BLU Energy X [HARD BRICKED] - After Flashing Stock ROM - Android Q&A, Help & Troubleshooting

Hi, I have the BLU Energy X, and I had flashed some ZIP mods via TWRP. I decided that I didn't want them, and read somewhere that I had to flash my phone using the stock ROM. I used the ROM from NeedRom here: needrom[.com]/ download/ blu-energy-x-e010q which should be the correct one for my phone. It also shows the . I installed proper drivers and flashed using smartphone flash tool. It completed, and I unplugged my phone and pressed the power button. Nothing happened. No combination of power and volume buttons turn this phone on. I have tried flashing again, and I got the error "BROM ERROR : S_FT_ENABLE_DRAM_FAIL (0xFC0)". My phone does show up in Device Manager when I plug it in, as USB Serial Device (COM6) under the Ports category. Sometimes it will go in a loop of SHowing up then 3-5 seconds disconnecting from PC, then connecting again. Before I flashed I used the format option because I was getting an error, and that was the fix for it. The flash completed successfully. I did not touch the device while it was flashing, or the USB cable. I'm in grade 8 and I get a really allowance, so I couldn't buy this phone for about 8-10 months again, and I really want to avoid that. I am/was rooted, if that helps. Thanks everyone here in advance, and I really hope you guys know how to fix this! Thanks alot

Related

[Q] Goophone i5 (MTK6577) will not turn on after using Flashtools

Hello at all guys, I'm desperately trying to install a new recovery to install new rom, I've done maybe a disaster, the phone will not turn on anymore, when I connect it is not detected (with the usual beeping sound on your computer).
I found online a full backup of a MTK6577 (boot.img, preloads, logo, recovery, etc.) I put all these files and made the procedure of flash with the software flash tools, the operation is completed I came out the green circle all that went well, but the phone will not turn on anymore.
The only strange thing is that I can load it with the power supply, this is because I use a cable that makes you see when you are charge(see attached file),this when there is no charging source will turn off automatically.
I have buyed this phone by this store: ([email protected]@[email protected]/snapshot/[email protected]), I tried to apply for a refund, but they are gone (as usual)
I tried to click on the back button (reset), but there is no button on the inside.
I ask for your help desperately, if there is any possibility of recovery in some way, even opening the phone, otherwise they are thrown money.
Many thanks, i hope you help me.
up, please help me

[Q] No power to Wiko Darkmoon (MT6582) after Recovery Flash attempt

Hey all,
In an attempt to load the custom ROM from http://forum.xda-developers.com/showthread.php?t=2658343 I kinda broke the phone.
Part of the steps is to flash the custom Recovery screen.
In the steps you use the Scatter file that's provided and load that up with the SP FlashTool.
Problem though is that I started to get the error SP FLASH TOOL ERROR : (8038).
I then read that by using MTK Droid Root & Tools, I could create a new Scatter file that would fix the error...
Created the new scatter file and then when I loaded it, I got the Big Green Circle saying everything was cool.
Rebooted the phone and it wouldn't come back on.
Crap.
Tried loading into the Recovery screen using the volume and power button, but nothing shows up on the screen.
Tried plugging it into my Win7 and WinXP computers but neither recognize the device and nothing shows up on the screen to say that it's charging.
Is this phone completely gone or is there something that can be done?
Old thread but somehow connected brand new experience to be documented:
What I just experienced was, after a cancelled attempt of flashing recovery, the phone was off and didn't go back on. I tried fiddling with the buttons and assumed it was bricked. Fortunately I didn't give up too soon. It was only after pressing the on button for a very extended time (>30secs?) that it came back to life. It didn't boot further than Wiko logo, but the key reactions were back to normal concerning reboot, booting recovery and cold start.

BROM ERROR on sp flash tools, HELP!

i have a tecno f8 device, it has MT6589 processor. The phone hanged one time and i forced restart it holding down the power button for about 10secs, unfortunately when the phone restarts, it kept coming on and off, and here is where i think i bricked the phone, the phone's battery was at 10%..i pulled the battery and loaded the cmw recovery plugged in the charger, and i tried reflashing my custom rom (miui v5).. the rom installed completely.. then i went to 'reboot now' from the cmw menu options, and then my phone refused to come on, its just dead, led light wont even come on if i plug the charger, and i cant boot into recovery.
i have been to a number of android developmental blogs trying to solve this issue, i even download the stock firmware and i tried flashing with sp flash tools, but i keep getting various brom errors, the 3149, 5069 no space errors.
can anyone pls help me get my phone back on?

[Q] Lenovo phone bricked itself?

Hi,
I've got Lenovo s650, rooted with a custom rom (MIUI). All was perfect for weeks but few days ago it started randomly going off. Then I noticed that sometimes when I listen to music it crashes (making the music freeze and repeat same note for like 10secs) and shuts down. I thought it could be related to some apps but since I was very busy I didn't do anything about it.
Now today I noticed that my phone suddenly lost network coverage (in area where I always use it). I tried airplane mode on/off but didn't help, so I powered off and thought I will do hard reset when I get back home. However since then the phone is completely dead. Can't get into recovery, if I plug into USB nothing happens, if I take out the battery the red light turns and it goes to "META" mode for few secs (as it's intended to) but I can't download anything into it as I get some DRAM error in Upgrade /flash/ tool.
Funny thing that somehow I was trying all the combinations Volume up/down/both + power and at some point I randomly managed to turn it on so I was gonna make a backup of my stuff but it froze and shut down again. Now nothing works......
Any ideas what happened? :/
Some additional info:
I've got TWRP recovery (however I am unable to re-download it again via flashtool because of DRAM error).
I tried getting into adb but I am not sure if it's possible when the phone is off (tried volume button combinations with battery in and out but nothing).
Also when my phone is with battery and I put it into USB, pc recognizes it as "MTK USB Port", but it keeps disconnecting and reconnecting every 5 seconds. Tried to replace it with adb USB driver but didn't work.
Not having a phone I'll probably give a "Format all" option a shot in flash tool... either gonna brick it forever or fix it..
Edit1: Can't even format due to DRAM error....... :/
Edit2: This is so bizarre... I managed to connect my phone a couple of times in Mediatek preloader mode so the flash tool started flashing the rom, but stopped in a few mins unable to format something because it's protected.
I also managed to turn on the phone a couple of times and tried connecting via adb, but once I grant root permissions, adb shell on my pc cannot find device anymore.
It seems like either a hardware or kernel problem but I know nothing about either of them..
Edit3: I don't know how but I fixed it. Phone seems to be fine for now
Edit4: After 1 hour of working the phone died in exactly the same way.... And so this 6-week old phone will be going to rubbish bin. End of my blog.

No boot on P9000

Hi All,
I have a P9000 it was running a custom ROM with TWRP. I decided to factory reset from with in Android to start fresh but it then went in to a reboot loop, always booting into TWRP recovery. After this I tried reinstalling the ROM, which didn't work. So then i decided to upgrade TWRP which must have failed...
Now i have just a continually rebooting phone with the Elephone logo.
While plugged into my computer upon reboot i get the VCOM device popup for a few seconds, however the USB device is malfunctioning, "The USB device returned an invalid serial number string descriptor." So i am unable to get SP Tools to connect to drop a stock image on it.
Holding power up or down and the power button just cause it to reboot faster.
I'm assuming its done for, but if anyone has any suggestions it would be much appreciated. Thanks
no boot on p9000
Worth a try:
power off, start sp tools flash (stock rom 6), connect to computer and then hold power off and volume up until you get a response from sp (can take a couple of reboots)-> realease buttons and flash.
Worth a try. Might take 2 or 3 trys. I managed to revive my p9000 in this way. I didn't have your vcom problem - not my thing but installing drivers again might help?
sp flash tools: v5.1152 ; stock 6.0: 20160810.
Good luck.

Categories

Resources