I am not responsible for bricked devices, dead SD cards, explosions, wars, broken phone or charger, or you getting fired because the alarm application failed, Please read the first 2 posts carefully before deciding to install this app.
This is my new app to control charging current on Redmi Note 3 (Snapdragon) , to use this app you must be on any 6.0.1 or 7.1.1 rom, this will not work on 5.1.1 roms. The app is compatible with all kernels including stock cm kernel. Increasing charge rate is not always effective because of hardware limitations, but decreasing it below 2000 works very effectively.
Usage Instructions -
Install the kenzo charge control app
Open the app and wait for it to set permissions
Enter charge rate value and click set rate button
Enjoy your custom charge rate
Important Information -
Don't use very high values, prefer to stay below 2500 mA current
Compatible only with RN3(Snapdragon) and only with CM/ASOP roms
There is no apply on boot option yet, I'm little lazy to add that
Downloads -
Kenzo Charge Control V1.1
XDA:DevDB Information
Kenzo Charge Control, Device Specific App for the Xiaomi Redmi Note 3
Contributors
Umang96
Version Information
Status: Stable
Created 2016-08-28
Last Updated 2016-08-28
Changelogs -
V1.1 -
Fixed some force closes on clicking buttons before permissions are set
Compatible with all official cm/aosp based roms and kernels
V1.0 -
Initial version for kenzo
Blaze kernel + hexagon ROM ; when i press check rate i always get " still setting permissions " even though i wait for more than 30s
aaz03 said:
Blaze kernel + hexagon ROM ; when i press check rate i always get " still setting permissions " even though i wait for more than 30s
Click to expand...
Click to collapse
Make sure your charger is not plugged it, it should work then, if still not working then try with my kernel, it works fine for me.
Are you gonna release version for miui based Roms?
Wysłane z mojego Redmi Note 3 przy użyciu Tapatalka
Umang96 said:
I am not responsible for bricked devices, dead SD cards, explosions, wars, broken phone or charger, or you getting fired because the alarm application failed, Please read the first 2 posts carefully before deciding to install this app.
This is my new app to control charging current on Redmi Note 3 (Snapdragon) , to use this app you must be on any cm or aosp rom, this will not work on miui roms. The app is compatible with all kernels including stock cm kernel. Increasing charge rate is not effective because of hardware limitations, but decreasing it below 2000 works very effectively.
Usage Instructions -
Install the kenzo charge control app
Open the app and wait for it to set permissions
Enter charge rate value and click set rate button
Enjoy your custom charge rate
Important Information -
Don't use very high values, prefer to stay below 2500 mA current
Compatible only with RN3(Snapdragon) and only with CM/ASOP roms
There is no apply on boot option yet, I'm little lazy to add that
Downloads -
Kenzo Charge Control V1.1
XDA:DevDB Information
Kenzo Charge Control, Device Specific App for the Xiaomi Redmi Note 3
Contributors
Umang96
Version Information
Status: Stable
Created 2016-08-28
Last Updated 2016-08-28
Click to expand...
Click to collapse
By this, can I charge my mobile faster?
Sent from my Redmi Note 3 using Tapatalk
ShadowLeaf said:
By this, can I charge my mobile faster?
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
Yes if you are on a qc enabled kernel
Kenzo Charge Control V1.1 works fine on Radon V2.5.1. Thank you.
Hey @Umang96 I would like to know what are the benefits of limiting the charging rate? Better battery life? I want to understand what's the use of the app-
Decreasing charge rate than what's set by default is not a very wise thing to do.
Xiaomi set 2A as the default max allowed input charge, also hardware is also limited to that, that's the reason your device charges quickly from 0-35%. After it slows down as current in battery has also increased so overall Potential difference has decreased which results in long hours of charging.
Decreasing charge rate is not logical as it would not allow to charge efficiently after a certain period time when say when you reach 90%. As the max current is now capped at lower rates so less charge will go inside the battery and thus making it difficult for the charger to charge. Tweaking what's already set to the optimal settings is not a good idea. Xiaomi did what it could to charge this humongous battery.
But in the end it's the call of the users
rodsayd said:
Hey @Umang96 I would like to know what are the benefits of limiting the charging rate? Better battery life? I want to understand what's the use of the app-
Click to expand...
Click to collapse
I don't know, some users fear high charging rates or heat, users like to change charge rate, thats why I made the app, personally I use default 2A only.
This thread seems to attract more criticism than support, I just made the app for user demands, I don't even use it myself and I don't even get anything by it, I didn't make this thread to attract free criticism and spoil my day, I just tried to contribute something for some users who wanted charge rate control. I don't want to continue this now, link will still stay in op if anyone needs it, thread closed.
Can i use it for miui ??
what if my phone blasts ?
what is the safe charge rate ?
jenebarve11 said:
what if my phone blasts ?
what is the safe charge rate ?
Click to expand...
Click to collapse
Don't cross 2000 ... And dont worry ur phone want blast.. if its too hot then it will get automatically switch off..!!
panu09 said:
Don't cross 2000 ... And dont worry ur phone want blast.. if its too hot then it will get automatically switch off..!!
Click to expand...
Click to collapse
Actually i am using 2400 mah and if using 2400 is hazardous then what's the point of using that feature in the kernel ?
jeneb11 said:
Actually i am using 2400 mah and if using 2400 is hazardous then what's the point of using that feature in the kernel ?
Click to expand...
Click to collapse
It is recommended to not cross 2200... Try at ur risk... But i guess it doesn't make actually a difference in charging time...so be careful..!!
Official LineageOS14.1 0131can't work,fc…
Chris_Wang said:
Official LineageOS14.1 0131can't work,fc…
Click to expand...
Click to collapse
same here NOS
@Umang96 any way to fix it?
Not asop
Its asop
??
I too lazy to check what you write
Thx for this great app
Related
Original thread for Nexus 6P is located here:
http://forum.xda-developers.com/nex...t/xthermal-mod-fast-charging-cpu-gpu-t3433784
Hi Guys,
I'm back with the Xthermal Mod.
But this time it is for Nexus 5x.
Introduction:
Nexus 5x is one of the best handsets we have now. No doubts about that.
Nexus 5x has also got one of the best Fast Charging.
But why I always get around 800-1100 mA current while charging?
Max to max I get 1400-1500 mA current.
Is this the best fast charging I can get?
Then I opened my thermal engine file and started working on it.
Goal:
Xthermal_Fast_Charge: Here I tried to boost my charging current/speed while keeping rest values to their default.
Xthermal_Performance: Here I tried to boost my charging current/speed + Same basic CPU & GPU tweaks are also applied.
Also tested with roms based on "N" aka Android 7.x.
Downloads:
Links for Marshmallow and for Nougat: See the attachments.
How to apply:
1. Download the zip
2. Reboot to TWRP recovery
3. Flash the zip and reboot.
Wait let it settle a bit...
Now check the difference using Ampere app...
Credits:
Google
Notepad++
@keaheng for testing
Note to mods: Please kick it to related section if I missed it.
Reserved...
Thank you, I'll try out and give feedback. Are this values modifying the governor? I'm on elemental x with silver fish profile. And can you specify what should we expect from it? More battery? More performance? Sounds promising
Edgarngg said:
Thank you, I'll try out and give feedback. Are this values modifying the governor? I'm on elemental x with silver fish profile. And can you specify what should we expect from it? More battery? More performance? Sounds promising
Click to expand...
Click to collapse
Faster charging...
more better cpu and gpu performance in day to day tasks...
This is purely thermal engine based mod which works on tweaking the initial throttling values so that we can delay throttling a bit ...
Charges faster, thanks....
Works like a charm! Thanks for the work man! Much appreciated!
Never saw a mod like this lol, will try thanks
TW1ST3D1NS4N3 said:
Works like a charm! Thanks for the work man! Much appreciated!
Click to expand...
Click to collapse
I have flashed all 3 zips and no matter which one is flashed the script always reads inside of TWRP "Back To Stock"?
Cool tweaks, pretty similar to the thermal throttling tweaks detailed in this thread months ago: http://forum.xda-developers.com/nexus-5x/general/guide-thermal-throttle-tweaking-t3395681
I'm not too wild about the battery temperature tweak here. Li-Ion batteries shouldn't really exceed 45 Celsius when being charged. The problem with these batteries is that the hotter they get, the worse rate they charge at. On top of this, higher temps reduce the battery's overall lifespan. Bottom Line: The temperature threshold for the battery in our phones is there for a reason.
Thanks for posting. I am currently on ElementalX with various over clocking enabled. Will this interfere with that in anyways or cause instability?
this changes whatever changes i may have already done to thermal.conf?
---------- Post added at 12:13 PM ---------- Previous post was at 12:00 PM ----------
another question when i flashed the 5x xthermal performance fast charge is it supposed to say back to stock ?
TW1ST3D1NS4N3 said:
I have flashed all 3 zips and no matter which one is flashed the script always reads inside of TWRP "Back To Stock"?
Click to expand...
Click to collapse
No issues at all as files inside the zips are correct...
Might be copy paste issue ... will check the same...
Thx for reporting...
Edit: just checked...
Forgot to modify updater script lol...
Will edit it in evening... rtnw at office
How? I get 3000 without doing anything
Can this affect to battery life?
axiel7 said:
Can this affect to battery life?
Click to expand...
Click to collapse
I haven't noticed anything...Been using for a couple days now
Wich one makes the phone charging faster (I want the fastest)
Without Rules said:
Wich one makes the phone charging faster (I want the fastest)
Click to expand...
Click to collapse
Read the OP
Confirming this definitely works... I'm impressed truthfully. My charging speed was always crap, 300 mah with the 2.5 charger from Google, now it's 1750~ mah
Because I'm not sure, say I have a custom kernel, will this alter or negatively affect anything I already have going on? Or does this just modify only the charging?
Sent from my Nexus 5X using XDA-Developers mobile app
Does this tweak work alongside the Thermal Throttling Tweak by Razorless. Lost my charging brick and using an iPad one and the speeds never get to what it used to be, would love to try this out. Thanks
now for Mi 5s Plus miui 8.2
http://en.miui.com/download-315.html#464
Thanks man i try later and comment!
Hi fiskerc,
Look at you PM on the en.mi.com forum
Concerning the 8.2.2.0 version, here are the 3 problems I did experience after a Fastboot flash, which resets the phone completely, so it doesn't get "cleaner" than that...
#1 : Bluetooth problem : even if you cahnge the name of the device in Bluetooth settings, the name stays on default ;
#2 : Bluetooth problem : if I make a phone call while Waze is running, as soon as Waze gives a street indication, phone speaker is shut down... can't hear my caller anymore ; have to check if it happens with Waze only or with other apps also ;
#3 : Battery problem : it seems that battery drain is pretty high ;
#4 : Charge problem : I tried with at least 4 different QC 3.0 compatible chargers (and different USB-C cables too !) : I never get charging power over 1.5A (1510 to be precise). On really rare occasions I get 2680mAh (which is what I am supposed to get) but that is absolutely not consistent...
So all in all : trying 7.3.23 at the moment. If that does not fit, I'll roll back to 8.0.4.0. Or maybe to Lineage or RR (if RR boots... haven't tested it so far).
Regards.
No issues here with 8.2.2.0 taken as an OTA update. If anything battery life and performance have improved. Also recieved Google assistant today which I'm enjoying playing with.
Sent from my MI 5s Plus using Tapatalk
I think the global 8.2.2 does not bring anything significant the opposite but cons that pros
http://bigota.d.miui.com/V8.0.4.0.MBGMIDI/miui_MI5SPlusGlobal_V8.0.4.0.MBGMIDI_58853c4577_6.0.zip
8.0.4.0 now available
I have 8.2.2.0 can use 8.0.4 ? Because cannot call have problems with this phone
I personally would be hesitant to download a version of the ROM not from OTA or from the official site. I've read about a few fake ROMs out there.
As for having call problems, what sort of problems are you having? not able to connect to 2G/3G/4G? If so, what band does your operator work on and is that band open?
Is it based on marshmallow or nougat?
NexusPenguin said:
Hi fiskerc,
Look at you PM on the en.mi.com forum
Concerning the 8.2.2.0 version, here are the 3 problems I did experience after a Fastboot flash, which resets the phone completely, so it doesn't get "cleaner" than that...
#1 : Bluetooth problem : even if you cahnge the name of the device in Bluetooth settings, the name stays on default ;
#2 : Bluetooth problem : if I make a phone call while Waze is running, as soon as Waze gives a street indication, phone speaker is shut down... can't hear my caller anymore ; have to check if it happens with Waze only or with other apps also ;
#3 : Battery problem : it seems that battery drain is pretty high ;
#4 : Charge problem : I tried with at least 4 different QC 3.0 compatible chargers (and different USB-C cables too !) : I never get charging power over 1.5A (1510 to be precise). On really rare occasions I get 2680mAh (which is what I am supposed to get) but that is absolutely not consistent...
So all in all : trying 7.3.23 at the moment. If that does not fit, I'll roll back to 8.0.4.0. Or maybe to Lineage or RR (if RR boots... haven't tested it so far).
Regards.
Click to expand...
Click to collapse
With respect to problem number 3, I am not seeing that high of a battery drain. max 470 mA while listening to music over bluetooth with wifi enabled and screen brightness at max, averaging 200 mA. But I don't have my phone screen at max most of the time. I usually have it just below half which then maxes out around 370 mA. You should check your settings. Which background apps do you have running while seeing high battery drain? I tend to kill off apps that I don't use and try not to install too much that is in an "always running" state such as facebook. On my old phone, uninstalling facebook gave my phone an extra 4-6 hours of battery.
As for point number 4, 1.5A is roughly what you should be getting if it is using 12V. Once the battery hits 80% full, you should be switching to a lower voltage (9V or 5V depending) at which point the current should increase.
bokeh?
bmg002 said:
With respect to problem number 3, I am not seeing that high of a battery drain. max 470 mA while listening to music over bluetooth with wifi enabled and screen brightness at max, averaging 200 mA. But I don't have my phone screen at max most of the time. I usually have it just below half which then maxes out around 370 mA. You should check your settings. Which background apps do you have running while seeing high battery drain? I tend to kill off apps that I don't use and try not to install too much that is in an "always running" state such as facebook. On my old phone, uninstalling facebook gave my phone an extra 4-6 hours of battery.
As for point number 4, 1.5A is roughly what you should be getting if it is using 12V. Once the battery hits 80% full, you should be switching to a lower voltage (9V or 5V depending) at which point the current should increase.
Click to expand...
Click to collapse
hi,
what about the [email protected], does this update having the bokeh function in camera apps?
im currently at 8.0.6.0 MBGCNDH - and im not getting any OTA notification for this 8.2.2.2
madknownz said:
hi,
what about the [email protected], does this update having the bokeh function in camera apps?
im currently at 8.0.6.0 MBGCNDH - and im not getting any OTA notification for this 8.2.2.2
Click to expand...
Click to collapse
Version 8.0.6.0 is an unofficial version so it will not get any OTA from my understanding. You will need to flash 8.0.4.0 or 8.2.2.0 or wait for 9 which should be out sometime this month or next according to what I have been reading.
But yes, 8.0.4.0 and 8.2.2.0 both have bokeh from my understanding. 8.2.2.0 does for sure (as that is what I am on), but it only applies when you are using the Stereo photo mode.
bmg002 said:
Version 8.0.6.0 is an unofficial version so it will not get any OTA from my understanding. You will need to flash 8.0.4.0 or 8.2.2.0 or wait for 9 which should be out sometime this month or next according to what I have been reading.
But yes, 8.0.4.0 and 8.2.2.0 both have bokeh from my understanding. 8.2.2.0 does for sure (as that is what I am on), but it only applies when you are using the Stereo photo mode.
Click to expand...
Click to collapse
Hi guys ..just bought a mi5s plus for my wife it's a first Xiaomi device for me....I'm currently on oneplus 3t...
A little confused with the official ROM...
Wich ROM is the latest global official...8.0.4.0 or 8.2.2.0??..
I'm currently on the 8.0.4.0..im trying to found a link for the 8.2.2.0 without success...
8.0.4.0 is the current "official" ROM. 8.2.2.0 was up short term, but it was buggy so it got pulled. version 9.x.x.x is supposed to come out either this month or next if the rumors are to be believed.
You can always put a custom ROM on, but you'll need to unlock the bootloader first.
Hello! My Mi5s Plus came with 8.2.2.0 Global.
I found something very annoying. Whenever i touch the fingerprint scanner, even by mistake, the screen wakes up. Is there any possibility to disable this option?
Thanks!
Miui 8.5.2 is out. How to get the beta version of miui 9?
It's amazing how much we actually use our phones in a given day, especially when we watch "videos"! Rate this thread to express how many hours of screen-on time you can get on the Xiaomi Mi Note 2 before depleting the battery.
Then, drop a comment if you have anything to add!
no 1??
realista87 said:
no 1??
Click to expand...
Click to collapse
The screen on time for me is around 8 hours at max, that if do not listen to a lot of music in the background.
Miui can give that battery performance, but it's hard for it to achieve it.
Instead, we have some really nice custom roms and kernel that give that and even more.
I could get 10 hours and a half of screen on time on miuipro with akt profiles apk and some tweaks made with lspeed/hebf (i don't remember which one but they are somewhat the same).
In a normal day , you can achieve 5-7 hours of SOT .
thank u very much.... maybe i am going to buy it and use it with custom rom.... something like resurrection remix or similar high featured roms
can the qc 3.0 feature work also with custom roms?
realista87 said:
thank u very much.... maybe i am going to buy it and use it with custom rom.... something like resurrection remix or similar high featured roms
can the qc 3.0 feature work also with custom roms?
Click to expand...
Click to collapse
Of course. Maybe not all the roms have it, but the official ones, they have qc 3.0 definitely.
5-7.5 hours depending on usage/rom/kernel.
alexmanu1 said:
Of course. Maybe not all the roms have it, but the official ones, they have qc 3.0 definitely.
Click to expand...
Click to collapse
Hello. I would like to acquire a Mi Note 2 and I would like to ask you some questions about it, could you give me a private message?
Introduction
Hello everyone! Some of you might recognize me from the Xthermal Fast Charge thread, where I had earlier created and posted unified zips for modifying the stock thermal config file on the Nexus 6P, combining the work of two different mods, namely CTTMod and Xthermal Fast Charge Mod.
Since I was earlier maintaining my unified zips in the Xthermal Fast Charge Mod thread, I have now decided to create a separate thread for them since there is still interest and I don't want to unnecessarily clutter somebody else's thread. Let's get straight to it then!
Detailed Information
CTTMod - Thread Link
When CTTMod was initially released, it changed certain values in Nexus 6P's stock thermal file to raise the temperatures at which the phone would start to use thermal throttling. This change led to an increased overall performance and the phone could be used for a longer period of time without any crippling of performance due to thermal throttling, at the cost of heat. Therefore, after using this mod, the phone would feel slightly warmer as compared to how it would've felt if this mod had not been used, but with higher sustained performance.
Xthermal Fast Charge Mod - Thread Link
When Xthermal Fast Charge Mod was initially released, it also changed certain values in Nexus 6P's stock thermal file to raise the temperatures which prevented the charging current to exceed a certain value (usually ~1500 mAh to 1700 mAh) even though the stock OEM charger was capable of delivering a current upto 3000 mAh. This change led to an increased average current drawn (~2600 mAh to 2800 mAh), thereby leading to a decrease in the time taken by the phone to charge, again, at the cost of heat. Thus, a faster fast charge.
Unified Thermal Mod
Since both the base mods target the same stock thermal file, they can't be used together and using one would override the changes done by the other. In other words, one can only use CTTMod or the Xthermal Fast Charge Mod, exclusively. My unified thermal mod provides a workaround for this by taking the best from both of the above mentioned mods and combining their changes into one file, packaged into a Magisk module/TWRP flashable zip, so that one can take the advantage of both, increased performance due to an increase in thermal throttling temperature limits as well as a faster fast charge.
Compatibility
Device(s)
Nexus 6P
ROM(s)
All ROMs
Android Version(s)
Android Marshmallow 6.x.x
Android Nougat 7.x.x
Android Oreo 8.x.x
Android Pie 9.x.x
Android Q 10.x.x
Download
Direct Link
Important Read-Me Points
Installation/Uninstallation
In case you wish to install the modified libraries directly in the system partition and not as a Magisk module, then add "sysover" (without the quotes) to the zip name and flash it via TWRP.
The zip will abort the installation if you try to flash it on any other device except the Nexus 6P and if you aren't running Android Marshmallow, Nougat, Oreo, Pie or Q.
The zip auto-detects your Android version and installs the correct modified thermal configuration file automatically.
To uninstall the mod, just reflash the zip via TWRP and it will undo any changes it did (whether installed as a Magisk module or directly in the system partition).
General
The mod only works with the stock OEM charger. If you're using a third party charger (irrespective of the fact whether it supports Qualcomm QuickCharge or any other fast charge capability) this mod won't work.
The lower your battery percentage is, the faster your phone will charge, i.e. as the battery charge percentage increases, the current drawn by the phone will decrease. This is stock behaviour.
The mod doesn't change the USB charge current. That is controlled by the kernel.
Regarding the thermal driver, it is preferred that you enable msm_thermal and disable core_control for effective results. However, if doing that causes issues for you (for example, cores don't come online automatically after going offline while using msm_thermal), then disable msm_thermal and enable core_control via a kernel tuning app, like EX Kernel Manager.
If possible, avoid playing games/use performance heavy apps while the phone is charging. Doing so won't cause any issues, but it is preferred not to do so while the phone is on charge.
Disclaimers
I am not the original developer of the base mods used, i.e. CTTMod and Xthermal Fast Charge Mod. I merely combined the two since they couldn't be used together. I take no credit for the original work. Please direct all your thanks and/or donations towards @Robshr and @ravinder0003, the original developers of the mods.
You are doing this at your own risk. I am not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed. Please do some research if you are unsure of how to go about something.
Thanks To
@Robshr, for his work on the original CTTMod
@ravinder0003, for his work on the original Xthermal Fast Charge Mod
@Zackptg5, for Unity Installer and all the work he's ever done for the community
@topjohnwu, for Magisk and all the work he's ever done for the community
All of you guys for viewing this thread and using the mod
Changelog
v1.0 - Initial release for Magisk v14.0
v1.1 - Updated to include changes from CTTMod's latest release for Android 8.x Oreo
v2.0 - Update for Magisk v15.0
v3.0 - Update for Magisk v17.0
v4.0 - Updated the zip base to the Unity Installer template
v5.0 - Added support for Android 10, updated the base template to Unity v4.4 and EOL update
OP Information
Thread Update Information
Created: September 15, 2017
Last Updated: September 29, 2019
Source Code
GitHub
@shadowstep
So you are here...
Nice mods work great
phantom146 said:
@shadowstep
So you are here...
Click to expand...
Click to collapse
Haha! I'm actually still there, but decided to keep this going even though I don't have the device anymore, but have a few testers who are available to help, so why not!
adame09 said:
Nice mods work great
Click to expand...
Click to collapse
Thank you!
Thanks for this mod! Working great on Oreo (superXE Rom with ElementalX).
Working perfect here too. Thank you
Sent from my Nexus 6P using Tapatalk
@shadowstep I would really love to try this but unfortunately, I live in a tropical country where we have above normal temperatures. The external temperature is hot enough, and if I did this, I'm risking global warming with my angler
phantom146 said:
@shadowstep I would really love to try this but unfortunately, I live in a tropical country where we have above normal temperatures. The external temperature is hot enough, and if I did this, I'm risking global warming with my angler
Click to expand...
Click to collapse
Haha, come on now, I'm not far from the Philippines (I'm in India) and I gave it a shot. Jokes apart, I know what you mean man. For us, in summers especially, this might not be the best mod to use on a daily basis, more so if the usage is heavy. In winters, however, it's a different story entirely, and I found this mod really helpful.
shadowstep said:
Haha, come on now, I'm not far from the Philippines (I'm in India) and I gave it a shot. Jokes apart, I know what you mean man. For us, in summers especially, this might not be the best mod to use on a daily basis, more so if the usage is heavy. In winters, however, it's a different story entirely, and I found this mod really helpful.
Click to expand...
Click to collapse
Back at you, we don't have winter :laugh:
Right now i'm not gonna bake my already half-baked phone and almost dying battery. I'd stay off of thermal mod for now but im really eager to try cttmod out.
phantom146 said:
Back at you, we don't have winter :laugh:
Right now i'm not gonna bake my already half-baked phone and almost dying battery. I'd stay off of thermal mod for now but im really eager to try cttmod out.
Click to expand...
Click to collapse
Haha, oh we do, chilly ones!
Also, you might want to consider a battery replacement if you plan on keeping your 6P for some time. I got it done from the Huawei Service Centre in my area, and the original one didn't cost a bomb at all. After the change, my SOT started averaging 4.5-5 hours (up from 2.5-3 hours).
shadowstep said:
Haha, oh we do, chilly ones!
Also, you might want to consider a battery replacement if you plan on keeping your 6P for some time. I got it done from the Huawei Service Centre in my area, and the original one didn't cost a bomb at all. After the change, my SOT started averaging 4.5-5 hours (up from 2.5-3 hours).
Click to expand...
Click to collapse
Yeah i've really considerd replacing it and I've heard its quite cheap. Though last april or so I've heard somebody talking about battery replacement on PH and huawei said that they're running out of "stock" with angler. So I guess I better check it out. I might not be buying anyreplacement sooner or later but I have plans next yr to buy the OP6 or Pixel 2.
phantom146 said:
Yeah i've really considerd replacing it and I've heard its quite cheap. Though last april or so I've heard somebody talking about battery replacement on PH and huawei said that they're running out of "stock" with angler. So I guess I better check it out. I might not be buying anyreplacement sooner or later but I have plans next yr to buy the OP6 or Pixel 2.
Click to expand...
Click to collapse
Yep, like I said before, it's not expensive, so if you manage to get your hands on one, definitely go for a replacement. Hopefully, some are still available and not out of stock. Also, I'm not too keen on Pixels anymore, seeing how comparatively difficult it is for developers to get stuff working on it + they cost a bomb! That's why I went for OnePlus 5. Had Google stuck with the Nexus line-up, I would've never bought anything else to be honest, but well..
shadowstep said:
Yep, like I said before, it's not expensive, so if you manage to get your hands on one, definitely go for a replacement. Hopefully, some are still available and not out of stock. Also, I'm not too keen on Pixels anymore, seeing how comparatively difficult it is for developers to get stuff working on it + they cost a bomb! That's why I went for OnePlus 5. Had Google stuck with the Nexus line-up, I would've never bought anything else to be honest, but well..
Click to expand...
Click to collapse
Yep if only they continued nexus, I'm gonna be fanboy on nexus forever lol. Well im interested at nokia right now as well as android one, hope they get a good community tho
I'm on oreo stock rom but using Elemental kernel, which versión should I use? The Overclocked one or the stock frecuency kernel?
phantom146 said:
Yep if only they continued nexus, I'm gonna be fanboy on nexus forever lol. Well im interested at nokia right now as well as android one, hope they get a good community tho
Click to expand...
Click to collapse
Me too! :highfive: Coming to Nokia, they're definitely upping their game, but I'm not sure about the developer backing it will get vis-à-vis OnePlus; the latter has the best developer backing after Google. Android one is relatively new, so let's see where does it go. The new Mi A1 could be start of something great.
jsecruzvalencia said:
I'm on oreo stock rom but using Elemental kernel, which versión should I use? The Overclocked one or the stock frecuency kernel?
Click to expand...
Click to collapse
If while flashing the kernel, you selected the overclocked frequencies for your cores, then use the overclocked oreo variant of the mod. If you didn't make any changes in the frequency screen/aren't sure if you're overclocked or not, just use the normal oreo variant and you should be good.
I notice higher temperatures as expected.
Actually my N6P reached 44.5C, are we fine?
I am talking about battery temperature
Actually I just answered my question, flashing Oreo stock throttling .zip
Thanks for the mod, no offence.
Have fun, George.
How to know if my kernel is overclocked or not? I am using Flash kernel v2.5
teohguangli said:
How to know if my kernel is overclocked or not? I am using Flash kernel v2.5
Click to expand...
Click to collapse
Not overclocked.
Pipiou211 said:
I notice higher temperatures as expected.
Actually my N6P reached 44.5C, are we fine?
I am talking about battery temperature
Actually I just answered my question, flashing Oreo stock throttling .zip
Thanks for the mod, no offence.
Have fun, George.
Click to expand...
Click to collapse
Yes, that is expected, because the mod increases performance at the cost of heat, so temperatures will be slightly higher as compared to stock. It's been mentioned in the OP as well.
Also, no offence taken, at all. Feel free to use/not use the mod, whatever you feel comfortable with. Thanks for stopping by!
teohguangli said:
How to know if my kernel is overclocked or not? I am using Flash kernel v2.5
Click to expand...
Click to collapse
You can use a kernel manager app like EXKM or Kernel Adiutor to check that. If the maximum CPU frequencies for the little and big cluster are 1708 MHz and 2054 MHz, respectively, then you're running an overclocked kernel. However, if they are 1555 MHz and 1958 MHz, respectively, then you're running a non-overclocked/stock frequency kernel.
I know asking for ETA isn't allowed but could you do a fast charge only version for Oreo? I really dislike the thermal mod but would love to have the fast charge one
Is anyone else missing the fast charging feature of the Poco while using the Pixel Experience CAF ROM? Using the Ampere app, my phone measures a really low charging current compared to that of stock MIUI. Is this an issue on other custom ROMs such as LineageOS? Any replies would be much appreciated.
There is zip that remove thermal mod you can try that. It will increase the speed
Rakibboss said:
There is zip that remove thermal mod you can try that. It will increase the speed
Click to expand...
Click to collapse
Do you have a link to the zip?
morgan757 said:
Do you have a link to the zip?
Click to expand...
Click to collapse
Found on telegram maybe..
https://bit.ly/2u6DhrG
Chrysalis Mod has been removed. I really don't know why. It was a great mod and unlocked the true potential for my poco (else it throttled like hell).
Thankfully I have a backup.
Thank you for creating this topic!
I installed a new ROM (from mod stock to LineageOS) and modules magic, put it at night for charging, and the maximum charge current is 0.5A. Since yesterday I have been looking for the source of the problem, at first I didn’t even believe the solution.
But removing this module, everything began to work fine. 94% of the battery charge and charge current min 1.2A.
Device: Samsung A520F
Solution v.2.0: problem if only in the case of a "Full" version installation. When you select the "Slim" version, everything works fine.