Related
Are there other ways to flash a recovery with a locked bootloader?
My Problems:
I can't flash my stock recovery through fastboot with a locked bootloader.
I can't boot into my recovery because my current recovery is TWRP 2.5.0.1 and I have a locked bootloader.
I can't unlock my bootloader because I have used an IMEI Hack Tool and set my IMEI to 0 (I guess).
I can't boot into my ROM because I used an IMEI Hack Tool.
I can't Force Upgrade too (Vol Up + Down + Power). It only shows a pink/purple screen.
Solutions:
I can only flash a recovery with an unlocked bootloader.
I can only boot into a recovery with an unlocked bootloader (except for stock).
I can only unlock bootloader if my IMEI has restored.
I can only restore my IMEI if I can boot into my ROM.
I can only boot into my ROM if I have a stock recovery.
I can only Force Upgrade if I have restored my IMEI.
If I could only restore my IMEI through fastboot, that would be great!
So, please help!
You cant restore stock recovery ?
You cant enter to trwp ?
You cant restore IMEI cuz rom bootloop ?
You cant force flash stock firmware cuz fastboot is pink ?
I also "zero" my imei many times to flash stock firmware, but i allways can enter trwp and restore buckup or flash rom in zip
OmenHTX said:
You cant restore stock recovery ?
You cant enter to trwp ?
You cant restore IMEI cuz rom bootloop ?
You cant force flash stock firmware cuz fastboot is pink ?
I also "zero" my imei many times to flash stock firmware, but i allways can enter trwp and restore buckup or flash rom in zip
Click to expand...
Click to collapse
I can force upgrade now since i formatted my sd card. But the force upgrade fails at step 2/2.
.vonpatrick. said:
I can force upgrade now since i formatted my sd card. But the force upgrade fails at step 2/2.
Click to expand...
Click to collapse
If upgrade fail as step 2/2 your IMEI its not "zero" cuz IMEI block upgrading firmware from branded to nonbranded
OmenHTX said:
If upgrade fail as step 2/2 your IMEI its not "zero" cuz IMEI block upgrading firmware from branded to nonbranded
Click to expand...
Click to collapse
If my imei is not zero, then why can't i boot my phone?
And why can't i unlock my bootloader with my unlock code?
.vonpatrick. said:
If my imei is not zero, then why can't i boot my phone?
And why can't i unlock my bootloader with my unlock code?
Click to expand...
Click to collapse
OK, lest start from beggining
1.You must unlock bootloader by code ( first run check Lock / Unlock status ) (fastboot mod)
2. Flash TRWP (fastboot mod)
3. Flash SuperSU or Superuser zip (trwp)
4. Backup IMEI on running rom
5. Hack IMEI on running rom
6. Update phone by forceupdate flash update.app (rom in root of sd card > folder dload > update.app)
7. Run stock rom , lest install, shut down phone
8. Run TRWP to install SuperSU/Superuser zip
8. Restore IMEI (on working rom)
9. Go to TRWP and Wipe dalvik cache
10. Now you have working newest stock rom with root
So :
1. You cant have trwp in lockedbootloader
2. If update fail on 2/2 IMEI is not "zero"
3. Pink LCD on "update mod" = no rom in sd card
Next :
Hold Vol Down + Vol Up + Power to forceupdate firmware mod
Hold Vol Up + Power to run TRWP or stock recovery ( hold about 5s)
Hold Vol Down + Power for fastboot mod (5s-10s)
If you now have locked bootloader , with stock recovery, and force update fail, you cant unlock bootloader and flash trwp > Last hope is in "oryginal" rom, your IMEI will not block it.
OmenHTX said:
OK, lest start from beggining
1.You must unlock bootloader by code ( first run check Lock / Unlock status ) (fastboot mod)
2. Flash TRWP (fastboot mod)
3. Flash SuperSU or Superuser zip (trwp)
4. Backup IMEI on running rom
5. Hack IMEI on running rom
6. Update phone by forceupdate flash update.app (rom in root of sd card > folder dload > update.app)
7. Run stock rom , lest install, shut down phone
8. Run TRWP to install SuperSU/Superuser zip
8. Restore IMEI (on working rom)
9. Go to TRWP and Wipe dalvik cache
10. Now you have working newest stock rom with root
So :
1. You cant have trwp in lockedbootloader
2. If update fail on 2/2 IMEI is not "zero"
3. Pink LCD on "update mod" = no rom in sd card
Next :
Hold Vol Down + Vol Up + Power to forceupdate firmware mod
Hold Vol Up + Power to run TRWP or stock recovery ( hold about 5s)
Hold Vol Down + Power for fastboot mod (5s-10s)
If you now have locked bootloader , with stock recovery, and force update fail, you cant unlock bootloader and flash trwp > Last hope is in "oryginal" rom, your IMEI will not block it.
Click to expand...
Click to collapse
Wait, let me put this in summary:
1.
- I have a locked bootloader.
- I can't unlock the bootloader because it says "recovery image verify failed".
- It can only mean one thing: my IMEI must have changed.
2.
- I have a TWRP recovery.
- At first, my original recovery was the stock when I have a locked bootloader.
- Then I flashed the TWRP recovery even if I have a locked bootloader and didn't warned me. (Shoudn't it be accepted to be flashed since I have a locked bootloader).
- In my experience, if I have a stock recovery when I'll hack my IMEI, it will format my cache and data and let me boot into my phone.
- If I have a TWRP recovery when I'll hack my IMEI, it will only redirect me to the TWRP menu.
3.
- I can access Force Upgrade.
- But it doesn't show any text. (For example: it doesn't show if it is unpacking or installing, only a bar.)
- When I access Force Upgrade, the loading stops at 1/4 of the bar. (So I'm not really sure if it failed at step 2/2.)
So my questions are:
1. Why can't I unlock my bootloader with my original IMEI's unlock code if my IMEI is not "zero"?
2. Why is it when I Force Upgrade, it doesn't show any text?
3. Why did fastboot accepted the TWRP recovery being flashed when my bootloader was locked?
And, what do you mean by "original"? Do you mean the B182 firmware upgrade, not the B175?
After hacking IMEI you cant have stock recovery, cuz you need root for shell script. So its not making "auto wipe" to change OEM info.
TRWP should not be installed on lockbootloader, but i dont make it ...
So , do you have working trwp or not ?
Oryginal firmware ... version when you get with phone, like my Y300-0100 branded T-Mobile PL B167
OmenHTX said:
After hacking IMEI you cant have stock recovery, cuz you need root for shell script. So its not making "auto wipe" to change OEM info.
TRWP should not be installed on lockbootloader, but i dont make it ...
So , do you have working trwp or not ?
Oryginal firmware ... version when you get with phone, like my Y300-0100 branded T-Mobile PL B167
Click to expand...
Click to collapse
I am sure i have twrp.
If i have a stock recovery, i would be able to boot into recovery.
Based in my experience:
1. To hack the imei, you must first root your phone.
2.a. Next, the phone will reboot, but it won't boot into system.
2.b. Fastboot, force upgrade, and recovery is still accessible.
3.a. If you have a twrp recovery when you hacked the imei and rebooted, it will redirect you to the twrp menu.
3.b. If you tried to restore from twrp recovery, it still won't reboot into system.
3.c. If you have a stock recovery, it will directly boot into stock recovery and format your cache and data and reboot to system (still leaves your imei to zero)
4. If you go to force upgrade, you can flash any official roms (leaves your imei to zero)
5. After you have flashed a rom or was redirected to stock recovery, your phone will reboot.
6.a. Then root your phone and restore imei then your phone will reboot.
6.b. If you have a stock recovery, it will wipe your cache and data.
6.c. If you have a twrp recovery, it will redirect you to the twrp menu (you can manually reboot into system)
Am i right?
And where can i get the original rom for my b182? There's no local huawei store here.
.vonpatrick. said:
I am sure i have twrp.
If i have a stock recovery, i would be able to boot into recovery.
Click to expand...
Click to collapse
So why you dont run TRWP and flash any rom in zip ?
OmenHTX said:
So why you dont run TRWP and flash any rom in zip ?
Click to expand...
Click to collapse
Twrp is not accessible if you have a locked bootloader.
bricked
I have a big problem. My Ascend y300 started to work strange yesterday, my PC didnt see the internal sd nor the external SD correctly. Today I restarted it and now I get blue screen when I start it. I had TWRP installed, but when I try to access it, it gives blue screen aswell. Any solutions?
gery0518 said:
I have a big problem. My Ascend y300 started to work strange yesterday, my PC didnt see the internal sd nor the external SD correctly. Today I restarted it and now I get blue screen when I start it. I had TWRP installed, but when I try to access it, it gives blue screen aswell. Any solutions?
Click to expand...
Click to collapse
Try this through fastboot:
fastboot erase recovery
fastboot flash recovery <path to recovery.img>
.vonpatrick. said:
Try this through fastboot:
fastboot erase recovery
fastboot flash recovery <path to recovery.img>
Click to expand...
Click to collapse
My problem is a little bit more complex unfortunately. I tried what you said. When I push the buttons to enter fastboot, my phone dont freez at splashscreen and I get bluescreen. When I connect it to my PC my PC recognizes it though, BUT ADB cant see it. I reinstalled the drivers any times, without success.
gery0518 said:
My problem is a little bit more complex unfortunately. I tried what you said. When I push the buttons to enter fastboot, my phone dont freez at splashscreen and I get bluescreen. When I connect it to my PC my PC recognizes it though, BUT ADB cant see it. I reinstalled the drivers any times, without success.
Click to expand...
Click to collapse
What did you do anyway why it got the blue screen?
.vonpatrick. said:
What did you do anyway why it got the blue screen?
Click to expand...
Click to collapse
That is the most strange part of the story. I totally did nothing. I opened bootloader, installed twrp, rooted it, installed init.d support, installed a ramscript. The phone worked totally fine until yesterday. I did a restart yesterday and bumm, bluescreen. And I did nothing before this happened. Srsly, no problems detected, it came from nothing...
gery0518 said:
That is the most strange part of the story. I totally did nothing. I opened bootloader, installed twrp, rooted it, installed init.d support, installed a ramscript. The phone worked totally fine until yesterday. I did a restart yesterday and bumm, bluescreen. And I did nothing before this happened. Srsly, no problems detected, it came from nothing...
Click to expand...
Click to collapse
Can't you really boot into fastboot (Power + up)?
Hold it for like 10 seconds.
If it still shows blue screen, try connecting it to pc, maybe it'll read it.
Then erase recovery and flash twrp.
Wipe everything and restore a backup you made.
.vonpatrick. said:
Can't you really boot into fastboot (Power + up)?
Hold it for like 10 seconds.
If it still shows blue screen, try connecting it to pc, maybe it'll read it.
Then erase recovery and flash twrp.
Wipe everything and restore a backup you made.
Click to expand...
Click to collapse
Well, my problem is, that despite of the blue screen, fastboot seems to work. My pc sees my device, BUT ADB refuses to see it, and I dont know why. I will try it from win xp under virtualbox now.
hi Gery
How do you manage to get the phone into fastboot mode?
my y300 also enters blue screen everytime now. I try to press voldown + power for like 10 seconds, yet the fastboot command is not working.
gery0518 said:
Well, my problem is, that despite of the blue screen, fastboot seems to work. My pc sees my device, BUT ADB refuses to see it, and I dont know why. I will try it from win xp under virtualbox now.
Click to expand...
Click to collapse
Well, that's perfect! If the PC can read the device from fastboot, you can erase the recovery and flash the twrp and restore from backup. But if it still goes blue, flash the system, data, cache, boot, recovery from your twrp backup.
I need help, My phone was unlocked officially, and I have ZCX TWRP build 28081016 before. Then I flash Nougat ROM (Pure Nexus) from MIUI 8 8.2.3.0 without Wipe Internal Storage. Then it works normally. But since I go back to TWRP, I got Decrypt Data with password there. So I cancel it and then I got 0 Internal Storage. And it back while i text some **** in the decrypt password.
While reboot to system, It also asking password too.
Then I reflashing ROM with Clean Install method (wipe anything) but its still asking goddamn passwords.
Then I go Reboot Recovery again and text any **** password but it works! I got my Internal Storage back.
Then I try to flash zcx recovery build 30122016 (latest version) from recovery. Now I got my recoveries gone. There's only phone with usb cable images. Anything goes wrong (corrupted boot.img or something) here? Is it save if I reflash from PC? How to don't get decrypt sdcard?
I got other problem too. I have changed my splash logo (boot logo) using Google Pixels boot logo here. But I have never come back to Mi splash logo while clean installing MIUI ROM from recovery. Where is my problem here?
And this is my big problem (maybe) (cause I still don't get problems here). Anyone of you facing your Fastboot Logo with tiny Linux Penguin images? I can't go "adb reboot fastboot" here. And I can go to fastboot mode with volume- + power button only. It's not working too with reboot bootloader in TWRP. I guess my fastboot isn't working with Miflash or some ****. But works with adb. How can I get Mi Bunny Fastboot again?
Please help me. and tell me what should I do. Thankyou.
ojedee said:
I need help, My phone was unlocked officially, and I have ZCX TWRP build 28081016 before. Then I flash Nougat ROM (Pure Nexus) from MIUI 8 8.2.3.0 without Wipe Internal Storage. Then it works normally. But since I go back to TWRP, I got Decrypt Data with password there. So I cancel it and then I got 0 Internal Storage. And it back while i text some **** in the decrypt password.
While reboot to system, It also asking password too.
Then I reflashing ROM with Clean Install method (wipe anything) but its still asking goddamn passwords.
Then I go Reboot Recovery again and text any **** password but it works! I got my Internal Storage back.
Then I try to flash zcx recovery build 30122016 (latest version) from recovery. Now I got my recoveries gone. There's only phone with usb cable images. Anything goes wrong (corrupted boot.img or something) here? Is it save if I reflash from PC? How to don't get decrypt sdcard?
I got other problem too. I have changed my splash logo (boot logo) using Google Pixels boot logo here. But I have never come back to Mi splash logo while clean installing MIUI ROM from recovery. Where is my problem here?
And this is my big problem (maybe) (cause I still don't get problems here). Anyone of you facing your Fastboot Logo with tiny Linux Penguin images? I can't go "adb reboot fastboot" here. And I can go to fastboot mode with volume- + power button only. It's not working too with reboot bootloader in TWRP. I guess my fastboot isn't working with Miflash or some ****. But works with adb. How can I get Mi Bunny Fastboot again?
Please help me. and tell me what should I do. Thankyou.
Click to expand...
Click to collapse
You got your device encryption so remove it
Boot to fast boot volume - plus power button combo then connect to PC
Then use fast boot modified in order to boot into edl
Then flash latest miui fast boot ROM through miflash
Then reboot
Then unlock bootloader flash zcx twrp the hen format data from twrp under wipe option
[email protected] said:
You got your device encryption so remove it
Boot to fast boot volume - plus power button combo then connect to PC
Then use fast boot modified in order to boot into edl
Then flash latest miui fast boot ROM through miflash
Then reboot
Then unlock bootloader flash zcx twrp the hen format data from twrp under wipe option
Click to expand...
Click to collapse
But i have never ever encrypt anything on my phone. Now my device can't do adb reboot fastboot. But if i reboot to recovery first. It works with power and volume down
I was into the process of rooting my XT1506. Unlocked the bootloader and installed twrp successfully and then in an attempt to installing custom rom via Fastboot, i run the command
fastboot -w
and then when i tried to run "fastboot update rom.zip", it didn't succeed. After that, whatever i do, the phone just boots into recovery and never into the system. Badly need your help, Guys....!!! I shall be really thankful.....
I think i made the thread in wrong section and now i cant find the option to move/delete it. I apologize Mods for this mistake and request them to move it.
aanishjangra said:
I was into the process of rooting my XT1506. Unlocked the bootloader and installed twrp successfully and then in an attempt to installing custom rom via Fastboot, i run the command
fastboot -w
and then when i tried to run "fastboot update rom.zip", it didn't succeed. After that, whatever i do, the phone just boots into recovery and never into the system. Badly need your help, Guys....!!! I shall be really thankful.....
Click to expand...
Click to collapse
If you still have twrp installed, you can wipe everything and flash the custom ROM from the recovery itself.
Tried that too...still it boots into recovery...One more thing i have noticed that in fastboot mode, clicking on "Factory" boots the phone normally.
Is there any problem related with recovery. I have presently Flyrom 5.1.2 installed and recovery is 3.0.1 (also tried twrp-otus-2.7.x), if that helps..
Download any Custom ROM (Lineage OS recommended)
Put that in your SDCard or Internal Storage (USB MTP works in recovery mode)
Go To Wipe Section and check All (Excluding Internal Or MicroSD)
Swipe to format
Then Press the HOME Button
Click on Install
Go to the path where ROM is (Root of the storage is best)
Flash the ROM
Wipe cache/Dalvik Cache (Must Do This)
First Boot may take 15-20 min...
Enjoy :fingers-crossed:
Hit Thanks If I Helped you
Problem solved. I think it was a problem with the recovery. I achieved the solution by flashing stock recovery. Now the phone is booting normal.
I am curious if anybody can suggest me a compatible recovery for this phone. By the way, thanx to all who helped me....You are awesome
Go for this : Recovery
And thread here : https://forum.xda-developers.com/moto-e-2015/orig-development/twrp-recovery-moto-e-3g-2015-t3084849
shaktiman01 said:
Go for this : Recovery
And thread here : https://forum.xda-developers.com/moto-e-2015/orig-development/twrp-recovery-moto-e-3g-2015-t3084849
Click to expand...
Click to collapse
That is the same recovery which caused the problems. Anyways, i'll try to put that in again and see if there'll be any difference. Btw, thanx mate..
@ aanishjangra try squid2's port of the recovery and see if it helps, although ensure you flash the recovery and immediately reboot to recovery (Not system) and the ROM gets patched.
aanishjangra said:
I was into the process of rooting my XT1506. Unlocked the bootloader and installed twrp successfully and then in an attempt to installing custom rom via Fastboot, i run the command
fastboot -w
and then when i tried to run "fastboot update rom.zip", it didn't succeed. After that, whatever i do, the phone just boots into recovery and never into the system. Badly need your help, Guys....!!! I shall be really thankful.....
Click to expand...
Click to collapse
https://chat.whatsapp.com/AimXKJXu6uUJp6qOvBeOan
Join whtsapp group if u need any help!!
Hi everybody i need your help,
I got an honor 9 STF-L09. I got bricked and I want to install the stock firmware because my phone doesnt on again. I have Twrp installed and unlocked bootloader but when i try to boot into system it says "Func NO: 10 (boot image)".
I tried to flash firmware from thi guide https://forum.xda-developers.com/honor-9/development/firmware-huawei-honor-9-stf-l09-stock-t3696892 but nothing to do.
I tried to flash using twrp but the ionstallation fail everytime.
Is there someone that can help me with a stock firmware or even other firmwares that makes my H9 on againg.
Please help me I'am DESPERATE
Did you take a look here ?
http://droidvendor.com/download-8-0-0-360-c432-official-oreo-for-honor-9-stf-l09/
sorry, I'm not expert on this topic, it's the only help i can give you
What rom did you have before? EMUI 8 or 5.1?
JBolho said:
What rom did you have before? EMUI 8 or 5.1?
Click to expand...
Click to collapse
I had emui 8
leocap33 said:
I had emui 8
Click to expand...
Click to collapse
I will provide you with the files that (hopefully) will bring your device back to life. Just need to upload the first, i'll update this post with the link and instructions, hang on a second.
JBolho said:
I will provide you with the files that (hopefully) will bring your device back to life. Just need to upload the first, i'll update this post with the link and instructions, hang on a second.
Click to expand...
Click to collapse
thank you man
leocap33 said:
thank you man
Click to expand...
Click to collapse
In the link you will find Stock EMUI 8 Ramdisk, Recovery and System, as well as TWRP and a Kernel that fixes the possibility of losing the capacitive buttons. Download them into a folder on the root of your PC (for example C:\Temp)
https://www.dropbox.com/sh/88l72rypm6u1u94/AADtPyvsIFhyBl1mcJ5raTBZa?dl=0
I don't know what caused your boot to disappear, mine disappeared when i tried to unroot it from within SuperSU app (Big Mistake), but let's not be drastic just yet. You need Fastboot and ADB on your PC, turn off your phone, hold Volume - and connect the USB cable from the PC to the device. You should enter Fastboot mode. I hope your device is FRP unlocked as well.
Open a command line and input "fastboot devices" to make sure your device is connected
First let's try restoring Ramdisk, TWRP and Kernel:
Run "fastboot flash ramdisk STF-L09_ramdisk.img", then "fastboot flash recovery_ramdisk stf_twrp_oreo.img" and finally "fastboot flash kernel B360_fix_kernel.img"
After that just run "fastboot reboot" and see if it boots or not... This should take care of your problem, if not, let's go drastic:
Turn off the device and plug it in fastboot mode again onto your PC.
On the command line run "fastboot flash recovery_ramdisk RECOVERY_RAMDISK.img" (this will flash stock recovery), and "fastboot flash system SYSTEM.img" (this will flash your system partition, in small bathes at a time, fresh.)
After that, just "fastboot reboot" and it should boot to your system (and without a factory reset!) If it bootloops for some reason, turn off the device, boot into stock recovery and wipe cache (or do a full factory reset, but that should not be necessary i think...)
Hope all this helps!
JBolho said:
In the link you will find Stock EMUI 8 Ramdisk, Recovery and System, as well as TWRP and a Kernel that fixes the possibility of losing the capacitive buttons. Download them into a folder on the root of your PC (for example C:\Temp)
https://www.dropbox.com/sh/88l72rypm6u1u94/AADtPyvsIFhyBl1mcJ5raTBZa?dl=0
I don't know what caused your boot to disappear, mine disappeared when i tried to unroot it from within SuperSU app (Big Mistake), but let's not be drastic just yet. You need Fastboot and ADB on your PC, turn off your phone, hold Volume - and connect the USB cable from the PC to the device. You should enter Fastboot mode. I hope your device is FRP unlocked as well.
Open a command line and input "fastboot devices" to make sure your device is connected
First let's try restoring Ramdisk, TWRP and Kernel:
Run "fastboot flash ramdisk STF-L09_ramdisk.img", then "fastboot flash recovery_ramdisk stf_twrp_oreo.img" and finally "fastboot flash kernel B360_fix_kernel.img"
After that just run "fastboot reboot" and see if it boots or not... This should take care of your problem, if not, let's go drastic:
Turn off the device and plug it in fastboot mode again onto your PC.
On the command line run "fastboot flash recovery_ramdisk RECOVERY_RAMDISK.img" (this will flash stock recovery), and "fastboot flash system SYSTEM.img" (this will flash your system partition, in small bathes at a time, fresh.)
After that, just "fastboot reboot" and it should boot to your system (and without a factory reset!) If it bootloops for some reason, turn off the device, boot into stock recovery and wipe cache (or do a full factory reset, but that should not be necessary i think...)
Hope all this helps!
Click to expand...
Click to collapse
thank you a lot, u give me hope. When I return home I'll try everything
JBolho said:
In the link you will find Stock EMUI 8 Ramdisk, Recovery and System, as well as TWRP and a Kernel that fixes the possibility of losing the capacitive buttons. Download them into a folder on the root of your PC (for example C:\Temp)
https://www.dropbox.com/sh/88l72rypm6u1u94/AADtPyvsIFhyBl1mcJ5raTBZa?dl=0
I don't know what caused your boot to disappear, mine disappeared when i tried to unroot it from within SuperSU app (Big Mistake), but let's not be drastic just yet. You need Fastboot and ADB on your PC, turn off your phone, hold Volume - and connect the USB cable from the PC to the device. You should enter Fastboot mode. I hope your device is FRP unlocked as well.
Open a command line and input "fastboot devices" to make sure your device is connected
First let's try restoring Ramdisk, TWRP and Kernel:
Run "fastboot flash ramdisk STF-L09_ramdisk.img", then "fastboot flash recovery_ramdisk stf_twrp_oreo.img" and finally "fastboot flash kernel B360_fix_kernel.img"
After that just run "fastboot reboot" and see if it boots or not... This should take care of your problem, if not, let's go drastic:
Turn off the device and plug it in fastboot mode again onto your PC.
On the command line run "fastboot flash recovery_ramdisk RECOVERY_RAMDISK.img" (this will flash stock recovery), and "fastboot flash system SYSTEM.img" (this will flash your system partition, in small bathes at a time, fresh.)
After that, just "fastboot reboot" and it should boot to your system (and without a factory reset!) If it bootloops for some reason, turn off the device, boot into stock recovery and wipe cache (or do a full factory reset, but that should not be necessary i think...)
Hope all this helps!
Click to expand...
Click to collapse
Hi sir I tried, everything flashes ok but when I reboot it continue bootloops until it enter into erecovery. I tried to wipe data but when I press the button to wipe cache after it displays a red '!' into the circle and the same for the wiping data.
sorry for my English, how can I solve ..? FRP was written "FRP unlock"
leocap33 said:
Hi sir I tried, everything flashes ok but when I reboot it continue bootloops until it enter into erecovery. I tried to wipe data but when I press the button to wipe cache after it displays a red '!' into the circle and the same for the wiping data.
sorry for my English, how can I solve ..? FRP was written "FRP unlock"
Click to expand...
Click to collapse
Everything flashes ok, no errors? What did you flash? Everything?
eRecovery is to rescue the device, that won't work with Oreo (at least not for me). The stock recovery you enter it by keeping the Vol + pressed and power up the device (just as TWRP), you can enter it? And it gives error when wiping the cache?
JBolho said:
Everything flashes ok, no errors? What did you flash? Everything?
eRecovery is to rescue the device, that won't work with Oreo (at least not for me). The stock recovery you enter it by keeping the Vol + pressed and power up the device (just as TWRP), you can enter it? And it gives error when wiping the cache?
Click to expand...
Click to collapse
yes it gives me an error while I wipe cache or factory data. I enter normally into recovery with vol+.
leocap33 said:
yes it gives me an error while I wipe cache or factory data. I enter normally into recovery with vol+.
Click to expand...
Click to collapse
What ROM exactly were you using? OldDroid's B360? Or some other?
I were using the stock emui8 I don't know the build number because I can't get it. My region is italy
leocap33 said:
I were using the stock emui8 I don't know the build number because I can't get it. My region is italy
Click to expand...
Click to collapse
The only explanation i see is that the EMUI8 you were using has something different from the one in OldDroid's thread... On mine i did exactly what i told you, those files are the ones i used on mine as well.
Right now you have everything stock right? Can you try to flash one of the Treble Roms? Either AOSP or RR-O?
You just have to download them (they're a system.img file) and run the "fastboot flash system system.img" command, go to recovery and factory reset. Your device should boot.
If everything fails, the only hope i see if to go to OldDroid's thread - https://forum.xda-developers.com/honor-9/how-to/stf-l09c432-how-to-install-oreo-h9-t3707729 and download the files, and follow the instructions on the OP to rollback to Nougat.
sonneper said:
Did you take a look here ?
http://droidvendor.com/download-8-0-0-360-c432-official-oreo-for-honor-9-stf-l09/
sorry, I'm not expert on this topic, it's the only help i can give you
Click to expand...
Click to collapse
I think the link you probided is a fake bull$hiting guide :
1) it states european C432 but provided two of the three files of a russian C10 firmware.
2) almost sure. the file provided won't flash the dload way as stated in guide.
leocap33 said:
Hi everybody I got an honor 9 STF-L09, my region is italy. I got bricked and I want to install the stock firmware because my phone doesnt on again. I have Twrp installed and unlocked bootloader but when i try to boot into system it says "Func NO: 10 (boot image)".
I tried to flash firmware from thi guide https://forum.xda-developers.com/honor-9/development/firmware-huawei-honor-9-stf-l09-stock-t3696892 but nothing to do.
I tried to flash using twrp but the ionstallation fail everytime.
Is there someone that can help me with a stock firmware or even other firmwares that makes my H9 on againg.
Please help me I'am DESPERATE
Click to expand...
Click to collapse
OK, so you were on oreo, and now the nougat's service repair dload firmware are not working.
I'll start by asking:
-how do you get bricked, what did you do just before ?
Try this tool for honor 9:
https://forum.xda-developers.com/newreply.php?do=newreply&p=75084955
(xda link to russian tool)
https://forum.xda-developers.com/newreply.php?do=newreply&p=75661658
(xda link to english translated scripts)
http://4pda.ru/forum/index.php?showtopic=833645&st=2400#entry69940847
(pda link to russian tool)
Same here, I just have access to eRecovery and fastboot mode
I was on the last version (oreo) and I wanted root my phone so I have unlock bootloader and install twrp but after twrp install in the wipe my internal stockage was empty and when I wanted install supersu I have some error like failed to mount: data, failed to mount: cache, ect..
but I still had access to my phone
Except that I had to go through the eRecovery every time so I tried to look at the side of my errors mount and I tried unbrick with the software Huawei Multi Tool and images of a rom stock publish on the forum except that I had even more access to my phone but I no longer have the errors mount.. With Huawei Multi Tool I have try the recovery option but nothing, now I don't know what make
Hi everyone I tried all the tools given into this thread but no success, it seems like a big lost challenge
Tell us more..
so you were on oreo or nougat before brick ?
and now the nougat's service repair dload firmware are not working ?
how do you get bricked, what did you do just before ?
Yeah never see a sht like that, I guess we have to send our phones to a huawei repair center..
Ok you were on oreo emui8.
EDIT:
In my way of trying to apply to warranty and flashing the stock package into the phone and Windows being Windows, I had problems using the batch script, it stopped for long time and didn't do nothing forcing me to restart the phone and restart the batch, until I uninstalled the driver and make Windows reinstall it automatically (manage devices) and it finally flashed it all, actually I flashed the package three times just to be sure lol. So, in the end I wanted to turn off the friggin phone because I was very done with it (what a PITA it has been) and wanted to apply for my warranty so as there is no command in fastboot to shutdown the phone I didn't know how to shut it down so I tried pressing Power button and releasing it the moment the screen goes off but I think I didn't do it right or the phone can't be shutdown that way (this is most probably the answer), well the phone rebooted and by the grace of Zeus it booted for the first time into MIUI and now is waiting for me to configure the phone, none of the times I flashed this packaged into the phone it booted into MIUI, never, and just when I want to turn the phone this thing boots, I don't know if I'm going to venture into flashing anything again being the phone how it is but goddamnit it was a real PITA, I had to use my old Redmi Note 3.
So, tl;dr: Flashed stock package, phone booted finally, all is OK for now.
====================================================================================================
====================================================================================================
Sooo, I was having problems with flashing stuff on this phone but I solved them and I was able to flash HavocOS, it was OK and I could use my phone kinda well (some reboots but nothing serious, or so I thought). So, until 12 hours ago my phone was having problems with the File Manager (I used FX app and also the stock one), it hanged and didn't respond and made the phone reboot itself a couple times, that was weird, actually the whole time I used this ROM I was having problems with my files, it used to took long time to read some files and I was thinking that maybe my SD was bad but apparently it's not. So, after the second reboot I was able to finally open the file manager but navigating through the SDCard was buggy and the app didn't show me any file (it show me an empty list) so I rebooted my phone manually (this time wasn't done by the phone itself) and now is when the phone never passed from the Havoc logo, I waited something close to 30 min and nothing, rebooted and waited 10 min and nothing, it still hanged on the logo, went into recovery to wipe everything and re-flash all and after doing all that and tried to boot to system my phone was booting to recovery and didn't past that, tried installing stock (flash_all script) and then installing recovery and everything again and nothing, it booted to recovery always. So there is when I realized I couldn't change anything in the slot A (at least to what boot refers), I can't install TWRP nor OrangeFox, I can do it in slot B, and even if I boot into recovery on slot B I can flash the zip installer, change the slot and try to boot to recovery from slot A but it boots to the bootloader, and yes, TWRP didn't output any error when flashing the installer.
Yes, the script flashes everything OK, well not everything, system and vendor partitions (A and B) I had to flash them manually because it gave me some errors with the script (reading errors, and yes I compared checksums so it was super weird) but in the end supposedly the stock ROM must have been installed, which I couldn't try because even after flashing everything on the script the phone was booting to bootloader, I didn't give importance to this because before I was able to flash and boot HavocOS I did the same thing because my phone was bootlooping into fastboot: I ran the script, flashed manually those images because it gave me the same errors, tried to boot to system and the phone booted to bootloader, didn't give a sheat, flashed OrangeFox recovery, ROM, recovery installer, GApps, nofde patch and then I was able to boot to HavocOS. But now this time I tried to install TWRP with fastboot command but it didn't worked, fastboot doesn't throw any errors while flashing, it reported:
Sending 'boot_a' (39780 KB) OKAY [ 1.042s]
Writing 'boot_a' OKAY [ 0.208s]
Finished. Total time: 1.263s
But if I try to boot into recovery it sends me to fastboot/bootloader, if I do this in the slot B I can successfully boot into recovery and, as I said, if I flash the installer, change the slot and reboot to recovery, my phone reboots to fastboot.
This has happened to someone else?
Does anybody knows of any solution?
I still have warranty (phone has less than 3 months) so I probably can flash the stock package and lock my bootloader so I can get my phone checked as probably it is a hardware failure, probably and hopefully .
Oh, and also I have to add that the recovery was also lagging sometimes (OrangeFox). Sometimes when I was looking into files on the SD, also when I pressed the "reboot system" button it hanged for half a minute and the it proceeded to reboot, and also once when I was flashing the nofde patch the phone also hanged and rebooted into recovery by itself. So this indicates that maybe is a hardware thing right? Because there is no way that the recovery could have gotten corrupted or something just out of the blue.
Yes. I'm another victim here... And now I can't install recovery on slot b either. Can't figure out what's wrong. This giving me such a hard time...
RthurPendragon said:
Yes. I'm another victim here... And now I can't install recovery on slot b either. Can't figure out what's wrong. This giving me such a hard time...
Click to expand...
Click to collapse
What I ultimately did was wipe everything on slot A, then wipe everything on slot B, then I proceeded to install the ROM on the slot A then re-flash the recovery and reboot to system and that's all. But I did had to wipe both slots A and B. If nothing works you can apply the original ROM (search for it on these forums) and go back to stock.
Jhon_Locke said:
What I ultimately did was wipe everything on slot A, then wipe everything on slot B, then I proceeded to install the ROM on the slot A then re-flash the recovery and reboot to system and that's all. But I did had to wipe both slots A and B. If nothing works you can apply the original ROM (search for it on these forums) and go back to stock.
Click to expand...
Click to collapse
In my case, I wiped system and installed Evolution X ROM (OSS version) with Custom Recovery (SHRP) Then when I want to reboot into recovery again to flash Magisk, There's no recovery... It always opens with fastboot mode. I tried flashing recovery.zip from slot b. Still no result.
Yes. I'm next victim here... And now I can't install recovery on slot b nor slot a. Can't figure out what's wrong. When i flash twrp recovery it flash successfully but when I boot into recovery it stuck in fastboot mode
Change slot and flash again but nothing worked it again stuck in fastboot mode even i flash different version of Twrp(3.2.1) but again it stuck in fastboot mode both a and b slot.
So i flashed stock rom and lock bootloader.
If have any solution how to install custom recovery please help me.
Thanks
Iamdchandan said:
Yes. I'm next victim here... And now I can't install recovery on slot b nor slot a. Can't figure out what's wrong. When i flash twrp recovery it flash successfully but when I boot into recovery it stuck in fastboot mode
Change slot and flash again but nothing worked it again stuck in fastboot mode even i flash different version of Twrp(3.2.1) but again it stuck in fastboot mode both a and b slot.
So i flashed stock rom and lock bootloader.
If have any solution how to install custom recovery please help me.
Thanks
Click to expand...
Click to collapse
Because there are 2 different twrp's.
One of which is for Android 9 and the other for Android 10. You are flashing the wrong one which is why you go to fastboot.
All documentation is on the applicable threads.
People need to stop blindly flashing stuff without reading the documentation or even know what they are doing.
So many people have bricked mi A3 because they don't read first
garylawwd said:
Because there are 2 different twrp's.
One of which is for Android 9 and the other for Android 10. You are flashing the wrong one which is why you go to fastboot.
All documentation is on the applicable threads.
People need to stop blindly flashing stuff without reading the documentation or even know what they are doing.
So many people have bricked mi A3 because they don't read first
Click to expand...
Click to collapse
I have flashed twrp latest 3.4.4 for Android 10 but it is stuck in fastboot mode either slot a or b.
What happened if i downgrade Android 10 to 9 and then flash twrp. Maybe it will successfully flashed.
Iamdchandan said:
I have flashed twrp latest 3.4.4 for Android 10 but it is stuck in fastboot mode either slot a or b.
What happened if i downgrade Android 10 to 9 and then flash twrp. Maybe it will successfully flashed.
Click to expand...
Click to collapse
Don't do it you will mess up your persist partition.
How are you flashing? You must be after typing something wrong
garylawwd said:
Because there are 2 different twrp's.
One of which is for Android 9 and the other for Android 10. You are flashing the wrong one which is why you go to fastboot.
All documentation is on the applicable threads.
People need to stop blindly flashing stuff without reading the documentation or even know what they are doing.
So many people have bricked mi A3 because they don't read first
Click to expand...
Click to collapse
garylawwd said:
Don't do it you will mess up your persist partition.
How are you flashing? You must be after typing something wrong
Click to expand...
Click to collapse
First if all reboot into fastboot mode then connect with pc then type command " fastboot flashing unlock" enter now again forcefully reboot into fastboot mode then type next command "fastboot flashing_critical unlock" now bootloader unlock.
Again reboot into fastboot mode then type command "fastboot getvar current-slot"
Now change current active slot and then type command " fastboot erase boot" . Now finally flashed twrp latest (3.4) for Android 10 with command "fastboot flash boot twrp.img" now it flash successfully then type command "fastboot reboot" and then press volume up then hit enter and it return in fastboot mode then i have again change slot and repeat all process with that slot but it again stuck in fastboot mode. After all i have changed twrp version but again same thing repeat so I flashed stock Android 10 through Mi flash and lock bootloader.
That's all whole process.
If do something wrong please help me to figure out.
Waiting for your reply ?.
Love
try sharp recovery
Sami Devo said:
try sharp recovery
Click to expand...
Click to collapse
I don't know installation process of sharp recovery.
Iamdchandan said:
I don't know installation process of sharp recovery.
Click to expand...
Click to collapse
install on the other slot... dont flash it on running rom slot... if rom running A.. chng it to B. then flash to B.. then goto recovery flash the sharp zip when sharp opens..then again chng slot to A.. running rom slot..
okk ur phn boots.