Mi logo shows very quick then everything goes black - Xiaomi Redmi Note 3 Questions & Answers

Hey,
So I was on CM13 for a long time just updating OTA, everything worked fine.
Today I OTA:d and recieved 7.1.1 (Must be cm14) and when I booted it up after flashing new gapps my fp sensor wasnt working.
So I was doing alot of flashing, I flashed the lib files for goodix and reflashed radon a couple of times to try between the different FP settings.
After that I read that you need to flash the newest firmware for it to work, so I downloaded and flashed the firmware linked on the cm14 strix page, then flash radon on top of that. Keep in mind that I never did any clean rom installs, just installing on top of the rom the whole time.
Now when I tried booting after the new firmware stuff the mi Logo comes up less then a second, it vibrates at the same time as the logo comes up and then it just dies. Like the screen turns off. If i hold the power button for about 10 seconds the same thing happens again. I can't acces my recovery.
The only thing that happens is when I plug in my charger the led light turns red. Could someone please help me?

oggew2 said:
Hey,
So I was on CM13 for a long time just updating OTA, everything worked fine.
Today I OTA:d and recieved 7.1.1 (Must be cm14) and when I booted it up after flashing new gapps my fp sensor wasnt working.
So I was doing alot of flashing, I flashed the lib files for goodix and reflashed radon a couple of times to try between the different FP settings.
After that I read that you need to flash the newest firmware for it to work, so I downloaded and flashed the firmware linked on the cm14 strix page, then flash radon on top of that. Keep in mind that I never did any clean rom installs, just installing on top of the rom the whole time.
Now when I tried booting after the new firmware stuff the mi Logo comes up less then a second, it vibrates at the same time as the logo comes up and then it just dies. Like the screen turns off. If i hold the power button for about 10 seconds the same thing happens again. I can't acces my recovery.
The only thing that happens is when I plug in my charger the led light turns red. Could someone please help me?
Click to expand...
Click to collapse
I can get into fastboot mode too if that helps in any way

The phone says its bootloader is locked in fastboot, will I still be able to flash TWRP via fastboot?

try re-unlock the bootloader via fastboot using mi flash unlock (official unlock), then reboot after success.
hope it helps.

oggew2 said:
Hey,
So I was on CM13 for a long time just updating OTA, everything worked fine.
Today I OTA:d and recieved 7.1.1 (Must be cm14) and when I booted it up after flashing new gapps my fp sensor wasnt working.
So I was doing alot of flashing, I flashed the lib files for goodix and reflashed radon a couple of times to try between the different FP settings.
After that I read that you need to flash the newest firmware for it to work, so I downloaded and flashed the firmware linked on the cm14 strix page, then flash radon on top of that. Keep in mind that I never did any clean rom installs, just installing on top of the rom the whole time.
Now when I tried booting after the new firmware stuff the mi Logo comes up less then a second, it vibrates at the same time as the logo comes up and then it just dies. Like the screen turns off. If i hold the power button for about 10 seconds the same thing happens again. I can't acces my recovery.
The only thing that happens is when I plug in my charger the led light turns red. Could someone please help me?
Click to expand...
Click to collapse
Your bootloader is locked by firmware flashing. You need to unlock it again. Flash MIUI via EDL mode and then unlock. It'll wipe everything.

Just unlock the bootloader as you did in the first.. DO not flash the latest cm 14.1 firmware.. it relocks the bootloader.. check for modified firmware in CM14.1 thread.. it will boot without any issue... Had same issue.. using tesla now without any issue..

Try to unlock bootloader and see. If it does not help you need to flash MIUI Rom using EDL mode. I too get same problem sometime when flashing and trying various custom ROM and only method worked for me is flashing MIUI Rom again using EDL mode and than flashing other custom Rom again. All the datas will get wiped when you flash using EDL Mode. Hope it will help You.

oggew2 said:
Hey,
So I was on CM13 for a long time just updating OTA, everything worked fine.
Today I OTA:d and recieved 7.1.1 (Must be cm14) and when I booted it up after flashing new gapps my fp sensor wasnt working.
So I was doing alot of flashing, I flashed the lib files for goodix and reflashed radon a couple of times to try between the different FP settings.
After that I read that you need to flash the newest firmware for it to work, so I downloaded and flashed the firmware linked on the cm14 strix page, then flash radon on top of that. Keep in mind that I never did any clean rom installs, just installing on top of the rom the whole time.
Now when I tried booting after the new firmware stuff the mi Logo comes up less then a second, it vibrates at the same time as the logo comes up and then it just dies. Like the screen turns off. If i hold the power button for about 10 seconds the same thing happens again. I can't acces my recovery.
The only thing that happens is when I plug in my charger the led light turns red. Could someone please help me?
Click to expand...
Click to collapse
d
u bricked your device... flash fastboot rom and unlock the bootloader.

Related

Xperia U won't boot. Help needed

Hello.
I have rooted the xperia U using the flashtool by following a guide available on xda. Everything worked fine. I wanted to install a custom rom for which I had unlock my bootloader and flash a custom recovery for flashing the rom. I downloaded and flashed cwm. So I unlocked the bootloader using the official method, i flashed the boot.img of the custom rom(in fastboot) and tried to go to recovery, but my phone wouldn't switch ON now.
I was able to make it reach flashboot mode(green) and tried flashing ftf.. Even that's not working.
The service update software is not even detecting my phone.
Please help.:crying:
When you say, not switching on, can you feel it vibrate when you push the power button?
Also whats the error you receive on flashtool?
Yes, i do
But the screen is blank and I can only see the red notification light
rohitbalan said:
But the screen is blank and I can only see the red notification light
Click to expand...
Click to collapse
May be you flashed wrong kernel, which is not for your phone.
Try to charge the phone for a few hours and after thats try flashmode again to flash stock rom...
same problem
Actually I am facing the same issue u had with your Sony xperia u. Please help.
Charge the battery, seems gone flat. Leave it on charge for half an hour or so. If that doesn't work maybe the software is corrupted to the point it doesn't cold boot to charge, so charge battery separately using external charger for half an hour or so. It should be able to boot at least to flash mode (Vol Down + Power).

Phone bricked after CM 14.1 update - cant access fastboot

Hi,
i woke up this morning and the CM updater offered me to update for CM 14.1, i thougt welll, why not. mistake :crying:
Now the phone is stuck on the flashing CM logo,
if i try to go to fastboot, than i see the fastboot screen and than black screen and the phone goes back to the flashing CM logo.
Any thoughts?
guytsur7 said:
Hi,
i woke up this morning and the CM updater offered me to update for CM 14.1, i thougt welll, why not. mistake :crying:
Now the phone is stuck on the flashing CM logo,
if i try to go to fastboot, than i see the fastboot screen and than black screen and the phone goes back to the flashing CM logo.
Any thoughts?
Click to expand...
Click to collapse
do u have access to recovery?? if u have, then u can just flash previous build without wiping data..
Think if you press vol+ vol- and power and then use the button combo to boot into TWRP you will be fine, takes abit of messing to get it right.
http://en.miui.com/thread-277276-1-1.html
TRY THIS
saikatmitra71 said:
do u have access to recovery?? if u have, then u can just flash previous build without wiping data..
Click to expand...
Click to collapse
Did you try this solution? Did it work? Did you lose your apps/data?
Solved
Eventually managed to get onto twrp using adb (it was a bit of a statistical process... Didn't always work)
From there I just flashed cm 14.1 again, and it looks OK now
Thanks you all for the help!
Like I said earlier failed flash by CMxx doesn't overwrite TWRP, you can boot back into recovery just have to try a few times. Happened to me pressing both volume buttons and power switched phone off then I used button combo and it booted into TWRP.
Might have to grab a usb cable and use ADB to boot into fastboot. It happened to me and that was the only way for me.
seos83 said:
Might have to grab a usb cable and use ADB to boot into fastboot. It happened to me and that was the only way for me.
Click to expand...
Click to collapse
Don't worry Follow This one No fastboot, no edl, no test point, best way to Recover Xiaomi Device, prepare by me and 100% working {tested}

boot loop flare s play

anyone can help me? I've tried to root my cherry mobile flare s play, I've flash twrp on it but it always boot in recovery it doesn't boot in system partition so I tried wiping the cache and dalvik cache, still doesn't boot so I tried flashing another recovery/rom and it just get worst it's now stuck in boot loop I've already tried the abd reboot-bootloader and always fall in error: device not found., I hope someone notice my case. thanks
Hello, this happens when the system is actually corrupted
you may reflash stock then twrp then root again
or just get a custom recovery for your device
you must go in bootloader for stock rom or twrp for custom rom, and that's fine your phone just needs a rom and its good to go
good luck
TheShadowMC said:
Hello, this happens when the system is actually corrupted
you may reflash stock then twrp then root again
or just get a custom recovery for your device
you must go in bootloader for stock rom or twrp for custom rom, and that's fine your phone just needs a rom and its good to go
good luck
Click to expand...
Click to collapse
but how can I boot it on bootloader? key combinations like vol+ and power or any combo doesn't work, only if someone can teach me how to boot it on bootloader or fastboot then there would be no problem for me, I don't know what to do now
Hello again, take out the bettery then put it back and use the bootloader combo
if it didnt work take out the bettery and flash through sp flash tool
nothing to worry about, i didnt notice that your phone can be flashed through sp flash, since it just requires the phone to be off
not really such a scary situation
TheShadowMC said:
Hello again, take out the bettery then put it back and use the bootloader combo
if it didnt work take out the bettery and flash through sp flash tool
nothing to worry about, i didnt notice that your phone can be flashed through sp flash, since it just requires the phone to be off
not really such a scary situation
Click to expand...
Click to collapse
will it work even if my device don't have battery on it?
kiltot24 said:
will it work even if my device don't have battery on it?
Click to expand...
Click to collapse
sp flash for my knowledge would work even when the battery is out it doesnt matter, just load the scatter press download button and connect the phone with battery off
good luck again:highfive:
-Hope- said:
sp flash for my knowledge would work even when the battery is out it doesnt matter, just load the scatter press download button and connect the phone with battery off
good luck again:highfive:
Click to expand...
Click to collapse
in my case I can't flash even a recovery image using sp flash tool. any help? sorry if I look like an ignorant any way thanks for your help guys, I really appreciate
no no problem, however what's the problem ?
I'm trying to flash a custom recovery on it but it doesn't work, I'm trying to flash twrp, the one I've flash before, because I don't have the stock rom of my device so I'm doing the process partially. I'm aiming to flash twrp and then restore my saved back up.
Hello,
i think your device stock frimware is there on google, however when you try to flash what error does it give or what happens ?
It doesn't show any error message and not showing any progress at all. my device just blink showing that the battery is charging though the battery is not present.
if it didnt detect it try pressing the volume up or volume down to make sure while connected ( and download button is pressed
just blink until it reaches time out.
I'm sure that my cable is working, it works on other device. I already install all the drivers I need.
is there a way to stop my device from simultaneous booting? it appears to be detected on device manager but just for a few sec, then reboot and appear again.
ensure the ROM is loaded properly in the flash tool.
Switch off the phone and remove battery.
press the start button in the flash tool to initiate the ROM flashing process. The process will be in hold, waiting for the phone to accept the new firmware.
Now connect the phone to computer.
Try these. Press and hold VOLUME DOWN OR VOLUME UP OR POWER+VOLUME UP OR POWER+VOLUME DOWN. One of these should work and the flashing process should start.
can I obtain the stock rom from the same device? I have the same model and it works properly. I can't download the stock rom from mediafire it always fail due to poor internet connection so I'm looking for another way.
I tried updating my driver then my device was recognized but when I flash the recovery image it displays 100% but in red color.
kiltot24 said:
I tried updating my driver then my device was recognized but when I flash the recovery image it displays 100% but in red color.
Click to expand...
Click to collapse
are you using the latest sp flash tool ?
yes thanks my device works fine now thank you for your help, the only problem now is how will I restore my device imei, it can be changed in engineer mode using at+ command but it be deleted again once conduct a factory reset in short it just set a temporary imei for my device, is there a way to change my device imei permanently?

(HELP) Note Edge N915G- infinite three seconds boot loop

Hi everyone.
Got Note Edge N915G which was running fine with Micky's MM ROM V3. As there was one problem- low incall volume in the ROM, I decided to revert to Stock firmware yesterday. Accordingly, I flashed Stock Firmware with Odin 3.12. Flashing went fine with Odin but I got this infinite bootloop. I am having this cycle of Phone turning on and logo appearing for two seconds and turning off again. I cannot go to stock recovery (shows <blue> "recovery booting' message and phone turns off) but can go to download mode fine.
What I have done so far:
-Flashing different versions of stock firmware (Lollipop and Marshmallow) by Odin 3.12. It completed with "Passed" message but the problem remains the same.
-Flashing by Samsung Smart Switch application. It completed 100% but the problem is same.
-Flash TWRP recovery by Odin. Then tried to install Micky ROM again but it could not complete. Device switches off at the stage of flashing of "system.img"
-Flash custom kernal also but no good.
-Thought it might be "Power button" problem, tried to soft press it various ways. But it does not seem so.
I have been flashing custom ROM for some time and thought I am good at it. But I cannot get the idea what the current problem is. So I would appreciate someone please help me out.
saviour555 said:
Hi everyone.
Got Note Edge N915G which was running fine with Micky's MM ROM V3. As there was one problem- low incall volume in the ROM, I decided to revert to Stock firmware yesterday. Accordingly, I flashed Stock Firmware with Odin 3.12. Flashing went fine with Odin but I got this infinite bootloop. I am having this cycle of Phone turning on and logo appearing for two seconds and turning off again. I cannot go to stock recovery (shows <blue> "recovery booting' message and phone turns off) but can go to download mode fine.
What I have done so far:
-Flashing different versions of stock firmware (Lollipop and Marshmallow) by Odin 3.12. It completed with "Passed" message but the problem remains the same.
-Flashing by Samsung Smart Switch application. It completed 100% but the problem is same.
-Flash TWRP recovery by Odin. Then tried to install Micky ROM again but it could not complete. Device switches off at the stage of flashing of "system.img"
-Flash custom kernal also but no good.
-Thought it might be "Power button" problem, tried to soft press it various ways. But it does not seem so.
I have been flashing custom ROM for some time and thought I am good at it. But I cannot get the idea what the current problem is. So I would appreciate someone please help me out.
Click to expand...
Click to collapse
Ummmm..........maybe your bootloader is your problem. i remember in 2014 my note 2 same problem as your.
When i update to 4.4 custom rom i need to back to 4.3 because of doesn't work the wifi so i back and boom...bootloop, i forgot to flash the firmware and bootloader and hey is working again.
So maybe you should Try out.
Sent from my Pixel 2 XL using Tapatalk
JohnMichaelCost said:
Ummmm..........maybe your bootloader is your problem. i remember in 2014 my note 2 same problem as your.
When i update to 4.4 custom rom i need to back to 4.3 because of doesn't work the wifi so i back and boom...bootloop, i forgot to flash the firmware and bootloader and hey is working again.
So maybe you should Try out.
Sent from my Pixel 2 XL using Tapatalk
Click to expand...
Click to collapse
Thanks. Now I wipe out everything from the mobile. I Initiated software recovery process from the Smartswitch. The process completed to 100%. But still I am stuck in the bootloop. Now, device turns on, show blue "recovery booting" and samsung logo then turns off. It goes on repeatedly. Please suggest what to do...
saviour555 said:
Thanks. Now I wipe out everything from the mobile. I Initiated software recovery process from the Smartswitch. The process completed to 100%. But still I am stuck in the bootloop. Now, device turns on, show blue "recovery booting" and samsung logo then turns off. It goes on repeatedly. Please suggest what to do...
Click to expand...
Click to collapse
You should maybe take to samsung store to fix your phone.
Is my final answer can't helping your phone because i dont have a note edge/4 talk to the admin or samsung developer.
Sent from my Pixel 2 XL using Tapatalk

Redmi Note 9 Pro bricked after flashing with Mi flash Tool

Hi Guys, so the things I was using the official AOSP extended rom on my Redmi Note 9 Pro after but after ccouple of days changed my mind wanted to revert back to the official MiUi rom. So used the Miflash Tool to flash "joyeuse_global_images_V12.5.4.0.RJZMIXM_20220215.0000.00_11.0_global" after flashing it reported a failed error and the fastboot screen started flashing on and off. After turning off the phone and pressing the power button to turn the phone flashes the redmi logo for less than a second and turns off. Plugging in the charger makes the phone flash Redmi logo and then turn off again repeatedly. I can neither get into fastboot mode nor into recovery. Is there any solution to this problem? Any help will be much appreciated. Below is a short clip of the problem.
Abir172 said:
Hi Guys, so the things I was using the official AOSP extended rom on my Redmi Note 9 Pro after but after ccouple of days changed my mind wanted to revert back to the official MiUi rom. So used the Miflash Tool to flash "joyeuse_global_images_V12.5.4.0.RJZMIXM_20220215.0000.00_11.0_global" after flashing it reported a failed error and the fastboot screen started flashing on and off. After turning off the phone and pressing the power button to turn the phone flashes the redmi logo for less than a second and turns off. Plugging in the charger makes the phone flash Redmi logo and then turn off again repeatedly. I can neither get into fastboot mode nor into recovery. Is there any solution to this problem? Any help will be much appreciated. Below is a short clip of the problem.
Click to expand...
Click to collapse
Can you post the log of Miflash?
Here's the log of the flash.
NOSS8 said:
Can you post the log of Miflash?
Click to expand...
Click to collapse
According to the log, the flash was successful, the error is normal (6:02:45 PM 9f886790]:error:Not catch
checkpoint (\$fastboot -s .* lock),flash is not done) since you did not lock the bootloader (flash_all.bat).
After the flash the phone reboots automatically, did you interrupt it?
First try to see if a button is not defective, a bit of WD40 product for example and operate it several times.
But if it worked well before it would be a strange coincidence but it is possible.
(I had this case on one of my phones by dint of flashing).
Hi sir I have this problem too
elinajafi said:
Hi sir I have this problem too
Click to expand...
Click to collapse
Can you post the log of Miflash?
It seems like a common issue happens with me when I try to flash stock rom via fastboot, if you ever been able to enter fastboot flash custom recovery (like twrp) and use it to flash the stock rom zip (recovery method), it should work..

Categories

Resources