Bricked my OTT MXQ PRO 4K S905X - Android Stick & Console AMLogic based Computers

Hello, I recently tried to install custom ROM to my mxq pro, but probably I downloaded wrong rom and I bricked my tv box. It only freezed on startup screen "S905X" and then didnt go from there. After that, I tried to install firmware with USB burning tool method over computer, I downloaded firmware, and did everything as I supposed to do, but I always got error message on 3-4% "–[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error" .. after that, I tried to turn on my mxq pro but now it doesnt even want to turn on, all I get is red led indicator, and nothing more, PC recognize mxq but its always with that red led indicator, what should I do? Does anyone have same problem? Or does anyone have some firmware that should work with my mxq?
my chip is RTL8188 Realtek

same ****
skols155 said:
Hello, I recently tried to install custom ROM to my mxq pro, but probably I downloaded wrong rom and I bricked my tv box. It only freezed on startup screen "S905X" and then didnt go from there. After that, I tried to install firmware with USB burning tool method over computer, I downloaded firmware, and did everything as I supposed to do, but I always got error message on 3-4% "–[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error" .. after that, I tried to turn on my mxq pro but now it doesnt even want to turn on, all I get is red led indicator, and nothing more, PC recognize mxq but its always with that red led indicator, what should I do? Does anyone have same problem? Or does anyone have some firmware that should work with my mxq?
my chip is RTL8188 Realtek
Click to expand...
Click to collapse
some problem

Related

Cubot x9 not powering on or showing signs of activity!

Hello! So a while ago I bought a Cubot x9 and it was a really good phone. Recently i haven't been able to do anything with it due too I tried to root it and it bugged out so I reinstalled the rom on it and it fixed it for a while but now it won't even show that it's powering on or even charging. I tried connecting it too my pc to see if i could use odin too reset it but it's not displaying on any of the com ports. I'm curious if theres anything i can do for it. I have a newer and better phone now so i dont really need it but it would be nice to try to fix it or(In the case of my tablet) Fully modify it so nothing on it is stock on it.
Cloak2131 said:
Hello! So a while ago I bought a Cubot x9 and it was a really good phone. Recently i haven't been able to do anything with it due too I tried to root it and it bugged out so I reinstalled the rom on it and it fixed it for a while but now it won't even show that it's powering on or even charging. I tried connecting it too my pc to see if i could use odin too reset it but it's not displaying on any of the com ports. I'm curious if theres anything i can do for it. I have a newer and better phone now so i dont really need it but it would be nice to try to fix it or(In the case of my tablet) Fully modify it so nothing on it is stock on it.
Click to expand...
Click to collapse
For your information, odin is for Samsung devices only, hence why it wont recognize you because you are not in download mode. If adb or fastboot recognizes it you can manually flash stock ROM, that is, if you have adb. And also, does your phones display turn on or not?

T95Z 3/32 AP6255 USB Burn Tool 2% Error, SD Card Error

Hello all. The problem concerns Sunvell T95Z 3/32 wifi AP6255. I bought this device from Android 7.1.2. It worked well but I wanted more. I updated to POISON from this thread https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720 It worked better but I wanted to try other ROM using USB Burn Tool but each of them stops at 2% with error [0x10105002] Romcode / Initialize DDR / Read Initialize Status / USB Control setup error . despite this error, I still used POISON installed. I created the SD card using Burn_Card_Maker and it killed my device. it is recognized in the Device Manager and connects to the USB Burn Tool but stops at 2% with an error. Charging from the card does not work. I tried probably all existing ROMs and different versions of the USB Burn Tool program, but to no avail.
I noticed a lot of people with this problem. HEEEEEEEEEEELP!!!!
Problem solved. Thanks to @ khn993 from this forum http://freaktab.com/forum/main-category/main-forum/637675-nand-chip-mask-rom-mode-short-location
firmware request
KrisObcy said:
Hello all. The problem concerns Sunvell T95Z 3/32 wifi AP6255. I bought this device from Android 7.1.2. It worked well but I wanted more. I updated to POISON from this thread https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720 It worked better but I wanted to try other ROM using USB Burn Tool but each of them stops at 2% with error [0x10105002] Romcode / Initialize DDR / Read Initialize Status / USB Control setup error . despite this error, I still used POISON installed. I created the SD card using Burn_Card_Maker and it killed my device. it is recognized in the Device Manager and connects to the USB Burn Tool but stops at 2% with an error. Charging from the card does not work. I tried probably all existing ROMs and different versions of the USB Burn Tool program, but to no avail.
I noticed a lot of people with this problem. HEEEEEEEEEEELP!!!!
Click to expand...
Click to collapse
dear KrisObcy,
have you got any solution?
the firmware link is not working. have u got a firmware for 2/16gb t95z plus? i will be very greateful to you if you share firmware with me please
regards

H96 Pro Plus v3.0 ZH01 Bricked and can't use burn card. USB burning tool stops at 7%

I have a H96 Pro Plus 3G32G ZH01-S912TVBOX-V3.0 with a green board and 7.1 firmware.
I suddenly stopped turning on, so after some research I found a solution of replacing the capacitor to 1000mf at the DC jack. Now it turns on but, wont boot. TWRP recovery was loading to splash screen but blacked out after that. I tried using the USB burning tool to flash the firmware, but it gets stuck on 7%. The SD card method also stopped at the same place and the device just powers off.
After trying a number of times with a few different firmwares, the SD card no longer boots at all and the USB burning tool still stops at 7% formatting.
I have a full TWRP backup of my stock firmware, but no way to restore it. This is the TWRP filename in case this helps.
2019-05-19--07-24-49_q201_9377-userdebug_7.1.2_NHG47L_20171020_t
Is there any way to make something flash to the device? Even if I can just get the recovery or bootloader working so that I can flash the backup.
Thanks for your help.
Here are some photos of the board.
From the log file, it's look like unstable usb connection, have you tried other usb male to male cable? the shorter the better
keatoncray said:
From the log file, it's look like unstable usb connection, have you tried other usb male to male cable? the shorter the better
Click to expand...
Click to collapse
It's one I've used on numerous occasions with other World Cup devices in the past. It has always worked with other devices, it seems more like a problem with the device.
beachbouy said:
I have a H96 Pro Plus 3G32G ZH01-S912TVBOX-V3.0 with a green board and 7.1 firmware.
I suddenly stopped turning on, so after some research I found a solution of replacing the capacitor to 1000mf at the DC jack. Now it turns on but, wont boot. TWRP recovery was loading to splash screen but blacked out after that. I tried using the USB burning tool to flash the firmware, but it gets stuck on 7%. The SD card method also stopped at the same place and the device just powers off.
After trying a number of times with a few different firmwares, the SD card no longer boots at all and the USB burning tool still stops at 7% formatting.
I have a full TWRP backup of my stock firmware, but no way to restore it. This is the TWRP filename in case this helps.
2019-05-19--07-24-49_q201_9377-userdebug_7.1.2_NHG47L_20171020_t
Is there any way to make something flash to the device? Even if I can just get the recovery or bootloader working so that I can flash the backup.
Thanks for your help.
Click to expand...
Click to collapse
From where you found solution to change its capacitor. Was it necessary. Being an Engineer, i dont think that it could be a capacitor rather faulty usb ports or power adaptor
awaisiqbal said:
From where you found solution to change its capacitor. Was it necessary. Being an Engineer, i dont think that it could be a capacitor rather faulty usb ports or power adaptor
Click to expand...
Click to collapse
It was on freaktab. The original problem was the box not turning on and the new capacitor worked for that. But unfortunately I found that solution after I had already tried to install the firmware unsuccessfully so the box is bricked. It would probably be fine if I had not tried to flash the firmware.

Please help my pc does not recognize my new tv box t95q 9.0 amlogic s905x2

Hello friends, I need help please, my tv box t95q which is one of the new ones in quotes, I installed several firmware to paret of yours that only failed me in wifi and I like them a lot and it turns out that I installed one of tanix x3 and between with the pc and the amlogic application and now the pc does not recognize me, the tv box or the system of installing via sd card does not turn on the blue light anymore and it does not give or image I have seen that there is a method making a small short with the tv Box disassembled but I saw it and it was another tv box and I don't know where I should do it in mine if you know something and can help me please I appreciate it very much
Ho, you would need to use mask rom mode, this will force your box to be detected in USB burntool, this is achieved by shorting 2 pins on the nand flash usally

Help to unbricked the tv box a95x f3 air (amlogic s905x3)

I received the tvbox with a problem with wifi and bluetooth, I contacted the seller and he sent a firmware for me to fix it, but now the device is not identified on the PC, it does not recognize the PC's USB, after I I did the process, the device does not show any sign of life, because a firmware that was not his was installed, and the device bricked, how can I solve it, can anyone help me?

Categories

Resources