As the title says.
I downloaded the correct tar file from the TWRP site, and successfully installed using Odin.
However, attempting to reboot it just bootloops. I tried the install again, no change. Booted into (TWRP) recovery which looks fine, and cleared cache. Still bootloops. Did a full wipe. Still bootloops.
Smart Switch recognised the phone in download mode but won't accept the S/N from the back cover - I can't get it to show in download mode as mentioned in other threads.
I'm downloading stock firmware but it's slooooow. Any suggestions? What went wrong?
parapaul said:
As the title says.
I downloaded the correct tar file from the TWRP site, and successfully installed using Odin.
However, attempting to reboot it just bootloops. I tried the install again, no change. Booted into (TWRP) recovery which looks fine, and cleared cache. Still bootloops. Did a full wipe. Still bootloops.
Smart Switch recognised the phone in download mode but won't accept the S/N from the back cover - I can't get it to show in download mode as mentioned in other threads.
I'm downloading stock firmware but it's slooooow. Any suggestions? What went wrong?
Click to expand...
Click to collapse
First Of all If u want Twrp To work on S6 edge Flash Cf Autoroot before flashing Twrp
Secound Is Ur device refurbished or something or u r putting ur s/n number wrong
Related
I have a rooted GT 10.1 LTE with the EH04 update. I have tried flashing via CWM which results in the obvious breakage. I have also tried installing via Recovery and Odin with the attached files and in various combinations with no luck.
Any suggestions or ideas on what I am mucking up to not be able to get CWM only my tablet?
To note: It was working prior to the EH04 update.
Bump.
Any ideas?
try the cwm here:
http://forum.xda-developers.com/showthread.php?t=1090289
to a certain degree it is a lot of trial and error as to what parts of the various 10.1 models are common and which are distinct -- at this juncture what is to loose from flashing a different cwm?
Try this recovery ( flash zip)
http://www.mediafire.com/?w45j8i0fcj0wck0
Then try this rom
http://forum.xda-developers.com/showthread.php?t=1277045
Its been working very well for me.
Mr.Jester said:
I have a rooted GT 10.1 LTE with the EH04 update. I have tried flashing via CWM which results in the obvious breakage. I have also tried installing via Recovery and Odin with the attached files and in various combinations with no luck.
Any suggestions or ideas on what I am mucking up to not be able to get CWM only my tablet?
To note: It was working prior to the EH04 update.
Click to expand...
Click to collapse
I unrooted to get the EH04 updated using this: http://rootzwiki.com/topic/7718-romleakodineg01-factory-stock-odin-image-vzw-lte-tab-101/ , waited for the EH04 update, then re-rooted using this (which I used to root initially): http://rootzwiki.com/topic/2242-root-recovery-galaxy-tab-101-lte/ .
Perhaps you should unroot per the above, take the update, then re-root as above--worked for me.
i ota'd EH04, lost root. downloaded kernel.zip, applied it, got root back, installed cwmod, clicked to reboot into recovery and it's looping since, i can't do anything but get into ODIN but the PC wont recognize it, although i get a pop up saying android.. installed, adb devices doesn't pick up either. can't get into recovery.
---
update
http://forum.xda-developers.com/showpost.php?p=18121666&postcount=53
someone warned in the forums and i didn't read it before i did it, used odin to put recovery.zip, now i'm back in action.
The recovery you provided is the same that I attached. What I discovered however is that if I booted into recovery right after installing the CWM recovery, CWM would load. If I booted into stock EH04 then back into recovery, the stock recovery would load. It seems as if the ROM was restoring stock recovery when it loaded. After installing Lightspeed, CWM recovery stayed in place.
Either way, thank you for the assistance. I hope this thread ends up helping someone else.
My steps to install Lightspeed from Stock ROM EH04:
1. reboot recovery, install either recovery.zips above.
2. When the system automatically reboots, hold volume up to boot into recovery again. This time it should be CWM.
3. Wipe cache and factory reset
4. Install Lightspeed ROM
I
Mr.Jester said:
The recovery you provided is the same that I attached. What I discovered however is that if I booted into recovery right after installing the CWM recovery, CWM would load. If I booted into stock EH04 then back into recovery, the stock recovery would load. It seems as if the ROM was restoring stock recovery when it loaded. After installing Lightspeed, CWM recovery stayed in place.
Either way, thank you for the assistance. I hope this thread ends up helping someone else.
My steps to install Lightspeed from Stock ROM EH04:
1. reboot recovery, install either recovery.zips above.
2. When the system automatically reboots, hold volume up to boot into recovery again. This time it should be CWM.
3. Wipe cache and factory reset
4. Install Lightspeed ROM
Click to expand...
Click to collapse
Thank you. Everytime I tried flashing cwm recovery, I would always end up back at stock recovery. Your fix worked perfect.
Hi I have rooted my UK i9100 with odin and successfully installed resurrection remix previously. When trying to flash an updated version I stupidly forgot to factory wipe and now my phone wont boot, it gets stuck on the rom boot screen and i cant get into cwm.
I can get into download mode and from there have tried flashing another rom via odin (litening rom) to see if that would boot to get me into cwm but that freezes on the boot screen also. I tried to use Galaxys2recovery as shown on zedomax youtube channel but then realised that is done from gingerbread only. I tried reflashing "CF-Root-SGS2_XX_OXX_LP6-v5.2-CWM5" via odin and then the litening rom again but that still hangs when trying to boot.
Is there something obvious I should be doing? ..I am (unsuprisingly) a noob
Thank you
you could have asked at the first time itself, before various yourown attempts ?
if you are able to get CWM now, try to install the ROM after data factory reset and all the wipes + system format from Mounts & storage.
if it didnt help again go to CWM do all the wipes and format system, and switch off and get into the download mod and flash a GB stock rom from ODIN
I can get into download mode and from there have tried flashing another rom via odin (litening rom) to see if that would boot to get me into cwm but that freezes on the boot screen also
Click to expand...
Click to collapse
odin if for stock roms not custom roms / .zip files....
zaheedahmed said:
if it didnt help again go to CWM
Click to expand...
Click to collapse
that's the thing, i cant get into cwm, or at least i don't know how to. Is there a file I can install from odin that will put me straight into cwm without having a working rom?
why do you wait to boot the phone to get into the CWM,
didnt you try Vol-up+Home+Power while phone is off
Hi Everyone! just a rookie here in need of a bit of advice.
I'm a Galaxy S II I9100 owner and have my phone rooted and all setup with custom roms and been comfortable with flashing for some time now. My ROM of choice recently was Vanilla Rootbox and have to say the ROM has been fantastic with very few bugs to report. Last night i recieved the OTA update via Goo Manager for Vanilla Rootbox 3.4. I downloaded the full update over wifi and flashed with all wipes no worries. Next step was to flash the latest GAPPS and i figured there would be nothing wrong with flashing the GAPPS zip i had on my sd card that i had downloaded the last time i was notified of a GAPPS update via Goo manager as well. After flashing, wiping everything and rebooting again. My phone then booted up to a series of dialog boxes indicating that many google processes had stopped functioning. apps.google.com etc etc. A similar error has been reported in the Vanilla Rootbox thread by another user but i wasnt able to report this bug their either because my post count is too low to post in a development forum. So after seeing this error i rebooted into recovery to flash my last backup but CWM recovery came back with an error messaging stating it couldnt mount either ext or int sdcard. i did a factory reset which made no difference to the problem whatsoever. I then downloaded ODIN and the latest stock ICS Rom and flashed it via ODIN with no reported errors. My phone now boots through the optus boot animation and is stuck at the Galaxy S 2 screen with the flashing red and yellow animation over the S. If i turn off the phone with the power button, the phone turns off and immediately starts again and gets stuck at the flashing s screen. I've taken the battery sim and ext sd card out and put it all back in only for the problem to persist.
If anyone could help me there's a donation and my thanks in it!
Much appreciated
Nick
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
gastonw said:
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
Click to expand...
Click to collapse
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
darkstar117 said:
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
Click to expand...
Click to collapse
wow wow, leave pit files alone for now, they are nasty.
What stock ROM did you flash? 4.0.4 or 4.0.3?
You can factory reset via recovery mode.
Try installing kies anyway, it can't never hurt. Just make sure all applications are closed before you re-flash.
here's jb leak, might help:
http://www.sammobile.com/2012/11/15/i9100xxlsj-%E2%80%93-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
darkstar117 said:
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
Click to expand...
Click to collapse
Tell me your:
Model
Firmware
Country
Carrier
Always mention this
try flashing jb leak (ROM, modem & kernel package).
While I did find a similar posts, they were for different devices. I also tryed to search o different sites for similar problems to no avial.
What Happened: After backing up system data and app data then removing Foxhound ROM with factory reset, and installing UltimaROM i came to find that the modem did not install correctly result in no connection to my cell network. I booted into TWRP recovery to try and do a re-install of the ROM only to find that TWRP was restarting itself every 3 seconds or so. I attempted to restart the device which i found to result in a TWRP bootloop that i cannot get out of, it constantly is booting into recovery mode and i cannot get it restart the OS.
What I've tried: Since i can get into download mode i decided to attempt to re-install TWRP using Samsung Galaxy S3 Toolkit but since i do not have USB debugging on i cannot do that. I'm mainly looking for a fix before i go and claim it on the warranty saying update went bad or something. If people need more information I will try to provide it as best i can.
Summery if i confused people is that TWRP is in a bootloop, i am unable to get to the OS, but i still have download mode available.
I fixed it but not how I would have liked to. I ended up losing all data due to flashing stock ROM using ODIN. I would still much appreciate a alternative method that does not involve loss of data though just for future reference, that is if anyone knows a alternative method.
Sent from my GT-I9300 using xda app-developers app
could've tried reflashing TWRP or any other recovery through odin
I have an LG Optimus Q (LGL55c) with twrp loop. I was trying to go back to stock rom, instead I deleted all the system files in twrp when it was working...Then I rebooted back into recovery and get the loop. Does this mean I completely bricked my phone? I tried using adb, adb shell doesn't work. It does find the device. Even tried the LG update with no sucess Any ideas or suggestions?
I just read the forum title, I thought this was for the Optimus Q not the Samsung S3. Sorry mods
Temasek unofficial cm12 5.02
I was running this rom when my power button shorted and I got it replaced but then I tried to do a complete wipe and clean flash but since then it has been twrp bootlooping, tried to flash the latest recovery through Odin but still doesn't work also tried stock firmware flash but says binary not available.
This is my secondary device and I've not been in touch with Odin for a while. Any help will be appreciated.
Thanks
Download latest firnware from sammobile.com and flash it with Odin, as described on sammobile: does Odin finish with '1 succeeded'?
I'm in a very similar situation, but with my Samsung Galaxy Note 2 (N7105). It's rooted, and I am, or was using TWRP 2.7.0.2. ROM is CyanogenMod 12, 5.0.2 Lollipop.
I did a factory reset from INSIDE Android, and chose to wipe internal memory. Phone did the reset and wipe, rebooted into TWRP instead of Android, and now I have TWRP boot loop.
I posted more about it here: http://forum.xda-developers.com/showpost.php?p=60247503&postcount=3671
I have the Problem toooo!
What must i do Now!
with my S3 is the same!!!
For posterity:
With an old (2014?) version of TWRP and a custom ROM, I tried reverting to factory settings. That caused the phone to reboot TWRP, and the screen would flash every couple of seconds. I flashed a stock recovery image I found on Google, and when it restarted again, the wipe was completed successfully. My intention was to wipe all user data anyways so I can't say if this method might save it.
im on stock root and i wanted to hopefully flash a rom, but first i needed a custom recovery. On my phone, i downloaded Rom manager and it asked me to install cwm. it found my device and it downloaded and said installed successfully. i rebooted into recovery and from there it loops and boots into recovery non stop. i remove the battery and put it back in and it still tries to boot into recovery with the loop. (Semi-fix) when i remove my battery and boot into download mode. i can cancel it and it will skip trying to boot into recovery and load just fine. i can then shut down or restart as needed. but booting back into recovery will start the issue over again. i just want to know a safe way to have cwm on my note 3, or how to revert it back to normal. any help please?
scarface195894 said:
im on stock root and i wanted to hopefully flash a rom, but first i needed a custom recovery. On my phone, i downloaded Rom manager and it asked me to install cwm. it found my device and it downloaded and said installed successfully. i rebooted into recovery and from there it loops and boots into recovery non stop. i remove the battery and put it back in and it still tries to boot into recovery with the loop. (Semi-fix) when i remove my battery and boot into download mode. i can cancel it and it will skip trying to boot into recovery and load just fine. i can then shut down or restart as needed. but booting back into recovery will start the issue over again. i just want to know a safe way to have cwm on my note 3, or how to revert it back to normal. any help please?
Click to expand...
Click to collapse
Pull battery let it sit for two minutes. Push menu button, volume down button, and power button at the same time boot into download mode. once there flash a fresh copy of your OS which ever version of KitKat your running. You lose all your personal data, but your beyond that now. Then here is link to my thread should answer all your questions http://forum.xda-developers.com/note-3-sprint/general/samsung-note-3-rom-flashin-basics-t2896440 enjoy !!!
uknow said:
Yeah ive said it a few times this should not be used
If youve bricked your phone you can get back into your phone by holding volume down menu botton and power botton at the same time when it pops up the warning screen to enter download mode hit cancel your phone will then boot up after your phone is on if you do not have a computer the way you fix the phone so you dont have to do this every time your phone is off you need mobile odin and a kitkat cwm.img.tar for our phone flash it and problem solved you can now boot into cwm recovery then if you want you can flash a twrp img zip through cwm or just keep cwm hope this helps
Ps if you Google mobile odin the dev gives it away on his xda mobile odin page
Click to expand...
Click to collapse
.............^^^^^^...........
stuck in recovery loop also
hi i am new to all this..i managed to get my sprint note 3 4.4.4 NK4 rooted and i read that i also needed a custom recovery so i used odin to install "philz_touch_6.08.7-hltespr.tar.md5" and it said success but when i tried to get into it it just says recovery is not seandroid enforcing i also used rom manager to get into it automatically but it just keeps looping saying same thing. is there a way out of this mess?
update-- i found an updated version of the philz tar file and installed it with odin and that got me out of the loop..just havent tried to get back into recovery yet...lol
Cat1970 said:
hi i am new to all this..i managed to get my sprint note 3 4.4.4 NK4 rooted and i read that i also needed a custom recovery so i used odin to install "philz_touch_6.08.7-hltespr.tar.md5" and it said success but when i tried to get into it it just says recovery is not seandroid enforcing i also used rom manager to get into it automatically but it just keeps looping saying same thing. is there a way out of this mess?
Click to expand...
Click to collapse
First, pull the battery for a minute then reinstall hold the power, menu, and volume down buttons at the same time and boot into download mode. The version of Phil'z CWM you flashed is to old for 4.4.4 NK4. Now download to your desktop the right Philz CWM recovery file (Phil'z_Touch_6.48.4-hlte.tar.md5 ) here is the link https://goo.im/devs/philz_touch/CWM_Advanced_Edition/hlte/ there are two listed use the second one. Flash with odin and you should be good to go. Go to my thread http://forum.xda-developers.com/note-3-sprint/general/samsung-note-3-rom-flashin-basics-t2896440 for more info.
done exactly as you said and the same screen came up saying recovery is not seandroid enforcing and then it jumps to Philz Touch 6 so im assuming everything is right now...i really appreciate the help! tyvm
different rom
ok..i installed cyanogen rom..i also used titanium backup..i want to go back to where i was but i dont see titanium backup on there anymore..how do i revert back?
i guess i need to update my phone n900p (help)
my rooted note 3 was running 5.0 L so i tried flashing a custom recovery both TWR and CWM now its stuck in boot loop. i read all the post showing you how to get out the bootloop. how ever i still need to put a recovery on my phone are there any updated links for this with odin because i was using the odin 3.0 sorry odin 307