My Xbox 360 was working perfectly connecting to my router and now, all of a sudden, it says it cannot connect. I am plugged directly into the same RJ45 port I have always been plugged into.
Here is what I have done since then.
I plugged my laptop into that same port with the same cable, turned of the laptop's wifi and the internet works fine.
Power cycled my router
Changed the Xbox 360 to manual IP and DNS instead of Automatic.
Related
I guess I'm a total noob. I rebooted the tablet and now the 360 controls work fine! FFS
Read on if you want to know what the problem was...
I have tried to use my xbox360 wireless controller with wired PC dongle and a xbox360 wired control in the USB port of the dock and the wireless dongle lights up only when i push the button then i sync the control and the light goes off and the control wont map in any of the emu's or games I tried where the WII-mote worked. The wired one doesn't even turn on (flickers on then off .2 sec) when plugged in. Am I missing something do I have a defective doc? I also happen to have a ps3 control and that also doesn't work with the USB cable and the six-axises app. App says its compatible with the Transformer Prime but it always just asks me to pug the USB in even tho its plugged in. Any ideas? Does the Dock need a certain amount of charge does it have to be plugged into the wall to have enough power? Wireless dongle light goes off after the control is synced, is that normal? Could it be because its rooted?
(4.0.3 ICS brand spanking new Transformer Prime w/ wired 360 control, wireless PC dongle & wireless 360 control, and PS3 control with USB wire and Six-Axises app plugged to dock with no success)
Did you fix this? I have the same issue.
I have a two week old unrooted red 300 on 4.1.1 with dock, I already had a ps3 with controllers so my controller was previously paired with ps3 ( which may be the problem). As long as I have it connected via usb to my dock it works fine, but when I disconnect the controller shuts off. I see on youtube people just connect via usb, disconnect the usb and viola, playing bluetooth but mine is not working, is there any steps or apps that I need to have before I can play wirelessly. oh and yes my bluetooth is on lol.
akareem27 said:
I have a two week old unrooted red 300 on 4.1.1 with dock, I already had a ps3 with controllers so my controller was previously paired with ps3 ( which may be the problem). As long as I have it connected via usb to my dock it works fine, but when I disconnect the controller shuts off. I see on youtube people just connect via usb, disconnect the usb and viola, playing bluetooth but mine is not working, is there any steps or apps that I need to have before I can play wirelessly. oh and yes my bluetooth is on lol.
Click to expand...
Click to collapse
There shouldn't be anything special you need to do. Plug in the USB, with bluetooth on, hit the PS3 button to turn the controller on and the Bluetooth should connect with it. Double-check in the Bluetooth devices that it shows a PS3 Controller listed in the paired devices after performing the above steps.
When you disconnect the USB cable it should disconnect and turn off the controller. Just hit the PS3 button again and the lights should indicate a flash showing it's on and then switch to connected at controller 1 and the bluetooth devices will show connected in the ASUS settings.
-Nate
Hi, I have a MK808 which I have connected to a usb to ethernet converter. I boot directly into XBMC, but the ethernet connection can be a little flakey. Sometimes on boot it connects to the ethernet fine but other times it doesn't and I need to go into setting and switch the ethernet off and back on and that works.
My idea is to have tasker switch the ethernet off and on just after booting so that I can be assured it would work every time, but I can't see any ethernet option in tasker does anyone know a way of doing this.
Thanks
BW
I am running stock Lollipop and have purchased an Ethernet adapter (www.amazon.com) which has been reported to work via some videos I watched on YouTube. So I turn off the Shield and plug it, turn on the Shield and watch my router. The activity LED on my router lights up for a few seconds and then turns off. I don't use DHCP so I don't know if that is an issue, but when I get into Lollipop I can't seem to find a way to configure the Ethernet adapters IP address. How do I go about configuring the IP settings?
When I connect my ipega 9021 to pc it connects but disconnects after e few seconds. After e few re connecting controller connect properly but not working. Controller work on my phone with out any problems. Any solutions?