after a hard bricked episode i had ,which i fixed but damaged the cable that connects the screen with the <motherboard> i can charge, turn on and off and vibrations when I press the screen which it seems to respond but its just black .I can hear sounds unlock raise volume even my alarm this morning BUT NO IMAGE..... i damaged a bit this cable where it connects at the end( the big one in the middle of the pic)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
the screen IS NOT damaged ,so my question is can i fix it without replacing the WHOLE screen??
Related
Today i opened microusb flap and i saw red dot like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Water damaged?Warranty Bye bye?
No its a physical shut down button. you can press it for some seconds (e. g. with a pen), device should vibrate 3 times and shut down. (Same effect when holding volume up and power button for some seconds)
I think water indicators will be inside the device.
Thanks.On the bottom is white paper.Great
The water damage indicator is under the sd card port, you can barely see it but that's where it is.
hii i was unable on turn on my s6 edge last time ran out of battery putted for charging while cell is off after getting 70% charged pressed the power on button but nothing happend black screen and white solid light
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi , I'm unable to see the picture because you are new member , can you send me private message .
My phone screen randomly changed to this:
I didn't damage my screen or anything. Was working perfectly an hour ago. Is there any way to fix this myself?
Someone on youtube repaired a p20 with the same issue but he replaced a data filter. I dont know if this can be done at home by a complete amateur.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
While replacing screen, I broke a RF plug on the motherboard (I think so) - attached an image ( a thick black cable between motherboard and charging plate
). Someone knows how can I fix that?
for what is the cable responsible ?
After the screen replacement the Load Speaker also stopped working, there is any connection between that plug and speaker?
or I just broke my speaker too and replacement will fix that?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I had to replace the battery of my Z4T. Removing the display and replacing the battery went fine. Unfortunately when connecting the cable to the display, the connector broke (see attached image). The conncector on the right hand side is in order (see arrows). For the connector to the left the black part is broken and it can not be closed to fix the cable. Is there
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
a way to attach the cable without this black part? Otherwise I would need to replace the display (which is fully functional).