Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
flagpol said:
Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
Click to expand...
Click to collapse
Do you find the solution yet? Cause I face the same problem too..
Tzul please help.. :crying:
me too, please help
similar issue, cant power on, keep on vibrate loop interval, no display, not detected by pc
flagpol said:
Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
Click to expand...
Click to collapse
Hi, did you find anything?
I have three TB3-710l (they are the company I work for), I have successfully root 2 of them but the newest tablet doesn't have the same luck.
First I install TWRP by Tzul, but the TWRP have an error never mount anything.
Second I try to flash stock firmware (Lenovo_Tab_3_TB3-710I_MT6580_S000032_160921) then the same happened, never turn on and just vibrates.
Always using SPFT, and now I have the same problem has you: always shows that it cannot load DRAM (4032 error or 0xFC0 error).
EDIT: Hi, for everyone who get in here with this problem, please read all this thread.
I unbrick my tablet with this answer in specific.
Good Luck!
asdrubalsantander said:
Hi, did you find anything?
I have three TB3-710l (they are the company I work for), I have successfully root 2 of them but the newest tablet doesn't have the same luck.
First I install TWRP by Tzul, but the TWRP have an error never mount anything.
Second I try to flash stock firmware (Lenovo_Tab_3_TB3-710I_MT6580_S000032_160921) then the same happened, never turn on and just vibrates.
Always using SPFT, and now I have the same problem has you: always shows that it cannot load DRAM (4032 error or 0xFC0 error).
EDIT: Hi, for everyone who get in here with this problem, please read all this thread.
I unbrick my tablet with this answer in specific.
Good Luck!
Click to expand...
Click to collapse
THis might WOrk i ve havent tried yet ,tho i wanna flash it now
https://forum.xda-developers.com/android/development/tb3-710i-tb3-710f-rom-stock-rom-lenovo-t3437810
same problem faced,can any developer please help us
Related
Hello guys! I am very new here. I hope you can help me by any chance. As stated on the title itself I got a Lenovo ideapad K1 getting error such Unrecoverable Bootloader Error (0x0000004). This how it happens before I get the error.
I was currently running Kaschemme's custom rom for lenovo k1, CM10.1(android 4.2.2). I have this tablet where the physical home key is faulty I have read from some Lenovo k1 thread how to fix it. Then tried the method then it worked. The next morning, I used the K1 and its a bit acting up and started lagging then hang's up. I do a force shutdown then tried the method again to make the home key work while booting up until it reaches the homescreen then instatntly hung up. This happened 3x and I used the same previous method every time a boot up the tablet. For that 3rd time it never reached the homescreen I had a series of hanging at the Cyanogen boot animation and did a force shutdown and never tried using the method to make the home key work. After these series of hanging and force shutdown at the bootanimation, now it only boots up until the Lenovo logo and never passed that logo. After that I decided to reinstall Kaschemme's CM10.1 for lenovo k1 by entering to APX mode then when installing and everything was successful waited for my tablet to reboot but NO REBOOT happened, but instead I got the aforementioned error. I even tried to reinstall that same ROM and even, AOSP JB by Khanning, HC stock, HC rooted rom for Lenovo K1 and no luck at all.
Untill now I can't figure out what had just happened and how and why I got that silly error. Hope you guys, Lenovo k1 users especially , can help me specially to Kaschemme who did very good job in supporting the lenovo K1 users.
THANKS in advance
Just in case in the future I might be able to solve this or somebody out there will be kind to help with my problem with my Lenovo k1
Just tonight, I tried to install the ROM CM10.1 by Kashchemme as soon as it reached the last .img to fully installed and before the device should reboot I tried to force shutdown before I see the ERROR message again. When I turned it on it immediatly went to APX mode without pressing the 2 volume buttons together with the power button. I tried to force shutdown it for 3 times and it always went to APX mode. Tried to install Rooted HC by Khanning, it reaches the last .img (userdata.img) to be installed successfully but still no luck and I got the additional information
failed executing command 25 NvError 0x120002
command failure: sync failed <bad data>
bootloader status: Bct Write Failed <code: 22> message: nverror:0x42004 <0x42004
> flags: 0
Pleae help what do these things mean and how can I recover my tablet. Is Jtag possible? how to JTAG this lenovo k1? please anybody share your knowledge. Thanks
My LENOVO K1 is finally alive and working after so many attempts
Just an update
Right after my recent post tried to reboot my tablet. It boots up. The Lenovo Logo showed again and it proceeds and showed the NVIDIA logo then after that another Lenovo logo until it reaches the homescreen. Finally my tablet is FInally ALIVE so happy that I saved my old ROM's which brought my tablet back to life.
Now I don't know if I am running the rooted one or not because I don't see the SUPERUSER app on this HC rooted by Khanning.
If anyone of you might have the same problem with your LENOVO K1 try the way I did. Just read my previous posts. If you have any question that I might able to help jut let me know.
LONG LIVE ANDROID!!!!!
I am having the same issue, while trying to flash Kaschemme's CM10.1 i got the "unrecoverable bootloader error (0x00000004). could you tell me where you got the version of HC that you were able to get running?
trackid said:
I am having the same issue, while trying to flash Kaschemme's CM10.1 i got the "unrecoverable bootloader error (0x00000004). could you tell me where you got the version of HC that you were able to get running?
Click to expand...
Click to collapse
Look for the thread created by Kastella. Another K1 user. I post the link there. Sorry I can't post the link now just using my phone to reply. Hope you understand
Sent from my MT27i using XDA Premium HD app
trackid said:
I am having the same issue, while trying to flash Kaschemme's CM10.1 i got the "unrecoverable bootloader error (0x00000004). could you tell me where you got the version of HC that you were able to get running?
Click to expand...
Click to collapse
Here is the link to that thread
http://forum.xda-developers.com/showthread.php?t=2575775
Sent from my MT27i using XDA Premium HD app
Btw, which ROM where you using before you attempted to flash CM10,1?
Sent from my MT27i using XDA Premium HD app
Thanks, I cant remember exactly which one it was since i flashed it over a year ago, but it was a jellybean Rom made by Khanning.
How to solve the issue?
johnwilliam_a_k_a_trash said:
Hello guys! I am very new here. I hope you can help me by any chance. As stated on the title itself I got a Lenovo ideapad K1 getting error such Unrecoverable Bootloader Error (0x0000004). This how it happens before I get the error.
I was currently running Kaschemme's custom rom for lenovo k1, CM10.1(android 4.2.2). I have this tablet where the physical home key is faulty I have read from some Lenovo k1 thread how to fix it. Then tried the method then it worked. The next morning, I used the K1 and its a bit acting up and started lagging then hang's up. I do a force shutdown then tried the method again to make the home key work while booting up until it reaches the homescreen then instatntly hung up. This happened 3x and I used the same previous method every time a boot up the tablet. For that 3rd time it never reached the homescreen I had a series of hanging at the Cyanogen boot animation and did a force shutdown and never tried using the method to make the home key work. After these series of hanging and force shutdown at the bootanimation, now it only boots up until the Lenovo logo and never passed that logo. After that I decided to reinstall Kaschemme's CM10.1 for lenovo k1 by entering to APX mode then when installing and everything was successful waited for my tablet to reboot but NO REBOOT happened, but instead I got the aforementioned error. I even tried to reinstall that same ROM and even, AOSP JB by Khanning, HC stock, HC rooted rom for Lenovo K1 and no luck at all.
Untill now I can't figure out what had just happened and how and why I got that silly error. Hope you guys, Lenovo k1 users especially , can help me specially to Kaschemme who did very good job in supporting the lenovo K1 users.
THANKS in advance
Click to expand...
Click to collapse
Hi,
I have faced the same problem of Unrecoverable Bootloader Error (0x0000004) with exactly the same situation. However I can't find your way to solve the issue. Could you please teach me the way of solution?
Thanks!
seananyoung said:
Hi,
I have faced the same problem of Unrecoverable Bootloader Error (0x0000004) with exactly the same situation. However I can't find your way to solve the issue. Could you please teach me the way of solution?
Thanks!
Click to expand...
Click to collapse
I think it was just a storke of luck. Because right now after several times of attempt I upgrade my K1 to Kaschemme's Rom my K1 always get bricked. I did it for about 7 times of reviving back to HC. Now my tablet is totally useless. I even tried to do the bake technique but still having error I might try it as well on Sunday. Just keep on pushing the HC and you will able to revive it soon. Good luck.
Sent from my GT-I9500 using XDA Premium HD app
Greetings there fellow xda members...
Yesterday a friend of mine gave me her Lenovo s820 (MT6589) to change her ROM.
It came rooted so I just downloaded from play store 'Mobileuncle MTK tools' and selected update recovery.
I flashed it and then rebooted. The recovery was in Chinese so I rebooted again and searched for an english copy of cwm.
I found a guide here about how to flash a custom ROM on this device and downloaded 'CWM_v6.0.3.4_S820_ROW' that was provided.
I flashed the .img file using mobileuncle but after I pressed reboot the phone wouldn't turn on. Not a boot loop, just nothing.
After a couple of hours searching and trying different solutions the phone powered on and I have no idea how I did it.
Now sometimes it boots, sometimes it doesn't.
Most of the times it boots it's after running memory test using the 'SP Flash Tool v5.1352.01' but I don't thing they are somehow related.
Also, Flash tool displays the following error in memory test "ERROR: NAND Flash was not detected!"
but I had no luck finding a solution for that either or if it is somehow related with the problem since most of the people facing that error had formatted NAND something I didn't.
Thanks for reading, I hope someone can help me fix it otherwise I'm in some serious trouble :fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
Never Mind... fixed it... I downloaded the official lenovo and everything works now.. thanks for reading...
Hi I have an Allwinner A10 clone (Kurio 7), it is designed for kids but otherwise a standard android tablet.
After hours of googling I rooted and installed CWM & Gapps (not included in the stock ROM). So far so good.
The stock ROM was causing issues with some apps, it needed to go.
I flashed CM10 and it worked but no touch screen. It needed a compatibility flash to make it work. You can guess what's coming. I picked the wrong one and now the device does the following:
Reboot loop
Black screen (backlight though)
PWR+Vol up no longer gets to recovery
Vibrates constantly between reboots (due to wrong patch I'm guessing)
ADB picks up the device for a split second between reboots but "adb reboot recovery" does nothing. Even when using wait command.
Tried "fastboot flash recovery cwm.img" after wait command, no luck.
Is there anything else I can try?
I fixed this.
I used the GoClever TAB A73 ROM and instructions in their support/update/download area.
Sorry I cannot post links as I am still a newbie.
Anyway flashing using Livesuit this fixed the problem.
Turzyx said:
I fixed this.
I used the GoClever TAB A73 ROM and instructions in their support/update/download area.
Sorry I cannot post links as I am still a newbie.
Anyway flashing using Livesuit this fixed the problem.
Click to expand...
Click to collapse
Hi, can you please share with me how you manage to unbrick your Kurio 7. I had just bricked mine trying to install CM10.
Thanks.
lamkc said:
Hi, can you please share with me how you manage to unbrick your Kurio 7. I had just bricked mine trying to install CM10.
Thanks.
Click to expand...
Click to collapse
I guess this is the site he is refering to:
http://www.goclever.com/uk/support,c3/software-update,a28.html?aic=5&aia=185&ail=10
The LiveSuit pack is there for download, as well as the roms.
But there are three different 4.0 roms to choose from, and also a couple of 2.3 roms. I dont know which one he did use.
Since your Kurio 7 is bricked anyway, I guess you can try one by one and see if any of them work.
Please tell which one, if you succeed.
Hello guys,
this is my first post here!
I recently got Idol 2 from my brother to use and seeing as it says on GSM arena that it has KitKat I wanted to flash it to get rid of slow 4.2.2.
I used SP flashtool and on youtube I found how and also the ROM. I flashed it, first I used format all except bootloader and after flashing it wont switch on.
PC can see it and I tried every guide, I have 6 roms, many of them russian and every time I try flashing I get
brom error sft enable dram failed 4032. I somehow solved that but not I get brom error s_ft_enable_dram_fail (0xfc0) every time I try flashing.
I have a boat load of drives, I used USBDEVIEW to uninstall them and I have reinstalled them 47 times, always same error. Flashing wont start.
What am I doing wrong? IS there anyone who knows? :crying:
I really wanna fix it because I dont have a phone anymore..... I had to sell my OnePlus 3 cause of money issues and cannot afford a new one.....
Thanks in advance!
So I tried to flash TWRP with Flashr on my J3, but when I booted into recovery a blue screen came up saying that system software not authorized by AT&T was found on your device. I got nervous and decided to flash a stock firmware on to my J3, but it fails every time. I finally got to like 10% but then it failed and a blue screen saying,"An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software." Smart Switch crashes every time I put in my serial number though so now I'm stuck with a bricked phone. Any help would be greatly appreciated :fingers-crossed:
lolcoder124 said:
So I tried to flash TWRP with Flashr on my J3, but when I booted into recovery a blue screen came up saying that system software not authorized by AT&T was found on your device. I got nervous and decided to flash a stock firmware on to my J3, but it fails every time. I finally got to like 10% but then it failed and a blue screen saying,"An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software." Smart Switch crashes every time I put in my serial number though so now I'm stuck with a bricked phone. Any help would be greatly appreciated :fingers-crossed:
Click to expand...
Click to collapse
Try flashing again with Odin, but this time use older versions, maybe v3.10.6 or v3.09.
Solution
I flashed a random root file that I found on another xda post and it managed to boot.
lolcoder124 said:
I flashed a random root file that I found on another xda post and it managed to boot.
Click to expand...
Click to collapse
Next time, try not to flash files blindly, because any file that is wrong can brick your phone.