I wanted to create a thread to collect everyone's findings and opinions on what the best screen protector for the S8 is.
From what I have found there are:
- TPU dry application
- TPU wet application
- tempered glass glue only at sides
Post what you think the best protector is for feel, sensitivity and coverage. Also how compatable with cases and ease of application.
So far I've tried the amFilm from techmatte. Glue is viable around the sides and the touch sensitivity is reduced after insalll.
Master List - Tempered Glass
amFilm By Techmatte
Tempered glass, glue round the outside and top of the protector only. dot matrix on the screen for better sensitivity.
Glass feels nice but leaves loads of fingerprints and it is really reflective to light. Reduced sensitivity especially at the top. Works well with cases as its not quite full coverage.
Master List - TPU Films
yootech
Wet apply. Went on easy, works well with case no lifting. Feels nice.
Techgear ghostshield
Dry install. Kinda hard install as top part has separate protective film to the rest so it's hard to remove tbe main bit without getting dust under the protector. Sticks to the sides well. Clarity is bad, makes the phone look greasy /oily. Touch sensitivity is unaffected.
I bought these and it went on really easy, no bubbles and doesn't lift around the edge like a previous protector I used did when I put my Spigen Thin case on, feels ok to use too
https://www.amazon.co.uk/dp/B071R5P7QN/ref=pe_385721_37986871_TE_item
EDIT - This is the previous protector I used, I found it reasonable to apply but lifted around the edges when putting my case on
https://www.amazon.co.uk/gp/product/B01MZ9L4WG/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
MilgeS said:
I bought these and it went on really easy, no bubbles and doesn't lift around the edge like a previous protector I used did when I put my Spigen Thin case on, feels ok to use too
https://www.amazon.co.uk/dp/B071R5P7QN/ref=pe_385721_37986871_TE_item
Click to expand...
Click to collapse
Got one of these on order due Wednesday. Looking forward to this as it's wet install. I'm currently usi g Ringke Slim case
Sent from my Galaxy S8 using XDA Labs
Hi, yes it does, just stops 1-2mm short of the edge of the glass all around. I hope you like it
The Whitestone Dome Glass seems to be getting alot of attention. See the following video review:
Part 1:
https://www.youtube.com/watch?v=N8nBUAb9x44
Part 2:
https://www.youtube.com/watch?v=-fbZ9HtcYOA
Official Site:
http://whitestonez.com/
SlyUK said:
The Whitestone Dome Glass seems to be getting alot of attention. See the following video review:
Part 1:
https://www.youtube.com/watch?v=N8nBUAb9x44
Part 2:
https://www.youtube.com/watch?v=-fbZ9HtcYOA
Official Site:
http://whitestonez.com/
Click to expand...
Click to collapse
I have this one on my phone and my girlfriends ( both of us have the S8, not the plus).
I have a case on mine and it fits very well and doesn't interfere whatsoever.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my SM-G950U using Tapatalk
Got me a protector from Five and Below. Works great and doesn't lift off screen inside of case.
This is another Korean company that maybe worth looking at:
http://www.amazingat.com/
Hawke84 said:
Master List - TPU Films
yootech
Wet apply. Went on easy, works well with case no lifting. Feels nice.
Click to expand...
Click to collapse
How does it feel? Some reviews said it's too rubbery. I'm finding it so hard to find a protector I know I'll like
daddymikey1975 said:
I have this one on my phone and my girlfriends ( both of us have the S8, not the plus).
I have a case on mine and it fits very well and doesn't interfere whatsoever. View attachment 4136076View attachment 4136077View attachment 4136078
Sent from my SM-G950U using Tapatalk
Click to expand...
Click to collapse
Same here, no touch issues, looks awesome and works with a lot of cases. I'm using it with uag plasma and monarch.
Amylittlehands said:
How does it feel? Some reviews said it's too rubbery. I'm finding it so hard to find a protector I know I'll like
Click to expand...
Click to collapse
Forget yootech, it works well the first 1-2 days but then you have to repress on the borders every day because the TPU cover lift it, and now after 10 days some parts are not gluing anymore specially the bottom corners.
Feeling is plasticky and a bit sticky, not as good as ''dry'' films
vegetaleb said:
Forget yootech, it works well the first 1-2 days but then you have to repress on the borders every day because the TPU cover lift it, and now after 10 days some parts are not gluing anymore specially the bottom corners.
Feeling is plasticky and a bit sticky, not as good as ''dry'' films
Click to expand...
Click to collapse
Ah darn. I still have the chappy film that came with the phone on. I've had so many protectors on phones and none of them are good enough
Amylittlehands said:
How does it feel? Some reviews said it's too rubbery. I'm finding it so hard to find a protector I know I'll like
Click to expand...
Click to collapse
Actually really like the feel. Doesn't feel too rubbery. It's not glass but it's quite smooth as long as you don't dig your nails in. I forget it's there a lot. Took me a while to apply and get it right but not had any edge lifting. I am using a case so that may help.
Sent from my Galaxy S8 using XDA Labs
I can whole heartedly recommend these ones:
https://www.amazon.co.uk/gp/product/B06XY7K875/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
They are the film variety, but PET film, so no rubbery feel. These also benefit from being slightly curved at the edges (much like the TGSP's) so fit perfectly, with no lift. Have been using mine for 3 weeks now and its still firmly stuck on all edges, NO LIFTING!! And best of all, they work with cases too. Currently using it with a slim case, but it fits my Spiegen Neo Hybrid with no problems. And did I mention you get 3 in a pack. *drops the mic....walks off stage*
All jokes aside, these are a really good solution for screen protection with very few drawbacks.
P.S I do not work for this company nor is this recommendation being endorsed. Just passing on some invaluable knowledge to hopefully prevent someone else from buying almost every single variety of screen protector available.....not that I did that.....much.
honestly this screen protector thing is so long winded, and only for this phone as for all the others its been easy
there should be a section for uk screen protectors as we cant buy certain ones like the whitestonez version
finally got hold of this phone and cant decide what protector to get, has to be a good one as the screen is what it all is about
bm_99 said:
honestly this screen protector thing is so long winded, and only for this phone as for all the others its been easy
there should be a section for uk screen protectors as we cant buy certain ones like the whitestonez version
finally got hold of this phone and cant decide what protector to get, has to be a good one as the screen is what it all is about
Click to expand...
Click to collapse
You can get the Whitestone in the UK from Mobilefun.co.uk but it's £68 a ridiculous price!
Batfink33 said:
You can get the Whitestone in the UK from Mobilefun.co.uk but it's £68 a ridiculous price!
Click to expand...
Click to collapse
damn, lol max i would spend it probably £20.
there should be a vote on the best ones available and where from for country specific versions i think as its all to confusing if someone from usa posts a protector with really good reviews but we cant even get them
This is the screen you are all looking for. Im using it. Its awesome. Trust me i feel your pain.
[Tray Installation]Samsung Galaxy S8 Screen Protector, OTAO [Case-friendly] Tempered Glass Screen Protector with Positioner For Galaxy S8 (S8) https://www.amazon.com/dp/B071PB2KP2/ref=cm_sw_r_cp_apap_v5NWvthJmWDmp
Related
So tomorrow i'm getting my Lumia, and i was wondering if it was possible to apply a genric screen protector on it while i wait for the specific one i ordered. Do they actually stick on this particular curved glass screen? What should i use for the moment? I don't wanna end with this bad boy scratched in just a couple days...
Even since my Blackberry days, I have always used screen protectors. This phone represents a big departure for me from that..
I have a belt carrying case or I'll carry the phone in a sort or jacket pocket after making sure nothing else is there.
Carrying in pants pocket is out of the question..
To me the glass and the coating are part of the design of the phone and in this case the shape and texture of the naked screen is what really makes this phone stand head and shoulders above iPhone, Samsung Galaxy or any other higher end peers.
In my opinion, adding any protector in addition to
the silicone case Nokia provides would really take that advantage away and dumb the phone down..
Yeah i feel that too, but you know i'm an offroad rider and the place i live also has some quite sandy ground...i've always managed to scratch every surface i was carrying with me, even the sapphire cristal of my good old Sector watch, so i'll be always too scared to carry a phone naked, especially if it's so damn beautiful...i'm a dangerous man i guess
I bought a Nillkin screen protector and even though it works really well, the cutting is only till the border of the actual screen. It does not go till the edge where the polycarbonate body begins.
So conclusion is that it sucks. I will be interested in any other screen protector anybody has tried which can reach till all the four edges of the screen.
chaihg said:
I bought a Nillkin screen protector and even though it works really well, the cutting is only till the border of the actual screen. It does not go till the edge where the polycarbonate body begins.
So conclusion is that it sucks. I will be interested in any other screen protector anybody has tried which can reach till all the four edges of the screen.
Click to expand...
Click to collapse
Use those flexible protectors like Invisishield/BestSkinsEver etc. You can stretch it while applying.
Is a screen protector needed? This phone is fitted with gorrilla glass...
i have to admit my screen gets immensely greasy - i don't think it has any kind of anti smudge coating on it. at least mine didn't - i haven't seen anybody else's one.
Every screen irrespective of it being a Gorilla or Chimpanzee needs a protector. If you have sensitive eyes you can make out minute microscopic scratches that form in an arranged fashion after 2months of use. I hate it.
I am still looking to see if there is any protector out there that can fit edge to edge. Shucks with all the technology out there people cant make a thin plastic sheet that fits a curved screen ??
Skinomi's protections cover the whole screen. I purchased one, and quite happy about it. Fits perfectly egde to edge. It's not a rigid plastic protection like the cheap chinese ones, it is flexible and bends naturally on the curve.
You can find it on Skinomi's website, thought I think it is cheaper on amazon (like $6 or $7).
Don't worry about the picture you may find (which is one of an N9 screen protection) there is only one hole for the sensor on the actual protection.
Happy to answser any questions...
Heldorn said:
Skinomi's protections cover the whole screen. I purchased one, and quite happy about it. Fits perfectly egde to edge. It's not a rigid plastic protection like the cheap chinese ones, it is flexible and bends naturally on the curve.
You can find it on Skinomi's website, thought I think it is cheaper on amazon (like $6 or $7).
Don't worry about the picture you may find (which is one of an N9 screen protection) there is only one hole for the sensor on the actual protection.
Happy to answser any questions...
Click to expand...
Click to collapse
Hey thanks for that tip. Is it possible even with the any camera you have to take a small pic of your phone with that protector and post it here. That will be the decisive pic for this topic.
Best shot I could get. It is almost invisible anyway.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
About the installation, the protection comes with a spray. It feels a little weird to spray your phone with this solution but I found the application actually easier than with the usual "dry" protections.
Note that it will probably be scary ugly after the installation (microbubbles, haze...) but it gets better after a few hours (12 to 20 in my case) and perfect after a few days.
Honestly i wouldn't go generic, you get what you payed for. Trust me i've learned the hard way haha
Heldorn said:
Best shot I could get. It is almost invisible anyway.
View attachment 870526
About the installation, the protection comes with a spray. It feels a little weird to spray your phone with this solution but I found the application actually easier than with the usual "dry" protections.
Note that it will probably be scary ugly after the installation (microbubbles, haze...) but it gets better after a few hours (12 to 20 in my case) and perfect after a few days.
Click to expand...
Click to collapse
Fantastic. It is truly invisible and sits neatly edge to edge. I could only make it out from the hole given for the sensor. Good job and thanks a lot. I am ordering one now from eBay.
Heldorn said:
Best shot I could get. It is almost invisible anyway.
View attachment 870526
About the installation, the protection comes with a spray. It feels a little weird to spray your phone with this solution but I found the application actually easier than with the usual "dry" protections.
Note that it will probably be scary ugly after the installation (microbubbles, haze...) but it gets better after a few hours (12 to 20 in my case) and perfect after a few days.
Click to expand...
Click to collapse
Thanks Buddy for the screenshot, just ordered one from the U.S., the UK seems to have some cacky ones, currently I am using this one: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=360428462851
Not a full screen protector either and I paid more...-_-
I don't like screen protectors. Never use them.
Besides this phone has gorilla glass. I have not even managed to scratch my other previous phones without gorilla glass after months of use. I rather take the risk of getting a little scratch rather than take away the nice touch feel of the screen.
dannejanne said:
I don't like screen protectors. Never use them.
Besides this phone has gorilla glass. I have not even managed to scratch my other previous phones without gorilla glass after months of use. I rather take the risk of getting a little scratch rather than take away the nice touch feel of the screen.
Click to expand...
Click to collapse
I will second that!
dannejanne said:
I don't like screen protectors. Never use them.
Besides this phone has gorilla glass. I have not even managed to scratch my other previous phones without gorilla glass after months of use. I rather take the risk of getting a little scratch rather than take away the nice touch feel of the screen.
Click to expand...
Click to collapse
Then you must not have exposed it to sand. I have managed to scratch almost all the screens I have had on cell phones without a screen protector even if they were made out of gorilla glass. Sand is the enemy to every screen. Metal, like keys or knives, are softer that the glass but sand (or some particles of sand) are not.
I just bought some cheap chinese screen protector (dry application) and it looked horrible. Had it on for 5 minutes and then ripped it off. Have to find a good soft wet application protector now, hopefully before I manage to scratch that thing of beauty.
I've heard good reviews of the Skinomi ones, so I may go for one of those. Does anybody know if the full body (transparent) version has something to cover the super-scratch-prone chrome around the camera? If you know about any screen protector with that feature please let me know, otherwise I'll order the screen only version and use some (custom?) workaround for the chrome thing...
Thinking about getting this:
http://www.ebay.com/itm/NEW-Nokia-L...607711?pt=PDA_Accessories&hash=item4ab238341f
Anyone tried that one?
EDIT:
Just ordered it. Hope it's good.
arkedk said:
Thinking about getting this:
http://www.ebay.com/itm/NEW-Nokia-L...607711?pt=PDA_Accessories&hash=item4ab238341f
Anyone tried that one?
EDIT:
Just ordered it. Hope it's good.
Click to expand...
Click to collapse
I did order a couple for my Omnia a few weeks ago, but unluckily they came faulty, with pretty irregular cut borders and a nasty white drop of some kind of glue in the middle. They were totally unusable. I wanted to send them back for a replacement, but a couple days later I've lost my Omnia at a concert...oh well
:good: what you guys think of Tempered Glass Screen Protector ? any one use this kind of Tempered Glass Screen Protector ? I think it will instead the normal Screen protector in the near future. because it's good tocuh . Anti-Glare, Anti-Scratch, Anti-Fingerprint
L.LA said:
:good: what you guys think of Tempered Glass Screen Protector ? any one use this kind of Tempered Glass Screen Protector ? I think it will instead the normal Screen protector in the near future. because it's good tocuh . Anti-Glare, Anti-Scratch, Anti-Fingerprint
Click to expand...
Click to collapse
I am using one, a cheaper than the Spigen one. But it works great! Suprisingly good actually. Since I hate screen protectors cause I always get one dust particle underneath it.. It makes me take it off again. But with the tempered glass It fell exactly on place and without any dust underneath it..
Armazia said:
I am using one, a cheaper than the Spigen one. But it works great! Suprisingly good actually. Since I hate screen protectors cause I always get one dust particle underneath it.. It makes me take it off again. But with the tempered glass It fell exactly on place and without any dust underneath it..
Click to expand...
Click to collapse
Yes. I think so. the feeling just like not use any screen protector
Think there may already be a thread on this, and yes, they are awesome.
http://forum.xda-developers.com/showthread.php?t=2441894
Note 3 Tempered Glass Screen Guard
Sent from my SM-N9005 using Tapatalk
I'm using this one-
http://www.amazon.com/gp/product/B00GPAFP7W/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
I'm using a MIME USA Feather Glass protector and have had it on my device since late October and it's still flawless. I would have a hard time using a regular protector in the future after having a tempered glass one.
L.LA said:
:good: what you guys think of Tempered Glass Screen Protector ? any one use this kind of Tempered Glass Screen Protector ? I think it will instead the normal Screen protector in the near future. because it's good tocuh . Anti-Glare, Anti-Scratch, Anti-Fingerprint
Click to expand...
Click to collapse
I have the Spigen glass and i love it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
أرسلت من sm-n9005 الخاص بي باستخدام تاباتوك
Dude, look in Note 3 Accessories section, there is a multiple page post on this already. Try searching some it will save people from having to post again lol
Eric214 said:
Dude, look in Note 3 Accessories section, there is a multiple page post on this already. Try searching some it will save people from having to post again lol
Click to expand...
Click to collapse
the spigen is way overpriced. there are others as good like the Nillkin brand. It has rounded edges too.
xdm9mm said:
The Spigen is way overpriced, there are others just as good, like the Nillkin brand, it has rounded edges too.
Click to expand...
Click to collapse
I'll put one in for the Tech Armor, it also has rounded edges.
http://www.amazon.com/gp/product/B00GPAFP7W/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
im using glass-M tempered lass,it is okay i guess,works fine but kinda fingerprint magnet,lol
You can pick one up in the Verizon stores, I'm not sure of the hardness rating, I like the feel, it's rounded, does the job and looks good. It's about 25 bucks, can get them cheaper online but if you need one ASAP, pick one up in the verizon store, they'll install it as well so if they mess up have them do it again free of charge.
But out of all the reviews, the best one seems to be by iloome.
I use this one:
http://www.ebay.com/itm/Spigen-SGP-...l_Phone_Screen_Protectors&hash=item3a8fcfe74c
Great screen quality.
Svid said:
I use this one:
http://www.ebay.com/itm/Spigen-SGP-...l_Phone_Screen_Protectors&hash=item3a8fcfe74c
Great screen quality.
Click to expand...
Click to collapse
That one looks nice, I really like the MIME Feather Glass since it is only .15mm thick.
I'm using the Spiegen - the top of the line one.
It works great so far and fits the Spiegn Sim armour vieww case with no problem.
While I like a good deal too, I don't understand that we buy a VERY expensive Note 3 and then try and cut corners with the Glass and case.
I wish I could use one. On day one, I started with the Verizon tempered glass screen protector and I loved the feel of it, but over a few days time, the top right corner developed an odd sort of hazy "bubble" that wouldn't stay flattened out. I confirmed the screen protector wasn't touching the frame, so I figured it was just the "crappy" store brand screen protector. I decided to go ahead and get a MIME Ghost Glass to replace it, and over the next few days, the same story. Top right corner, bubble.
Upon closer inspection, my Note 3 has an (almost) imperceptible "bend" in the very top right corner of the screen. The only way I could tell was the way the light warps a tiny bit in the reflection of the glass in just that corner. The rigid nature of tempered glass coupled with this slight bend in the phone's glass causes the corner of the protector to lift ever so slightly off the screen, creating the ugly bubble.
The phone was bought new, has never been dropped, and is in perfect condition, it's simply a manufacturing "defect". So, it's back to the regular old screen protectors for me.
L.LA said:
:good: what you guys think of Tempered Glass Screen Protector ? any one use this kind of Tempered Glass Screen Protector ? I think it will instead the normal Screen protector in the near future. because it's good tocuh . Anti-Glare, Anti-Scratch, Anti-Fingerprint
Click to expand...
Click to collapse
Yes, I used Tempered Glass Screen Protector. It is very nice to use and protect your screen from any scratch or fall in a floor.
WishRyder said:
I wish I could use one. On day one, I started with the Verizon tempered glass screen protector and I loved the feel of it, but over a few days time, the top right corner developed an odd sort of hazy "bubble" that wouldn't stay flattened out. I confirmed the screen protector wasn't touching the frame, so I figured it was just the "crappy" store brand screen protector. I decided to go ahead and get a MIME Ghost Glass to replace it, and over the next few days, the same story. Top right corner, bubble.
Upon closer inspection, my Note 3 has an (almost) imperceptible "bend" in the very top right corner of the screen. The only way I could tell was the way the light warps a tiny bit in the reflection of the glass in just that corner. The rigid nature of tempered glass coupled with this slight bend in the phone's glass causes the corner of the protector to lift ever so slightly off the screen, creating the ugly bubble.
The phone was bought new, has never been dropped, and is in perfect condition, it's simply a manufacturing "defect". So, it's back to the regular old screen protectors for me.
Click to expand...
Click to collapse
I have MIME "Feather" on mine and don't have any problems.
Hi y`all.
Prefer brando rounded edge.
Removed it though. thought it botched up my proximity sensor.
Turns out it dosn´t work properly even with screen protector removed.
got a new sensor. Haven´t installed it yet. fairly simple though.
You guys have trouble with the proximity sensor?
Regards
ELO
So the Honor 5x is pretty damn tough:
https://www.youtube.com/watch?v=1Ud1zzi8VfY
At some point in the above video, guy decides to go from dropping it above his head, to 10th floor. I would guess that in between they had a hard time messing the phone up, and figured 10th floor should put a dent in it somewhere. Which is insane.
https://www.youtube.com/watch?v=OJ9-sTXPoek
The Aluminum case will scratch. LCD screen is tough.
https://www.youtube.com/watch?v=sKhQ3wdPBh4
https://www.youtube.com/watch?v=ePHsWx88GLY - fire cracker test
Mad props to the hardware folks at Huawei! So at this point the question is now: What case and or screen protector do you think is the best? Just a case? Just a screen/camera protector?
After watching those videos, I would say, you would want something on the back to protect the aluminum from being scratched (case), combo'd with a Tempered Glass Screen Protector.
Screen Protector :
Rely on this thread for the best one: http://forum.xda-developers.com/honor-5x/accessories/tempered-glass-screen-protectors-t3296240
My personal recommendation: The Honor 5x comes with a plastic screen protector by default. Its awesome that they include a screen protector by default. The default screen protector has a crappy feel to it, but it does work. I highly highly highly recommended you remove the default screen protector and purchase a tempered glass screen protector. I myself purchased a cheapo chinese Tempered glass screen protector. It feels like an iPhone after I upgraded. Meaning, the quality of the touch is super nice, its more responsive to the touch. I at first didn't believe people when they said this, but they are right. The cheapo screen protector didn't come with a cutout for the camera lens (which you can get).
Cases (for scratches):
NOT recommended:
Honor 5x flip cover case: https://store.hihonor.com/us/honor-5x-flipcover
The case that comes with the phone. Junk. No protection. I used this at the start, one time it fell off the table, the case actually came off the phone in mid air somehow, and the phone case-less landed on the concrete. Now I have a permanent mark.
Standard Clear Case - https://images-na.ssl-images-amazon.com/images/I/71-+PHk2giL._SL1500_.jpg
Clear cases from my experience, will eventually turn YELLOW. I currently have a clear case, it started out clear but turned Yellow/Brown.... ehh... If you have owned a clear case for a good period of time (maybe 6 months?).... Please specify if it yellows or not. You also have to make sure that on the front of the phone the lip of the case goes over the screen.
Recommended:
1. Thin case - The phone is tough, you just need to prevent scratches. Thin cases can make it easy to fit into pocket.
2. Front bumper - I wouldn't get a case if the lip didn't protrude from the front.
3. Stiffness - The case needs to be pretty stiff so the case doesn't move out of the way incase of an accident.
4. Distinct Physical Buttons - The phone without a case, its hard to figure out which is Volume+/Volume- and power by just using your finger. A case can solve this problem by adding bulk to each button. This alone is good enough reason to get a case.
Thoughts? Better recommendations?
I have this case very good not to bulky all round good protection only issue is it ships from China so had to wait awhile
http://pages.ebay.com/link/?nav=item.view&id=262152554826&alt=web
Sent from my KIW-L21 using XDA-Developers mobile app
---------- Post added at 05:57 AM ---------- Previous post was at 05:54 AM ----------
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my KIW-L21 using XDA-Developers mobile app
Yeah, I echo that - purchased the official case and it is a let down. Looks and feels cheap, which it most certainly is not!
Also, with any flip case, the fingerprint sensor is covered when it's open...
I've ordered the case that @tintin1892 recommended, but still awaiting delivery. Will see what that's like. I really don't want to be using the flip case, but I'm loath to chance the phone getting damaged so I'm continuing to until the shell arrives. Once it does, the flip case is gone!
The case I bought with my phone.. No issues, I think it looks great, has a little kick stand if you're into that and it's cheap! But the quality of the case feels like you're paying for something triple the price. Dropped the phone a couple times and not even a scratch on the case! I think it's in different colors too but I got the gray and black. https://www.amazon.com/dp/B0198BBURS/ref=cm_sw_r_other_apa_uVElxb0J06P91
I went with the Tudia case in the OP's first case link and have not been disappointed at all. Still using screen protector that came on the phone though.
Sent from my KIW-L24 using Tapatalk
I had a fantastic case called Trident Cyclops for my HAM2 (Thanks Super Bass).
So i ordered a case off Amazon but it doesn't have the plastic front frame like the Cyclops did, only a Cradle of sorts where you shove the Honor 5X in it and try to fit the rubber rim around the frame.
Is there any nice solid case still around like the Trident Cyclops was for HAM2 for the Honor 5X?
Nillkin Nature Clear TPU. My go to TPU brand/type for any of my phones. Not too bulky, with anti-slip on the sides, port protections and is as slim as it can be.
Sent from my KIW-L24 using Tapatalk
I have a Spigen transparent case, and it's very awesome ! It's leightweight, thin and very transparent.
You can see more here : https://www.amazon.fr/Spigen®-Crystal-Transparent-Adherence-Encombrement/dp/B01DJHHW74
Is there any OtterBox for the 5x?!
Nilkin plus Nilkin for me. :victory:
I've been using a Nilkin glass and Caseformers combo since Feb. I drop my phone all the time, on concrete, and hardwood floor. Only recently got a couple cracks in the screen protector and scuffs on the case. Best combo I've had for any device I've had.
Sent from my KIW-L24 using Tapatalk
tintin1892 said:
I have this case very good not to bulky all round good protection only issue is it ships from China so had to wait awhile
http://pages.ebay.com/link/?nav=item.view&id=262152554826&alt=web
Sent from my KIW-L21 using XDA-Developers mobile app
---------- Post added at 05:57 AM ---------- Previous post was at 05:54 AM ----------
Sent from my KIW-L21 using XDA-Developers mobile app
Click to expand...
Click to collapse
This case sucks. I brought it via ebay. There are two main issues with this.
The headphone jack opening was too small. My headphone jack does not completely plug in. Alternative is to use bluetooth headset.
The fingerprint opening was too small. It fails to unlock your phone 8 out of 10 times. Alternaitve: You will have to use PIN/Password/Pattern to unlock your phone aka fingerprint scanner is useless.
I switched to Huawei Honor 5X Case - TUDIA Full-Matte ARCH TPU Bumper Protective Case for Huawei Honor 5X. It's perfect. It did not have any of the above issues at all. Highly recommend. Wish they have Otterbox defender case for this phone or one with belt clip and secure.
Honestly, about the screen protector. Even a simple tempered glass protecter does the job well. But if you are really really looking for something great, look for Olephobic coated tempered glass for it.
AtaliaKetch said:
Honestly, about the screen protector. Even a simple tempered glass protecter does the job well. But if you are really really looking for something great, look for Olephobic coated tempered glass for it.
Click to expand...
Click to collapse
Well , am pretty sure u gave a great answer.
Usually devices get such coating on screen. Adding a second layer gives any colour glitches ? Just asking
gopinaidu77 said:
Well , am pretty sure u gave a great answer.
Usually devices get such coating on screen. Adding a second layer gives any colour glitches ? Just asking
Click to expand...
Click to collapse
I did not notice any colour differences at all. I have seen Olephobic coating on main glass only in high end devices. There are few reputable brands offering those kind of.
AtaliaKetch said:
I did not notice any colour differences at all. I have seen Olephobic coating on main glass only in high end devices. There are few reputable brands offering those kind of.
Click to expand...
Click to collapse
Yes my honor 8 have such
You could find an 'anti-glare' glass for it as well. It will help you a lot but might little bit make colors on your screen 'washed away'. I wish if I could find them in my country for cheap though.
Here is the link to anti glare glass: https://www.amazon.com/Mr-Shield-Anti-Glare-Protector-Replacement/dp/B016DDC582/ref=sr_1_1?ie=UTF8&qid=1501341053&sr=8-1&keywords=honor+5x+anti+glare
Spigen and Nillkin combo always works wonders for me.
simple tempered glass and silicon cover does the job for me.
Well not for me.
EDIT: Now that 5 months have gone by and some top contenders have truly emerged, I've updated the OP with the list of the protectors that seem to be the favorites in this thread and in others.
The purpose of this thread is to discuss screen protector options for the Pixel phone. This is where you can post thoughts and pictures of screen protectors you've purchased/used and to provide reviews and suggestions for others looking for tempered glass, plastic and wet apply screen protectors.
IntelliARMOR IntelliGLASS PRO
https://www.intelliarmor.com/shop-by-device/pixel/intelliglass-pro-pixel-black-screen-protector.html
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Pros:
- Full adhesive across the entire protector
- Full coverage
- Comes in black or white
Cons:
- Adhesive in center of screen is going to show dust particles more prominently.
- Edges may not adhere properly in some areas. (Blow dryer and pressure applied in the area for 1-2 minutes usually solves this)
Orzly 2.5D Pro-Fit Tempered Glass Screen Protector
https://www.amazon.com/Google-Prote...898800&sr=1-3&keywords=intelliglass+pro+pixel
Pros:
- Full coverage
- Comes in black or white
- Easy to apply perfectly
Cons:
- No adhesive in center of the screen which creates space between screen and protector
- Can give an almost mirror like reflection from certain angles in highly lit areas
- "Dot matrix" over the screen, making reading text difficult in direct sunlight
- Can make blacks on the screen look very washed out and gray
Spigen GLAS.t R Slim Tempered Glass Protector
https://www.amazon.com/dp/B01N8S5R93?th=1
Pros:
- Full coverage
- Comes in black or white
- Easy to apply perfectly
- No dot matrix in center of screen like Orzly
Cons:
- Can make blacks on the screen look slightly washed out (but not nearly as bad as the Orzly)
...
There are other options but these 3 seem to be the most favored among Pixel users.
I ordered the tempered glass from Verizon's website. With my discount it was like $16 and they usually work pretty well.
I got the Spigen Google Pixel Screen Protector Tempered Glass, I really like it.
Got this one: Spigen Google Pixel Screen Protector Tempered Glass / Full Coverage / 9H Hardness / Case Friendly for Google Pixel - Black
rumbikrobo said:
So many screen protectors, so little quality
Click to expand...
Click to collapse
Pleson and Orzly typically make some very solid TG protectors. However, I must admit that I'm pessimistic about the fit due to the curved edge of the screen. But at just $8 I'm willing to give it a try. Fingers crossed.
I have always been a fan of Invisible shields by Zagg. they haven't officially announced for Pixel yet though.
jed.padilla said:
I have always been a fan of Invisible shields by Zagg. they haven't officially announced for Pixel yet though.
Click to expand...
Click to collapse
BOOM!
https://www.verizonwireless.com/accessories/zagg-invisibleshield-glass-screen-protector-pixel/
I will never understand the desire to put this horrible ugly **** on your expensive phone, even worse than a case.
mdmogren said:
I will never understand the desire to put this horrible ugly **** on your expensive phone, even worse than a case.
Click to expand...
Click to collapse
A perfectly installed tempered glass protector looks and feels like it isn't even there. However, with the curved edge of the Pixel screen, I am doubtful that I will be able to accomplish a perfect install. Admittedly, after going through a few protectors with my OnePlus 3, I ended up saying "screw it" and went bare with the screen and felt liberated. :laugh:
The screen looks/feels so great without a protector that it's worth getting some micro-scratches. The main reason I try to use a screen protector is for resale value purposes. But this time around I really am hopping to keep the Pixel for the full 24 months instead of making an incremental upgrade after 12 months. By then the phone will be worth like $150 anyway. So this time around, if I can manage a perfect install with the Pleson TG protector, I'll keep it on. If it doesn't work I'm going to throw it in the trash and just enjoy the screen bare.
I purchased Google Protect anyway so if something happens to the screen I pay them $79 and get a brand new phone the next day. With protection like that it's actually gotten silly to drop upwards of $50 trying all sorts of screen protectors.
jhonwright56 said:
Try this anti bubble "skinomi" screen protector available at amazon http://amzn.to/2djc8aJ
Click to expand...
Click to collapse
I've used that screen protector on my OnePlus 3 and can't stand it. It has a rubbery feel to it and makes the screen look grainy. For me it's tempered glass or nothing.
I got the Pleson coming right now. I usually use the Skinomi glass protectors but they told me they were not ready as of yet. Pleson makes amazing cases wo i will try their screen protectors out. if they crack i will get skinomi later
I have a Pleson on my 6P and it's great.
I'm curious though, the first batch of 6P protectors covered the proximity sensor and people had issues. I'm assuming that thing under the top speaker (on the Pixel) is the proximity sensor and it appears to be covered. Maybe I'll wait for some reviews.
Sent from my Nexus 6P using Tapatalk
daewond3r said:
I have a Pleson on my 6P and it's great.
I'm curious though, the first batch of 6P protectors covered the proximity sensor and people had issues. I'm assuming that thing under the top speaker (on the Pixel) is the proximity sensor and it appears to be covered. Maybe I'll wait for some reviews.
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
They are cheap enough that I jumped in. 8 bucks for 2 of them... Why not
Sent from my Nexus 6P using Tapatalk
jerflash said:
They are cheap enough that I jumped in. 8 bucks for 2 of them... Why not
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
It's def a good deal. Not hating on anyone who's taking a chance on the first batch and I hope there's no issues. I'm just gonna wait to find out.
sn0warmy said:
Pleson and Orzly typically make some very solid TG protectors. However, I must admit that I'm pessimistic about the fit due to the curved edge of the screen. But at just $8 I'm willing to give it a try. Fingers crossed.
Click to expand...
Click to collapse
You can definitely go well with orzly, often a solid choice
lordred12345 said:
You can definitely go well with orzly, often a solid choice
Click to expand...
Click to collapse
I just hope the curved edge doesn't force the TG manufacturers to do what they did with the OnePlus 3, which was leave the adhesive on the sides and keep the middle of the protector just hovering over the screen because it created that obnoxious rainbowing in the middle of the screen and allowed dust to get in betweent he protector and the screen. .
bought the pleson TG 2 pack. I hope armor shield jumps into the game, love their stiff.
sn0warmy said:
I purchased Google Protect anyway so if something happens to the screen I pay them $79 and get a brand new phone the next day.
Click to expand...
Click to collapse
I have used Google Protect on my 5X and I assure you that your replacement will NOT be new(could be, but won't be). Change "brand new" to "refurbished" and you got it right. I tried three replacements for my 5X, all were refurbished. All had loose back covers and one had a pink screen. I ended up replacing the back cover myself with an aftermarket replacement to address the looseness.
shelleyldiaz said:
You can also go with iLLumiShield screen protector for Google Pixel.
Click to expand...
Click to collapse
^ Thanks for that link! It displays some good options for people to consider. I'm going to add this to the OP.
sn0warmy said:
I just hope the curved edge doesn't force the TG manufacturers to do what they did with the OnePlus 3, which was leave the adhesive on the sides and keep the middle of the protector just hovering over the screen because it created that obnoxious rainbowing in the middle of the screen and allowed dust to get in betweent he protector and the screen. .
Click to expand...
Click to collapse
Im confident that orzly will be okay as they did fix most of the issues with their second edition. It's what I use now
lordred12345 said:
Im confident that orzly will be okay as they did fix most of the issues with their second edition. It's what I use now
Click to expand...
Click to collapse
Yeah, I remember you and I discussing the Orzly protector for the OnePlus 3. My rev 2 was pretty solid and offered great protection with a clean look. But over a few weeks it started to let dust get in, which got annoying. The plus side to that protector is you can peal it off, clean the screen and re-apply.
However, a couple of weeks ago I decided to go with no protector on the OnePlus 3 and it just feels/looks too great to go back. Since ordering the Pixel I've been much less gentle with the OnePlus 3, as well. The screen has now been exposed to plenty of dirt/grime from using it while working on the car and even sand from our camping trip this last weekend. Yet, every time I clean it and inspect the screen under florescent lighting I can't find a single visible scratch.
And supposedly the OnePlus 3 screen is less scratch resistant than other current flagships. If that truly is the case, then I'm seriously thinking the screen protector days might be behind me. Unless I can manage a perfect install with the Pleson one I ordered, that is.
sn0warmy said:
Yeah, I remember you and I discussing the Orzly protector for the OnePlus 3. My rev 2 was pretty solid and offered great protection with a clean look. But over a few weeks it started to let dust get in, which got annoying. The plus side to that protector is you can peal it off, clean the screen and re-apply.
However, a couple of weeks ago I decided to go with no protector on the OnePlus 3 and it just feels/looks too great to go back. Since ordering the Pixel I've been much less gentle with the OnePlus 3, as well. The screen has now been exposed to plenty of dirt/grime from using it while working on the car and even sand from our camping trip this last weekend. Yet, every time I clean it and inspect the screen under florescent lighting I can't find a single visible scratch.
And supposedly the OnePlus 3 screen is less scratch resistant than other current flagships. If that truly is the case, then I'm seriously
thinking the screen protector days might be behind me. Unless I can manage a perfect install with the Pleson one I ordered, that is.
Click to expand...
Click to collapse
Ah yeah I remember your profile picture somewhat. I don't get that much dust buildup but mainly due to my case probably hiding it well!
Ideally we would all like no case or screen protector on our phones but life isn't like that ????
My OPO got quite scratched up unfortunately before I had a screen protector so I always need one now!
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
I bought this case by Nillkin for my phone and it came with a free screen protector film (not a glass protector) and I find it pretty decent. I didn't find any issues with fingerprints on it.
You can find it here: https://www.amazon.com/OnePlus-Nill...=1504853058&sr=8-3&keywords=oneplus+5+nillkin
The Nillkin TGSP is probably the most compatible at the moment but it does have the larger gap around the edges, I've still got mine applied, hoping for more luck with the Rhinoshield case and a full face protector as the case is supposed to be much more compatible with them, my advice would be to go for the Nillkin until we all find the perfect replacement.
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
dasti555 said:
http://www.dx.com/p/naxtop-tempered...for-oneplus-5-transparent-470989#.WbOz7iNnp74
Anyone tried this one?
Transparent or with black borders?
Click to expand...
Click to collapse
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
3DSammy said:
Thanks. Looks interesting particularly the all transparent version, curved edges and its cheap enough to experiment. There is no indication on where the adhesion is and no specific mention of a Oleophoic coating but describes an anti-fingerprint coating. I currently have the under screen dust issue with my Orzly tgsp but I love the feel of that screen so am looking for a alternative protector with similar finger feel.
I'm suspecting that my bumper case is causing the Orzly's issue as the dust only comes from the volume rocker area and likely due to the case pushing the Orzly's edge when pressed. Maybe this alternate protector with the curved edges would not have the same issue, while the all transparent version would likely have no issues cutting off the screen view unless the curved edge causes some undesirable optical effect.
If you get one please post your observations.
Click to expand...
Click to collapse
Well I post it here because I was looking if somebody already bought it. I have orzly with I'm happy however it have rainbow effect in the middle and sometimes it's quiete visible. My friend told me that he bought that one from link I sent (with black borders) and he is told me he don't have rainbow effect or cutted screen.. so i don't know
Like you I'm more interested in the transparent one as I don't know why there is even a black version on any of them.
On my Orzly I've seen the rainbow effect but only when the screen is at an unusual angle while wiping the surface clean but never when using the phone normally. It's only the dust that is driving me crazy. I'm even considering going with just my bumper case and no protector but I'll wait a while before going that route.
This one looks interesting (not glass though), quite clever application method, reminds me of the default screen protector that comes with the phone that a lot of people seem to like
Ringke Invisible Defender Screen Protector
https://www.amazon.com/Protector-Invisible-Guaranteed-Compatible-Clearness/dp/B074137YDH/
Just read the Amazon reviews and they're not that positive.
I still have to receive my oneplus 5. Would you guys recommend keeping the pre-applied film with the orzly bumper over any screenprotector that's on the market now?
ned4spd8874 said:
The title pretty much covers it. I see many questions on this, but no definitive answers. I tried the official one but returned it since it would cover the edges of the screen. Bought one off of Amazon that said it didn't do that, but it did as well.
So simply, I'm looking for one that won't cover the screen is good quality. Simple enough, no?
Click to expand...
Click to collapse
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
I bought the one from Nillkin until a better one came along. However it was pure garbage. It didn't fit the whole screen and the top notch was way off center. But the main reason I threw it in the trash was there was the entire right side would not stick to my phone. There was a good 1/8" section all along the right edge that was not sticking and just looked like crap.
Finally the almost perfect tgsp.....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
spawn549 said:
Finally the almost perfect tgsp.....
Almost perfect is because its not fully adhesive. Only perimeter adhesive.
so dust will appear along the sides and rainbow will appear sooner or later.
Click to expand...
Click to collapse
Which one is it
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
srt99 said:
i am in the same boat as you.
found this -
imak Oneplus 5 Transparent Clear Full Cover Edges 0.15mm TPU LCD Screen Protector for Oneplus 5 back Anti-shock Protective Film
http://s.aliexpress.com/BBBjERbi
(from AliExpress Android)
i just want clear protective glass that covers the whole screen. anything similar to whitestone dome protective glass (for s8) would be great.
Click to expand...
Click to collapse
I just picked up two packs for fun - will report back.
spawn549 said:
i dont recommend it. after few hours of usage tiny dust appearing from speaker and sensor holes going right inside the tgsp. the coating is bad. attracts fingerprint n dust. screen will smudge all over.
Click to expand...
Click to collapse
Got it, but wich brand produce this one? Just to look around
No brand packaging on it...i would stay away from non full adhesive due to it attracts dust and rainbow effect. I would rather use a full adhesive tgsp eventhough it will block few mm from the sides
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
bibi98 said:
This is the best I found for now. Not full covered but minimal bars on the side and almost no rainbow effect. After 2 weeks no dust at all.
https://fr.aliexpress.com/item/Scre...lus-3-3T-Three-1-3-1-3T-Full/32795224827.html
Click to expand...
Click to collapse
Do you also use a case with this protector? If you do please indicate which one as even an all adhesive tgsp can be lifted by many of the cases being sold.
Disgustip8ed said:
I just picked up two packs for fun - will report back.
Click to expand...
Click to collapse
Anything new about those glass screen protectors?