Related
Hello,
I've got my TyTN in europe (ROM 1.18.256.104) and my "usb" car charger is not working (charge sometime but ONLY if my TyTn is switched off....not usefull for GPS...)
I've tried another one same problem...restested with my 9100 : ok .
Is it due to the charging load ???
Anyone experiencing the same problem ???
Cheers
André
If I remember correctly the 9100 used an 800mA charger and the TyTn uses a 1A charger. That could be your problem.
hello,
same problem, but charging work on laptop (normally laptop is unable to offer more than 500ma).
I've read an article with C500 where charging work when pin 4 of the usb cable was linked with gnd. Is the same problem with Tytn ?
cheers
Tom
yep, had the same problem too with a standard charger with usb cable.
the charger output was 500mA. it stopped charging after a few seconds.
Recently i bought a Brodit carholder with the charger included. This charger has 1000mA output and its charging without problems.
So you need at least a 1000mA(1A) charger, otherwise it will not work well.
yep, had the same problem too with a standard charger with usb cable.
the charger output was 500mA. it stopped charging after a few seconds.
Recently i bought a Brodit carholder with the charger included. This charger has 1000mA output and its charging without problems.
So you need at least a 1000mA(1A) charger, otherwise it will not work well.
Thanks Luminus for the Reply, But are you sure there is no electronic part added on this car charger ? :?
Strange enough, both my car charger and USB Mains adapter (1A output) (which I was using for O2 Mini and Dopod 818Pro without any problem) was charging fine on my Dopod 838Pro, but the unit had a problem and I was given a new unit. This unit now does not work with my car charger nor the USB Mains adapter.
Looks like a trip down to the service centre again!
it was a cigarettelighterplug adaper with a usb output, with a regular usb/miniusb cable. the adapter was 500mA.( input 12V/output/5V)
it was a complete kit. you could use it for anything you want.
I only attached the TyTN to this adapter.
the adapter couldn't hold it, the amps exceeded the 500mA and stopped loading. the adapter still works on other devices.
the brodit has the same type of adapter, only with a fixed cable on it and 1000mA. this works perfect.
thats why i think that you need a 1000mA one to get it charging.
Hello,
Perhaps true perhaps not...
I used an official Qtek charger -> 1A ..it work
But not sure that due to the 1A because tried to use a self powered USB Hub and it work too ... I will check the official Qtek car charger (if nothing specific)
I use several chargers. i notice that sometimes, if a charger will only charge the device when switched off, i soft reset the device and then it will charge when on. strange problem. the problem of not charging when on, also occurs with chargers that for sure have over 1 amp.
Same problem here......tried to use the mini usb charger I got with my Leadtek BT GPS mouse......
Sometimes it will charge.....sometimes not....
Problem seems to occur when I switch the device on....ie receiving a phonecall or a textmessage....
It then stops charging only to resume after the phone goes back into stby mode....
Weird.....
Danny.
I have the same problem. I have HTC TyTN and 1A car lighter charger with normal USB cable.
Charging from normal, regular charger works. Charging from computer's USB works. Charging from car adapter works only sometimes.
I've tested about ten different car chargers, including one 2A - still nothing.
I've done factory reset of TyTN - after reset it was working for two days.
I have installed only few essential for me programs and no tweaks.
Cable is tested and working.
It makes no difference if I connect device turned on or off. It makes no difference if I reset device connected.
I have no more ideas...
I kept having the same problem but I think I've solved it.
I went into a T-Mobile shop and bought the 'official' car charger for T-Mobile SDA/MDA and I haven't had the problem since.
I've no idea what it's current rating is, because it has no relevant markings on, but it does get pretty warm in use!
help
I am really confused.
I have the sync wire that came with my device. It has stopped working as a charger from the laptop and I can;t active sync. I can however, de-activate the usb link and use the cable to activate my phone as a modem for the pc, so in theory it works at some level.
I also have another lead which is a compact one and it is giving me the same problem.
Both worked until this week so it isn't a case of them not being compatable.
Any ideas. I depserately need to sync. I can charge from the plug so thats no problem.
ahh
I have repaired actve sync and it seems to be ok now. I have no idea what happened.
Hi,
I'm getting some problems charging my Hero. As of last night, it's stopped taking any charge when connected to the mains (with the supplied USB cable and 3pin plug usb adaptors).... although when I connect it to my laptop, it seems to charge?!
It worked with both without issue until last night... although I do typically charge it at work via usb (except weekend, hence why I only noticed it last night).
Has anyone experienced a similar issue and know of any way to fix this?
Thanks,
Brian.
I've also tried both charging methods while the fone is switched off.... and it behaves the same way.
:-(
have you tried another charger? maybe an older style HTC MiniUSB charger (if you have one), cos it sounds like your charger's died.
Did you use the same cable for both methods (the supplied one with mains adaptor) if you did and it worked via pc/laptop then you would guess the mains adaptor has died.
I would say that your charger is dead. Power supplies on them blow sometimes, maybe from power surges, maybe they're just made poorly.
Try another charger.
Try unclipping and reclipping the pin plate. The interchangeable pins sometimes come loose.
So, bought the following cradle from DayDeal's ebay store:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=350284094212
The product description says the following:
* Custom-fitted Docking Cradle
* USB connection/charging cable
* AC power adapter
* Stylus
Now the issue is with the second line. What is NOT explained here is that the unit when plugged IN to a wall jack AND the sync charge cable is plugged in to your computer, the sync/charge cable gets no more power from the wall jack and wants to get it from ONLY the sync/charge USB cable. All of this leads to the unit being grossly undercharged and therefore, complains that there is not enough charge coming from the power source and that you need to shut down and therefore the whole idea of a wall charger is useless after this.
WHY would a sync/charge USB cable which by the way is physically attached to the unit and cannot be removed, while the wall jack plugs into a proprietary mini-USB cable. I know it's proprietary because I tried first to use the wall charging cable that came with my TP2 from Sprint.
So, I'd recommend not buying this cradle unless you want to do what I'm doing now, have a USB sync/charge cable dangling from the unit and NOT plugged into the computer, but instead only plug in the wall charger and sync and data transfer via USB which is what I was doing before except now, I have a cradle to do it in.
Not a good trade-off to me. I bought this specifically to be able to sync/charge FROM the cradle.
One last thing, don't think about using the cradle if you have a skin or a hard case on the phone. The connector is so flush with the back of the charging stand that if you try to put anything BUT the phone into the stand it can't connect.
EDIT: December 5, 2009:
Been in touch with the vendor. They are going to swap out this unit for another one. They say that the unit doesn't do this at their site and that this one may be defective. I'll gladly swap this one out for one that works as unstated or at least expected. I'll post when I've gotten the new unit if this is actually a defective first unit or if this is the actual way these units work. And, I'll also try this on multiple machines so that I know it's not just my home desktop.
Another bad cradle from ebay DELUXE CRADLE W/2nd Battery Slot FOR HTC TOUCH PRO 2
When AC plugged in and USB to PC the PC USB sucks the power so the phone charges slow or not at all. Also doenst seem safe for the USB to send the power back out to the PC from the cheapo AC plug in this cradle. When used as a standalone charger AC only it sometimes fails to charge, about a 50-50 success rate. Stay away from it.
That's good info. It is the exact cradle I bought, but i bought it just for charging. I have not used it for connecting to the PC yet, but i needed a cradle that had a slot for a battery in it too.
wpbear said:
Another bad cradle from ebay DELUXE CRADLE W/2nd Battery Slot FOR HTC TOUCH PRO 2
When AC plugged in and USB to PC the PC USB sucks the power so the phone charges slow or not at all. Also doenst seem safe for the USB to send the power back out to the PC from the cheapo AC plug in this cradle. When used as a standalone charger AC only it sometimes fails to charge, about a 50-50 success rate. Stay away from it.
Click to expand...
Click to collapse
That the one I have as well. I also have not use it for my computer.. All I really wanted was a cradle for my nightstand that had an additional battery charging slot as I also bought some of those $10 200mah batteries to try (have not received them yet)
dahauss said:
That the one I have as well. I also have not use it for my computer.. All I really wanted was a cradle for my nightstand that had an additional battery charging slot as I also bought some of those $10 200mah batteries to try (have not received them yet)
Click to expand...
Click to collapse
200mA or 2000mA? Got a link please? Sorry for off topic.
jonrobertd said:
200mA or 2000mA? Got a link please? Sorry for off topic.
Click to expand...
Click to collapse
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=390130739877
2000mah
I purchased this cradle and my complaint has to do with the USB cable that is attached to cradle. I need a long line to reach back of my PC. This attached one does not reach unless I want to view the phone from 5' away! Very disappointed. I've only had it a few days but didn't know this, sanjsrik:
What is NOT explained here is that the unit when plugged IN to a wall jack AND the sync charge cable is plugged in to your computer, the sync/charge cable gets no more power from the wall jack and wants to get it from ONLY the sync/charge USB cable."
Click to expand...
Click to collapse
It does seem slow to charge but I'll run a couple of tests to confirm.
Hi everyone, hope someone can advise.
I have a UK TG01 and it works ok but overnight it wont charge from the mains charger but it charges via usb.
I have tried different chargers and an old HTC mini usb charger with a mini to micro adapter fitted but its still the same.
I have the Mugen 1300Mha battery but its the same with the standard battery on all chargers.
I have cleaned out both the charger plug and the socket on my TG01 just in case of dust but no good it only charges via usb.
I have hard reset and flashed the standard UK Orange rom but this makes no difference.
Does anyone know whats going on? it was fine, no changes or software loaded and one day its fine and the next day it wont charge??
Any advice would be gratefully received, thanks for reading.
Faulty USB sockets i think try send it back to Toshiba for warranty repair.
Not sure about that as my TG01 does charge if I plug it into my laptop, this would suggest the socket is ok?
I believe that the charger is faulty, try a new micro usb charger, or try another socket
wafeeq said:
I believe that the charger is faulty, try a new micro usb charger, or try another socket
Click to expand...
Click to collapse
Agreed. As the TG01 is charging via USB, then there is most unlikely to be an issue with the uUSB socket on the phone.
To tell the TG01 to go into charging mode, the uUSB connector on the charger must have the two data pins shorted out. This is the equivalent effect to connecting to a host laptop or PC when connected via a USB sync and charge cable.
If you have a non-standard charger or are using an adapter from eg. mini-USB to uUSB it is very likely that this will not be implemented.
A few questions...
- Are you trying with the supplied Toshiba charger ?
- If so did it work OK with this before but not now ? [likely duff charger]
- If a 3rd part charger, again has it ever worked ? [if not then probably missing the required pin config]
Hope that is of some help.
Hi Kevin, its a genuine Toshiba charger and I have been using it since day one.
I took my charger into work today and tried a friends Nokia micro usb charger and that worked first time so duff charger.
No, I asked him to try my Toshiba charger and that also worked
So I assume my original charger possibly may not be 'shorting' correctly or presenting exactly the right resistance to the TG01 or possibly my TG01 is getting a little fussy about how it charges.
Anyway I have ordered a genuine Nokia charger from ebay and fingers crossed all should be well and thanks for all the advice everyone.
Hello,
my Prime does not charge at the moment. Neither in the dock nor with the charging cable.
I can connect it to the computer, i also charges there, but very slowly.
I just unlocked the prime and flashed AndroWook ROM.
What can I do?
Do you have another charger box? - It seems that your USB cable is good but possibly that the box that cable plugs into is bad or somehow defective, see if you can either A: Borrow someones charger box or if possible buy another one and test it to see if it works. IF it does work keep the charger or return it and possible contact whoever you bought your prime from and ask for a new charger.
It's most likely the charger box because the same thing happened to me. I am currently using my old cellphones usb charger. It doesn't show it as charging because it's like 5-10 volts instead of 15, but it still charges, just takes longer.