Hi,
I'm going crazy with my P710 to bring it back to fully operative.
Problems came out with a full stock status phone, no root, no flash recovery, fully untouched.
After some months of utilization, it became quite slow due to the quite full memory (that is caused by contacts storage explosion) , so I though to reset it by factory reset in settings. Reboot starts normally and it brought me to normal dashboard, no changes.
Then I tried to reset with keys combination, same effect, at boot shows out Android logo of the recovery for about 0.5 sec and then normally boot continues bringing me to dashboard.
Stock recovery doesn't permit any task because is blocked to interacting with LG software client.
Instead to use it I thought to flash directly new Rom and Recovery but to do that I needed root, so I installed Framaroot that gives me root access onthefly, now with dd I performed recovery flashing pushing TWRP and reboot in recovey.
Normal LG recovery comes out, and, again I cannot perform fastboot command.
So I tried to enter in Emergency Mode and flash KDZ image, every steps completed with no errors but at reboot no changes happens.
I also tried chipset flashing using Qualcomm driver procedure for unbricking but device doesn't enter in 9006 mode to raw accessing memory.
After all these tries, phone continue to booting and working quite normally apart some apps crashing, but every modification will lost in next boot.
Can I definitively trash it?
Sorry for my english
Thanks in advance
alebiker said:
Hi,
I'm going crazy with my P710 to bring it back to fully operative.
Problems came out with a full stock status phone, no root, no flash recovery, fully untouched.
After some months of utilization, it became quite slow due to the quite full memory (that is caused by contacts storage explosion) , so I though to reset it by factory reset in settings. Reboot starts normally and it brought me to normal dashboard, no changes.
Then I tried to reset with keys combination, same effect, at boot shows out Android logo of the recovery for about 0.5 sec and then normally boot continues bringing me to dashboard.
Stock recovery doesn't permit any task because is blocked to interacting with LG software client.
Instead to use it I thought to flash directly new Rom and Recovery but to do that I needed root, so I installed Framaroot that gives me root access onthefly, now with dd I performed recovery flashing pushing TWRP and reboot in recovey.
Normal LG recovery comes out, and, again I cannot perform fastboot command.
So I tried to enter in Emergency Mode and flash KDZ image, every steps completed with no errors but at reboot no changes happens.
I also tried chipset flashing using Qualcomm driver procedure for unbricking but device doesn't enter in 9006 mode to raw accessing memory.
After all these tries, phone continue to booting and working quite normally apart some apps crashing, but every modification will lost in next boot.
Can I definitively trash it?
Sorry for my english
Thanks in advance
Click to expand...
Click to collapse
Flashing kdz is way easier than QDL 9008 mode, most of the time copper wire keeps disconnecting.
I suggest you use lg flash tool 2014 and modded kdz by maxx_hr.
After all these tries, phone continue to booting and working quite normally apart some apps crashing, but every modification will lost in next boot.
Click to expand...
Click to collapse
It seems that your /data partition and Internal Storage is damaged. Try wiping both from TWRP 3>Wipe>Chech data and internal storage> wipe or try repairing both.
XDA-00 said:
Flashing kdz is way easier than QDL 9008 mode, most of the time copper wire keeps disconnecting.
I suggest you use lg flash tool 2014 and modded kdz by maxx_hr.
It seems that your /data partition and Internal Storage is damaged. Try wiping both from TWRP 3>Wipe>Chech data and internal storage> wipe or try repairing both.
Click to expand...
Click to collapse
I've tried also KDZ flashing without effect.
And I have only stock recovery; flashing TWRP seems to has any effects, cannot access to it.
There is any other way to check partitions integrity?
alebiker said:
I've tried also KDZ flashing without effect.
And I have only stock recovery; flashing TWRP seems to has any effects, cannot access to it.
There is any other way to check partitions integrity?
Click to expand...
Click to collapse
Did you try KK V20B modded kdz :- http://forum.xda-developers.com/optimus-l3-l5-l7-l9-ii/development/kk-kk-kdz-p710-root-t2950532 (look 2nd post for links)
It should give you cwm, unlocked bootloader, etc.
You can access recovery by pressing and holding both volume buttons first and then hold power button, when Phone vibrates, then release power button then volume keys.
From there flash twrp3 recovery in sdcard (you must have downloaded twrp 3 zip in your sdcard.
When in twrp, go to wipe>advanced>chech internal storage>repair. (you can configure the options)
Post pictures of your Phone.
I will provide my twrp pics in a day or two
XDA-00 said:
Did you try KK V20B modded kdz :- http://forum.xda-developers.com/optimus-l3-l5-l7-l9-ii/development/kk-kk-kdz-p710-root-t2950532 (look 2nd post for links)
It should give you cwm, unlocked bootloader, etc.
You can access recovery by pressing and holding both volume buttons first and then hold power button, when Phone vibrates, then release power button then volume keys.
From there flash twrp3 recovery in sdcard (you must have downloaded twrp 3 zip in your sdcard.
When in twrp, go to wipe>advanced>chech internal storage>repair. (you can configure the options)
Post pictures of your Phone.
I will provide my twrp pics in a day or two
Click to expand...
Click to collapse
I flashed the 20a version of that list, that should push in any case the cwm recovery and unlock bootloader. But volUp + volDown + power combo not brings phone in any special boot and starts normally.
The only recovery that I can access is the stocked one, activated by volUp + home + power at boot. I have attached the photos of that one and what I can do from there.
If I use detect for devices in adb, phone shows in recovery state but due to the non-rooted state I can't do about anything.
Photo in the attachments.
alebiker said:
I flashed the 20a version of that list, that should push in any case the cwm recovery and unlock bootloader. But volUp + volDown + power combo not brings phone in any special boot and starts normally.
The only recovery that I can access is the stocked one, activated by volUp + home + power at boot. I have attached the photos of that one and what I can do from there.
If I use detect for devices in adb, phone shows in recovery state but due to the non-rooted state I can't do about anything.
Photo in the attachments.
Click to expand...
Click to collapse
Try installing gscript, terminal emulator, root explorer as system app if you can get root. The install cwm using riskey95's cwm guide.
I'm not a pro but it is likely that your partitions are damaged.
XDA-00 said:
Try installing gscript, terminal emulator, root explorer as system app if you can get root. The install cwm using riskey95's cwm guide.
I'm not a pro but it is likely that your partitions are damaged.
Click to expand...
Click to collapse
I can getting root by Framaroot method, which push su binary into /system partition. From this I already followed riskey95 guide for pushing cwm recovery; but although dd completes gracefully, at reboot, I can see only Droidboot spinning something for 2sec and then boot starts normally with LG logo. At reboot also SU binary in /system partition are gone.(??)
I thought any change is done in recovery and /system, seems the partitions are gone.
So I reroot device and log the kernel, (log in the attachment) and there are MANY EXT-4 FS ERRORS, but unfortunately, I cannot unmount all partition after boot to check and fix them.
To see if dd really writes something on mmc I did some write integrity test on /data partition and fails if file is greater than ~80mb, maybe because smaller files are maintained in cache?
alebiker said:
I can getting root by Framaroot method, which push su binary into /system partition. From this I already followed riskey95 guide for pushing cwm recovery; but although dd completes gracefully, at reboot, I can see only Droidboot spinning something for 2sec and then boot starts normally with LG logo. At reboot also SU binary in /system partition are gone.(??)
I thought any change is done in recovery and /system, seems the partitions are gone.
So I reroot device and log the kernel, (log in the attachment) and there are MANY EXT-4 FS ERRORS, but unfortunately, I cannot unmount all partition after boot to check and fix them.
To see if dd really writes something on mmc I did some write integrity test on /data partition and fails if file is greater than ~80mb, maybe because smaller files are maintained in cache?
Click to expand...
Click to collapse
Can you give details about all partition (sizes,etc). You can use foldermount to view sizes of all partitions.
You can try to boot the rom without sdcard. See if it makes any difference.
You should talk to neutrondev or weritos about the dmesg.log
XDA-00 said:
Can you give details about all partition (sizes,etc). You can use foldermount to view sizes of all partitions.
You can try to boot the rom without sdcard. See if it makes any difference.
You should talk to neutrondev or weritos about the dmesg.log
Click to expand...
Click to collapse
Here the df and mount logs.
alebiker said:
Here the df and mount logs.
Click to expand...
Click to collapse
Partition sizes look OK.
Try flashing custom kernel and try again. If you are on stock.
Sorry man. I can't help any further. I haven't had any problem like this before.
XDA-00 said:
Partition sizes look OK.
Try flashing custom kernel and try again. If you are on stock.
Click to expand...
Click to collapse
Custom kernel is flashed inside ROM during KDZ flashing right? But KDZ procedure doesn't works with any image.
Probably the flashing chip is fried.
alebiker said:
Custom kernel is flashed inside ROM during KDZ flashing right? But KDZ procedure doesn't works with any image.
Probably the flashing chip is fried.
Click to expand...
Click to collapse
Nope. U have to flash via adb or recovery.
One last chance is to try the fullflash.bin file in neutrondev's hard brick guide.
Or flash v20c kdz of p710.
XDA-00 said:
Nope. U have to flash via adb or recovery.
One last chance is to try the fullflash.bin file in neutrondev's hard brick guide.
Or flash v20c kdz of p710.
Click to expand...
Click to collapse
KDZ flashing doesn't work with any image and hard brick procedure stops between steps 4 and 5 where eMMC doesn't enter in Q9006 mode so I can't proceed with partitions restore..
Related
Update:
I was able to use this method to root the new ICS update. The thread has been edited accordingly.
----------------------------------------------
I was unable to find a single thread that detailed how to root the stock T-Mobile Springboard firmware and keep the boot and recovery partitions intact to allow future updates, so I have consolidated information from other threads and posts, as well as adding a little myself. Full credit goes to the users and thread OP's referenced in the post links below.
The usual warnings apply: Under no circumstances should anyone do this to their device. You are likely to brick your device and render it completey unusable. In addition, you will void your warantee with T-Mobile. So you will have an out-of-warantee brick instead of a nice, functional tablet. Turn back now while there is still time.
Before you begin, I obviously did this to my device without any problems. My device is running full stock T-Mobile Springboard firmware with the following:
Android version: 4.0.3
Baseband version: 314007
Kernel version: 3.0.8
Build number: S7-303uV100R002C201B035
I do not know if it will work on a device with any other version of the firmware. The following also assumes that you have fastboot and ADB installed and functional on your computer.
In describing how to boot into fastboot and recovery modes below, the description of the volume buttons is how they are while in portrait mode in Honeycomb....as this is where I first used this method. In other words, the volume button closer to the power button is volume up and the other volume button is volume down.
1. Download the CWM Recovery image from this post:
http://forum.xda-developers.com/showpost.php?p=23601045&postcount=7
2. Download CWM-SuperSU-v0.95.zip from this post:
http://forum.xda-developers.com/showpost.php?p=27678611&postcount=22
3. Copy the CWM-SuperSU-v0.95.zip file to an sdcard and put the card in your device.
4. Flash the CWM recovery image to your first recovery partition ONLY:
a.) Boot into fastboot by powering down the device and starting it back up by pressing the
volume up and power buttons at the same time. After the device vibrates, release the
power button but keep holding the volume button until it is booted into fastboot.
b.) Once in fastboot, flash the recovery image:
Code:
fastboot flash recovery recovery5.5.0.4.img
5. Press and hold the power key for 10 seconds to reboot the device. It will boot into the
T-mobile firmware.
6. Power down the device in the usual fashion.
7. Boot into recovery by starting the device back up by pressing the volume down and power
buttons at the same time. After the device vibrates, release the power button but keep
holding the volume button until it is booted into CWM Recovery.
8. Choose 'install zip from sdcard' -> 'choose zip from sdcard', then select the
CWM-SuperSU-v0.95.zip file you put on your sdcard above, then confirm installation.
9. Go back to the main menu and select 'reboot system now'. It will boot into the T-Mobile
firmware.
10. Shut the device down again in the usual fashion, then restart normally and boot into the
T-Mobile firmware again.
11. Now you need to get your stock recovery partition back and get rid of CWM recovery.
There are two copies of the stock recovery- one on each 'recovery' and 'recovery2'. You can
get back to stock recovery by extracting an image from 'recovery2' and flashing it back to
'recovery'. The following (using adb from your computer) will dump the image from recovery2
to your sdcard:
Code:
adb shell
su
dd if=/dev/block/mmcblk0p18 of=/mnt/sdcard2/recovery.img
12. Take the sd card out of your device and copy this file back to your computer, then flash the
first recovery partition with this image as in step 4b above, but with your new recovery.img file.
You are now rooted and your recovery partitions are returned to stock.
Once you are rooted, if you would like to remove some of the T-Mobile bloatware note that the apk files are not in the usual location (/system/app). I found them tucked away in the following directory:
/data/cust/app
Of course, you will need an app like Root Explorer to get to them and delete them...or you can just use adb. I deleted several of the apk files in that directory, rebooted, and everything is working just fine...with less bloatware.
Also, be aware that any changes you make will be permanent. I tried hard reseting the device through the usual android settings menu security method, and I kept root and all of my deleted bloatware was still gone after it finished and rebooted. There does not appear to be a way to get all of your stock stuff back once you start deleting things...so make backups of files before you delete them in case removing them causes unexpected consequences.
Just to add another bit of information - a list of what I believe are the internal partitions and their locations appears below. I got this from the output from 'cat /proc/partitions' and 'mount', as well as further inspection of the stock recovery image that I extracted from my device. As we don't have a functional CWM Recovery, and I am not sure that I would use any version that was built for the Mediapad (i.e. non-Springboard) for backup and restoring, this list should give Springboard users a way to back up their devices. Using the 'dd' command as in the coding box at the bottom of the OP for each of the paritions should result in a partition image stored out on the sdcard. Fastboot then should be able to flash these 'backed up' images back to the device as in step 4b of the OP...with the correct partition names and backup files substituted of course. I did do this for the recovery partition as I detailed in the OP, but have not tried it for the rest of the partitions.
Code:
/misc emmc /dev/block/mmcblk0p14
/vrcb emmc /dev/block/mmcblk0p16
/recovery emmc /dev/block/mmcblk0p17
/recovery2 emmc /dev/block/mmcblk0p18
/boot emmc /dev/block/mmcblk0p19
/system ext4 /dev/block/mmcblk0p20
/cache ext4 /dev/block/mmcblk0p22
/cust ext4 /dev/block/mmcblk0p15
/data ext4 /dev/block/mmcblk0p27
/tmpdata ext4 /dev/block/mmcblk0p23
/persist ext4 /dev/block/mmcblk0p21
/tombstones ext4 /dev/block/mmcblk0p24
/firmware ext4 /dev/block/mmcblk0p1
Thanks
Many ty's for this.
Thanks you help me rooted my Springboard. Have you try the MediaPad Phone app can we use the tablet for calling? :good:
Do I have to do step 11 ?
Sent from my SpringBoard using XDA Premium App
---------- Post added at 06:11 PM ---------- Previous post was at 05:49 PM ----------
robkaos said:
Do I have to do step 11 ?
Sent from my SpringBoard using XDA Premium App
Click to expand...
Click to collapse
Also can I do it without PC?
Sent from my SpringBoard using XDA Premium App
Can I use the recovery image from the update that is still on my sd card,what is the difference between the I've springboard .rar, and the su files
Sent from my SpringBoard using XDA Premium App
robkaos said:
Do I have to do step 11 ?
......
Also can I do it without PC?
Click to expand...
Click to collapse
If you do not return your recovery partition to stock, then you will not be able to install future firmware updates from T-Mobile as their updates rely on the stock recovery. So no, you don't have to return your recovery partition to stock, but if you don't you will not be able to install future T-Mobile updates. As far as doing this without a computer - you can use a terminal emulator on your Springboard to create the recovery image from 'recovery2'....the commands should be the same. However, you need to fastboot flash that image back to 'recovery', which you must do from your computer with your device in fastboot mode.
robkaos said:
Can I use the recovery image from the update that is still on my sd card....
Click to expand...
Click to collapse
Yes, if you extract the recovery image from the official T-Mobile update package, you can use this image to flash 'recovery' back to stock when you are done.
Some people have reported that they are unable to boot into CWM recovery if it is flashed only to 'recovery' and not also to 'recovery2'. It is my experience that the device seems to alternate which recovery partition it boots into when you sequentially boot it into recovery mode. When I have CWM on 'recovery' and the stock recovery on 'recovery2', my device will boot into CWM every other time I boot into recovery mode. The other times it boots into the stock recovery. If you can't get CWM recovery to appear when you boot into recovery mode, you could do things a bit different than the instructions. Extract the stock recovery image from the official T-Mobile update package. Store this away on your computer. Then, instead of only flashing 'recovery' with CWM recovery, also flash 'recovery2'. Once you are done rooting the device, use your stored image of the stock recovery to flash 'recovery' and 'recovery2' back to stock.
Originally, I used this method to root Honeycomb. I did not have the T-Mobile update package for Honeycomb and so could not simply extract the stock recovery image from that package. You cannot use the 'dd' command as in step 11 above until you are rooted to dump the image of 'recovery2'. So, without a copy of the update package I could not get an image of my recovery partition without already being rooted. But to root, I have to overwrite my recovery partition with CWM recovery, thereby making it impossible to dump a copy of the stock recovery as I had wiped it out and replaced it with CWM. The solution was to only flash one of the recovery partitions and keep the other one as a backup until the device was rooted and the image could then be extracted.
robkaos said:
...what is the difference between the I've springboard .rar, and the su files
Click to expand...
Click to collapse
Not sure what you are asking here...please clarify.
I haVe found two different root files one su zip and the other is for media pad orange Tahiti ,andspringbord .rar which is the difference?there is not a one click Method like motor defy? My phone wasn't such a problem
Sent from my SpringBoard using XDA Premium App
robkaos said:
I haVe found two different root files one su zip and the other is for media pad orange Tahiti ,andspringbord .rar which is the difference?
Click to expand...
Click to collapse
I don't know about the root files for the Mediapad. I know there is a package that contains the su files and a Windows-based command file that contains a string of adb commands that is supposed to work to root both the Mediapad and the Springboard. I think what you are talking about can be found at either one of these locations:
http://www.modaco.com/topic/354579-...-mediapad-t-mobile-springboard-orange-tahiti/
http://www.gamefront.com/files/22185176/Huawei+MediaPad+ROOT+ICS+Android+4.0.x.rar
I tried to use this, and got a 'premission denied' fail pretty early on. I run Linux on my desktop, so perhaps this works under Windows with the specific Springboard drivers and interface software installed, but it sure does not work in Linux. I came up with my method (or rather consolidated the information for 'my' method from multiple other sources) as a result of having this root method fail for me.
robkaos said:
...there is not a one click Method like motor defy? My phone wasn't such a problem
Click to expand...
Click to collapse
If the files that I linked above work for you, then this is going to be about as close to a 'one-click' method as you can get. Unless you modified it, your Motorola Defy is running Android 2.1 (Eclair). This version of Android can be rooted pretty much just by yelling 'ROOT!' at your phone. There is even an app in the market that can be installed and run on an Android v2.1 device that provides a one-click root without the use of a computer. All of the exploits that were used for these one-click root methods were patched in Android v3+. Pretty much every device needs its own unique root method now, and the only way it is a one-click method is if someone has constructed a command script to execute all of the needed commands for you, as in the linked packages above.
xdajunkman said:
Also, be aware that any changes you make will be permanent. I tried hard reseting the device through the usual android settings menu security method, and I kept root and all of my deleted bloatware was still gone after it finished and rebooted. There does not appear to be a way to get all of your stock stuff back once you start deleting things...so make backups of files before you delete them in case removing them causes unexpected consequences.
Click to expand...
Click to collapse
Just to point out - now that the Springboard ICS update is out, and the zip has been captured and archived - there is a backup of complete stock ICS available. Every single partition is in there including system and cust. So worst case scenario if you bork it by zapping the wrong file in system or cust, you can reflash that partition from the bootloader.
Thanks for the clarification
Sent from my SpringBoard using XDA Premium App
cmstlist said:
Just to point out - now that the Springboard ICS update is out, and the zip has been captured and archived - there is a backup of complete stock ICS available. Every single partition is in there including system and cust. So worst case scenario if you bork it by zapping the wrong file in system or cust, you can reflash that partition from the bootloader.
Click to expand...
Click to collapse
You are, of course, correct. That statement of mine is now outdated...you can delete things to your hearts desire. If you mess something up, just reflash the firmware and start over.
Just finished rooting my MediaPad from t-mobile. I had to install into recovery one and two so now I have no original recovery but I don't really care, I've got the latest Android Ice Cream update beforehand. What usefull apps with root access do I need now? I've got ad free and ROM Toolbox. Was there a phone app that I could use now?
Failed updates and can't recover - PLEASE HELP!
xdajunkman said:
You are, of course, correct. That statement of mine is now outdated...you can delete things to your hearts desire. If you mess something up, just reflash the firmware and start over.
Click to expand...
Click to collapse
Well, unfortunately, I've messed things up. Here's what happened:
1) I received the OTA update and everything went fine with upgrading the my T-mobile Springboard tab to ICS 4.0.3
2) I then got brave and went ahead with rooting and installing SU using the technique described in "Root Stock T-Mobile Springboard" by xdajunkman. That worked fine and I was able to get CWM recovery installed.
3) I then tried to install the [ROM][ICS] [Unofficial] Root-ready Huawei/Springboard International ROM and downloaded the dload folder to my SDCard, etc. I tried using the dload folder with the ulmt.cfg file in it and that failed with a "Installation aborted" message. I then removed that file and tried to go into CWM and tried "Install from zip" approach. Same thing...installation aborted message.
4) So, then I did the next stupid thing...in CWM, I formatted my /system, /data, and /cache. That was a big mistake! I now have officially bricked by tab.
5) I tried to get rid of CWM recovery by extracting the recovery.img file from the stock rom zip file. I fastboot flashed that to the recovery and recovery2 partitions. I then thought, let me try extracting the update.zip from the stock rom zip and put that on the root of my sdcard and tried to install that. No go...it just says, update failed with a big red "FAIL" message in the center.
Any and all help would be immensely appreciated! How can I get back to some sort of working ROM? Please!
Thanks!
knightpawn said:
Well, unfortunately, I've messed things up. Here's what happened:
1) I received the OTA update and everything went fine with upgrading the my T-mobile Springboard tab to ICS 4.0.3
2) I then got brave and went ahead with rooting and installing SU using the technique described in "Root Stock T-Mobile Springboard" by xdajunkman. That worked fine and I was able to get CWM recovery installed.
3) I then tried to install the [ROM][ICS] [Unofficial] Root-ready Huawei/Springboard International ROM and downloaded the dload folder to my SDCard, etc. I tried using the dload folder with the ulmt.cfg file in it and that failed with a "Installation aborted" message. I then removed that file and tried to go into CWM and tried "Install from zip" approach. Same thing...installation aborted message.
4) So, then I did the next stupid thing...in CWM, I formatted my /system, /data, and /cache. That was a big mistake! I now have officially bricked by tab.
5) I tried to get rid of CWM recovery by extracting the recovery.img file from the stock rom zip file. I fastboot flashed that to the recovery and recovery2 partitions. I then thought, let me try extracting the update.zip from the stock rom zip and put that on the root of my sdcard and tried to install that. No go...it just says, update failed with a big red "FAIL" message in the center.
Any and all help would be immensely appreciated! How can I get back to some sort of working ROM? Please!
Thanks!
Click to expand...
Click to collapse
OK so you blanked system, screwed up data and possibly recovery. Cache shouldn't be an issue. Everything else is probably fine.
So from the Springboard ICS update zip, you'll want to flash each of the following from fastboot:
- stock recovery.img to recovery and recovery2
- boot.img just in case that got buggered up
- cust.img
- system.img.ext4
- userdata.img.ext4 (this will probably blank your internal storage but you probably already did that in the process because CWM doesn't know the difference)
At this point, does it boot? If it looks like it might be bootlooping on the animation, give it a good 20-30 minutes before you pronounce that it's not working. Wiping pretty much anything other than cache with CWM is a huge nono... it doesn't work right and it buggers a lot of things up.
Any particular locations for the other files via fastboot?
cmstlist said:
OK so you blanked system, screwed up data and possibly recovery. Cache shouldn't be an issue. Everything else is probably fine.
So from the Springboard ICS update zip, you'll want to flash each of the following from fastboot:
- stock recovery.img to recovery and recovery2
- boot.img just in case that got buggered up
- cust.img
- system.img.ext4
- userdata.img.ext4 (this will probably blank your internal storage but you probably already did that in the process because CWM doesn't know the difference)
At this point, does it boot? If it looks like it might be bootlooping on the animation, give it a good 20-30 minutes before you pronounce that it's not working. Wiping pretty much anything other than cache with CWM is a huge nono... it doesn't work right and it buggers a lot of things up.
Click to expand...
Click to collapse
Wow! Thanks for the help! I unfortunately, don't have my other computer that has the proper drivers installed to recognize the tablet and to run fastboot on. So, I'll try the fix you are suggesting once I get home today. However, in the meantime, I had some questions with regard to where I should flash the other files.
I understand that recovery.img should go to the recovery and recovery2 partitions.
What about the others? Does boot.img go to a particular partition? Effectively, what would the command line look like? (eg fastboot flash boot boot.img?)
Sorry about the newbie questions. I've installed a number of custom ROMs on phones using CWM, but this is a strange beast.
With regard to your question of whether it boots, well, kind of...it does boot to the T-mobile Springboard screen, then it sits there. I will let it sit for 20-30 minutes and see what happens. Will report back...for sure!
Thanks a ton!
[UPDATE]
So, I had a chance to install the TWRP recovery with the CM10 ROM. I loaded the CM10 ROM with the TWRP which installed successfully. I turned the tablet on and let it sit there for about 10 minutes and sure enough, CM10 runs just fine. However, I did notice that I cannot receive any calls. I am able to make calls, but when someone dials my number, it just goes straight to voicemail.
So, now, I'm wondering, if I can get the stock ICS with International ROM running so that I can try to use this thing as a phone, data and texting tab. I'll try what you suggested when I get home as mentioned earlier.
CM10 has too many problems, why would you want to use it?
cmstlist said:
OK so you blanked system, screwed up data and possibly recovery. Cache shouldn't be an issue. Everything else is probably fine.
So from the Springboard ICS update zip, you'll want to flash each of the following from fastboot:
- stock recovery.img to recovery and recovery2
- boot.img just in case that got buggered up
- cust.img
- system.img.ext4
- userdata.img.ext4 (this will probably blank your internal storage but you probably already did that in the process because CWM doesn't know the difference)
At this point, does it boot? If it looks like it might be bootlooping on the animation, give it a good 20-30 minutes before you pronounce that it's not working. Wiping pretty much anything other than cache with CWM is a huge nono... it doesn't work right and it buggers a lot of things up.
Click to expand...
Click to collapse
That worked for me. After playing with vold.fstab I had rendered my Springboard unusable (got the encryption was unsuccessful screen!).
I really wanted to switch the apps installation path to the external sd card but did not succeed.
What am I doing wrong
I have not been able to root my springboard at all. It will go to a black screen that says enter fastboot and it just stays there. When I type to flash the recovery it says it cannot load it. I have adb and fastboot installed...could it be a driver issue? I now know that I am in the correct screen, just can't get this thing rooted. any help would be appreciated thanks.
Well I feel quite stupid. But figured out where I went wrong and for the love of God got my Springboard rooted. *whew*
Hi
I am having some issues with my Xperia Z2 D6502. I am new to rooting, so please bear with me.
I rooted my device following these instructions. All things went smoothly. However next day I started having problems to boot into recovery mode. I have explained my problem here. I tried reinstalling Z2-lockeddualrecovery2.7.154-BETA.installer which I got from the above instructions. It installed successfully but still I couldnt boot into recovery mode. The phone even stopped detecting my SD card, I had to reinsert it each time I would reboot to make it work.
So I followed all the instructions from the scratch again except for the last one which involved flashing pre rooted 5.1.1 stock ROM(flashable_D6502_23.4.A.0.546.zip). I wanted to keep rooted kitkat 4.4.2(I initially,i ..e., before rooting, had 5.1.1 but according to the instructions I had to downgrade it to kitkat) which I obtained as a result of downgrading my Xperia Z2 from 5.1.1.
Now I am facing wifi problems with kitkat. I can connect to the network but internet works extremely slow while it works absolutely fine on other devices. I dont have access to the router as its a common router in my dorm. I tried several solutions which I found on internet involving changing DNS to 8.8.8.8 and changing IP settings to static. None of them had any effect. Is there anything else I could do to resolve this issue?
The main reason I want to keep kikat is that I want to install Xposed on my device for imei changer and android id changer, and I read somewhere that for installing Xposed on kitkat you dont need to flash any zips and just install it like any other app. I didnt flash it on lollipop because of the warnings about getting stuck in bootloop in sony devices and I wasnt sure of how to flash it as the instructions were not very detailed and I am new to it. So do we flash it the same way I flashed 5.1.1 rom, i.e., booting into recovery mode and then selecting install and then selecting the zip I want to install?
I got this link to working modules on sony devices but I cant find imei changer in the list. So even if I installed Xposed, with your help of course, will I be unable to use imei and android id changer?
I read in several places that I should backup my device so that I can restore to the previous state in case I soft brick it or enter a bootloop. What kind of backup is this and how do I take it?(I googled and found Backup TA to take backup but I am not sure if that is the type of backup I am looking for and the instructions in the page are not detailed enough for me as I cant risk my device.)
I have one request, please provide me with detailed steps as I am doing all of it for the first time and am extremely nervous of screwing up my device as it is my only phone and quite expensive too.
Well, my device is rooted, on 5.1.1, and Xposed Works very well, without bootloops, and all Modules that I tried worked very well, by your description I can't figure out what is causing your problems...
stayawake said:
Well, my device is rooted, on 5.1.1, and Xposed Works very well, without bootloops, and all Modules that I tried worked very well, by your description I can't figure out what is causing your problems...
Click to expand...
Click to collapse
I havent tried Xposed on my device yet. Have you tried imei changer and android id changer? If not can you confirm if it works?
Can you please provide me with detailed step on how to install Xposed?
If my device goes into bootloop, will I be able to flash it using stock ROM?
And can you please provide answers regarding taking backup?
berbatov93 said:
I havent tried Xposed on my device yet. Have you tried imei changer and android id changer? If not can you confirm if it works?
Click to expand...
Click to collapse
I didn't tried these two modules.
berbatov93 said:
Can you please provide me with detailed step on how to install Xposed?
Click to expand...
Click to collapse
following the official topic of the module, you will have all the steps to install it, and the version that most fits with your system version
berbatov93 said:
If my device goes into bootloop, will I be able to flash it using stock ROM?
Click to expand...
Click to collapse
If you got a boot loop, you can:
1: Force power off the device by holding volume+ and power button simultaneously, then, you will able to flash via flashtool a new ROM
2: if you have a custom recovery, you can follow the same method to power off, then, power on and access the recovery, where you will be able to flash a zip containing a new system, etc.
berbatov93 said:
And can you please provide answers regarding taking backup?
Click to expand...
Click to collapse
Well, again, using a custom recovery you can make a Backup, the interface is very intuitive and easy to understand.
stayawake said:
I didn't tried these two modules.
Click to expand...
Click to collapse
Can you please try them?
If you got a boot loop, you can:
1: Force power off the device by holding volume+ and power button simultaneously, then, you will able to flash via flashtool a new ROM
2: if you have a custom recovery, you can follow the same method to power off, then, power on and access the recovery, where you will be able to flash a zip containing a new system, etc.
Well, again, using a custom recovery you can make a Backup, the interface is very intuitive and easy to understand.
Click to expand...
Click to collapse
Do we make custom recovery using the backup option we get when we boot into recovery menu?
And how to enter recovery menu without booting into the system? I access it using NDR utils app.
And do I need to flash any recovery zip from the recovery menu if I want to keep it?
berbatov93 said:
Can you please try them?
Do we make custom recovery using the backup option we get when we boot into recovery menu?
And how to enter recovery menu without booting into the system? I access it using NDR utils app.
And do I need to flash any recovery zip from the recovery menu if I want to keep it?
Click to expand...
Click to collapse
If you have Dual recovery, you are already running a custom recovery.
to enter the recovery menu whitout boot the system, you should:
Power On the device, and at the FIRST SONY screen, when the LED flashes, press volume up to enter TWRP
stayawake said:
If you have Dual recovery, you are already running a custom recovery.
to enter the recovery menu whitout boot the system, you should:
Power On the device, and at the FIRST SONY screen, when the LED flashes, press volume up to enter TWRP
Click to expand...
Click to collapse
Volume down for TWRP, volume up goes to the other one, CWM I think? I've never looked!
@berbatov93 you need a bit more patience and to read more things. Forums are awesome because you can get help from people all over the world but it rarely happens in real time.
stayawake said:
If you have Dual recovery, you are already running a custom recovery.
to enter the recovery menu whitout boot the system, you should:
Power On the device, and at the FIRST SONY screen, when the LED flashes, press volume up to enter TWRP
Click to expand...
Click to collapse
Its doesnt enogh to tap once volume up to enter to recovery ,when Sony logo shows he must tap few times volume up until notification led get purple color and phone goes in to recovery.This is procedure for Philzz Touch Recovery.
may i ask you something..did you unmount your memory card before you take it out?
if you want to have lastest version lolipop with root..
downgrade your phone to android lolipop 5.0.1..then follow this step http://forum.xda-developers.com/xperia-z1/general/root-xperia-running-lollipop-lb-ubl-t3123893..
then..
1. install busybox
2. turn on usb debugging and unknown source
3. find lolipop lastest version preroot...copy to your memory card (make sure to unmount it before you put it out) or just put the usb cable
4. install recovery (make sure to get lastest recovery.. can get it on nut.xperia-files.com/)
5. enter recovery then flash lastest pre root lolipop..
6. turn on your phone...
7.Good Luck
TA Partition Backup is for who want to unlock bootloader.. it backup DRM key which important for waranty.
Thank You, i hope this will help you
NamiDragneel said:
may i ask you something..did you unmount your memory card before you take it out?
if you want to have lastest version lolipop with root..
downgrade your phone to android lolipop 5.0.1..then follow this step http://forum.xda-developers.com/xperia-z1/general/root-xperia-running-lollipop-lb-ubl-t3123893..
then..
1. install busybox
2. turn on usb debugging and unknown source
3. find lolipop lastest version preroot...copy to your memory card (make sure to unmount it before you put it out) or just put the usb cable
4. install recovery (make sure to get lastest recovery.. can get it on nut.xperia-files.com/)
5. enter recovery then flash lastest pre root lolipop..
6. turn on your phone...
7.Good Luck
TA Partition Backup is for who want to unlock bootloader.. it backup DRM key which important for waranty.
Thank You, i hope this will help you
Click to expand...
Click to collapse
The DRM keys are unlikely to affect your warranty claim but they do other things including allowing your device to get OTA upgrades.
To unlock your bootloader you have to get an unlock code from Sony, to do that you give them your device details. So if you send it back for warranty and they look it up, I have no idea if they do, they'll see that you have unlocked your bootloader. Or at least got the code to do so, I doubt anyone gets the code without planing on using it.
Those DRM keys play a role in the Sony image processing for both the camera and the Bravia Engine. That is what you lose by unlocking the bootloader, warranty is not the major factor.
Hey
I had the same problem.
So what I did to solve this?
I did a factory reset > flash again flashable_D6502_23.4.A.0.546.zip > wipe dalvik >
And the problem was fixed.
Good luck
Hey guys,
I've had a total of 4 android smartphones during the last years, and I did root all of them and even install diferent ROM's, but on this phone (Honor 7) was kinda diferent.
The root process is way more complex than all the other androids I did root (simply flash a .zip file...) so I've been post-poning this task over and over..
Finally yesterday I gained courage to try out rooting my phone, and while attempting to root my Honor 7, after flashing SuperSU from TWRP, my phone no longer booted.
Stressed as I was, I just told to myself "f*ck it" and formatted the system and I didn't care much if there was a fix without needing to format the system. (but then I realised that I could not find any .img ROM files to flash from TWRP recovery, so basically I did my actions wrong once again)
I followed the tutorial from guidebeats.com which talks about rooting EMUI 4.0 Android 6.0 (I cant post links)
Basically this is the story:
While unlocking the bootloader, even though, the tutorial said the phone would reboot itself after typing "flashboot oem unlock 1234934829" I did a hard reboot (or reset?) holding (VOL+) + Power button and I have the feeling that the bootloader unlock was not 100% done, even if it said it was unlocked. (Phone was working perfectly fine there)
Then I flashed SuperSU, and I could no longer boot. After powering up my phone, after the first splashscreen, the screen would only turn black.
What (I think) I need to now is remove the TWRP recovery, and use the stock one and attempt to install an "update" using (Vol+) + (Vol-) + Power. (please correct me if I'm wrong)
But now there's some issues I got that I'd like some help with:
1- How can I get back to the stock recovery? (NOTE: I currently got no OS installed on my Honor 7, since I formated it)
2- Will I need to lock and unlock my bootloader again (if I want to 'fix' the bootloader unlock?)
3- Where can I get official Honor 7 stock ROM? (would be awesome if there was already the Android 6 stock rom for a clean install)
4- What are the steps on this tool (Honor 7 Multi-Tool) to root my phone?
I need my Honor 7 asap
Sorry for the long post, It's my first time doing a more advanced root and I have all these questions.
Thank you very much for any kind help!
joaomPT said:
Hey guys,
I've had a total of 4 android smartphones during the last years, and I did root all of them and even install diferent ROM's, but on this phone (Honor 7) was kinda diferent.
The root process is way more complex than all the other androids I did root (simply flash a .zip file...) so I've been post-poning this task over and over..
Finally yesterday I gained courage to try out rooting my phone, and while attempting to root my Honor 7, after flashing SuperSU from TWRP, my phone no longer booted.
Stressed as I was, I just told to myself "f*ck it" and formatted the system and I didn't care much if there was a fix without needing to format the system. (but then I realised that I could not find any .img ROM files to flash from TWRP recovery, so basically I did my actions wrong once again)
I followed the tutorial from guidebeats.com which talks about rooting EMUI 4.0 Android 6.0 (I cant post links)
Basically this is the story:
While unlocking the bootloader, even though, the tutorial said the phone would reboot itself after typing "flashboot oem unlock 1234934829" I did a hard reboot (or reset?) holding (VOL+) + Power button and I have the feeling that the bootloader unlock was not 100% done, even if it said it was unlocked. (Phone was working perfectly fine there)
Then I flashed SuperSU, and I could no longer boot. After powering up my phone, after the first splashscreen, the screen would only turn black.
What (I think) I need to now is remove the TWRP recovery, and use the stock one and attempt to install an "update" using (Vol+) + (Vol-) + Power. (please correct me if I'm wrong)
But now there's some issues I got that I'd like some help with:
1- How can I get back to the stock recovery? (NOTE: I currently got no OS installed on my Honor 7, since I formated it)
2- Will I need to lock and unlock my bootloader again (if I want to 'fix' the bootloader unlock?)
3- Where can I get official Honor 7 stock ROM? (would be awesome if there was already the Android 6 stock rom for a clean install)
4- What are the steps on this tool (Honor 7 Multi-Tool) to root my phone?
I need my Honor 7 asap
Sorry for the long post, It's my first time doing a more advanced root and I have all these questions.
Thank you very much for any kind help!
Click to expand...
Click to collapse
As you are already familiar with adb and other stuff so will write a short post for you.
To download latest firmware, head to
http://forum.xda-developers.com/hon...tock-firmware-packages-honor-7-t3448747/page1
Google, download and install Huawei update extractor and open UPDATE.APP in it (obtained after extracting firmware).
You can see all the images. Just extract recovery and boot to platform-tools folder.
Meantime, do the unlocking command again, with
Fastboot OEM unlock xxxxxxxxxxxxxxxx
Followed by fastboot reboot
And press and hold the vol down button again until you reboot in bootloader.
Flash the recovery and boot you extracted using
Fastboot flash recovery recovery.img
Fastboot flash boot boot.img
(I got a habit of extracting and flashing system and Cust using
Fastboot flash system system.img
Fastboot flash Cust Cust.img
But they are not necessary)
Now you are set to try a 3 button update (sometimes it gets stuck so if it's stuck for 15 minutes, try 3 button again).
Please do report back if it comes to life.
To root, just flash twrp and then use SuperSU 2.62 (no other version) and update it later using play store.
Sent from my PLK-L01 using XDA Labs
Hey!
Thank you alot for your reply.
From the link you sent about the firmwares, there are alot of Builds for the L01 (EU) model. Can I simply use the latest from the list or I gotta install 1 by 1 (from older to newer)?
Also, the bootloader unlock thing, is it ok if I wait to do it until I install the stock ROM again? Because I think I don't have the code anymore (Also don't know about IMEI)
Other thing, yesterday before bricking my phone, I tried to re-unlock the bootloader as you said above, but it didnt let me because "it was already unlocked".
I really have no idea if it's 100% unlocked or not.
important thing!
With those ROM's, I still have the right to receive official OTA updates from the HiCare app right?
Thank you again
joaomPT said:
Hey!
Thank you alot for your reply.
From the link you sent about the firmwares, there are alot of Builds for the L01 (EU) model. Can I simply use the latest from the list or I gotta install 1 by 1 (from older to newer)?
Also, the bootloader unlock thing, is it ok if I wait to do it until I install the stock ROM again? Because I think I don't have the code anymore (Also don't know about IMEI)
Other thing, yesterday before bricking my phone, I tried to re-unlock the bootloader as you said above, but it didnt let me because "it was already unlocked".
I really have no idea if it's 100% unlocked or not.
important thing!
With those ROM's, I still have the right to receive official OTA updates from the HiCare app right?
Thank you again
Click to expand...
Click to collapse
Just use B380 as it's the latest full firmware available there.
Unlocking bootloader again was just a precautionary measure (proceed without it and if it is not 100% unlocked and if something goes wrong, we can troubleshoot later, which imo, won't happen)
And yep, if you keep the firmware as it is, but if you flash twrp and root, you will still see the update available in Hicare but will have to install stock recovery again before upgrading. (Nothing else is needed as SuperSU 2.62 gives a systemless root so you only need to flash back stock recovery for an update)
I am not against honor-tool bit it's best to do things manually as it makes you learn stuff and is easy to troubleshoot if something is amiss.
Sent from my PLK-L01 using XDA Labs
muradulislam said:
Just use B380 as it's the latest full firmware available there.
Unlocking bootloader again was just a precautionary measure (proceed without it and if it is not 100% unlocked and if something goes wrong, we can troubleshoot later, which imo, won't happen)
And yep, if you keep the firmware as it is, but if you flash twrp and root, you will still see the update available in Hicare but will have to install stock recovery again before upgrading. (Nothing else is needed as SuperSU 2.62 gives a systemless root so you only need to flash back stock recovery for an update)
I am not against honor-tool bit it's best to do things manually as it makes you learn stuff and is easy to troubleshoot if something is amiss.
Sent from my PLK-L01 using XDA Labs
Click to expand...
Click to collapse
Alright, btw, about the thing you said
"Now you are set to try a 3 button update (sometimes it gets stuck so if it's stuck for 15 minutes, try 3 button again)."
I gotta do that myself with an "update.app" file or what?
Sorry, I missed that part
Cheers!
joaomPT said:
Alright, btw, about the thing you said
"Now you are set to try a 3 button update (sometimes it gets stuck so if it's stuck for 15 minutes, try 3 button again)."
I gotta do that myself with an "update.app" file or what?
Sorry, I missed that part
Cheers!
Click to expand...
Click to collapse
You have to make a dload folder in SD card and copy UPDATE.APP to that folder.
Then just turn off the phone, press and hold power + vol up + vol down until phone boots.
Let go of power but keep others two pressed for 5, 6 sec more. Your phone will boot into recovery and start installing UPDATE.APP
It likes to get stuck at 5% (most reports) but sometimes, somewhere else. If its stuck for 15 minutes on a particular percentage, just press and hold the above three buttons again using the same process.
Multiple tries make it work...
Sent from my PLK-L01 using XDA Labs
muradulislam said:
You have to make a dload folder in SD card and copy UPDATE.APP to that folder.
Then just turn off the phone, press and hold power + vol up + vol down until phone boots.
Let go of power but keep others two pressed for 5, 6 sec more. Your phone will boot into recovery and start installing UPDATE.APP
It likes to get stuck at 5% (most reports) but sometimes, somewhere else. If its stuck for 15 minutes on a particular percentage, just press and hold the above three buttons again using the same process.
Multiple tries make it work...
Sent from my PLK-L01 using XDA Labs
Click to expand...
Click to collapse
Hey man!
Good news, my phone is alive and root is done.
The problem was on the SuperSU that I flashed, it was version 2.71, instead of the one you said » version 2.62 «
I cant thank you enough!! Can I pay you a coffee?
Thank you!
joaomPT said:
Hey man!
Good news, my phone is alive and root is done.
The problem was on the SuperSU that I flashed, it was version 2.71, instead of the one you said �?�» version 2.62 �?�«
I cant thank you enough!! Can I pay you a coffee?
Thank you!
Click to expand...
Click to collapse
That's great... Enjoy your phone and as for coffee, well, let's say, you owe me one and we will leave it at that
Better yet, you can search DigiGoon and pay him for the coffee, he taught me what I told you.
You can find him somewhere in this thread
http://forum.xda-developers.com/honor-5x/help/honor-5x-kiw-ul00-boot-loop-t3449554/page1
Decision is yours
muradulislam said:
That's great... Enjoy your phone and as for coffee, well, let's say, you owe me one and we will leave it at that
Better yet, you can search DigiGoon and pay him for the coffee, he taught me what I told you.
Whichever you like...
Click to expand...
Click to collapse
Alright man, cheers
joaomPT said:
Alright man, cheers
Click to expand...
Click to collapse
Hello
How did you format your phone?
I'm still struggling with going back to Android 5 and EMUI 3.1 since there is no rollback file available. (PLK-AL10, B396) Maybe formatting and installing the old rom could be a solution, like in your case?
tgergo said:
Hello
How did you format your phone?
I'm still struggling with going back to Android 5 and EMUI 3.1 since there is no rollback file available. (PLK-AL10, B396) Maybe formatting and installing the old rom could be a solution, like in your case?
Click to expand...
Click to collapse
Hello.
Do you have unlocked bootloader and TWRP recovery? You can format your phone from TWRP recovery.
I think the only option for you is to get the old ROM img and flash it (starting from 0)
You can dirty-flash (Flash a different ROM with same android version as yours, e.g: flashing custom android 5 ROM over your stock android 5 ROM without factory resetting your phone) but I dont think you can do that from Android 6 to 5.
joaomPT said:
Hello.
Do you have unlocked bootloader and TWRP recovery? You can format your phone from TWRP recovery.
I think the only option for you is to get the old ROM img and flash it (starting from 0)
You can dirty-flash (Flash a different ROM with same android version as yours, e.g: flashing custom android 5 ROM over your stock android 5 ROM without factory resetting your phone) but I dont think you can do that from Android 6 to 5.
Click to expand...
Click to collapse
Yes I have unlocked bootloader and currently not twrp but I can flash it at any time.
The last two paragraphs you wrote are different solutions or the last one is a more detailed explanation of the previous?
I have android 6 so the later method won't work as you said.
But formatting it and flashing a stock android 5 rom - is it that simple? Nobody here suggested this before, however I have been asking for months.
All the phones are empty when they leave the assembly line.
How did you flash the new rom to your formatted phone? Extracted update.app and flashed each file with fastboot? Any issues you faced?
tgergo said:
Yes I have unlocked bootloader and currently not twrp but I can flash it at any time.
The last two paragraphs you wrote are different solutions or the last one is a more detailed explanation of the previous?
I have android 6 so the later method won't work as you said.
But formatting it and flashing a stock android 5 rom - is it that simple? Nobody here suggested this before, however I have been asking for months.
All the phones are empty when they leave the assembly line.
How did you flash the new rom to your formatted phone? Extracted update.app and flashed each file with fastboot? Any issues you faced?
Click to expand...
Click to collapse
From my last 2 paragraphs, the first was a solution, the second was an impossible alternative that I thought it would work.
My issue was that I had a custom recovery but I had no ROM installed, so I had to install the stock recovery and boot (extracting from update.app) and flashing it via fastboot, to afterwards force the update with 3-button method.
-----
What you'll need to do is:
- Flash TWRP
- Wype system, data, cache.. (so that you completely delete your current ROM)
- Extract recovery.img and boot.img from an update.app of an Android 5 ROM you'd like to have (Official ROM for your device model)
- Flash them via fastboot (You'll go back to stock recovery again)
- Shutdown your device
- Create a folder named "dload" on your sdcard and put UPDATE.APP file in it.
- Reboot
- Do the 3-Button update ([Vol+] + [Vol-] + Power)
- If it works, it will auto install
(- If it gets stuck on 5% for over 5/10min, force reboot pressing [Vol+] + Power) and try again the installation
- After installing it will boot normally (first boot takes a while)
NOTE: I'd recommend creading the dload folder before wiping the ROM, because usb didnt work for me afterwards. (It would still work if I was on recovery tho)
>> Remember to make a full system backup before wiping aswell, dont be stupid like me xD (thats why I had to full wipe my system after soft-brick)
Im answering based on what I did and was explained here to me
joaomPT said:
From my last 2 paragraphs, the first was a solution, the second was an impossible alternative that I thought it would work.
My issue was that I had a custom recovery but I had no ROM installed, so I had to install the stock recovery and boot (extracting from update.app) and flashing it via fastboot, to afterwards force the update with 3-button method.
-----
What you'll need to do is:
- Flash TWRP
- Wype system, data, cache.. (so that you completely delete your current ROM)
- Extract recovery.img and boot.img from an update.app of an Android 5 ROM you'd like to have (Official ROM for your device model)
- Flash them via fastboot (You'll go back to stock recovery again)
- Shutdown your device
- Create a folder named "dload" on your sdcard and put UPDATE.APP file in it.
- Reboot
- Do the 3-Button update ([Vol+] + [Vol-] + Power)
- If it works, it will auto install
(- If it gets stuck on 5% for over 5/10min, force reboot pressing [Vol+] + Power) and try again the installation
- After installing it will boot normally (first boot takes a while)
NOTE: I'd recommend creading the dload folder before wiping the ROM, because usb didnt work for me afterwards. (It would still work if I was on recovery tho)
>> Remember to make a full system backup before wiping aswell, dont be stupid like me xD (thats why I had to full wipe my system after soft-brick)
Im answering based on what I did and was explained here to me
Click to expand...
Click to collapse
I'll try... But seems too simple to be true...
joaomPT said:
From my last 2 paragraphs, the first was a solution, the second was an impossible alternative that I thought it would work.
My issue was that I had a custom recovery but I had no ROM installed, so I had to install the stock recovery and boot (extracting from update.app) and flashing it via fastboot, to afterwards force the update with 3-button method.
-----
What you'll need to do is:
- Flash TWRP
- Wype system, data, cache.. (so that you completely delete your current ROM)
- Extract recovery.img and boot.img from an update.app of an Android 5 ROM you'd like to have (Official ROM for your device model)
- Flash them via fastboot (You'll go back to stock recovery again)
- Shutdown your device
- Create a folder named "dload" on your sdcard and put UPDATE.APP file in it.
- Reboot
- Do the 3-Button update ([Vol+] + [Vol-] + Power)
- If it works, it will auto install
(- If it gets stuck on 5% for over 5/10min, force reboot pressing [Vol+] + Power) and try again the installation
- After installing it will boot normally (first boot takes a while)
NOTE: I'd recommend creading the dload folder before wiping the ROM, because usb didnt work for me afterwards. (It would still work if I was on recovery tho)
>> Remember to make a full system backup before wiping aswell, dont be stupid like me xD (thats why I had to full wipe my system after soft-brick)
Im answering based on what I did and was explained here to me
Click to expand...
Click to collapse
Hi again,
I'm doing this OS installation now. It starts fine but stucks at 90%, (I'm trying to install the latest stock ROM which can be downloaded from Huawei site, B220 or221). Did you have the same issue? I waited more than half an hour at 90% but did not go on.
tgergo said:
Hello
How did you format your phone?
I'm still struggling with going back to Android 5 and EMUI 3.1 since there is no rollback file available. (PLK-AL10, B396) Maybe formatting and installing the old rom could be a solution, like in your case?
Click to expand...
Click to collapse
Maybe formatting, Flash stock Android 5 recovery using Honor multitool , and then Flash a Android 5 firmware
Not sure it Will Work without rollback..
Finally, after 2 months of struggling I managed to get back to Android 5 and EMUI 3.1 without a rollback file.
Here is what I did:
0. Download a full ROM you want to install
1. Backup of the current system with Hisuite (everything. Apps, media, contacts, call log, etc.)
2. Flash TWRP recovery with fastboot (start phone in fastboot mode)
3. Wipe (and format!) everything you can with TWRP
4. Extract boot.img and recovery.img from update.app of the new ROM with Huawei Update Extractor
5. Flash boot.img and recovery.img with fastboot.
6. Copy update app to dload folder on SD card, insert into the phone.
7. Restart phone with [VOL+] + [VOL-] + [Power] buttons to force update.
8. The system will be installed from SD card. I had no issues with the installation. First I did not format the phone (just wiped) and it did not work.
9. Restore data from backup.
The only strange thing is that the native app icons look different than my previous lollipop system. Don't know why. They are less colorful. I installed C00B220 for PLK-AL10.
tgergo said:
Finally, after 2 months of struggling I managed to get back to Android 5 and EMUI 3.1 without a rollback file.
Here is what I did:
0. Download a full ROM you want to install
1. Backup of the current system with Hisuite (everything. Apps, media, contacts, call log, etc.)
2. Flash TWRP recovery with fastboot (start phone in fastboot mode)
3. Wipe (and format!) everything you can with TWRP
4. Extract boot.img and recovery.img from update.app of the new ROM with Huawei Update Extractor
5. Flash boot.img and recovery.img with fastboot.
6. Copy update app to dload folder on SD card, insert into the phone.
7. Restart phone with [VOL+] + [VOL-] + [Power] buttons to force update.
8. The system will be installed from SD card. I had no issues with the installation. First I did not format the phone (just wiped) and it did not work.
9. Restore data from backup.
The only strange thing is that the native app icons look different than my previous lollipop system. Don't know why. They are less colorful. I installed C00B220 for PLK-AL10.
Click to expand...
Click to collapse
Is this really work? i cant rollback to any version.
Yuaru said:
Is this really work? i cant rollback to any version.
Click to expand...
Click to collapse
Yes it does. (It did for me.) Technically this is not a rollback but installing a brand new system on an empty phone. That's why it is important to do a backup upfront.
tgergo said:
Yes it does. (It did for me.) Technically this is not a rollback but installing a brand new system on an empty phone. That's why it is important to do a backup upfront.
Click to expand...
Click to collapse
Thanks for the answer. Im gonna try this method. I can't reflash any region rom.
This is basically a copy of my Z380M TWRP thread adopted for the ZenPad 10. I decided to start a new one since the OP of justshaun's original recovery/rooting thread has gone stale, even as I had posted several new releases of TWRP over the months. Its instructions are also a little outdated. I've also compiled a version for the new Z301M(F) models and needed a place to post it. This is where I will be posting TWRP updates from now on.
In addition to this thread, referring to the Z380M TWRP thread and the original Z300M thread (links above) may be helpful. These models share the same hardware and software base, so most things that apply to one tablet also apply to the others.
DISCLAIMER
As usual, you do anything described in this post at your own risk. No one but you is responsible for any data loss, bricking or damage of your device.
REQUIREMENTS
Windows or Linux PC
SP Flash Tool version 5.1532 (only this version will bypass security checks)
MediaTek VCOM drivers (available through Windows Update)
ZenPad 10 scatter file for SPFT, attached (choose the one for your tablet)
Recovery image, attached (choose the one for your tablet)
ZenPad Z300M, Z301M or Z301MF tablet upgraded to Android N
This won't be a guide on how to use SP Flash Tool. There are plenty of good guides out there like this one on how to set up drivers, load scatter files, flash and make backups with SP Flash Tool. If you're not familiar with this software or how to flash MediaTek devices in general, please do your research before attempting this. I will just get straight to the specifics about the ZenPad 10.
FIRST TIME INSTALLATION
For a locked bootloader:
At this point you should have your tablet powered off, the drivers installed, all of your data backed up, and SP Flash Tool v5.1532's Download tab open and loaded with the tablet's scatter file. Open the download agent file DA_PL.bin, replacing the default MTK_AllInOne_DA.bin. (You can use the AllInOne DA if you want, but the procedure involves extra steps as described below.) Load the extracted TWRP recovery image for your device (twrp-3.2.1-0-z30*m.img) under the recovery partition line in the partition table. Click the Download button inside SPFT. Now just connect the USB cable to your tablet and your computer's USB port. It should start the download process automatically and disconnect when finished.
Alternative Method:
If you're using MTK_AllInOne_DA.bin, you have to hold the Volume Up key as you insert the cable, which puts the device into an emergency download mode. In addition, you will need to have the stock preloader*.bin file loaded inside SPFT for it to be able to communicate with your tablet. The preloader is available inside the official zip file download. Do not flash the preloader (untick the box) or any partitions other than recovery. You just need to have a valid bin file selected under the Preloader line.
For an unlocked bootloader:
If you have used the Asus unlock tool to unlock your device, you will still not be able to use fastboot flash to install a custom recovery. However, you can do a "hot boot" or a tethered boot of TWRP. This method doesn't require SP Flash Tool. Download the TWRP image, put your tablet in fastboot mode and connect to PC. Then run this command to boot TWRP dynamically:
fastboot boot twrp-3.2.1-0-z30*m.img
Once inside TWRP, flash twrp-3.2.1-0-z30*m.img to Recovery using Install -> Install Image. Then reboot to recovery. You may be able to use TWRP in the tethered boot mode, but that could result in glitches due to different parameters passed by the bootloader to the kernel. That's why flashing is recommended.
To update from your installed TWRP version to a new one, just transfer the image to your tablet, then boot to TWRP and install it by going to Install -> Install Image and flashing to Recovery.
START RECOVERY
With the tablet powered off, hold the Volume Up and Power keys together until you get to a menu where you can select "recovery". On the Z301M/Z301MF, that option is labeled Factory Reset. Use Vol. Up to scroll and Vol. Dn to select. If you have a locked bootloader, it will show a Yellow State message because the recovery is not signed by the OEM. Just press volume up to boot it. On the welcome screen of TWRP it will ask you about modifying the system partition, I suggest you go with Keep System Read-only. Doing otherwise will complicate your OTA updates.
WARNING: Never start the stock recovery from the bootloader menu on this device. It is programmed by the bootloader to instantly wipe your data without any warning. Also, be aware that Android installs the stock recovery at every normal boot cycle. So you either have to flash the TWRP every time you want to run it, or disable the automatic recovery installation in the stock firmware. Any kind of mod to the boot image will prevent the automatic recovery installation. If you're not sure which recovery you have installed, you can always do a 'adb reboot recovery' from Android without risk of data loss.
WARNING 2: Make sure you use the correct scatter file for your device (i.e. don't mix up the Z300 and Z301 files). For the initial flash, there is no check for scatter file correctness. If you use the wrong one, SP Flash Tool will alter and lock your GPT to that scatter file layout, possibly bricking your device. It will not be easy to restore it. Flashing with the correct scatter file later on will not work because Flash Tool will not allow you to use a different file than the one you used initially.
What works: Basically everything... access to major partitions, decrypted userdata partition, decrypted adoptable storage, external SD card, ADB, USB-OTG, touch interface, splash screen, installing stock Asus OTA/web FW updates
What doesn't work: (no known problems yet, but please report any)
Not guaranteed to work: factory reset
DOWNLOAD
SP Flash Tool v5.1532
Z300M Scatter file for all storage sizes (right click, Save link as...) -- do not use for other models
Z300M TWRP 3.2.1-0 image -- updated March 15, 2018
Z301M(F) series Scatter file for all storage sizes (right click, Save link as...) -- do not use for Z300M or other devices
Z301M TWRP 3.2.1-0 image -- updated March 13, 2018
Z301MF TWRP 3.2.3-0 image -- updated August 29, 2018
Development and experimental files
Source code
P.S. The thanks button doesn't bite.
Heya, thanks for the new thread..
Stupid question(coming from Samsung flashing)
Ive got Zenpad S3 10 P027, is this TRWP not ideal for this?
Currently, have some su (root) issues. Recovery shows Android icon chest with ! and says "No Command"
When running su in Terminal ADB via PC, says command not recognized.
Looks like I need to reflash recovery. When in TRWP (launched via fastboot boot twrp on PC) I flashed stock recovery but had system mounted read only. Could that be the problem?
Bro, I think you need to do some more homework on root, su, dm-verity, mods, etc. and read the instructions more carefully before applying these hacks. You are making a lot of simple mistakes and ending up shooting yourself in the foot for it. I don't think there's anything wrong with the Z500 TWRP. It can handle installing the stock firmware just fine. The problem is elsewhere. The unlock tool also works fine in TWRP as well in my testing.
The No Command screen is normal. That's been answered many times... you need to hold power+vol. up (or down) to get to the menu. There is no way the stock recovery image can be broken and still boot up.
The su thing, IDK what the problem is, but I'm sure if you install Magisk Manager and make your own patched image from your currently installed firmware, and fastboot-boot with it, you will have su functionality. Just like what it says in the unlock tool instructions.
Lastly and most important, never mount system in read-write mode, as I've repeated several times and exactly as it says in the directions:
7. At the TWRP welcome screen, do not select to modify the system partition and touch Keep System Read-only instead. Doing otherwise will render your tablet unbootable.
8. Mount system in TWRP (in read-only mode)
Click to expand...
Click to collapse
The only time you can mount it in read-write mode is when you are absolutely sure you have disabled dm-verity in your boot image.
I've successfully installed TWRP on Z301M using the instructions from the first post, but then I somehow managed to lose the system. Yes, I should have backed up like the OP suggests.
I thought I should be able to reinstall the original firmware downloaded from Asus (e.g. UL-ASUS_P028_1-WW-3.3.12.0-user.zip) but both the 'adb sideload' method and the TWRP failed to install that firmware zip. My device looks bricked. The only thing I can do is to boot into TWRP (I actually need to select Factory Reset on the bootloader screen to get into TWRP). The folder 'system' is empty.
Can anyone suggest what I am doing wrong when trying to restore the Asus firmware?
When I try to sideload the zip, setting TWRP in the sideload mode, the computer begins uploading but after a few seconds gives the message "Total xfer: 0.01x" and stops, while Android errors with "set boot part fail. can not open misc-sd".
When I install the firmware zip from TWRP it also starts installing fine but shortly gives the same error "set boot part fail. can not open misc-sd".
Thanks
@ahacker, first of all, thank you for the feedback on the Z301M platform. You are literally the first person to have said anything about that version of TWRP.
To see the files on system, you first have to mount the system partition. Did you do that? If not, I suggest mounting it read-only. If there was any corruption on it, then reinstalling the firmware should have fixed it. The "misc-sd" errors are normal. Pretty sure they happen on stock recovery too. The stock firmware does not have dm-verity enabled, so letting TWRP modify system to prevent overwriting recovery should not have caused any problems.
At which point did it stop booting? Also, did you use the scatter file from first post? And can you tell me if the touch screen works fine in TWRP on your tablet?
I'm not sure what the deal is with adb sideload. I don't think I've ever actually tried it....
diplomatic, thanks for replying!
diplomatic said:
[MENTION=4776997]
To see the files on system, you first have to mount the system partition. Did you do that?
Click to expand...
Click to collapse
I do mount the system partition. It appears empty. When I reboot into system TWRP says that the OS is not installed.
I don't remember the details of how I lost the system partition. First time I entered into TWRP it asked for a password, probably to mount some partition. I pressed cancel or something. Then I might have cleaned the caches. But I am sure I haven't wiped system. I might have pressed Factory Reset somewhere, because I don't have any data yet on the new tablet.
I would indeed try to mount the system read only. This is not the first Android system I rooted (maybe fifth), and I was always able to restore the system either from sideload or recovery. But here it seems Asus is making us jump extra hoops to do that.
diplomatic said:
[MENTION=4776997]
Reinstalling the firmware should have fixed it.
Click to expand...
Click to collapse
That seems to be my main problem now. I cannot reinstall the Asus firmware. It may look like I might be installing a wrong version, but I am positive that I have Z301M tablet. This is what I bought and what the boot-loader says. I download Z301M firmware from the Asus website (e.g.). So it must be a correct firmware.
diplomatic said:
[MENTION=4776997]
The "misc-sd" errors are normal. Pretty sure they happen on stock recovery too. The stock firmware does not have dm-verity enabled, so letting TWRP modify system to prevent overwriting recovery should not have caused any problems.
Click to expand...
Click to collapse
Thank you for the information.
diplomatic said:
[MENTION=4776997]
Also, did you use the scatter file from first post? Does the touch screen work fine in TWRP on that tablet?
Click to expand...
Click to collapse
Yes. I found that to be the only scatter file that worked. I tried scatter.txt from the firmware zip, but the Flash Tool refuses tio pick it up. TWRP seems to be working fine with touches working as expected.
diplomatic said:
[MENTION=4776997]
I'm not sure what the deal is with adb sideload. I don't think I've ever actually tried it....
Click to expand...
Click to collapse
This is the unbricking method described here. It probably does the same thing as the "Install Zip" from recovery, because the errors that both methods give are the same.
---------- Post added at 01:19 AM ---------- Previous post was at 12:57 AM ----------
Now system refuses to mount
ahacker said:
I don't remember the details of how I lost the system partition. First time I entered into TWRP it asked for a password, probably to mount some partition. I pressed cancel or something. Then I might have cleaned the caches. But I am sure I haven't wiped system. I might have pressed Factory Reset somewhere, because I don't have any data yet on the new tablet.
Click to expand...
Click to collapse
Er, the password should have been for decrypting your userdata. If you didn't have one set up, there might be something wrong there.... Or possibly just unformatted.
ahacker said:
That seems to be my main problem now. I cannot reinstall the Asus firmware. It may look like I might be installing a wrong version, but I am positive that I have Z301M tablet. This is what I bought and what the boot-loader says. I download Z301M firmware from the Asus website (e.g.). So it must be a correct firmware.
Click to expand...
Click to collapse
Yeah, that has to be the right one. The installation script has to match the model name reported by the recovery. Otherwise it would simply abort.
ahacker said:
Yes. I found that to be the only scatter file that worked. I tried scatter.txt from the firmware zip, but the Flash Tool refuses tio pick it up. TWRP seems to be working fine with touches working as expected.
Click to expand...
Click to collapse
Great! Guess my kernel patch was on the dot and the partition layout has not changed from the Z300.
ahacker said:
This is the unbricking method described here. It probably does the same thing as the "Install Zip" from recovery, because the errors that both methods give are the same.
Click to expand...
Click to collapse
When you installed the zip, did you unmount system completely? BTW, when you mentioned the errors, the installation does keep going for like 5 to 10 minutes afterwards, right?
If you still can't resurrect it, please post or send me the recovery & kernel log that has your installation attempt.
diplomatic said:
When you installed the zip, did you unmount system completely? BTW, when you mentioned the errors, the installation does keep going for like 5 to 10 minutes afterwards, right?
Click to expand...
Click to collapse
I've tried both ways, with and without system mounted, a few times. The installation would fail after something like 5 seconds.
diplomatic said:
If you still can't resurrect it, please post or send me the recovery & kernel log that has your installation attempt.
Click to expand...
Click to collapse
I think I am giving up on this cheap tablet. I cannot even format it in the Flash Tool: it says "To format code area is forbidden on this phone". Asus is forbidding too much for me to ever buy it again. Attached the logs.
Thanks, diplomatic
OK, found the problem. Check your PMs, ahacker.
diplomatic said:
OK, found the problem. Check your PMs, ahacker.
Click to expand...
Click to collapse
I have replied (twice), but the reply does not appear in my Sent Items. I hope it has reached you. If not, I'll paste the reply here, if you don't mind.
i not understand... i have Asus ZenPad 10 LTE Z301MFL.. a root method has been released ???
@diplomatic
Would this be compatible with Z0310M ? can't find anything for this damn model...
Hi, NeBouse,
Are you sure you have the correct information? It looks like just a misspelling of Z301M, aka P028....
I have z301m.
One thing that was a surprise for me is that the TWRP recovery flashed with the method described in the original post does not stick. You have to flash it each time you use it. If you are like me this information is important, because the original recovery plainly wipes your data without asking or warning.
After you have flashed TWRP on the device, to go to the recovery mode you have to chose "Factory Reset" in the bootloader. Then it will complain about wrong OS, which is the sign that flashing TWRP worked; choose 'yes'. The first thing you should do in TWRP is a ful nandroid backup. (Not listening the OP's advice about backing up when Installing TWRP with a wrong scatter file almost cost me the device. Thankfully diplomatic managed to remotely fix my problem, probably spending a lot of his personal time. The scatter file in the original post is a correct one now.)
Creating a nandroid backup in TWRP takes unusually long time, I even once decided that it hanged. Taking long time, like 10-30 minutes, for a full backup is normal.
Asus Z300M , Magisk 16.3 (beta) and FW 5.3.19 WW now works!
z301m, WW-3.3.12.0 firmware
For rooting I've installed in TWRP Magisk v15.3 (diplomatic warned against 16.x, someone else against 15.4) - link.
Installed in TWRP xPosed framework 88.2 - link, and xPosed Installer apk from within Android - link.
So far, so good.
What I've found is that TWRP seems to have problems with external sd cards (lots of fs corruption). I found it safer to unmount by hand by unticking the sd card checkbox in "Mount". Not very conclusive about this though.
Thanks, ahacker. Good feedback. Although to be fair, I didn't say to avoid Magisk 16.x. I said 16.0. I'm pretty sure whatever bug it had is already fixed in the latest version.
Now that you've installed root, TWRP will stick around on the emmc. The stock recovery only gets installed if you have the original unpatched boot image on it. I mean, this is not unique to these devices. That's been standard Android functionality since some 4.x or 5.x version. And this is essentially what's in the warning on the OP.
The backup I'm talking about in the installation method is done with the SP Flash Tool readback function. That will pull the partition tables and your device's "metadata" that's unique to your unit. I don't think nandroid covers that...
Oh, and what is this SD corruption you're talking about? What file system is it formatted in? Have you checked your card for errors in Windows?
Asus releases so many difference Z301M model, so I am curious if this also works on Z301MF model?
Notice Z300MF has the MTK8163BA (or MTK8163A?) CPU model while Z301M uses : 8163B
Anyone tested that already? Thanks.
my zenpad 10 has frp lock. it this a solution to remove the frp lock?
Pls help how i flash original software via fastboot ?????
Hi! I was trying to root Nokia 1
I flash TWRP through fastboot and it worked! But the problem was I was unable to see my files there.I think because of encryption..
So, I accidentally factory reset my phone through TWRP and then, I was unable to boot into system again..
I was stuck in TWRP
So, I go to fastboot and flash stock_recovery.IMG and after that when I reboot. I am seeing a black screen. I can feel vibration when press home key or home + volume up/down. but screen is black
Please help...
abdul_manan said:
Hi! I was trying to root Nokia 1
I flash TWRP through fastboot and it worked! But the problem was I was unable to see my files there.I think because of encryption..
So, I accidentally factory reset my phone through TWRP and then, I was unable to boot into system again..
I was stuck in TWRP
So, I go to fastboot and flash stock_recovery.IMG and after that when I reboot. I am seeing a black screen. I can feel vibration when press home key or home + volume up/down. but screen is black
Please help...
Click to expand...
Click to collapse
Use micro SD card for twrp. You can't remove encryption just by factory reset. I know how to remove encryption on Nougat but that method doesn't work on Oreo. When you flashed TWRP flash SuperSU (not Magisk) then boot to system, after that boot to twrp recovery again and wipe factory reset and wipe internal storage. You have removed encryption. SuperSU needs to be updated to patch plat and non play file contexts to remove encryption on Oreo. Or someone can make flashable zip to remove encryption.
First find nb0 file for Nokia 1 and try to flash rom with OST.
SkaboXD said:
Use micro SD card for twrp. You can't remove encryption just by factory reset. I know how to remove encryption on Nougat but that method doesn't work on Oreo. When you flashed TWRP flash SuperSU (not Magisk) then boot to system, after that boot to twrp recovery again and wipe factory reset and wipe internal storage. You have removed encryption. SuperSU needs to be updated to patch plat and non play file contexts to remove encryption on Oreo. Or someone can make flashable zip to remove encryption.
First find nb0 file for Nokia 1 and try to flash rom with OST.
Click to expand...
Click to collapse
Thanks for the reply!
Can you please tell me where can I find the nb0 file of Nokia 1 with Android 8.1 Oreo Go edition TA-1047?
abdul_manan said:
Thanks for the reply!
Can you please tell me where can I find the nb0 file of Nokia 1 with Android 8.1 Oreo Go edition TA-1047?
Click to expand...
Click to collapse
currently it's not available, you need to wait someone to upload it.
Nokia1 uses MTK CPU right? If you can get the ota zip of the current update on your phone, you can extract the boot.img file then boot into download mode and type fast boot flash boot <boot.img file>
redweaver said:
Nokia1 uses MTK CPU right? If you can get the ota zip of the current update on your phone, you can extract the boot.img file then boot into download mode and type fast boot flash boot <boot.img file>
Click to expand...
Click to collapse
Can you please explain a little bit more!
How to get ota zip file? (My phone is not working as mentioned above)
Where can I get boot.img?
How to extract and where boot.img?
How to boot into download mode?
abdul_manan said:
Hi! I was trying to root Nokia 1
I flash TWRP through fastboot and it worked! But the problem was I was unable to see my files there.I think because of encryption..
So, I accidentally factory reset my phone through TWRP and then, I was unable to boot into system again..
I was stuck in TWRP
So, I go to fastboot and flash stock_recovery.IMG and after that when I reboot. I am seeing a black screen. I can feel vibration when press home key or home + volume up/down. but screen is black
Please help...
Click to expand...
Click to collapse
I'm having a kind of similar issue. I flashed twrp and now its stuck in a twrp loop. It boots only in twrp and not system. What should I do?
Ludba Amb said:
Can you please explain a little bit more!
How to get ota zip file? (My phone is not working as mentioned above)
Where can I get boot.img?
How to extract and where boot.img?
How to boot into download mode?
Click to expand...
Click to collapse
http://www.mediafire.com/file/0xgn9o0b711wcw0/Nokia_1_TA-1047_MT6735_V8.1.0_180401.zip
Stock Rom for 1047
Download it.
Extract boot.img from that
boot into download mode/recovery
adb reboot recovery
answers to all your questions.... not the answer to fix your problem I think... But have a go.
And last but not least... Please use the search option first or google instead of asking all questions at once.
Or try to get familiar with rooting first...…
good luck buddy.
hello everyone i have nokia 1 oreo go edition i don't have any idea how to root
please help me by sending links for :
1 ) nokia 1 (ta-1047 ) TWRP
2 ) nokia 1 custom rom
3 ) nokia 1 current rom (for security)
(remenber thats only model ta-1047)
seriously i want to root it because there are many issues like multitouch screen problem or missing some system apps and also device getting hot because the memory (ram) is lagging (1gb ram is not enough to run android oreo correctly 2018 )
{PLEASE HELP}
help me please !
can you send me a twrp for nokia 1 ta-1047
i need to root my device to dowoad custom rom
MyTH30 said:
I'm having a kind of similar issue. I flashed twrp and now its stuck in a twrp loop. It boots only in twrp and not system. What should I do?
Click to expand...
Click to collapse
Same here. Seems that the decryption does not work. Better make sure your phone is not encrypted before messing with twrp (3.2.3).
Be careful
Some Nokia 1 are a TA 1060 variant number and if you flash the wrong file you are going to have further problems.
The process to root and get TWRP on the nokias Is complicated enough without everyone suggesting wrong model variants / numbers.
I guarantee someone will download the wrong file for the wrong model and come here crying.
is this the real firmware?
inkepinkje said:
http://www.mediafire.com/file/0xgn9o0b711wcw0/Nokia_1_TA-1047_MT6735_V8.1.0_180401.zip
Stock Rom for 1047
Download it.
Extract boot.img from that
boot into download mode/recovery
adb reboot recovery
answers to all your questions.... not the answer to fix your problem I think... But have a go.
And last but not least... Please use the search option first or google instead of asking all questions at once.
Or try to get familiar with rooting first...…
good luck buddy.
Click to expand...
Click to collapse
hi, i needed to know if this is the real one, they show it's mt6735 instead mt6737m, I've already downloaded a file with the similar name nd it has scatter file of mt6735, that's while in the sp flash tool,i don't see all of the partitions being detected to flash
Hey i am facing the same issue but i didn't flash any other recovery mode my phone Nokia 1 TA-1056 am getting black screen and only feel the vibration when i press power key and when i put my phone on charging then its shows the display and boot into recovery mode directly can anyone help me how i can overcome this issue