i tried to upgrade my m9s pro to kodi 17 via apk file...when i tried to install the apk, the installation failed and my box froze...i waited for like 10-15 mins to see if it comes back to normal...but it remain froze...
I unplugged the power and plugged back in to restart it...and then the box was stuck at red light...BUT BUT BUT...after exactly 15 mins or so, the blue light used to turn on with m9s pro logo...and it remained stuck there...
I tried restarting it for few times but always at the start, it was stuck on red light...then after 15 mins blue light turned on n thn stuck on m9s logo...
I searched on the internet and read somewhere to hold the reset button while plugging in the power...i did that and i went into a screen with green android man and at the bottom there were commands like > formatting data, e: can't mount etc etc...
After those commands the box restarted and ever since, the box stays on red light and it does not shows the blue light even after 15 or 30 mins ...or even an hour....
i wished i would have tried flashing when it was on blue light....but now as it is stuck on red light...need to do something...
I am using the correct firmware - that i am sure...because the firmware mentioned on this firmware for this box, and the firmware my supplier sent is the same.
While flashing i get below errors, Do you have any idea regarding the below error,
[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
This error comes at 2% and when i only connect the box with laptop using usb...
And the below error comes when i connect both usb n power cord to box and then connect it to laptop,
uboot/disk intialize/send command/error result
This error comes at 7% when formatting is about to start...
I have tried on windows 7 & 10 laptop + pc....Used almost every version of usb burning tool...the usb cable i am using is 1 metre approx...
Any help will be appreciated....
Related
Hello XDA,
Its one of my first threads. I always read the threads and post first. No matter what, i always try to find the answers by myself by lurking in each and every thread... so please help me out on this one this time.
TOPIC: SONY XPERIA SP IS NOT BOOTING UP (BOOTLOADER UNLOCKED)
REASON: I DID A SYSTEM WIPE IN CWM:silly: becoz my gapps for some unknown reason ceased to sync and i wanted to remove gapps.
THE CASE: After wiping system partition in CWM i rebooted my device. It booted and the Sony logo appeared. AND IT STUCK. Period. I did a HARD RESET (pinned the hole up until 3 vibrations). The mobile shutdown and then never booted up.
I tired to enter FLASHMODE and flashed the stock FW. But it failed everytime with a msg that USB DEBUGGING is off (now how on earth do i turn on the debugging if my fone is not booting up.) and i remember very thoroughly that my USB DEBUG was on before the brick.
CURRENT SITUATION: My phone just does not repond to power button whatsoever. I kept it unplugged/unchrged for more than 40 hours as my users suggested to clear the bad data off the chip.
Whenever plugged in the wall charger it gives up a strong RED LED and then after sometime that changes to GREEN LED . Then the GREEN LED goes by itself and a constant RED LED comes.
I AM UNABLE TO GET INTO FLASH OR FAST BOOT MODE. IT JUST GIVES A RED LED WHEN I PLUG IN THE PC USB:crying:
Hello XDA family
So, i'll start from the beginning of my issues with my xperia Z2, allmost two weeks of reasearch but nothing. I bought this phone preused and with broken digitizer, fixed everything and turned it on, booted up and everything was fine. Phone offered update wich i did and it was the beginning of my troubles. Boot loop was first thing, and few other things wich lead me into buying new genuine battery. I literally spent a day to get out of boot loop by disconnecting the battery, tried to reset and all sorts of thing and still don't know which of those many things actually worked but i got it booted up finally.
So yesterday i took it out of the box again and thought to update it to latest 5.1.1 Lollipop via wifi because i can't get phone into flashmode, so while installing update (android logo with blue loading line) my phone turned off. I turned it on again and same thing, android logo with blue loading line half done and turned off, and again and again. Finally disconnected the battery, connected usb cable to the wall charger, connected battery and red light poped on, so i let phone to charge, after few hours i turned my phone ON and voila, somehow i got latest android installed.. go figure.
When i bought this phone the rear camera didn't work, i saw the icons but didn't take any picture. Did cache clear and other tricks i found from google but nothing works, im not sure but i guess this issue came when last owner updated it from kitkat to lollipop.
So heres my biggest problem, to downgrade z2 to kitkat i need to flash it, but i can't..
When phone is on my pc will recognize it.
When power + VolDown, green led pops on (flashmode) and after few secons i get usb device not recognized. (Tryied some tricks that i found from google, no succsess)
When power + VolUp, blue led pops on (fastboot mode) and flashtool is actually connecting with the phone like it's suppose to be.
Im using Flashtool Version 0.9.19.8 and all necessary drivers are installed, included sony ones. I also Tried different usb ports and different pc, same thing.
MakuAr
Hi,
My phone turned off.
I don't think my battery was empty, but can't be sure.
When I plugged it to recharge, the led was blinking fast, and the big battery icon didn't show up.
I never could turn back my phone on.
I've read here and there that it could be a battery issue.
I've opened the phone, unplugged the battery and connected the phone to my pc. It turns on, but bootloops every 3-4 seconds (Mi logo shows up, then it vibrates and reboots).
I tried plugging the battery back with the Mi logo on, but then the led starts blinking and the phones stops looping (turned off).
I managed to boot into fastboot by holding the - button and plugging the usb. Running adb devices doesn't show anything. Yet there is no error when trying to flash twrp through adb.
I managed to boot into twrp (so it was actually flashed, because I had orangefox recovery before the crash.
Yet in twrp, the note 5 plus folder is empty. I tried to mount usb, nothing too.
I tried to backup via adb twrp, and I got a bunch of errors ("unable to mount data", "unable to mount storage", ... then a bunch of "e:recv error on uevent").
Any idea what I can do ?
Is it the battery ? Don't really want to buy a new battery if i't not sure it's the problem.
I had to buy a new phone in the meantime, so I mainly want here to recover data (pictures mostly) from my phone.
Thanks !
Hi
my box not working when plug its only red led
try to flash diferent firmwares, with UBT several versions and settings - but got errors on 7% time out or 8%
from SD card i got blue led and upgrading screen but its not going anywhere (wait for an hour...)
herer is pictures of the device
Help please is its totally dead?
My phone is stuck in the "Downloading...do not turn off target" loop.
I get the following error message at the top:
ODIN MODE [UT Load Fail)!
[UFDT] DT Entry: Not found rev 0x10
[UFDT] DTBO LOAD FAIL
I've tried holding power+vol down for 7 seconds, it just loops back to this screen over and over again.
The device isn't detected by my PC when I plug it in via USB cable.
Now the screen has turned green, with lots of white flashing, with the downloading screen barely visible underneath.
Has anyone solved this issue before?
Our family was together for the first time in years a few days ago and all the photos are on the phone I back up regularly, but it was only a few days since our time together and normally do it first of the month.