This is a Backup of the PH1 ROM's system and modem partitions. This is a Pre-Rooted ROM with the SD Card write permissions fix. This is different from my other post in those two differences.
You will need a custom recovery to install this ROM. (http://forum.xda-developers.com/note...lipop-t3089382)
Always perform the appropriate backups and other steps just in case something messes up. If you are on Lollipop, you should be able to just flash and go without any data loss (except custom system apps), but no promises.
Extract the folder (ES File Explorer or 7 Zipper) to "extsdcard/TWRP/backups/[serial number]" then boot into recovery and restore the image. The easiest way to get this folder is to simply perform a backup first, then unzip this folder next to the one for the backup you just created.
I didn't factory reset prior to this backup because it's just system partitions, so let me know if there's anything weird.
https://drive.google.com/open?id=0B2iEgzRTFjrQa2JEbE1DSE9qNHM
Here's the Odin ROM:
http://forum.xda-developers.com/note-3-sprint/general/rom-odin-ph1-update-t3463178/page1
Here's my non-rooted TWRP ROM:
http://forum.xda-developers.com/not...stom-recovery-rom-stock-rooted-t3449321/page1
Still 5.0 this is probably just a security update
RDF
http://device.sprintpcs.com/Samsung/SM-N900P-SPRINT/PH1.rdf
evilvoice said:
Still 5.0 this is probably just a security update
RDF
http://device.sprintpcs.com/Samsung/SM-N900P-SPRINT/PH1.rdf
Click to expand...
Click to collapse
Yep, just a security update most likely. Looks like some of the stock (Sprint) apps may have been updated as well . The update file was only about 190 megabytes if I remember correctly.
Quick question on updating modem & firmware.. I'm stock rooted ok2, and i dont have this update yet. I am working toward flashing the newly released and highly anticipated DL Modded N5N7 v4 which requires the PH1 updated firmware.
Do I need to ODIN flash the update files from the other PHI ROM thread or can I just do a full wipe and flash this backup with TWRP?
Thanks in advance.
Sent from my SM-N900P using XDA Labs
MeAtKeRtN said:
Quick question on updating modem & firmware.. I'm stock rooted ok2, and i dont have this update yet. I am working toward flashing the newly released and highly anticipated DL Modded N5N7 v4 which requires the PH1 updated firmware.
Do I need to ODIN flash the update files from the other PHI ROM thread or can I just do a full wipe and flash this backup with TWRP?
Thanks in advance.
Sent from my SM-N900P using XDA Labs
Click to expand...
Click to collapse
You can just flash the rom you want and keep your current bootloader/modem. But it's always suggested to keep current with any bootloader/modem, that the OP mentioned. That way if there is a issue with the install, it wouldn't be that.
Sent from my Nexus s using XDA-Developers mobile app
jhunt75 said:
You can just flash the rom you want and keep your current bootloader/modem. But it's always suggested to keep current with any bootloader/modem, that the OP mentioned. That way if there is a issue with the install, it wouldn't be that.
Sent from my Nexus s using XDA-Developers mobile app
Click to expand...
Click to collapse
The preferable answer would have been 'NO' or 'I'M NOT SURE' as a direct answer to my very specific question... as I now have a phone that doesn't make phone calls.
MeAtKeRtN said:
The preferable answer would have been 'NO' or 'I'M NOT SURE' as a direct answer to my very specific question... as I now have a phone that doesn't make phone calls.
Click to expand...
Click to collapse
Hey, I've seen you in a few threads and figured I ask before I made the same mistake. I'm looking to upgrade to DL Modded N5N7 v4 like yourself. I have a exploding Note 7 still and I'm anticipating being blacklisted at some point. As crazy as it sounds I like my Note 3's snappiness and everything else over the 7. My issue is my Note 7 radio gets 4g in my job and my Note 3 radio is 3g or spotty. I'm sure my modem and baseband is outdated and may help being updated
I'm on a older Moars Rom Baseband Nk4 android version 4.4.2. Did you figure out where things went bad. I was thinking of following these instructions http://forum.xda-developers.com/note-3-sprint/general/rom-odin-ph1-update-t3463178 don't want to mess this up.
What did you use and what should you have used?
Thanks
Lyvewire said:
Hey, I've seen you in a few threads and figured I ask before I made the same mistake. I'm looking to upgrade to DL Modded N5N7 v4 like yourself. I have a exploding Note 7 still and I'm anticipating being blacklisted at some point. As crazy as it sounds I like my Note 3's snappiness and everything else over the 7. My issue is my Note 7 radio gets 4g in my job and my Note 3 radio is 3g or spotty. I'm sure my modem and baseband is outdated and may help being updated
I'm on a older Moars Rom Baseband Nk4 android version 4.4.2. Did you figure out where things went bad. I was thinking of following these instructions http://forum.xda-developers.com/note-3-sprint/general/rom-odin-ph1-update-t3463178 don't want to mess this up.
What did you use and what should you have used?
Thanks
Click to expand...
Click to collapse
My mistake was following bad advice and flashing the TWRP Backup of PH1 in the OP of this thread instead of ODIN flashing the full ROM-ODIN-PH1- Update- t3463178.
I was able to get TWRP to restore my backup to OK2. From there I did a full wipe 3x and ODIN flashed the full PH1 update, immediately rooted with CFautoroot and reinstalled TWRP 2.8.7.0.
From there I followed the OP instructions in the DL Modded N5N7 thread which require the ROM, Kernel Cleaner, MVNO Buzbee2, Sprint VVM, and I installed the DL MM UIX Kernel.
The ROM and kernel are both really well put together except my mobile network connection to Sprint has been intermittent... the phone was stuck roaming and was connecting in spurts with Verizon, sprint, or the network was unavailable.
I just dirty flashed the Rom, Kernel, and MVNO fix an hour or so ago and the APNs seem to be sticking now. We'll see.
I have three Note 3's and each has its own quirky 'personality'- not especially playing nicely with most of the Port ROMs available these days. Hope this answers your questions and helps someone else trying to keep their Note 3 thriving.
MeAtKeRtN said:
The preferable answer would have been 'NO' or 'I'M NOT SURE' as a direct answer to my very specific question... as I now have a phone that doesn't make phone calls.
Click to expand...
Click to collapse
I am not trying to start any trouble, but from reading your comment it seems you are suggesting I gave you bad or wrong advice. So I want to explain myself just in case it was a misunderstanding. All roms are capable of being flashed with older bootloaders and modems. But the proper thing to do, is to always be up to date with all bootloader/modem files. This way you will not run into any problems. Now I didn't mention anything about flashing the OP'S twrp backup method. I figured you may have been experienced enough to flash these BL/modem files from a source like sammobile. Then proceed to flash your rom of choice. As you experienced you lost your signal. It may have been a few reasons why this happen. 1. The way the OP mentioned to flash wasn't meant for your phone. Every phone response differently. 2. The rom for whatever reason can only be used if you dirty flashed over your current system. This will not be the only time you may have to do it this way. So instead of being sarcastic with your reply, maybe try and ask the one who is helping you to explain themselves more. We are all here to help each other, and by no means was my response to your question was meant to harm your phone.
Sent from my SM-N920C using XDA-Developers mobile app
jhunt75 said:
I am not trying to start any trouble, but from reading your comment it seems you are suggesting I gave you bad or wrong advice. So I want to explain myself just in case it was a misunderstanding. All roms are capable of being flashed with older bootloaders and modems. But the proper thing to do, is to always be up to date with all bootloader/modem files. This way you will not run into any problems. Now I didn't mention anything about flashing the OP'S twrp backup method. I figured you may have been experienced enough to flash these BL/modem files from a source like sammobile. Then proceed to flash your rom of choice. As you experienced you lost your signal. It may have been a few reasons why this happen. 1. The way the OP mentioned to flash wasn't meant for your phone. Every phone response differently. 2. The rom for whatever reason can only be used if you dirty flashed over your current system. This will not be the only time you may have to do it this way. So instead of being sarcastic with your reply, maybe try and ask the one who is helping you to explain themselves more. We are all here to help each other, and by no means was my response to your question was meant to harm your phone.
Click to expand...
Click to collapse
No misunderstanding here... I asked a specific either/or question directly related to the thread topic (twrp custom recovery version) and you either misunderstood my question or decided it required an answer other than a 'yes or no' As a result of your longwinded answer, I lost several hours working through how to get a signal back on my phone. Was pretty annoying.
MeAtKeRtN said:
No misunderstanding here... I asked a specific either/or question directly related to the thread topic (twrp custom recovery version) and you either misunderstood my question or decided it required an answer other than a 'yes or no' As a result of your longwinded answer, I lost several hours working through how to get a signal back on my phone. Was pretty annoying.
Click to expand...
Click to collapse
I never knew giving someone detailed information was a problem. It's funny how I never had an issue with the install, but you did. It seems you lack enough experience to realize a few things. But I will make it a point to never help you again. Whether that's to long-winded or not for you, oh well.
Sent from my SM-N920S using XDA-Developers mobile app
MeAtKeRtN said:
No misunderstanding here... I asked a specific either/or question directly related to the thread topic (twrp custom recovery version) and you either misunderstood my question or decided it required an answer other than a 'yes or no' As a result of your longwinded answer, I lost several hours working through how to get a signal back on my phone. Was pretty annoying.
Click to expand...
Click to collapse
Did you get it all figured out?
I did get it figured out. Wasn't much more than an unnecessary inconvenience that someone else might be able to avoid.
Ok, so something weird...
Im running KK4.4.2 with the NC5 baseband on Sprint.
I upgraded my TWRP to 2.780 to flash the recovery both first time 'dirty flashing' and the 2nd time doing a facory wipe.
I removed the battery after the flash.
When I reboot, the phone stays on the Yellow Sprint screen and the LED pusles blue slowly. So far been doing it for 15 mintues.
What am I missing?
Dave
Unidave199 said:
Ok, so something weird...
Im running KK4.4.2 with the NC5 baseband on Sprint.
I upgraded my TWRP to 2.780 to flash the recovery both first time 'dirty flashing' and the 2nd time doing a facory wipe.
I removed the battery after the flash.
When I reboot, the phone stays on the Yellow Sprint screen and the LED pusles blue slowly. So far been doing it for 15 mintues.
What am I missing?
Dave
Click to expand...
Click to collapse
Give it 30 minutes? It seriously takes a long time. Are you sure you want to upgrade to lollipop? In just asking because you've been on Kit Kat long after support for lollipop or this phone has long stopped. I'd suggest downloading the latest Odin and flashing that instead, unless there is something here you wanted? I'm rooted on PL1 and have no issues other than my phone being as old as it is and how many times it's been flashed.
evilvoice said:
Give it 30 minutes? It seriously takes a long time. Are you sure you want to upgrade to lollipop? In just asking because you've been on Kit Kat long after support for lollipop or this phone has long stopped. I'd suggest downloading the latest Odin and flashing that instead, unless there is something here you wanted? I'm rooted on PL1 and have no issues other than my phone being as old as it is and how many times it's been flashed.
Click to expand...
Click to collapse
30 minutes? Woah that is a long time. Ok I will give it a try sometime when I go to bed.
I am mainly trying to get the PL1 update and not mess with Odin if I can get around it. I would like to try and port the Darklord Marshmellow ROM and take advantage of built in google assistant
So I thought I would try them. And always get back if I need to but wanted to keep the PL1 modem updates.
I only have one problem with one other phone user... She doesnt always get my texts and I dont always get hers. I dont know if others arent getting them and just dont know but my 1 friend I text a lot so she notices when there is a gap.
Anyways. Just feeling out how I can maximize this phone's performance. NO plans on changing phones anytime soon.
Unidave199 said:
30 minutes? Woah that is a long time. Ok I will give it a try sometime when I go to bed.
I am mainly trying to get the PL1 update and not mess with Odin if I can get around it. I would like to try and port the Darklord Marshmellow ROM and take advantage of built in google assistant
So I thought I would try them. And always get back if I need to but wanted to keep the PL1 modem updates.
I only have one problem with one other phone user... She doesnt always get my texts and I dont always get hers. I dont know if others arent getting them and just dont know but my 1 friend I text a lot so she notices when there is a gap.
Anyways. Just feeling out how I can maximize this phone's performance. NO plans on changing phones anytime soon.
Click to expand...
Click to collapse
I still use my note 3. Granted not for main phone as I switched to iPhone, but I use it every day. I don't really know the hesitation of using Odin, but to each their own. If you did decide to use Odin, I'd flash the ROM, boot it, go to download mode again, flash TWRP, boot recovery (so it sticks and doesn't go back to stock recovery), flash SuperSU, done. You're rooted on PL1. Hopefully you have already backed up your text messages and other various things to either SDCard or something else. I'm not sure if that survives whether you wipe and flash clean or Odin. Depending on provider, that could be your issue with text messages. If you're with Sprint, check that you are on latest PRL. If not, make sure APN settings are correct.
If you're only looking for Assistant, I had it running on stock PL1. XDA did a blog post about enabling it in Lollipop, so once you upgrade, check it out. I couldn't stay on Marshmallow. Being that these are ports and not specifically built for our phone, I ran into issue with every single ROM either not being able to place calls, text (MMS actually), or wireless/data not working. No matter what I changed APN to, I would always have issues. Some do not. I just can't recommend a port when they haven't worked for me. Some roms have been abandoned, which meant if I found one that I could at least handle, it was so outdated that it was unusable (issues had arisen and the developer had moved on so they weren't being fixed). By handling a rom, I mean that after I upgraded to iPhone, I only needed wireless to work (to connect to hotspot) and it not go into a boot loop or crash all the time (some do). Those roms I have no idea if calls or text work because I wasn't using that. A lot have issues with wireless working.
One more thing you can try is to do a flash, wait about 30 minutes. If it still doesn't boot, pull the battery and reboot into recovery. Wipe data and cache and reboot again. It should boot. It'll still take a long time. Make sure you wait the 30 minutes before pulling the battery (it should have finished upgrading your system by then). Do note that first boot from now on will take forever no matter if it's a port or stock. Lollipop and higher take a long time to upgrade. I've only had 1 or 2 roms take around 5 minutes and that's because they were minimalist and without Google apps. The phone does get a little warm and uses a lot of battery, so I'd keep it plugged in.
Please report back if you got it to work and how. Like I said, I still use mine. I still visit this forum every day even though I've had an s5 and an s7 edge. I love this phone. I need to get mine replaced because I've worn it out: broken charger port so I have to make sure the cable is plugged in a certain way and I can't touch the phone while charging, side molding is broken off in places, some of my partitions can't be changed which means the memory is failing (not even Odin flashes correctly anymore let alone custom roms). But, it still keeps on ticking.
evilvoice said:
I still use my note 3. Granted not for main phone as I switched to iPhone, but I use it every day. I don't really know the hesitation of using Odin, but to each their own. If you did decide to use Odin, I'd flash the ROM, boot it, go to download mode again, flash TWRP, boot recovery (so it sticks and doesn't go back to stock recovery), flash SuperSU, done. You're rooted on PL1. Hopefully you have already backed up your text messages and other various things to either SDCard or something else. I'm not sure if that survives whether you wipe and flash clean or Odin. Depending on provider, that could be your issue with text messages. If you're with Sprint, check that you are on latest PRL. If not, make sure APN settings are correct.
If you're only looking for Assistant, I had it running on stock PL1. XDA did a blog post about enabling it in Lollipop, so once you upgrade, check it out. I couldn't stay on Marshmallow. Being that these are ports and not specifically built for our phone, I ran into issue with every single ROM either not being able to place calls, text (MMS actually), or wireless/data not working. No matter what I changed APN to, I would always have issues. Some do not. I just can't recommend a port when they haven't worked for me. Some roms have been abandoned, which meant if I found one that I could at least handle, it was so outdated that it was unusable (issues had arisen and the developer had moved on so they weren't being fixed). By handling a rom, I mean that after I upgraded to iPhone, I only needed wireless to work (to connect to hotspot) and it not go into a boot loop or crash all the time (some do). Those roms I have no idea if calls or text work because I wasn't using that. A lot have issues with wireless working.
One more thing you can try is to do a flash, wait about 30 minutes. If it still doesn't boot, pull the battery and reboot into recovery. Wipe data and cache and reboot again. It should boot. It'll still take a long time. Make sure you wait the 30 minutes before pulling the battery (it should have finished upgrading your system by then). Do note that first boot from now on will take forever no matter if it's a port or stock. Lollipop and higher take a long time to upgrade. I've only had 1 or 2 roms take around 5 minutes and that's because they were minimalist and without Google apps. The phone does get a little warm and uses a lot of battery, so I'd keep it plugged in.
Please report back if you got it to work and how. Like I said, I still use mine. I still visit this forum every day even though I've had an s5 and an s7 edge. I love this phone. I need to get mine replaced because I've worn it out: broken charger port so I have to make sure the cable is plugged in a certain way and I can't touch the phone while charging, side molding is broken off in places, some of my partitions can't be changed which means the memory is failing (not even Odin flashes correctly anymore let alone custom roms). But, it still keeps on ticking.
Click to expand...
Click to collapse
Come back to Android! We miss you!!!!
Yes I am backed up and also have a Titanium Backup of everything so I am pretty much covered... I have even backed up the backups to my PC!
You have much wisdom in what you are saying. I thought I would play around with some other ROM's and see what the potential is.
I hear good things about the Darklord Reborn by Midevil and JCorderno so thought I would investigate.
I am not opposed to using Odin, but I was at work, and no access to a computer so wanted to see if I could do the upgrade 'on the fly' since I am already rooted and with recovery.
Man, waiting 30 minutes for a phone to boot sounds like a anxiety attack waiting to happen! But still wanna give it a try.
As to your USB port. Have you thought of going wireless charging? I did and haven't looked back! You can get a wireless charging back and a case that will fit at...
for the charging back
https://smile.amazon.com/Samsung-Ga...=8-2&keywords=samsung+note+3+wireless+charger
for the case
https://smile.amazon.com/gp/product/B00F3KP156/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
Clone Wars....
Just wanted to put out a big THANKS for this.. I broke my Note 3 after 2,433 days (long story) but had bought a stock spare on Ebay last year... Making the switch now, but your PH1 Flashable update is making it super easy!
To let everyone who needs to use this nowdays... you will need to Flash an older TWRP (I used 2.7.8) in order to allow the Modem partition to be overwritten. Then you can flash up to 3.x to load a Android 10 based rom.
Related
Hi am obviously new to these forums but not new to Android/Samsung development so I had custom roms installed on my I777 so I needed to revert back to stock in which I flashed a leak which apparently changed the pit so I was able to download all the stock files for Odin3 for my device in the Download Repository. My question is there any reason why my device just doesn't act as accurately as I though I remembered it being when it was stock. Is there any ultimately right process for flashing because most instructions including my own are all different, some say wipe cache and data first and battery pull then download mode Creepys says its not neccessary until after the flash as does ZedoMax. I've followed all of them and haven't understood why there is no ultimately right process if there is one at all using odin3 and one-click. And if this is the case what could possibly be going on with the force closes and hangups I'm getting? If someone is willing to take the time to help me with all these questions I'd greatly appreciate it.
Dunno if it'll help, but it won't hurt..
Boot into recovery and"fix permissions". *Should* help with the FC's - oh, and delete everything from your memory that you read on galaxys2root (zedomax). Whatever you've read from creepy, COMMIT to memory. The guy is ace!
Clay
Team Pirate
Sent from my PINK SGH-I777
clay101eve said:
Dunno if it'll help, but it won't hurt..
Boot into recovery and"fix permissions". *Should* help with the FC's - oh, and delete everything from your memory that you read on galaxys2root (zedomax). Whatever you've read from creepy, COMMIT to memory. The guy is ace!
Clay
Team Pirate
Sent from my PINK SGH-I777
Click to expand...
Click to collapse
I don't see the option for fix permissions first of all is that a cwm option? Also I know creepy is one of the best but what's wrong with gs2root? And I appreciate the help but which process is the ultimate right way? Do you flash pit,PDA,modem all together or is that incorrect?
GalaxyHackster85 said:
I don't see the option for fix permissions first of all is that a cwm option? Also I know creepy is one of the best but what's wrong with gs2root? And I appreciate the help but which process is the ultimate right way? Do you flash pit,PDA,modem all together or is that incorrect?
Click to expand...
Click to collapse
I don't remember for sure, but I don't think fix permissions in available in stock 3e recovery. It should be available in just about any custom recovery.
GalaxyS2Root, and it's owner who goes by the screen name zedomax, is a strictly commercial endeavour, designed to make money but not necessarily designed to help people. I think zedomax is a developer, but I'm not sure how good he is. Many of the offerings on that web site, and presumably on his dozens of other web sites for other phones, cause problems for folks, bricking phones, and other things. Further, he takes the work of developers here and posts their work on his sites without giving any attribution or remuneration. He's spread way too thin keeping up with all his various sites, and/or he just doesn't seem to care if his offerings cause problems. We've had so many people come to this forum with various problems due to GalaxyS2Root that when the name is mentioned, everyone is on it right away.
I would only use the pit to repartition on the I777 when everything else fails. It can be a help, but you should be sure that you are going to have a successful flash before you use it, since it repartitions the memory space of the phone.
Most firmware for the I777 has everything in one .tar file, which you put into the PDA slot. If you are flashing just a param.lfs or just a sbl.bin, then that goes into the PDA slot. You can also flash a modem at the same time as the rest of the firmware, using the Modem slot, but most firmware packages have the modem in them too.
So essentially the oneclicks are absolutely the only thing I need in order to ensure a 100% successful restocking? And if so am I always suppose to factory wipe/cache then battery pull (3e recovery doesn't have a power off option)? The reason why I ask so many questions is A. A lot of peoples data isn't accurate as you've stated and its better for me to have as much data as possible when potentially getting into these things. And B. I've been flashing my S2 like a madman with OCD because as soon as I'd get a force close or any sort of hiccup happened I assumed it was because I flashed it wrong when in fact I was just following some of the directions that I've aqquired from here or GS2Root and so far everything has flashed with the same results but as its been forever since my phone was purchased so I can recall if these are just the normal hiccups that come with the inconsistancy of android. So to me I'm just trying to.make sure that I'm doing things absolutely correct.
There is lots of material here to read. You can learn a lot about your phone by spending some time reading.
creepyncrawly said:
There is lots of material here to read. You can learn a lot about your phone by spending some time reading.
Click to expand...
Click to collapse
And you are absolutely correct and I have your guide bookmarked but with so many people having different takes on how to return to stock can you point me in a direction that's the completely right way of flashing your pit and attempt software. Or is your guide with one click the most surefire way to do it? Like I said before I'm a bit OCD when it comes to my phone so whenever I get a little hiccup I can't tell if those are just normal for I777 software or is it something I've done wrong which I probably haven't but it still worries me.
If you havn't done something absolutely ignorant, i.e. flash firmware for a different phone, then you should just use my guide with the linked one-click downloader. That package does not contain bootloaders or param.lfs. Those (the bootloaders and param) will always be good, and not needing replaced, if you only flash firmware from these forums and never flash leaked firmware (which usually contains bootloaders.) There should never, ever be a reason to use a pit file. As I said before, the phone has to be pretty seriously screwed before you need to repartition, and then it should be the absolutely last thing you try.
And inform yourself before you do any actual flashing. You should know exactly what you are doing to your phone, and also know what the remedy is before you do it. That way, you can avoid doing something stupid. If you really want to learn about your phone, read at least a little bit from the forums here every day for a few months, get involved in the discussions, and before you know it, you'll be one of the helpers.
Thank you so much for all of your prompt replies, I have been using the data from this site for quite some years now but never ran into any issues which required me to create an account (although I have wanted to), but for s**ts and giggles let me just say that due to the few hiccups I encountered and not knowing what would have caused them I have already flashed the pit and repartitioned as well as flashed the oneclick w/ bootloaders and param. Now asside from the few force closes that I ran into and the one time I bricked it and brought it back to fully functional is there any harm to the flashing of those tools that I've already done so far. Is there any negative side effects of what I've done that I may not be seeing or is it a case of well "there in the repository so theyre safe as long as I've flashed them correctly". And if so are these few force closes just everyday hiccups that every version of Android experiences and that I'm just overthinking it and it's just been a case of my ocd kicking me in the ass?
The danger in using those files is in the flashing. If a flash is inadvertantly interrupted or goes bad, then it can hard brick the phone. Once the flash is complete and successful, then you're fine. There are no side effects.
Force closes, and other anomalies can be caused by conflicting data is the system and data partitions. They can also be the result of bugs in the firmware distribution or in any of the various applications. To eliminate the first cause, following all the best proceedures when flashing such as wiping first, etc eliminates the possibility that the fc's are caused by improper proceedure.
With proper installation proceedure, and with a stable firmware, and with robust applications, you should experience little to no fc's.
creepyncrawly said:
The danger in using those files is in the flashing. If a flash is inadvertantly interrupted or goes bad, then it can hard brick the phone. Once the flash is complete and successful, then you're fine. There are no side effects.
Force closes, and other anomalies can be caused by conflicting data is the system and data partitions. They can also be the result of bugs in the firmware distribution or in any of the various applications. To eliminate the first cause, following all the best proceedures when flashing such as wiping first, etc eliminates the possibility that the fc's are caused by improper proceedure.
With proper installation proceedure, and with a stable firmware, and with robust applications, you should experience little to no fc's.
Click to expand...
Click to collapse
i did zedo then s2 unlock then aokp then siyah kernal change forgot to do triangle away then tryed a ota update messed up rom cwm messed up then i just did zedo again to get cwm again then i did aokp again then ran triangle away then i return to stock backup after root then odin flash for stock non root then i took stock and did ota update to 2.3.6 i dont think we will ever get 2.3.7 because google wallet is on 2.3.7 and we cant have it correctly .....on reboot it hangs so i did 3e wipe and cache delete reboot all has been good since batt has been outragously long on uckk7 but after ota update it shows as uckk6 i used a non rooted file maybe u used a rooted return to stock file ?anyway file i used was I777UCKH7-CL503881-No-BL as stated just used pda slot .....idk after all the custom roms theres a distinct feeling in knowing your stock again but have the ability to go and do it all over again i honestly just miss the torch feature and the easy brightness slider on the pulldown
im getting h+ but it doesnt seem like true h+ speed and i also lose h+ while holding the phone im waiting for this to change with tmobile and thier 1900mhz i hope it does or ill be looking into whats going on with the modem maybe
colorsharpkid said:
i did zedo then s2 unlock then aokp then siyah kernal change forgot to do triangle away then tryed a ota update messed up rom cwm messed up then i just did zedo again to get cwm again then i did aokp again then ran triangle away then i return to stock backup after root then odin flash for stock non root then i took stock and did ota update to 2.3.6 i dont think we will ever get 2.3.7 because google wallet is on 2.3.7 and we cant have it correctly .....on reboot it hangs so i did 3e wipe and cache delete reboot all has been good since batt has been outragously long on uckk7 but after ota update it shows as uckk6 i used a non rooted file maybe u used a rooted return to stock file ?anyway file i used was I777UCKH7-CL503881-No-BL as stated just used pda slot .....idk after all the custom roms theres a distinct feeling in knowing your stock again but have the ability to go and do it all over again i honestly just miss the torch feature and the easy brightness slider on the pulldown
im getting h+ but it doesnt seem like true h+ speed and i also lose h+ while holding the phone im waiting for this to change with tmobile and thier 1900mhz i hope it does or ill be looking into whats going on with the modem maybe
Click to expand...
Click to collapse
Honestly, I have no idea what you just said, or what you're asking.
qwertyaas said:
Honestly, I have no idea what you just said, or what you're asking.
Click to expand...
Click to collapse
Me either, sometimes punctuation goes a long way
Sent from team Pirate! Using Tapatalk 2
colorsharpkid said:
i flashed zedo then used s2 unlock. then i flashed aokp and siyah kernel. I forgot to do triangle away (because I used zedo) and then tried an ota update. This messed up my rom because I couldn't access cwm. then i flashed zedo again to get cwm back. After that i flashed aokp again and ran triangle away.
I then did a return to stock backup after root and an odin flash for stock non root. While on stock i did an ota update to 2.3.6. (some nonsense about 2.3.7 and Google wallet)
.....on reboot it hangs so i did 3e recovery wipe and wiped cache. Reboot has been good since. My batt has been outragously long on uckk7!! But, after an ota update it shows as uckk6 i used a non rooted file, maybe I should have used a rooted return to stock file?
Anyway, the file i used was I777UCKH7-CL503881-No-BL as stated and i just used pda slot .....idk, after all the custom roms theres a distinct feeling in knowing your stock again but have the ability to go and flash custom ROMs all over again. i honestly just miss the torch feature and the easy brightness slider on the pulldown.
im getting h+ but it doesnt seem like true h+ speed and i also lose h+ while holding the phone. im waiting for this to change with tmobile and thier 1900mhz i hope it does or ill be looking into whats going on with the modem maybe
Click to expand...
Click to collapse
Fixed... I think. And "zedo" refers to the sh;t zedomax has on gs2root.
Clay
Team Pirate
Sent from my Buttery Pink SGH-i777
Ok thats where I'm a bit concerned because I ran into an issue before where I was going to do a flash and it choked up on me (mind you it was a pit and tar flash repartition) and it bricked on me but I was able to reflash the same process again once the pc was ok again. I also had on flash that was the 2.3.5 leak but flashed over that and it was fine. Now with that said the phone flashed well, and now it runs generally like it should have in the first place. But my question is did that fluke flash do anything negative to the device behind the scenes that will never be ok again?
creepyncrawly said:
The danger in using those files is in the flashing. If a flash is inadvertantly interrupted or goes bad, then it can hard brick the phone. Once the flash is complete and successful, then you're fine. There are no side effects.
Force closes, and other anomalies can be caused by conflicting data is the system and data partitions. They can also be the result of bugs in the firmware distribution or in any of the various applications. To eliminate the first cause, following all the best proceedures when flashing such as wiping first, etc eliminates the possibility that the fc's are caused by improper proceedure.
With proper installation proceedure, and with a stable firmware, and with robust applications, you should experience little to no fc's.
Click to expand...
Click to collapse
Ok thats where I'm a bit concerned because I ran into an issue before where I was going to do a flash and it choked up on me (mind you it was a pit and tar flash repartition) and it bricked on me but I was able to reflash the same process again once the pc was ok again. I also had on flash that was the 2.3.5 leak but flashed over that and it was fine. Now with that said the phone flashed well, and now it runs generally like it should have in the first place. But my question is did that fluke flash do anything negative to the device behind the scenes that will never be ok again?
Sorry for double post but I wanted to make sure my questions are targeting creepy seeing as this thread is getting a bit off topic.
GalaxyHackster85 said:
Ok thats where I'm a bit concerned because I ran into an issue before where I was going to do a flash and it choked up on me (mind you it was a pit and tar flash repartition) and it bricked on me but I was able to reflash the same process again once the pc was ok again.
Click to expand...
Click to collapse
As far as I know, that would be fine. Someone with dev experience could look into partition sizes on the phone, and see what actually happened. As long as the firmware is functioning correctly, then I would assume the partition sizes are correct.
I also had on flash that was the 2.3.5 leak but flashed over that and it was fine.
Click to expand...
Click to collapse
I guess you didn't get a crippled bootloader. That was the main problem with some of the leaks.
Now with that said the phone flashed well, and now it runs generally like it should have in the first place. But my question is did that fluke flash do anything negative to the device behind the scenes that will never be ok again?
Click to expand...
Click to collapse
I don't know how to look behind the scenes... but I would think your phone is fine.
creepyncrawly said:
As far as I know, that would be fine. Someone with dev experience could look into partition sizes on the phone, and see what actually happened. As long as the firmware is functioning correctly, then I would assume the partition sizes are correct.
I guess you didn't get a crippled bootloader. That was the main problem with some of the leaks.
I don't know how to look behind the scenes... but I would think your phone is fine.
Click to expand...
Click to collapse
OK great info and definitely a relief but just out.of curiousity what are the repercussions of a bad bootloader flash or an improper pit flash? And how would we know that whatever pit or bootloaders flashed weren't for our phone or are corrupted data?
creepyncrawly said:
As far as I know, that would be fine. Someone with dev experience could look into partition sizes on the phone, and see what actually happened. As long as the firmware is functioning correctly, then I would assume the partition sizes are correct.
I guess you didn't get a crippled bootloader. That was the main problem with some of the leaks.
I don't know how to look behind the scenes... but I would think your phone is fine.
Click to expand...
Click to collapse
And trust me I absolutely appreciate all the responses the answer to my last question is all I needed to know to truly understand how the i777 works and functions and I commend you for that. I felt that trying to find all these answers would have been trying to find a needle in a haystack.
Also regarding the repartioning I just wanted to make sure that everything is correct in terms of space. My device is showing only 1.89gb of "Device Memory" at the bout of the "Storage" screen is this normal I though it was higher before but I cant quite remember.
Wow! I need some help. I've acquired a Samsung Galaxy Note (i717, I believe) that shows all the signs of being healthy (appearance, touch screen, etc.) but persistently slows down at the ATT opening splash screen, begins to load Android, dies and reboots. Whatever variant rooted ROM I received it with (sluggish and unreliable) I have written over and now I can't get any farther than the Android settings screen. Therefore I do not know the exact version nor can I begin to set it up (wifi, etc.).
That's the 'presenting problem', so let me explain what I've done to this point (about 25 hrs. worth!). I have reloaded latest version of CWM (runs great) and then Padawan JB . . . same symptoms. I have loaded the ATT JB and ICS via the latest Odin successfully . . . with same symptoms. I have loaded TWRP (touch screen is snappy and works as it should) and Padawan JB again . . . with same symptoms. I have wiped caches before, after, and in between till I'm blue in the face, each time with the same symptoms. Most recently I have done a hard reset to native/factory settings . . . with no change! I've tried to scour the XDA (and any other sites) trouble shooting articles and seem to have come to a dead end.
Here's a couple things that I'm wondering: because I can't get deep enough into Android to check out the model number, could the phone be something other than an ATT model? At the top of the front face it simply says 'Samsung', not ATT at top and Samsung at bottom like my previous ATT Note. Right after boot I persistently get an ATT splash screen which would lead me to believe that it is ATT. Is there some other way to find model, say in TWRP? Do I need a phone specific version of Android? Second, everything seems to be working fine physically (i.e., no hardware problems). Could this thing have gotten a virus in an earlier life that's preventing the ROM from working right? I've not been able to get far enough to register it with my cell provider (second party, not ATT). Must you be up and running with the cell service to correctly load and use the ROM (wouldn't think so)? And if so, how without Android working? I've been using and playing with computers for 25 years, but I'm fairly new to the Android system (but learning fast!) Any help would sure be appreciated. I'd really like to resurrect this baby. I loved my first Note (till it fell off the car and disappeared).
pstrulm said:
Wow! I need some help. I've acquired a Samsung Galaxy Note (i717, I believe) that shows all the signs of being healthy (appearance, touch screen, etc.) but persistently slows down at the ATT opening splash screen, begins to load Android, dies and reboots. Whatever variant rooted ROM I received it with (sluggish and unreliable) I have written over and now I can't get any farther than the Android settings screen. Therefore I do not know the exact version nor can I begin to set it up (wifi, etc.).
That's the 'presenting problem', so let me explain what I've done to this point (about 25 hrs. worth!). I have reloaded latest version of CWM (runs great) and then Padawan JB . . . same symptoms. I have loaded the ATT JB and ICS via the latest Odin successfully . . . with same symptoms. I have loaded TWRP (touch screen is snappy and works as it should) and Padawan JB again . . . with same symptoms. I have wiped caches before, after, and in between till I'm blue in the face, each time with the same symptoms. Most recently I have done a hard reset to native/factory settings . . . with no change! I've tried to scour the XDA (and any other sites) trouble shooting articles and seem to have come to a dead end.
Here's a couple things that I'm wondering: because I can't get deep enough into Android to check out the model number, could the phone be something other than an ATT model? At the top of the front face it simply says 'Samsung', not ATT at top and Samsung at bottom like my previous ATT Note. Right after boot I persistently get an ATT splash screen which would lead me to believe that it is ATT. Is there some other way to find model, say in TWRP? Do I need a phone specific version of Android? Second, everything seems to be working fine physically (i.e., no hardware problems). Could this thing have gotten a virus in an earlier life that's preventing the ROM from working right? I've not been able to get far enough to register it with my cell provider (second party, not ATT). Must you be up and running with the cell service to correctly load and use the ROM (wouldn't think so)? And if so, how without Android working? I've been using and playing with computers for 25 years, but I'm fairly new to the Android system (but learning fast!) Any help would sure be appreciated. I'd really like to resurrect this baby. I loved my first Note (till it fell off the car and disappeared).
Click to expand...
Click to collapse
Well, if you keep flashing an AT&T based rom, then yes, you will get an AT&T boot animation simply because it's part of the rom you are flashing.
You said "you think" you have an I717, did you take the battery off and physically look at the sticker beneath it to see the model?
Try TWRP, go to WIPE, and WIPE everything, which means checking every checkbox. Then flash a stock rom with a fresh phone (no data, nothing at all)
You said you did CWM->Padawan.. these are two totally different roms, so you should always do a factory reset whenever flashing two totally different roms.
You can't just rely on the Android->settings to see the info since roms overwrite these stuff in build.prop so if you flash a wrong rom, wrong info will show up.
Here's my advice:
1. Flash TWRP
2. Wipe in TWRP, check every checkbox
3. Flash a stock i717 rom
4. Reboot
If that doesn't work, either hardware is bad or your phone isn't for the I717 roms.
Edit:
Question, have you ever come to a point that the phone boots successfuly at all? You did mention CM works great. But you can't go from CWM->TW Based rom without factory reset in between.
fbauto1 said:
Well, if you keep flashing an AT&T based rom, then yes, you will get an AT&T boot animation simply because it's part of the rom you are flashing.
You said "you think" you have an I717, did you take the battery off and physically look at the sticker beneath it to see the model?
Try TWRP, go to WIPE, and WIPE everything, which means checking every checkbox. Then flash a stock rom with a fresh phone (no data, nothing at all)
You said you did CWM->Padawan.. these are two totally different roms, so you should always do a factory reset whenever flashing two totally different roms.
You can't just rely on the Android->settings to see the info since roms overwrite these stuff in build.prop so if you flash a wrong rom, wrong info will show up.
Here's my advice:
1. Flash TWRP
2. Wipe in TWRP, check every checkbox
3. Flash a stock i717 rom
4. Reboot
If that doesn't work, either hardware is bad or your phone isn't for the I717 roms.
Edit:
Question, have you ever come to a point that the phone boots successfuly at all? You did mention CM works great. But you can't go from CWM->TW Based rom without factory
I would reflash cwm thru odin after that I would flash the latest TWRP 2.5. Then you can flash whatever. If padawan is givin u problems try something else like AOSP or AOKP. Padawan is TW based. JaimeD builds are pretty sweet.
sent from my GalaxySuperNote running OC Padawan JB
Click to expand...
Click to collapse
androidmechanic said:
fbauto1 said:
Well, if you keep flashing an AT&T based rom, then yes, you will get an AT&T boot animation simply because it's part of the rom you are flashing.
You said "you think" you have an I717, did you take the battery off and physically look at the sticker beneath it to see the model?
Try TWRP, go to WIPE, and WIPE everything, which means checking every checkbox. Then flash a stock rom with a fresh phone (no data, nothing at all)
You said you did CWM->Padawan.. these are two totally different roms, so you should always do a factory reset whenever flashing two totally different roms.
You can't just rely on the Android->settings to see the info since roms overwrite these stuff in build.prop so if you flash a wrong rom, wrong info will show up.
Here's my advice:
1. Flash TWRP
2. Wipe in TWRP, check every checkbox
3. Flash a stock i717 rom
4. Reboot
If that doesn't work, either hardware is bad or your phone isn't for the I717 roms.
Edit:
Question, have you ever come to a point that the phone boots successfuly at all? You did mention CM works great. But you can't go from CWM->TW Based rom without factory
I would reflash cwm thru odin after that I would flash the latest TWRP 2.5. Then you can flash whatever. If padawan is givin u problems try something else like AOSP or AOKP. Padawan is TW based. JaimeD builds are pretty sweet.
sent from my GalaxySuperNote running OC Padawan JB
Click to expand...
Click to collapse
If you want TWRP, flash TWRP. No need to flash CWM
Click to expand...
Click to collapse
AT&T Phones have a [logo}AT&T] on the top-center!!
But if you are in doubt, use kies to do a full recovery-restore [WILL ERASE EVERYTHING ON YOUR DEVICE].
See post #4 on this thread.
fbauto1 said:
androidmechanic said:
If you want TWRP, flash TWRP. No need to flash CWM
Click to expand...
Click to collapse
If you go thru Odin you would have cwm first. With the problems talked about, I would go back factory stock then re-root with Odin. Then thru cwm, flash twrp or whatever floats your boat.
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
androidmechanic said:
If you go thru Odin you would have cwm first. With the problems talked about, I would go back factory stock then re-root with Odin. Then thru cwm, flash twrp or whatever floats your boat.
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Nope. If you want TWRP, then flash TWRP via Odin. No need to go through CWM first. You can flash TWRP via Odin, you know that, right?
fbauto1 said:
Nope. If you want TWRP, then flash TWRP via Odin. No need to go through CWM first. You can flash TWRP via Odin, you know that, right?
Click to expand...
Click to collapse
No I didn't know that. All of the Odin programs that I dealt with flash cwm. Than for the Intel tho. :thumbup:
Sent from my SAMSUNG-SGH-I717 using xda premium
fbauto1 said:
Nope. If you want TWRP, then flash TWRP via Odin. No need to go through CWM first. You can flash TWRP via Odin, you know that, right?
Click to expand...
Click to collapse
androidmechanic said:
No I didn't know that. All of the Odin programs that I dealt with flash cwm. Than for the Intel tho. :thumbup:
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
you are both actually correct, however, I am looking at PSTRULM's stats. if he is anything like me when I started, the more simple and less complication involved in the process, the more he may understand.
ANDROIDMECHANIC is stating the most basic and beginner way to do this and understand simply. after doing this a few times as I did, the basic mechanics of the process will become more fluent.
then he can make his own decisions as to methods which might be easier for him, without confusing.
I am sure you both are a huge help to everyone and I thank members such as yourself for your efforts. ME, I prefer baby steps, cause I know I can really EFF things up if I get confused
androidmechanic said:
No I didn't know that. All of the Odin programs that I dealt with flash cwm. Than for the Intel tho. :thumbup:
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Just a reminder.. when flashing through Odin, make sure it's an ODIN-flashable tarball, i.e., you can't flash a recovery-type zip through Odin and vice versa.
Hey guys, has anyone had this issue where your camera refuses to focus on anything further away than say about 6 inches? It can focus just fine close up, but beyond that it's garbage. It goes through the 'animation' of focusing, turns red like i can't focus, and doesn't actually adjust the focus at all. It started in about October and has persisted through 3 or 4 ROMs and various camera APKs.
Has anyone replaced their camera before? I doubt verizon would trade me for a new phone seeing as I've rooted it and flashed a lot of ROMs on it. What should I do? What have you done if this has happened to you? This thread outlines exactly the same thing I'm experiencing and seems as they've concluded it's hardware failure.
Thoughts?
Bump in hopes of someone's experience or advice.
falkon114 said:
Hey guys, has anyone had this issue where your camera refuses to focus on anything further away than say about 6 inches? It can focus just fine close up, but beyond that it's garbage. It goes through the 'animation' of focusing, turns red like i can't focus, and doesn't actually adjust the focus at all. It started in about October and has persisted through 3 or 4 ROMs and various camera APKs.
Has anyone replaced their camera before? I doubt verizon would trade me for a new phone seeing as I've rooted it and flashed a lot of ROMs on it. What should I do? What have you done if this has happened to you? This thread outlines exactly the same thing I'm experiencing and seems as they've concluded it's hardware failure.
Thoughts?
Click to expand...
Click to collapse
I think you're right on the hardware issue. You could always use ODIN to restore the phone back to stock and turn it in for replacement. Verizon can't tell the difference as long as you restore it with the proper factory image. Bad thing is, replacement will probably come locked down with the currently unlockable 4.3 bootloader. At the very least you can restore it with ODIN just to see if it helps the focus issue.
*see below*
Jiggabitties said:
I think you're right on the hardware issue. You could always use ODIN to restore the phone back to stock and turn it in for replacement. Verizon can't tell the difference as long as you restore it with the proper factory image. Bad thing is, replacement will probably come locked down with the currently unlockable 4.3 bootloader. At the very least you can restore it with ODIN just to see if it helps the focus issue.
Click to expand...
Click to collapse
Yeah, i think I might try going back to stock. I wanted to a little while ago just to remember what it was like having a stock system, but I can't find all the files I need. Wasn't there a sticky with Odin and all the right files in one thread? Thought it was stickied, but either I'm blind, or I'm not finding it.
Edit:
Nvm, I'm an idiot
falkon114 said:
Yeah, i think I might try going back to stock. I wanted to a little while ago just to remember what it was like having a stock system, but I can't find all the files I need. Wasn't there a sticky with Odin and all the right files in one thread? Thought it was stickied, but either I'm blind, or I'm not finding it.
Edit:
Nvm, I'm an idiot
Click to expand...
Click to collapse
Yeah sometimes I go back to stock for a day or two just to remind myself why crack flashing is so worth it. But sometimes it's just needed to iron out some bugs. I was having radio issues not too long ago, tried different roms and radios and couldn't fix it. Flashed back to stock, worked like a charm. Haven't had an issue since.
Jiggabitties said:
Yeah sometimes I go back to stock for a day or two just to remind myself why crack flashing is so worth it. But sometimes it's just needed to iron out some bugs. I was having radio issues not too long ago, tried different roms and radios and couldn't fix it. Flashed back to stock, worked like a charm. Haven't had an issue since.
Click to expand...
Click to collapse
Alright, so I remember having some problems when I was first rooting/modifying/Custom recovery-ing...
Couple questions.
1. I use TWRP as my recovery of choice. Can I backup my current ROM as is and store it through there like I normally would when going to a new ROM in case I want to after I go back to stock? Or will going back to stock completely erase all saved ROM images?
If I go back to stock, can I boot into TWRP again like I do now, or is there some process I'll need to follow again to be able to flash my current ROM image? Should I flash the Root66 stock VRALJB 4.1.1 (12/2/12) in the previously linked thread so I can still use custom recovery?
What else should I know? I've become quite good and confident in flashing ROMs, but I'm nervous going back to stock since it seems easier to brick it/lock it down. I remember when I first downloaded and tried installing TWRP, it showed that infamous Yellow Triangle saying the device found unauthorized software and to take it to Verizon, and I remember spending hours trying to flash things to get past that, I don't want to have to deal with that again.
falkon114 said:
Alright, so I remember having some problems when I was first rooting/modifying/Custom recovery-ing...
Couple questions.
1. I use TWRP as my recovery of choice. Can I backup my current ROM as is and store it through there like I normally would when going to a new ROM in case I want to after I go back to stock? Or will going back to stock completely erase all saved ROM images?
If I go back to stock, can I boot into TWRP again like I do now, or is there some process I'll need to follow again to be able to flash my current ROM image? Should I flash the Root66 stock VRALJB 4.1.1 (12/2/12) in the previously linked thread so I can still use custom recovery?
What else should I know? I've become quite good and confident in flashing ROMs, but I'm nervous going back to stock since it seems easier to brick it/lock it down. I remember when I first downloaded and tried installing TWRP, it showed that infamous Yellow Triangle saying the device found unauthorized software and to take it to Verizon, and I remember spending hours trying to flash things to get past that, I don't want to have to deal with that again.
Click to expand...
Click to collapse
Yes, backup your current ROM, if you use the root66 Odin image it should not erase anything you have stored. But to be safe, I would copy your TWRP backup to either an external SD or to your computer for safe keeping. TWRP should survive, as long as you use root66, the others will overwrite recovery and lock the bootloader.
The only reason you should ever get the "Yellow Triangle", or trip any sort of security is if you attempt to install a custom recovery or ROM while the bootloader remains locked, or, you attempted to install the recovery via ODIN.
The most important thing here is, whatever you do, under any circumstance, DO NOT accept any OTA updates. As long as you don't accept the 4.3 OTA, you should be able to keep your TWRP.
You may want to try this flashable version of the stock VRAMC3 before you resort to ODIN http://forum.xda-developers.com/showthread.php?t=2261478
Jiggabitties said:
Yes, backup your current ROM, if you use the root66 Odin image it should not erase anything you have stored. But to be safe, I would copy your TWRP backup to either an external SD or to your computer for safe keeping. TWRP should survive, as long as you use root66, the others will overwrite recovery and lock the bootloader.
The only reason you should ever get the "Yellow Triangle", or trip any sort of security is if you attempt to install a custom recovery or ROM while the bootloader remains locked, or, you attempted to install the recovery via ODIN.
The most important thing here is, whatever you do, under any circumstance, DO NOT accept any OTA updates. As long as you don't accept the 4.3 OTA, you should be able to keep your TWRP.
You may want to try this flashable version of the stock VRAMC3 before you resort to ODIN http://forum.xda-developers.com/showthread.php?t=2261478
Click to expand...
Click to collapse
Thanks. I tried the last link there, and am back to relatively stock and still have the camera issue.
I'm excited for the 4.3 update to be hacked since I would really, really like multi-window and SNote capabilities on my 4.3 ROM, but who knows when that might happen.
Thanks for you help man!
falkon114 said:
Thanks. I tried the last link there, and am back to relatively stock and still have the camera issue.
I'm excited for the 4.3 update to be hacked since I would really, really like multi-window and SNote capabilities on my 4.3 ROM, but who knows when that might happen.
Thanks for you help man!
Click to expand...
Click to collapse
Glad I could help in any way. Bummer about your camera.
I'm gonna go out on a limb here & ask a question that's been on my mind for a while, so bear with me. But first, let me give you some background so there's no confusion & no unnecessary questions asked. I'm by no means a "pro" at modifying my Note 3, I just follow instructions carefully & then implement those directions to achieve results. That's how I rooted my Note 3 but could still care less that I tripped Knox in the end.
I have the 32 GB Sprint Galaxy Note 3 with an 8 GB microSD. It's rooted using Chainfire's method. I also have TWRP for a recovery, but I'm using the stock Sprint ROM that came with it. I have a few root apps installed (Titanium backup, AdAway & Root Explorer) but the rest are what Sprint (& Android) put in there, minus a few that are totally unnecessary for me...(chat apps, picture drawings, step counting & so on) that were removed with Titanuim. It's still on 4.3 Jellybean with PUBMJ4 baseband. I also have the Wi-Fi hotspot fixed through 2 file replacements using Root Explorer.
Now that you know what I have, onto the question...
I see many, many ROMs in other threads that I'd like to try out, but don't know how to go about doing this. Before you jump right in & answer, here's my problem. If I try a ROM but don't like it, or it doesn't suit my needs, how can I go about going back to what I have now in the best (& fewest) steps necessary? In other words, to go back to exactly what ROM I have now, the apps installed, baseband, the whole nine yards. Just like a computer backup, it's a bit-for-bit restore, completely mirroring the hard drive. Understand?
Maybe you could explain to me like I'm seven years old what apps I need, what procedures are taken, the order in which they happen & so on. If I need an app or two to do just this, I have approximately $20 Google Play credit left.
Can a DEV or an experienced person that's done just this help a fellow out? Don't get me wrong, the stock ROM I'm using works for me, but there's ROMs posted that look just awesome! It's all about "personalization", am I right?
Easy, since you have a custom recovery installed (twrp) , you simply do a "nandroid" backup (I personally like to backup to an external SD card, so get a bigger one) before wiping and installing something new. If you like what you got, fine. If you want to go back, wipe and restore! Easy Peasy!
Sorry, being a father means sometimes your time suddenly becomes unavailable. But believe me, it's really easy once you figure out twrp.
I'll let another fine member get more details if you actually need them. ?
Sent from my calculator watch.
So did you figure it all out?
Sent from my SM-N900P using Tapatalk
kingdazy said:
Easy, since you have a custom recovery installed (twrp) , you simply do a "nandroid" backup (I personally like to backup to an external SD card, so get a bigger one) before wiping and installing something new. If you like what you got, fine. If you want to go back, wipe and restore! Easy Peasy!
Sorry, being a father means sometimes your time suddenly becomes unavailable. But believe me, it's really easy once you figure out twrp.
I'll let another fine member get more details if you actually need them. ?
Sent from my calculator watch.
Click to expand...
Click to collapse
Doing a Nandroid backup as we speak! I didn't realize TWRP could do that. (duh! ) I only installed TWRP because I just liked the name of it. TWERP!! (gotta nice sound to it, doesn't it??) Thanks a bunch! :good:
tonyevo52 said:
So did you figure it all out?
Sent from my SM-N900P using Tapatalk
Click to expand...
Click to collapse
I did. I found a Youtube link on how to do a TWRP backup on the Sprint Note 3. Easy Peasy as said above! I'll try some ROMs this weekend (can't promise nuthin' cause it's gonna be 70 degrees this weekend & I'm itchin' to ride my mountainbike along the boardwalk at the Virginia Beach.)
But now that the hard part is outta the way, it's all easy street from here!
Just be sure to Please, oh god Please, read all instructions on any rom you decide to try. Doesn't hurt to read the last 10 pages of each too, get an idea of Current issues that may not be documented in the OP.
And don't get lazy, follow word for word. The only times I f*cked stuff up was when I didn't follow instructions (ie, thought my experience meant I knew best), or just got sloppy.
And, don't forget to wipe! (I wipe 3X, everytime, as a habit. Some people will give you reasons why that's unnecessary, but I can say confidently, if perhaps anecdotally, that I Never have the issues others have with bad flashes, softbricks, FCs, etc.)
Something to get comfortable with, even though you may never need it is ODIN. It's most common use is a utility for flashing stock ROMs and firmwares, great for recovery from bad things. Again, you may never need it, but have it ready in your Pc with a stock ROM file, just in case.
Finally, Titantium Backup can be your best friend, if used properly. It can also be a real pain, so don't become too dependant on it.
FIN
Sent from my calculator watch.
kingdazy said:
Just be sure to Please, oh god Please, read all instructions on any rom you decide to try. Doesn't hurt to read the last 10 pages of each too, get an idea of Current issues that may not be documented in the OP.
And don't get lazy, follow word for word. The only times I f*cked stuff up was when I didn't follow instructions (ie, thought my experience meant I knew best), or just got sloppy.
And, don't forget to wipe! (I wipe 3X, everytime, as a habit. Some people will give you reasons why that's unnecessary, but I can say confidently, if perhaps anecdotally, that I Never have the issues others have with bad flashes, softbricks, FCs, etc.)
Something to get comfortable with, even though you may never need it is ODIN. It's most common use is a utility for flashing stock ROMs and firmwares, great for recovery from bad things. Again, you may never need it, but have it ready in your Pc with a stock ROM file, just in case.
Finally, Titantium Backup can be your best friend, if used properly. It can also be a real pain, so don't become too dependant on it.
FIN
Sent from my calculator watch.
Click to expand...
Click to collapse
No worries! As I said in the OP, I follow directions carefully. I read everything.
Odin is my friend as well. I have it installed on my laptop. That's how I flashed basebands & deodexed stock rooted ROMs on my Galaxy S III. I also have the original stock Sprint ROM for this GN3 "just in case", in a folder sitting on my desktop with a few extra tools. I've never bricked a phone, unless you count using Samsung's online update (can't think of the name at the moment). It said 4.3 was available, so I downloaded it. It flashed, rebooted, but stuck there. Never finished the boot, just gave me an error code. Samsung's own update killed my GS3 & was unrecoverable. Believe me, I tried everything. What was strange, was the ROM was 4.3 but the baseband was the previous version, not the newer one, so the phone just puked. It never updated the baseband so it bricked. Now, I tried (and used) different radios with no problems before the update. Everything worked in harmony. Go figure!
Time for sleep my friend. Gotta work in the morning!
As the title states, my Verizion SCH-i545 will lockup, shutdown and be unresponsive for long peroids of time ( read 24-96 hrs ) , unable to even take a charge.
What i think happened: I was trying to push boot loader files into my Kindle Fire HD 7" and *whoops* forgot to unplug my phone from the USB cord where it was charging merrily away. Since then I have gotten it to turn on a small handful of times - the most recent was after a 3 day wait for the battery to discharge and then it decided to accept a charge, worked for around 20 hours and then locked up again. Since that point it has been unresponsive.
I'm thinking that these boot loader files may have overwritten primary-boot and possibly secondary-boot sectors and sometimes the secondary-boot backup partition catches, and sometimes it doesn't.
I know what you all are thinking, and the guys I'm deployed with tell me the same thing - send it in as an insurance claim and get a new one. Well screw that, especially if I can get it done myself. I've also read that this is a possible hard-brick ( i don't think so since I can get something from it, sometimes ) and in need of a RIFF box to get this done properly.
At our last port, I was in the XDA-DEV chat room on snoonet and someone mentioned that the aboot.img may be disfigured or completely screwed, but being in port, I was fairly drunk and didn't save the log from that chat like I should have, does this sound right?
Can anyone give me any guidance as to what is going on with my phone and how to fix it? I have a stock Samsung ROM image on the way out here shipped from the states, but that's about a week away, at least. Will this be enough to fix it? Is there anything I can do to get my phone back operational in the mean time?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=2735172
This is a link to the full wipe and no wipe nc5 tar images. Nc5 is the latest official firmware (4.4.2). These files are to be flashed with Odin. You can try the no wipe first so you don't lose your data but you might need the full wipe which will return you to total factory stock. I don't know how the network speeds are where you're deployed but be warned, these are big files.
joshm.1219 said:
http://forum.xda-developers.com/showthread.php?t=2735172
This is a link to the full wipe and no wipe nc5 tar images. Nc5 is the latest official firmware (4.4.2). These files are to be flashed with Odin. You can try the no wipe first so you don't lose your data but you might need the full wipe which will return you to total factory stock. I don't know how the network speeds are where you're deployed but be warned, these are big files.
Click to expand...
Click to collapse
I appreciate the super quick reply. I know that I'm still running MDK base band but if I can still root the NC5 and reinstall my Hyperdrive, I'll be ecstatic about this. Maybe at our next port I'll be able to download some of these images, but if the image that I have coming from the states will work, then I'll just run with that.
As far as downloading goes, it's a no go out here. Satellite internet that barely allows me to browse XDA, let alone download a GB worth of files.
And as far as wiping? I have no qualms, I've already shed my tears over wiping my phone and somehow my SD card got corrupted and I lost all of my pre-deployment pictures with my family. I've already shed my tears and lost everything that I can lose on that phone. At this point I just want to get it working again. As a sort of GFY to Samsung who told me I needed to send it in to them to have it fixed with authorized samsung equipment and authorized samsung techs.
Anyways, thanks for the quick reply, once I get my image from the states and give that a whirl I'll report back here if it worked. if not, I'm just waiting for our next port to download some of these images and try try again.
breakneat said:
I appreciate the super quick reply. I know that I'm still running MDK base band but if I can still root the NC5 and reinstall my Hyperdrive, I'll be ecstatic about this. Maybe at our next port I'll be able to download some of these images, but if the image that I have coming from the states will work, then I'll just run with that.
As far as downloading goes, it's a no go out here. Satellite internet that barely allows me to browse XDA, let alone download a GB worth of files.
And as far as wiping? I have no qualms, I've already shed my tears over wiping my phone and somehow my SD card got corrupted and I lost all of my pre-deployment pictures with my family. I've already shed my tears and lost everything that I can lose on that phone. At this point I just want to get it working again. As a sort of GFY to Samsung who told me I needed to send it in to them to have it fixed with authorized samsung equipment and authorized samsung techs.
Anyways, thanks for the quick reply, once I get my image from the states and give that a whirl I'll report back here if it worked. if not, I'm just waiting for our next port to download some of these images and try try again.
Click to expand...
Click to collapse
Man that's rough now I see why you have to have it shipped. Hope it works.
Op makes good on promise! Op replies!
My files got here the other day, and I was able to reflash with MJ7 firmware. After that I spent a solid 2 hrs ( had to pay off people to download these files - limited computer time and what not ) downloading Safestrap and Saferoot and then subsequently installing an old copy of Hyperdrive ( RLS 14 ). Could I have just flashed Hyperdrive with Odin and been okay? Or did I have to have a stock firmware to repair the issue? BTW, thats 7MB in 2 hours.
Also, I've been reading up on Hyperdrive RLS 17, and it says that I've got to flash NC5 firmware before I do RLS 17? With Safestrap, would I just flash NC5 into the stock slot, and then HD 17 into a subsequent slot? Or could I do like I did with HD14 and flash right into the stock slot with no apparent issues.
BTW, you being the only respondent to this post, I thank you lots for your help.