completly obstructed by condensated water.
I read 1 fix on XDA and the rest of the internet -> return it, ask for a brand new one.
Well, if you are like me and don't usually take it for a bath or go into a pool (odd enough i had put it on the sink full of water for half an hour and nothing happened), there is a "fix" for it, which I got from common sense. What i mean by common sense is that if you heat water it evaporates, but since the camera is, i suppose, a bit isolated from the rest, you cannot just let the water go away on it's own, you have to give it some help.
So, what i did was: 1 - TURN OFF YOUR PHONE; 2- open both flaps; 3- Heat the phone with a hair dryer (i really mean heat it, so the watter does not return to liquid state imediatelly) 4 - Suck the moisture out from the left side (closest to the camera) flap with your mouth; 5 - WAIT FOR IT TO COOL BEFORE YOU TURN IT ON; 6 - go take a well deserved picture.
Click to expand...
Click to collapse
I did the same thing only I used a vacuum cleaner instead of my mouth
For the common sense; the phone turns itself off if it reaches to almost 100°C. If a passively cooled CPU is allowed to reach that high it means the back cover which is supposed to handle both the heat of the SoC and the battery, is also safe against temperatures that human skin can not.
I believe hair drier makers are also aware of human skin's sensitivity to heat, and design their products according to that.
So using a hair drier to a mobile device not more than you use it on your hair, which is generally wet with the risk of over heating, from the same distance should make no harm on the device.
Sent from my D6503 using XDA Free mobile app
I used my table lamp to heat the water.
Thank you badjoras, it works for my z3 that I have left at the bottom of the pool for 5 minutes. The condensation occured even after the phone has successfully passed the pressure (barometer) test before swimming. I used heat gun from a safe distance (30-40 cm) for a few seconds before sucking the air using my mouth, and repeated the procedure for three or four times before all the water disappeared.
Hi Everyone,
So I was on holiday with my beloved Ultra, and using it in the pool. Cool thing is, this phone is waterproof! That's what I thought until I got on the plane a few hours later and upon trying to use my phablet the touch screen stopped responding. It seemed to function OK, I just couldn't unlock it or use it as there was some kind of hyperactive spectre flying around inside making it seem like the touchscreen was possessed. I looked a little closer, and not only was there condensation visible in both camera lenses, but upon opening the usb cover there was also moisture inside there. I opened the other side, and the moisture indicator was still white, so I think the problem was specifically with the usb port cover.
Anyway, it's not covered under any kind of warranty as I bought it overseas, and I have taken it to a repair shop who confirmed that it's water damaged and that they would need to fix the damaged USB port and replace the screen to make it work again. I just want to buy a new one as it would be cheaper than getting it fixed, but I have some data/apps on the old one I don't want to lose. Any suggestions on the best approach? If the shop can read the eMMC and back it up, could I use that to restore data/apps onto a new phone, or am I better off just getting it fixed...
Advice/opinions appreciated.
it's a marketing trick. they are not actually waterproof.
I guess this guy's luck was bad. Mine had contact with water a couple of times and thankfully it lived upto its waterproofness promise
Sent from my C6802 using XDA Premium 4 mobile app
tsiros said:
it's a marketing trick. they are not actually waterproof.
Click to expand...
Click to collapse
This is a stupid reply. I brought it with me in the pool with my kids, made photos and videos underwater (touch block + volume rocker), no problems at all.
Same goes with my wife's Z.
Of course, if you go swimming with the USB flap open, well, you're an idiot. (Not that I accuse OP of being one, just that 80% of the time when I saw someone with a faulty phone/laptop/tablet it was not working because of THEM).
Sent from my C6833 using Tapatalk
Hopefully someone replies with some advice that is actually helpful... FYI I have used it in the pool (and had it underwater) multiple times before without problems. I always make sure the seals are sitting properly when I close them so I am doubtful it was user error...
The usb port is fully brpken?
I think it's corroded, but definitey doesn't work.
choasty said:
I think it's corroded, but definitey doesn't work.
Click to expand...
Click to collapse
without usb and screen it will be difficult for you to get data off yourself.
fastest83 said:
This is a stupid reply. I brought it with me in the pool with my kids, made photos and videos underwater (touch block + volume rocker), no problems at all.
Same goes with my wife's Z.
Of course, if you go swimming with the USB flap open, well, you're an idiot. (Not that I accuse OP of being one, just that 80% of the time when I saw someone with a faulty phone/laptop/tablet it was not working because of THEM).
Sent from my C6833 using Tapatalk
Click to expand...
Click to collapse
good for you, you were lucky. on the xperia forums and on here, there are many MANY people who had their phones damaged from water. Are ALL of them at fault?
however, call sony and ask them (i did):
1) what *guarantee* is there that with the flaps closed the phone will not receive water damage? they will answer none. There is no case where the warranty will cover water damage. Whether it's your fault or the phone's fault, it is irrelevant to sony. they will NOT cover it.
2) what happens if, after *normal use*... notice this: *normal use*, NOT abuse, the flaps lose their sealing ability? Does the warranty cover it? No. Warranty does NOT cover "normal use wear". Which means the flaps WILL lose their sealing ability and you end up with a non-waterproof phone. How soon? NOONE KNOWS because there is no way to actually TEST it, at least not as a USER. You MIGHT be able to have it tested at sony... but that would mean testing it every. single. time. you close any of the flaps...
your phone, at any given point, MAY or MAY NOT be waterproof. However, since you have no way to test it, it means that you CAN NOT TRUST it to be waterproof, which is, of course, means you have to treat it as NOT waterproof.
which, in the end, means the phone is not waterproof.
as a sidenote, keep any and all profanities to yourself
Blah blah. The phone is waterproof. No need to be all technical and stuff. Can it be used in water for a certain period of time? Yes.
Your post reminds me of when ships were first being built. If a boat ends up sinking from wear and tear does that mean it wasn't a floating device? Also wear and tear....that's why we check our cars at a set time for periodic maintenance because of wear and tear.
I got lax with mine and took it in the shower and got water in it, USB flap is worn. Not the companies, because I didn't take the necessary steps to make sure my phone was periodically maintained.
Just my 2 cents...
Just a quick question. Anyone else have an issue with their screen cracking? My P9000 has developed a crack over the led. I didn't drop, knock or bump the phone. I've emailed support for advice. I'll keep this forum posted.
Update got a very prompt response. Two sentences
"Good day!
we are sorry to hear that, but screen will not crack by itself. it may have some physical damage on it."
No details of how to get a repair, that's it! Not the best customer service. I've replied enquiring about service centres, costs etc. and will update the post when I get more info. There are a few posts asking for similar details re. Screen replacement so the info will be useful for the community.
actually it's strange to think that a screen can brake by itself , can you post some pictures?
elephone customer care have already proved it's lower quality service . i don't know where you live but best solution imho is to give the phone to a local cinese phone repair shoop , here in my city there are a couple that repair - fix phones for low money and they also provide spareparts that arrive very quick and at low price thanks to it's black market channel, try to search one
I agree it's very unusual that the screen would break in this way, but I'm really very careful with all my devices and this has never happened before.
If Elephone say that this cannot happen then I'm not going to quibble, I'm more interested in repairing the phone. Sending it back to the seller for repair will be an interesting, long and probably prohibitively expensive process, but I'll make enquiries.
In other news Elephone are still working on a new ROM for the device, I took the opportunity to ask supplementary questions in my email :laugh: so the chatter on the forums about the 19/04 build being the last one can abate for a while.
The crack in question. Doesn't impair functionality and there's are no signs of impact
The only replacement display I found on the Web is this one https://m.aliexpress.com/item/32673463140.html Unfortunately I have no clue if this is an original display and if could place it on my phone by myself
Your phones has physical damage along the bottom side of the metal frame can clearly see where its been scraped. You sure it didn't drop or get dragged along something while face down? Hopefully there's an OEM replacement as its just the glass that seems to be damaged not the LCD
Thanks I wouldn't know how to even begin the repair but it's useful info.
I had a similar small crack appear on mine which had not been dropped I assumed it had been knocked whilst in my pocket, But then today i put my phone in my pocket to drive and collect the kids when i got to the school i had 3 additional cracks I assume its something to do with the size of the screen and it not flexing.
The new cracks now make it pretty tough to use the phone as they are affecting the touch functions, once i can unlock it i will take some photos to post.
Banathe said:
I had a similar small crack appear on mine which had not been dropped I assumed it had been knocked whilst in my pocket, But then today i put my phone in my pocket to drive and collect the kids when i got to the school i had 3 additional cracks I assume its something to do with the size of the screen and it not flexing.
The new cracks now make it pretty tough to use the phone as they are affecting the touch functions, once i can unlock it i will take some photos to post.
Click to expand...
Click to collapse
Thank you. I'd almost convinced myself that I must have knocked the phone.
Events have taken a new turn. The left hand side of the screen now creaks and pops when you press on it. If I press sufficiently hard enough it stops creaking and popping, almost as if it is correctly seated again only to literally and audibly pop out again 5 minutes later.
I will post a video later, and will be contacting elephone with evidence that there is a design flaw with the device. I'll keep this forum updated on my progress.
thats weird thats where my spontaneous crack started images attached, the bottom one is under the glass but i think was the cause of the left side one.
Adding images as attachments as well given the URLS don't seam to be showing correctly.
Mine also has a minor crack on the screen, it's in a case and has not been dropped. There is no damage to the frame at all, I'm guessing it's from being in my pocket. The phone obviously isn't as strong as mainstream manufacturers. My crack is very faint in the top right corner and you really have to look at it in a certain light to see it.
If it gets worse, I'll buy a new phone (One Plus 3) and not look at this device again
Sent from my P9000 using Tapatalk
Mine broke in my front pocket without impact. It was the aluminium frame that was bending and must have cracked under the stress. In hindsight I should have started putting the phone in my pocket the other way around. Ha ha!
YorkshiresSnipper said:
Mine broke in my front pocket without impact. It was the aluminium frame that was bending and must have cracked under the stress. In hindsight I should have started putting the phone in my pocket the other way around. Ha ha!
Click to expand...
Click to collapse
I note the replacement screens have come down in price I may have to have a go at a repair.
Sent from my Z2 Plus using Tapatalk
Everyone Participate Please
I'm about to buy this phone so just wanted to make sure if anyone had issues with waterproofing or water test fails like previous Xperia phones.
Please give me your experience with this device in wet conditions
So far I have found the Z5C has way better waterproofing than the z3c, as you are not needing to move the flap to charge the phone all the time
I have used my phone in the ocean (even though it is not specifically designed to be used in the ocean) and washed it off with fresh water afterwards multiple times, and it works like a charn, no leaks or condensation
@nzzane
Great to hear!
Headphones and sound issues till dries
Also, a kind of obvious note. You will have to wait till the phone dries to charge it, and sound quality will be a bit muffled due to the water (until it dries)
@smardu @nzzane
I can live with that
ill recommend to put duct tape on the string hole
i found on my test water can enter from there only
@Superrman
Are the string hole and flaps connected like open tunnel between them (considered faulty units)?
showers, rinses(not washing machine, just tap or hose), thunderstorms A+ for this phone so far!
Sound does get muffled in direct spray and the occasional water drop changes the song lol but all in all had the phone for a year and could sell it as NEW if needed
@Tingles
I guess Sony waterproof smartphones are getting better and better!
rip
I ran mine under a tap and five minutes later the screen stopped working lol.
avionisasian said:
I ran mine under a tap and five minutes later the screen stopped working lol.
Click to expand...
Click to collapse
Were you able to fix it?
Waterproof??
Yea so I got my z5c back from repair and somehow I damaged the screen with water when running it under a tap. So I guess mine wasn't that waterproof...
avionisasian said:
Yea so I got my z5c back from repair and somehow I damaged the screen with water when running it under a tap. So I guess mine wasn't that waterproof...
Click to expand...
Click to collapse
Our device has these ratings
IP6X. Dust tight.
IPX5. Protected against low-pressure water jet spray for at least 3 minutes.
IPX8. Protected against the effects of continued immersion in water at depths greater than 1 metre. The exact conditions are specified for each device by the manufacturer.
Here's the address for proper precautions for our device, plus some other info.
http://support.sonymobile.com/global-en/dm/waterproof/
Although now that you have had it repaired I would be a little more delicate with that device.:fingers-crossed:
When your phone gets opened, generally consider it to lose its water proofness. However I have been able multiple times using hot glue to perfectly seal it again.
Remember there's an easy and reliable way to check if your Xperia is water proof: Xperia Water Resistance Test