My sister's Le Max 2 screen is broken and fingerprint scanner doesnt work :/. It started having touch screen problems and weird lines and is now dead. I ordered a replacement screen off aliexpress. Was wondering how difficult is it to remove broken screen and install screen? I saw some videos, but none are in english (mostly indian or chinese or spanish vids). Also, I ask local cell repair shops, but they only know major brands. It kinda of sucks she has bad experience with this phone with the screen and fingerprint scanner.
My Le Max 2 still works great and no problems.
Also, videos I saw seem easy, however putting it back together such as using glue or tape to hold the new screen in place? Which do you use? I don't have a heat gun I saw some vids heating the sides before removing screen. Any help or tips or videos would be appreciated.
DB_Gohan said:
My sister's Le Max 2 screen is broken and fingerprint scanner doesnt work :/. It started having touch screen problems and weird lines and is now dead. I ordered a replacement screen off aliexpress. Was wondering how difficult is it to remove broken screen and install screen? I saw some videos, but none are in english (mostly indian or chinese or spanish vids). Also, I ask local cell repair shops, but they only know major brands. It kinda of sucks she has bad experience with this phone with the screen and fingerprint scanner.
My Le Max 2 still works great and no problems.
Also, videos I saw seem easy, however putting it back together such as using glue or tape to hold the new screen in place? Which do you use? I don't have a heat gun I saw some vids heating the sides before removing screen. Any help or tips or videos would be appreciated.
Click to expand...
Click to collapse
As far as I know, you'll go nowhere without a heat gun, since the screen is heavily glued. You should look for more videos, since (as far as I remember from reading here) it's very easy to break the original screen or the replacement if you don't do things properly.
jman0 said:
As far as I know, you'll go nowhere without a heat gun, since the screen is heavily glued. You should look for more videos, since (as far as I remember from reading here) it's very easy to break the original screen or the replacement if you don't do things properly.
Click to expand...
Click to collapse
Will a hair dryer work? lol
DB_Gohan said:
Will a hair dryer work? lol
Click to expand...
Click to collapse
Nope A hair dryer is to weak for this job, in the same way a heat gun would be too much to dry your hair (you'd most probably get severely burnt).
i pulled mine off and it broke!
i used a heatgun and it does help but you have to be carefull to not overheat it. you can destroy parts of the body (upper and lower side are not metal) and the screen easy by overheating. next time i use an infrared thermometer. i think a hairdryer can do it, depends on how hot it gets. if your screen is already broken, there's nothing else to worry about. i just used heat and a 6€ suction pump (very strong). next time i know better, i wont ruin another one.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
edit: look at the black stuff at the picture below. its not a hardened glue, more like window putty but more sticky (if heated up at least). if you put the old screen back it will stick together strong. a new screen may need some adhesive or tape. my screen will arrive in a few days, i plan to use double sided foam tape. i think 2-3 millimeters thickness will match. i will put 4 pieces into the corners and one in the middle (if neccessary at all).
when opening it, i inserted a razorblade (just 2-3 millimeters) and carefully cut around the screen while lifting a bit with the pump. if you pull with too much force it will break! you will not see it untill the backlight of the screen is on.
If your screen is already broken you have one less concern.
It's not that hard to replace screen, I have removed mine when I was repairing FP scanner, you can definitely do it with hair dryer, you will need a suction cup (usually they send one with replacement screen) and a razor to help lift screen also you will need double sided sticky tape.
When i was changing my FP sensor i damaged screen and had some dead pixels about 2x1 mm it was probably from heat or dent on some screws because I wasn't really careful.
Ps: replace FP sensor if you open your phone it costs about 6-7$ on aliexpress.
Screen that I used:
https://www.aliexpress.com/item/Gol...X820-X821-X822-X823-X829-LCD/32772633485.html
FP:
https://www.aliexpress.com/item/Fin...x-2-X820-Snapdragon-820-Quad/32797969465.html
video that may be helpfull: https://www.youtube.com/watch?v=f_LExkf89z0 Use razor instead of fingernails.
here is what it look like:
looks intact...
...but it isn't!
---------- Post added at 11:39 AM ---------- Previous post was at 11:30 AM ----------
lopusina said:
If your screen is already broken you have one less concern.
It's not that hard to replace screen, I have removed mine when I was repairing FP scanner, you can definitely do it with hair dryer, you will need a suction cup (usually they send one with replacement screen) and a razor to help lift screen also you will need double sided sticky tape.
When i was changing my FP sensor i damaged screen and had some dead pixels about 2x1 mm it was probably from heat or dent on some screws because I wasn't really careful.
Ps: replace FP sensor if you open your phone it costs about 6-7$ on aliexpress.
Screen that I used:
https://www.aliexpress.com/item/Gol...X820-X821-X822-X823-X829-LCD/32772633485.html
FP:
https://www.aliexpress.com/item/Fin...x-2-X820-Snapdragon-820-Quad/32797969465.html
video that may be helpfull: https://www.youtube.com/watch?v=f_LExkf89z0 Use razor instead of fingernails.
Click to expand...
Click to collapse
how is the quality of your screen compared to the factory one?
is it original or third party?
i spent slightly more because it looks absolutely like the original (sticker and labeled O-film on the backside), at least on the pictures i've seen.
Gesendet von meinem Le X820 mit Tapatalk
For now I haven't noticed any difference in screen, it is quality one but I doubt that is original.
Also replacement FP is good working for 3-4 months now, it only has some problems when it's greasy.
i must correct myself. the one i ordered is even cheaper. well, maybe they are all from the same factory.
Gesendet von meinem Le X820 mit Tapatalk
I would rate it as a quite difficult - very difficult repair as they go. Not impossible but no doddle either.
it depends on what tools/technique you use.
i would rate it pretty easy although i ruined the first screen.
to my defence i must say that i did it late in the evening after a few beers ;o)
i just couldn't wait and then regretted it...
now i have 2 x820. that's ok, will be back in job in a week, working as it-servicedesk employee/field technician. one for spare, just in case...
Gesendet von meinem Le X820 mit Tapatalk
Yea, original screen is dead/with few cracks already. Yea I bought one LCD say it comes with tools with the tape I think. Also, is it hard replacing the FP reader, would I have to dissemble more stuff to get to it? Otherwise I'll just replace screen.
Actually it's easier than replacing the screen, you will need to remove battery and motherboard to get to it, but it's nothing very hard. Screen replacement and opening phone takes most time. So as I said before, if you're opening phone already, replace both things screen and FP.
got my screen today. there is no difference in quality as far as i can tell.
Gesendet von meinem Le X820 mit Tapatalk
A.N.Droid said:
got my screen today. there is no difference in quality as far as i can tell.
Gesendet von meinem Le X820 mit Tapatalk
Click to expand...
Click to collapse
How did you put screen together, did you use tape or glue? My LCD screen came in today came with tools and some tape, but debating if I should wait and order fingerprint sensor.
Heyyo, I just replaced mine with this one I ordered and haven't noticed any quality differences and still says 1440x2560 resolution
https://www.aliexpress.com/snapshot...&orderId=85749574743245&productId=32818353673
It also came with the capacitive keys which is awesome since mine stopped working when I broke my screen.
I used a heatgun and a super cheap suction cup and some rubber gloves because damn the phone was hot.
It didn't come with the double sided adhesive tape so I ordered this one
https://www.amazon.ca/dp/B00PVWMTA6/ref=pe_3034960_236394800_TE_dp_1
It was really easy to cut and put it back together. The only part that was hard was that initial heating the screen enough and separating it from the body of the device.
DB_Gohan said:
How did you put screen together, did you use tape or glue? My LCD screen came in today came with tools and some tape, but debating if I should wait and order fingerprint sensor.
Click to expand...
Click to collapse
mine also came with tools, tape and aven a screen protector. i used the tape in one piece. it sticks together strong. if you are going to replace the fp sensor, then don't use the tape now. you will most likely break your new screen when you pull it off a second time.
Gesendet von meinem Le X820 mit Tapatalk
I replaced both LCD and FP sensor. Broke my LCD while attempting to fix FP sensor the first time. Use a cheap small suction cup not the puller. I broke mine using the big puller. Also no need to heat it up. Few drops of 99% Isopropyl alcohol along the seams loosen up the adhesive. This is safer way to do it than heat gun method. FP sensor works great now but I lost my compass feature. Anybody can confirm their compass is still working after changing the LCD and FP sensor?
works after replacing screen, dont know about fp sensor.
Gesendet von meinem Le X820 mit Tapatalk
The fingerprint scannor that I got, and replaced does not work. Is there certain way to install the fingerprint sensor??
Related
So there's been a lot of questions on how to properly replace the LCD and/or Digitizer.
I bought my digitizer (v0.3) from www.all4cellular.com . The SKU for the digitizer I got was 440002396. If you order, call AND email their support to ensure you get a V0.3. I can not guarantee that they have them now. I bought my LCD ( still waiting) from eBay, a Chinese reseller. I've been waiting over a month for it now.
First off, you have to determine if the LCD or digitzer is busted.
1 - If you can't see anything on the screen, everything is full of lines and colorful you have a busted LCD, OR the cable may have come loose. Keep reading.
2 - If you can view the tablet and all it's goods, still use some touch stuff then your digitizer is busted.
3 - If you can't turn see anything on the LCD, the screen is full of cracks then chances are they are both busted.
4 - If you turn on the Prime, the screen is black, or anything else, either it's bricked or the LCD died. Get a mini-HDMI cable, hook to a TV and check it out.
So, you've determined that you have a busted ass screen. Yay
[COLOR=RoyalBlue)"]Disassembling : [/COLOR]
To remove the LCD/Digitizer from the backing you have to look at the 2 tabs that have rubber in them on the bottom of the tablet. There is a thread here on how to do it so I won't go further : http://forum.xda-developers.com/showthread.php?t=1479664
OK! Now you have that apart. Set your TF201 half with all the goods in a safe place. Might not hurt to use the internal switch to power it off. Post #2 in the above link shows how to do it. It's a small switch. Be careful from here on out. Disconnect the LCD and digitizer ribbons from the rear case. The digitizer ribbon comes off the backing, and the LCD will come off of the LCD screen itself (you have to reuse it, one does not come with any replacement LCD screens).
So now you have your TF201 in 2 pieces. Great
Lay the screen on a flat surface. DO NOT BEND THIS. The LCD will easily crack and bust. I was in a rush to do this and cracked my LCD. If I was to do it over again, I'd find a hardcover book of the same size, place it on the LCD to minimize any bending.
First, unscrew the screen from the digitizer frame (keep these somewhere safe), bend the tabs up out of the way. Take a plastic tool, if you have on, and take it and slip it between the 2 sided tape on the LCD. Here is a picture so you can see just how little you need to pry off.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I would 100% recommend doing this with a space heater blowing on it to soften the tape, using a guitar pick or other hard slim piece of plastic to go around the edges. DO NOT flex the LCD up to see if it's cutting, do not put pressure on the back of the LCD. If you feel comfortable, you can use a Exacto knife (or scalpel) to cut it off.
When I was taking my busted LCD off after I realized my screen was broken I used a scalpel for part of it. I didn't give a crap as both LCD+digitizer were broken. If both are broke on yours, don't worry about being careful.
Here is a meh video showing a bit of it :
http://www.youtube.com/watch?v=jRU3AIWvXGY
Alright! So now you have the LCD and digitizer separated, w00t. If your LCD was broken, put the new one on. If it's still good, and the digitizer need replacing keep going. The hard part is over, now it's just the picky part.
I can not stress this enough : Any digitizer you buy will NOT come with the frame. The frame has the wifi + GPS antennas on them, as well as the screw holes for the LCD screen. If you've thrown out your digitizer without separating them, good luck in finding another.
So now you have the Digitizer and frame to separate. This was indeed a hassle as both are paper thin. Here is a picture showing how they are assembled (Although mine aren't yet, I have them laying together). This shows them separated so it gives a really good idea of what needs to be done :
Front view :
Rear view :
OK, if the tablet were together, pic 1 would be the screen facing up towards you, pic 2 shows the rear. The digitizer glass sits on the frame, held by glue. If your digitizer is broken (shattered) or just cracked, having it sitting in front of a heat source helps TREMENDOUSLY. The glue on the tape heats up and separates nicely.
Important to remember when doing this step : If you crack the frame it does NOT matter. If you break it it does NOT matter.
Why do I say this? Simple...the frame sits behind the digitizer. When you get the double sided tape to put on it to hold the digitzer in place it will also keep the frame held together without fear of anything happening. If it breaks in 2-3 pieces just tape them back up, this is not an issue as the digitizer and LCD are what gives the front it's strength. This is the reason why the front flexes and parts break. It's a design issue (imo) and should have been made much firmer, not flexible.
When I was separating the frame and digitizer, I went in from the back first to create an opening on the outside of the frame. I held the whole thing in front of my trusted space heater, let the tape warm up then slid my exacto knife between the 2 close to a corner, and twisted the knife a bit to get them to lift off eachother. Once I had a small gap, I pulled the knife out from the back and went in from the front around the edge. The reason I did this was the seam that you have to go into is a ***** to find, going in from the rear negates busting the frame and marking it up, plus it's a crapload easier to start this way.
Note : When doing this, it helps to keep a few pieces of paper the same length of the sides you're cutting (or cards). The tape glue resticks, sticking the paper or cards in keeps it separated nicely.
Here is what you'll be left with :
So now you have the LCD off the back of the digitizer, the digitizer and frame separated. It's at this point where you have to decide : Do I want this to be stuck back together like it was when I got it, or shall I use something a little more workable in case it decides to pull the same breaking stunt?
Pick your tape to re-assemble accordingly. I myself am using double sided permanent scotch tape. It's nice and sticky, but if necessary I can remove it easily in the future to fix any problems. Jgrimoldy suggested this because when you put it back together dust might slide in between the digitizer and LCD, and I 100% agree.
Putting back together :
Easy enough. Lay the frame down, apply the tape where it needs to be. Trim as necessary. Don't worry about having to touch the tape while trmming it, or it sticking out a bit. As you can see in the Rear View photo up there, you have plenty of lee-way. I would suggest leaving the plastic on the digitizer backing right up until you are ready to seat the LCD back on.
When you get to placing the LCD back on, a can of air might help a bit, or a cloth use to wipe off glasses. The LCD on the digitizer appears to have a foam type tape on it, it's your discretion if you peel it all off to clean it up nice (meh) or leave a layer of foam on it, place 2 sided tape over it and reassemble it. Personally, I'd leave the old foam tape on it (peel off any glossy layer showing) and put 2 sided back on it. Screws hold it in place and tighten it down anyways. The foam closes any gaps that let in particles.
If it's a new LCD and has plastic on it, hold the LCD upside down above the digitizer, remove the plastic off of it then off of the digitizer. Any dust in the air should be blocked off from falling on the digitizer. Have a quick peek at both, then stick them together. I am not totally sure on this step yet as I do not have a LCD to try with (yet). Most eBay LCD's I find appear to have some sort of trim around the edges, so I imagine all that's needs is a bit of tape placed around it, remove the plastic and slap it on.
So there you have it, how to take it apart and put back together.
I came to post a new topic but this might be what im after.
I
Maybe yoy could suggest if its the digitiser or not?
Thanks
Sent from my GT-I9300 using Tapatalk 2
shoutman said:
I came to post a new topic but this might be what im after.
Maybe yoy could suggest if its the digitiser or not?
Thanks
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
The digitizer cracks could be seen easily and do not affect the LCD display. Looks like the LCD ribbon is loose on that. Open it up and try to see if playing with the ribbon fixes it. Usually if the LCD is cracked the whole screen is gone bonkers.
shoutman said:
I came to post a new topic but this might be what im after.
I
Maybe yoy could suggest if its the digitiser or not?
Thanks
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
It apprears that your LCD got damaged. It's definitely NOT your digitizer. Your digitizer would be visibly cracked and it would not affect the image.
Most likely, your LCD got cracked. In my experience, and I've been a professional tech for decades, it's not a connection issue. Usually when you have a bad connection, your screen will have a substantial tint (red, green, or blue) or it would not work at all. When you have an isolated issue like you have shown in your picture where the whole screen isn't affected, it's a damaged LCD. Depending on where the LCD gets damaged, it can affect all or part of the screen (and it's often much more likely to be just a part of the screen).
Sorry to say.
Jgrimoldy said:
It apprears that your LCD got damaged. It's definitely NOT your digitizer. Your digitizer would be visibly cracked and it would not affect the image.
Most likely, your LCD got cracked. In my experience, and I've been a professional tech for decades, it's not a connection issue. Usually when you have a bad connection, your screen will have a substantial tint (red, green, or blue) or it would not work at all. When you have an isolated issue like you have shown in your picture where the whole screen isn't affected, it's a damaged LCD. Depending on where the LCD gets damaged, it can affect all or part of the screen (and it's often much more likely to be just a part of the screen).
Sorry to say.
Click to expand...
Click to collapse
I had that happen to mine with the ribbon loose Jgrimoldy (what you see in the pic), then it'd turn green randomly. Pushed the cable back in and problem solved.
Nightpath said:
I had that happen to mine with the ribbon loose Jgrimoldy (what you see in the pic), then it'd turn green randomly. Pushed the cable back in and problem solved.
Click to expand...
Click to collapse
I'd, of course, check the cable first. And definitely before ordering a replacment LCD. I have strong doubts and hope for the best.
Thanks for tge reply. How much is a replacement lcd going to cost?
Sent from my GT-I9300 using Tapatalk 2
shoutman said:
Thanks for tge reply. How much is a replacement lcd going to cost?
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
In the neighborhood of $100. If your order from China, significantly less, but the delivery delay will be measured using the geologic time scale. If you order from the U.S. (assuming you're in the U.S.), prolly a bit more, but you'll likely have it the same week.
If it turns out that the LCD is broken (which I hope is not the case), the MUCH harder part will be dis-assembling your Prime and removing the current LCD while not breaking your current digitizer.
If you have patience, reasonable dexterity, and are mechanically inclined, it's not a difficult job. Let's put it this way: If you can change a tire, replace a light switch (safely), or put RAM in a desktop PC, this should not be a big deal. If you usually find friend/neighbor/relative to do these things for you, well...
Jgrimoldy said:
In the neighborhood of $100. If your order from China, significantly less, but the delivery delay will be measured using the geologic time scale. If you order from the U.S. (assuming you're in the U.S.), prolly a bit more, but you'll likely have it the same week.
If it turns out that the LCD is broken (which I hope is not the case), the MUCH harder part will be dis-assembling your Prime and removing the current LCD while not breaking your current digitizer.
If you have patience, reasonable dexterity, and are mechanically inclined, it's not a difficult job. Let's put it this way: If you can change a tire, replace a light switch (safely), or put RAM in a desktop PC, this should not be a big deal. If you usually find friend/neighbor/relative to do these things for you, well...
Click to expand...
Click to collapse
Im from ireland... and think I'll try find someone to fix it for me as I have a history of making things worse when trying to fix them.
Sent from my GT-I9300 using Tapatalk 2
I ordered one from China well over a month ago, still have yet to see it but that's no surprise seeing as I'm in Canada. The bad thing about ordering from China is that they never want to give your money back. If you do go this route, order from eBay, then after the shipping time is over demand your money back on the first day that way they know you mean business.
I can't figure out whether my lcd or digitizer (or both) are broken. The screen is fully responsive, the colors are perfect, but if you look closely you can see the crack. You can also feel it with your fingers. The crack arised after clashing against a wall.
Atm it's not very disturbing, but i fear the crack might grow...
ozer86 said:
I can't figure out whether my lcd or digitizer (or both) are broken. The screen is fully responsive, the colors are perfect, but if you look closely you can see the crack. You can also feel it with your fingers. The crack arised after clashing against a wall.
Atm it's not very disturbing, but i fear the crack might grow...
Click to expand...
Click to collapse
It's the digitizer. If you can feel it with your fingers, it's definitely the digitizer. It's impossible to crack the LCD without having a significant effect on the image. Sorry to say that the crack will likely spread. Unless you're unrealistically careful with your TFP, it's almost guraranteed to spread.
The saddest thing happened today.
Took my TFP out today, had it sitting in the back of my car. My brother got in, his snowshoes TOUCHED my ****ing TFP and the digitizer broke. Again.
I'm replacing it 1 last time, going to sell the PoS once the case gets to me and get a different tablet. The weakness of that asshole digitizer just astounds me.
There's a nice tough looking Acer Iconia tablet with a Tegra 3 in it, it's 7" though but I'm through with this tablet.
OK, i have a question but it needs some background first:
i bought a DNA from the local Craigslist, the ad plainly said that the screen was cracked AND that they already had the replacement digitizer (i had not done enough research at this time, obviously or i wouldn't be here). So i love the phone, read all sorts of awesome reviews etc. I get home, i proceed to take the DNA apart (i have done this with multiple iPhones, and a couple other phones as well for various fixes, so it's not foreign to me)
so, i finally reach the screen, and come to realize that the LCD is FACTORY GLUED to the Digitizer.
so, my question is this, can i:
1. Order JUST an LCD and install it WITH the Digitizer/Glass that i have already (from the Craigslist seller) or
2. do i HAVE to order the WHOLE ASSEMBLY, and somehow FIND a way to sell this Digitizer? (and of course, as any good forum needs, WHY?)
hmm, seems like more than one question, but you get the idea... if i left any pertinent information out, just let me know.
EDIT: ok, since it's sunday i'm holding out on ordering anything, but before i go to bed tonight, imma order the LCD, to use with the Digitizer i already have... (do i need to glue them together or something?) unless someone has a good reason to do otherwise...
xeonight said:
OK, i have a question but it needs some background first:
i bought a DNA from the local Craigslist, the ad plainly said that the screen was cracked AND that they already had the replacement digitizer (i had not done enough research at this time, obviously or i wouldn't be here). So i love the phone, read all sorts of awesome reviews etc. I get home, i proceed to take the DNA apart (i have done this with multiple iPhones, and a couple other phones as well for various fixes, so it's not foreign to me)
so, i finally reach the screen, and come to realize that the LCD is FACTORY GLUED to the Digitizer.
so, my question is this, can i:
1. Order JUST an LCD and install it WITH the Digitizer/Glass that i have already (from the Craigslist seller) or
2. do i HAVE to order the WHOLE ASSEMBLY, and somehow FIND a way to sell this Digitizer? (and of course, as any good forum needs, WHY?)
hmm, seems like more than one question, but you get the idea... if i left any pertinent information out, just let me know.
EDIT: ok, since it's sunday i'm holding out on ordering anything, but before i go to bed tonight, imma order the LCD, to use with the Digitizer i already have... (do i need to glue them together or something?) unless someone has a good reason to do otherwise...
Click to expand...
Click to collapse
I just broke my screen
Was wondering what you came up with on this. I ordered the glass, and im assuming mine is glued too.
What did you end up doing?
Same boat here too. Just broke my screen earlier this afternoon. I called one place (ubreakifix.com) and they won't touch a DNA due to the glue issue. Anyone gotten one repaired?
Sent from my HTC6435LVW using Tapatalk 2
yearn2burn said:
Same boat here too. Just broke my screen earlier this afternoon. I called one place (ubreakifix.com) and they won't touch a DNA due to the glue issue. Anyone gotten one repaired?
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
FIRST: i HIGHLY recommend you get the LCD AND Digitizer assembly to avoid all this headache I describe below.
i wrote a HUGE reply last night, around midnight Mountain time, only to press 'preview post' and a page come up saying the website is down temporarily or something... and it was all lost... anyway...
i have my phone in a usable state, but only after 3 tries, and am still planning to open it up again to put more 'finishing touches' in there;
first time i opened it up: removed broken screen/LCD, at this point i didn't know that the LCD was glued (original post). So i ordered the LCD like i said i was gonna do, and the first time i put it in, i tried to hot glue it into the frame, this didn't work for a couple reasons; it was allowing light in on the sides of the LCD and it was allowing particles in on top of the lcd under the glass (very irritating).
EDIT: just wanted to add, that the screen is stuck to the frame, it SEEMS to be glue, but once you get it apart, you see that it's just really strong double sided tape, and you have to heat it up to get the glass off of the frame.
second time i opened it up: i decided to super glue the LCD to the digitizer (only used 4 spots of glue), this caused a pressure problem, still not sure why, but it was like the LCD pressure when you put your finger on a non-glass laptop screen (similar anyway).
Third time i opened it up, i figured i would follow a similar process of the HTC Evo 4g that i fixed for a friend, and i had a roll of REALLY THIN double sided tape left over (you can find the tape on amazon, just search for "2mm 3m adhesive sticker tape"); my first try i just put a strip of tape on the top of the glass, at the lowest i could without it going into the 'viewable area' and the same on the bottom, i stuck the lcd on here lightly, didn't push it down yet so i could see if there were any problems, and there were. The LCD likes to flex slightly, so i needed some tape on the sides to keep it from bowing up against the glass, and causing another 'pressure spot', so i added one small strip of tape on both sides to help with that, and it's working really well right now
THIS is where my phone stands as of this writing.
I'm still planning on opening it up yet again (getting good at it lol) to add more tape around the sides AND (this is important if your annoyed by little things) CUT THE EXCESS TAPE that is sticking out past the LCD as this holds the glass up from the frame by a small amount, but it's enough to be annoying. I also want to say DO NOT simply run a razor blade down the side of the LCD to cut the excess tape off as you'll cut the TINY Digitizer connections underneath the tape, and then you would have to get a whole 'nother digitizer and nobody wants to do that.
as always, this is just my opinion and what i've found ON MY PHONE, so if anything here causes damage to your phone, i'm not responsible.
Your superglue mention caught my eye. I made that mistake several years ago with a device that wasn't touch screen. what I didn't plan for was the fumes. As the gasses evaporated they sort of melted/etched the glass or plastic around them. The pressure you mentioned could it be from the superglue or fumes breaking the material down?
Sent from my HTC6435LVW using Tapatalk 2
I have also tried seperating the digitizer from the LCD and phone itself. There seems to be the double sided tape only on the LCD. Then there is a different adhesive on the top around the camera. These pics may show it a little better.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I have yet to find a digitizer with the adhesive already on it. I'm waiting on adhesive for a note 2 which I should be able to trim to fit. Replacing the whole digitizer assembly is easier but a lot more expensive.
krazya said:
I have also tried seperating the digitizer from the LCD and phone itself. There seems to be the double sided tape only on the LCD. Then there is a different adhesive on the top around the camera. These pics may show it a little better.
View attachment 1946508
View attachment 1946509
I have yet to find a digitizer with the adhesive already on it. I'm waiting on adhesive for a note 2 which I should be able to trim to fit. Replacing the whole digitizer assembly is easier but a lot more expensive.
Click to expand...
Click to collapse
I should have my glass in tomorrow or friday. Will report back.
CharliesTheMan said:
Your superglue mention caught my eye. I made that mistake several years ago with a device that wasn't touch screen. what I didn't plan for was the fumes. As the gasses evaporated they sort of melted/etched the glass or plastic around them. The pressure you mentioned could it be from the superglue or fumes breaking the material down?
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
i used really old superglue, so it took like an hour or some-such to dry, but i think the pressure was from glueing it in the wrong place, and the frame putting pressure on it somewhere. But you could be right too, either way, superglue is NOT a good idea
So the digitizer and LCD can be pulled from each other? Just got to be careful?
Sent from my HTCONE using Tapatalk 2
sorry about the half off topic question
if i will order LCD that already come with digitzier attached to him.
there is a problem to replace the old lcd & digitizer ?
cuz as i read here, there big problem is to replace only the digitizer..
incident said:
if i will order LCD that already come with digitzier attached to him.
there is a problem to replace the old lcd & digitizer ?
cuz as i read here, there big problem is to replace only the digitizer..
Click to expand...
Click to collapse
correct, the only problem is if they're separate, if you order the whole assembly, Digitizer and LCD already glued together (recommended), then the only issue you'll have is getting the broken glass off of the frame's adhesive, just be careful, use heat, but not too much because the frame is NOT metal, it actually doesn't take much to soften that frame's adhesive, i used the heat off my little desk lamp, worked great, could only do one 'section' of the phone at a time, but that's all you need.
xeonight said:
correct, the only problem is if they're separate, if you order the whole assembly, Digitizer and LCD already glued together (recommended), then the only issue you'll have is getting the broken glass off of the frame's adhesive, just be careful, use heat, but not too much because the frame is NOT metal, it actually doesn't take much to soften that frame's adhesive, i used the heat off my little desk lamp, worked great, could only do one 'section' of the phone at a time, but that's all you need.
Click to expand...
Click to collapse
Thanks for your answer, one more question please..
The screen himself - that i will pull out of the phone, isnt glued to the body of the phone?
incident said:
Thanks for your answer, one more question please..
The screen himself - that i will pull out of the phone, isnt glued to the body of the phone?
Click to expand...
Click to collapse
Yes it it stuck to the body, but no, it's not glue, it's just really strong double sided tape, and needs heat to help it let go of the pieces
hey,
I know this thread is over a month old but I recently just shattered the digitizer on my DNA as well and haven't really seen one of the most important questions answered.
For those of you that replaced the the entire assembly, is the quality of the OEM LCDs as good as the original? I know it's extremely time consuming to melt the adhesive and have everything back in one piece, but if the quality of the S-LCD3 on the original is better than the OEM replacement ones I would spend the extra time to do it.
Shinkenshi said:
hey,
I know this thread is over a month old but I recently just shattered the digitizer on my DNA as well and haven't really seen one of the most important questions answered.
For those of you that replaced the the entire assembly, is the quality of the OEM LCDs as good as the original? I know it's extremely time consuming to melt the adhesive and have everything back in one piece, but if the quality of the S-LCD3 on the original is better than the OEM replacement ones I would spend the extra time to do it.
Click to expand...
Click to collapse
i don't believe there's a difference, OEM stands for 'Original Equipment Manufacturing', so that SHOULD mean it's the same as original.
I'm no expert tho, just a guy with a phone trying to get by on a budget.
GOOD NEWS!
the whole 'assembly' (the digitizer AND LCD glued together as it was from factory) is now down to under 100$ US on eBay!
on a side note, i dropped my phone a couple weeks ago and broke the top right corner, nothing else is wrong, just a crack in the top right corner, going from the ear-speaker to the right edge
So a few weeks ago I cracked my phone and like all others I was pretty pissed.... The digitizer worked it was just the glass I did my research and found that I would need to replace the entire thing..... But hell I bought a new glass from amazon for 10$ a dollar set of playing cards and a razor blade for another buck and used my girls blow dryer and used up half an hour of my night and presto the phone looks like new the reason for this post is to let you know that it's possible to change the glass what makes it easy is that my girl held the blow dryer as I used the cards to pry the glass of your up for the task and need help let me know
Sent from my SAMSUNG-SGH-I717 using xda premium
Wow. That is good to know.
So, you were able to heat the screen until the digitizer/LCD came off clean from the glass? How did you stick the glass back on to the digitizer/LCD?
Congrats! That is really good news. Would you be kind enough to provide more detail on the process. There are many of us that would benefit from new glass but there really isn't much in the way of tutorials. I already hit your Thanks button.
P.S. If you are kind enough to write something up I recommend a better title. Maybe something like "How to replace your glass on the Original Note" or something similar.
Yeah you usually got to heat up that glass to help it come out lose. I also got a cracked screen and I'm also waiting for it. I got my adhesive tape from China yesterday. My ? Is before I do this does the glass come with any adhesive or it will just pop right into the note?
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
There are three layers : glass, LCD, digitizer.
When I replaced my entire screen, I had to stick glass, LCD, digitizer into one piece. There were adhesives on them (at least the ones I bought did).
Then, you need few pieces of double-sided tape to stick the entire screen to the housing.
Kudos
I immediately hit the Thanks button because, as others have pointed out, it's really nice to know it can be done. Thankfully, my note is in pretty good shape. I did have a cracked screen on my BB back in the day and was able to replace the screen/digitizer. Maybe someone can post a video tutorial one day.
how i replaced the broken glass part on my note
ok guy im going to write this as best as i can and please be kind this will be the first diy post i have ever done.......
1. ok step one taking apart the phone... this is very easy you can youtube this step its really simple.....just take out the battery cover battery sim card and sd card
2.now remove all the screws in the buttome there are 9 screws .
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
.....8 of them around the phone and one of them in the middle around the part where you insert the battery....
3. this is where it gets just a bit tricky you must "pop" off the screen i used a plastic razor blade around the bazel work around the phone it should pop out without much struggel but be very careful not to bend the digitizer it can break..
4. ok once u removed the screen out of the back cover there are 2 screws connecting the motherboard removed them and disconnect all ribbon connections
5. ok this is where the tricky part begins........first of all i want to say and just to be safe that im just typing this to help out because like most i dont want to pay 200$ for a new screen and digitizer so if you try this and fail im sorry and please dont blame me...
ok start of by using your blow dryer(what i used) or heat gun and work it over the phone not to close and dont just aim it in one certain spot work around it up and down laft and right.... once you do this about a minute or two very ooh so very carefully incert ur blade at the top this is the best approach so i think...and lift up if need to ask someone to keep using the heat gun while you do this it will save you lots of time..once you start to pry up the glass it will start to crack more and more that fine....once you start to remove the glass pieces (use tweezers) try to wedge a playing card inside (the card helps out soooo much you can work it in between the broken glass and the digitizer with out harming the digitizer)....now if you can with one hand more the card down the phone and use the heat gun you will start to see the glue separate from the digitizer....just move slowly and carefully.... just keep wedging the playing card and using the heat gun.
6. by this point you should have more then half the glass removed that part took me about 10 mins.. ok one thing you have to look after once you get to the buttom is be careful once you get to the buttons (home back search menu) try not to damage the connector under the screen what i did once i got to that part was i lifted the last of the glass and carefully pulled with tweezers.....then voila!!! the glass should all be off the digitizer...
7..to clean off all the glue off the digitizer i started by using a new playing card and using the edges i scraped the screen not using to much pressure once i got off what i could then i honestly used 2 microfiber cloths one i sprayed windex multipurpose on it(the cloth not the phone) and started to rub it gently that should help remove just about all of it then i made sure the edges where clean no glue on sides no little broken pieces of glass on buttom or top of the phone where the adhesive is...then used a clean micro fiber cloth to just give it a final wipe...
8. for putting on the new glass i did not use new adhesive....nore any type of new glue....i just made sure i had everything ready to go made sure i was not missing anything...every clean no glass pieces no glue on digitizer..MADE SURE DIGITIZER WAS 100% CLEAN....theni grabber my brow dryer heated the adhesive on top and buttom of the phone got it sticky again then i quickly BUT carefully placed the new screen on applied a little bit pressure and help it for about 2 mins let go and BAM!!!! stuck on to the phone...im sure you can use new adhesive but mind my cheapness to not spend that much money...lol.....
9.now its time to connect all the ribbons back on screw the 2 screws holding the motherboard....snap back the screen onto the bezel.....screw back on the 9 screws insert your sim and sd cards power that bad boy up and hope for the best.....
so like i said before i have no prior knowledge on taking this phone apart... i have changed one other phone screen and that was an iphone but if you have done that before you know thats easy as pie...i really really hope i helped someone out there...i left my iphone to this phone and i am in love with it i compared it to an iphone and the iphone looks like a play phone my son would play with....so a crack on this beauty is a no-no.... so if your up to it buy a new glass about 15 bucks including shipping on amazon... razor blade a blow dryer and about 5 playing cards and patience and you have a new screen.....now if you live in arizona and are close or whilling to drive to my town of queen creek i can help you with this and if your screen is super bad and i mean where theres no way of using it because the glass is shattered and have a video camera and are whilling to come to my place to record a how to video i will attempt to repair your phone free of charge i have an extra screen i bought just incase i messed up but pm me and let me know for all others good luck and i hope i helped
i just used the old one
How is it that some people say is nearly impossible to get the LCD and glass separated? I got my glass screen today but u no what sucks? Apparently my wife threw away my stupid adhesive tape. I'm screwed now
Sent from my GT-N8013 using xda app-developers app
I thought it was nearly impossible, because LCD is so fragile. Any slight pressure/bend can ruin the LCD.
Technically, it is possible to separate them, cuz it is just glued together. And OP proved me wrong and everyone else who advised against the idea.
So... why don't you just buy another roll of tape?
I just did mine look took me 3 hours but works. I did scratched up a lol the lcd and overheated a part an oopsie from me but managed to place the screen back using the old adhesive on the sides heated that junk up and now I'm good since this yr I got an upgrade so I can wait lol but for future ppl trying to do this be cautious as to what object you use for the putting apart also I used wd40 to clean out the excessive adhesive
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Best if u just use rubbing alcohol
Sent from my SAMSUNG-SGH-I717 using xda premium
It's definitely nice to know a bit about the process required to fix the screen if my luck ever catches up with me. Thanks for that guide.
Sent from my AT&T Galaxy Note
In the repair guide we demonstrate how to safely tear down the HTC Droid DNA to perform repairs such as replacing a cracked or damaged Touch Screen Digitizer or LCD screen.
This guide will help you to install the following HTC Droid DNA parts:
HTC Droid DNA LCD + Touch Screen Digitizer Replacement
HTC Droid DNA LCD Screen
HTC Droid DNA Touch Screen Digitizer
Tools Required:
Small Phillips Screwdriver
T5 Torx Screwdriver
Adhesive Strips
Safe open Pry opening Tool
HTC Droid DNA Repair Guide:
It is very important that you make sure your device is powered off completely before performing this repair.
To start you will need to remove your simcard and simcard tray.
Next you will need to remove the back cover of the device using a safe open pry tool to release the clips holding it in place.
Now that the back cover is removed you will need to gently remove the black protective film covering the motherboard and internal components.
Next you will need to remove 13 small phillips screws as well as the 2 Torx T5 screws as detailed in the figure below.
After all the screws have been removed you will have a total of 5 antenna cables, 4 jaw-bone connectors, 2 pop connectors, and the battery cable to remove before you can proceed.
See figure below for screw locations and flex cable connections.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The next steps you will need to take your plastic pry tool to gently lift up the motherboard so you remove it completly. (be sure all flex cable connections have been release before attempting this)
In order to remove the upper circuit board you will need to release the front camera from the housing using your pry tool.
You will now need to remove the black film covering the power button flex ribbon so you can gently peel it away from the housing.
See figure below for reference.
Now you can gently insert your pry tool under the upper circuit board to remove it completely from the device (be cautious of the power button flex ribbon as you do not want to tear it)
You can then take your plastic pry tool and lift up the lower speaker assembly to remove it.
You will now need to take a pry tool(s) to lift up the battery from the inner housing. This battery is held down with strong adhesive so you will need to be extra cautious not to bend the battery when attempting to lift it away from the device. You may find inserting a second pry tool will give you an equal amount of leverage to prevent bending the battery.
Finally you will need to gently peel away the volume button assembly from the housing and slide its flex cable through the slot in the housing.
See the figure below for reference.
Now that all necessary components have been removed from the device you can begin the process to remove the LCD & digitizer assembly.
First you will need to use a heat gun or a blow dryer to heat up the adhesive holding the screen assembly in the frame and outer housing.
Using a setting of medium heat for roughly 30-45 second intervals just a few inches away from the device. Make sure to evenly distribute heat to the outer edges of the screen as well as the back of the housing. (Be cautious not to hover over any flex cables you do not want to damage.)
Once the adhesive has been warmed up enough you can now insert your safe open pry tool in between the seam of the housing and screen assembly to gently separate them.
Work your way around the housing by sliding your plastic pry tool along the outer edges to give you enough room to completely remove the screen from the device.
See the figure below for reference.
Notice: This repair guide is for learning purposes only and you should perform this repair at your own risk.
Thanks for this. I just put a couple deep scratches on my screen ( they're driving me nuts) and was on your site checking for price,and watched your YouTube video just 2 days ago.
I used your video tutorial to replace the display on my OG Incredible after it fried due to moisture. You provide excellent guidance and products. Thank you
Sent from my HTC6435LVW using xda app-developers app
What do you guys suggest for adhesive for this phone? No matter what I can't get the sides to stay down after replacing the screen because the bezel of the housing is so small.
Sent from my Galaxy Nexus using xda premium
zcs72 said:
Thanks for this. I just put a couple deep scratches on my screen ( they're driving me nuts) and was on your site checking for price,and watched your YouTube video just 2 days ago.
I used your video tutorial to replace the display on my OG Incredible after it fried due to moisture. You provide excellent guidance and products. Thank you
Sent from my HTC6435LVW using xda app-developers app
Click to expand...
Click to collapse
You're welcome we're glad we could have helped!
RhinoShock said:
What do you guys suggest for adhesive for this phone? No matter what I can't get the sides to stay down after replacing the screen because the bezel of the housing is so small.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Some times we have found that if you can lay down a slightly wider piece of adhesive on the inner bezel then using a SHARP x-acto knife or razor blade you are able to cut along the edges of the bezel to lay the adhesive down. Take your time if you attempt this method and be careful not to slice your finger. Hope this helps!
Is it easy to sperate the lcd from the digitizer? I've heard it can be pretty difficult? what would you rate the hardness to replace a cracked screen? And Any recommendations for who to get fixed with?.. Thanks for the comprehensive guide :thumbup:
Sent from my HTC6435LVW using Tapatalk 2
Dri94 said:
Is it easy to sperate the lcd from the digitizer? I've heard it can be pretty difficult? what would you rate the hardness to replace a cracked screen? And Any recommendations for who to get fixed with?.. Thanks for the comprehensive guide :thumbup:
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
It's not impossible but it can be very difficult if you are not experienced and do not have the proper tools to perform the repair. We ALWAYS suggest using the LCD+Digitizer assembly for those who are trying to repair a damaged screen themselves. The screens are bonded together and trying to separate them could lead to LCD damage or a heap of nasty glue on the LCD. Use a complete screen assembly. It may be more expensive, but it will save you a lot of hassle and potentially extra repair costs.
RhinoShock said:
What do you guys suggest for adhesive for this phone? No matter what I can't get the sides to stay down after replacing the screen because the bezel of the housing is so small.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I regularly use 3M 300LSE tape on iPod touches. They are these really thin strips placed out on a sheet. They are really strong and don't make a mess.
so..... I dropped my phone yesterday. glass is still fine, but lcd is bad(scrambled image)...
where's the cheapest place i can get a replacement lcd assembly from? as long as it's oem(doesn't have to have verizon logo)
voxigenboy said:
so..... I dropped my phone yesterday. glass is still fine, but lcd is bad(scrambled image)...
where's the cheapest place i can get a replacement lcd assembly from? as long as it's oem(doesn't have to have verizon logo)
Click to expand...
Click to collapse
Try Repairs Universe, going on ebay or amazon seems like you're gambling on quality..
onestepshort said:
Try Repairs Universe, going on ebay or amazon seems like you're gambling on quality..
Click to expand...
Click to collapse
Do you know if they give 'store credit' for broken screens? I have around 50+ iphone 4/4s screens I'd been meaning to recycle... would be nice to get credit for them towards a new DNA screen.
voxigenboy said:
Do you know if they give 'store credit' for broken screens? I have around 50+ iphone 4/4s screens I'd been meaning to recycle... would be nice to get credit for them towards a new DNA screen.
Click to expand...
Click to collapse
Honestly I am not sure. go to their site and send them an email or something www.repairsuniverse.com. they might not advertise it but it wouldn't hurt to ask.
onestepshort said:
Honestly I am not sure. go to their site and send them an email or something www.repairsuniverse.com. they might not advertise it but it wouldn't hurt to ask.
Click to expand...
Click to collapse
heh... i filled out their 'contact us' submission form yesterday & never heard back from them. tried calling their phone # but upon being connected, notified me that there is no phone support "at this point" and instructed me to fill out the contact us form.
anyway, i just tried the 'live chat' & got through to someone. so at least that works.
voxigenboy said:
heh... i filled out their 'contact us' submission form yesterday & never heard back from them. tried calling their phone # but upon being connected, notified me that there is no phone support "at this point" and instructed me to fill out the contact us form.
anyway, i just tried the 'live chat' & got through to someone. so at least that works.
Click to expand...
Click to collapse
Oh. well do they do store credit?
onestepshort said:
Oh. well do they do store credit?
Click to expand...
Click to collapse
no they don't. sending off the screens to fixitrepairparts.com ($6 each/paypal, or $7/each store credit)
unfortunately, fixitrepair only has iphone/samsung screens, so getting paypal credit & once that comes through i will use it to buy a screen from repairsuniverse
voxigenboy said:
no they don't. sending off the screens to fixitrepairparts.com ($6 each/paypal, or $7/each store credit)
unfortunately, fixitrepair only has iphone/samsung screens, so getting paypal credit & once that comes through i will use it to buy a screen from repairsuniverse
Click to expand...
Click to collapse
Good to know thanks!
Hi, I just replaced my screen assembly with a white one, red buttons. However, now the home, back, app buttons don't light. Any ideas ? thanks
findinghomer said:
Hi, I just replaced my screen assembly with a white one, red buttons. However, now the home, back, app buttons don't light. Any ideas ? thanks
Click to expand...
Click to collapse
Do you see a faint light? or none at all?
repairsuniverse said:
Do you see a faint light? or none at all?
Click to expand...
Click to collapse
It was none at all. But I pulled those reflective stickers off old one and it lights a little bit now. First two are lit pretty decent. But last icon not much at all. It was a one piece guide w three squares, one for each icon. But the third square ripped off of the strip so its independant now. Could this be why the third one isn't as bright ?
findinghomer said:
It was none at all. But I pulled those reflective stickers off old one and it lights a little bit now. First two are lit pretty decent. But last icon not much at all. It was a one piece guide w three squares, one for each icon. But the third square ripped off of the strip so its independant now. Could this be why the third one isn't as bright ?
Click to expand...
Click to collapse
It could be. It's hard to tell without pictures. Maybe you could post some?
Warning: This MOD will void your warranty. You will have to open the device for performing this MOD. Only perform this MOD if you are willing to take a risk.
I took inspiration from Zack from JerryRigEverything to make a clear back MOD of our Honor 8.
It took me around and hour to do this. The only tool I used is a razor blade and scissors.
RESULT:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Guide:
(NOTE: I am not responsible for any damage you do to your own phone.
1. Slowly remove the rear glass by heating the glass with a heat gun and lifting it with a suction cup.
(You can find many guides on removal of back glass on YouTube.)
2. Remove the connection between fingerprint scanner and the motherboard.
3. Remove the leftover adhesive on the phone.
4. Stick transparent double sided tape around the phone. Make sure you don't cover the camera lens, flashlight and laser.
5. Clean the Glass:
-You can slowly scrape off the lamination by using your finger nails or with tip of the razor blade.
(I noticed that there is a heat shield that is present on the lamination, so by doing this MOD you will loose it.)
-If you use razor blade, the glass might get scratched easily.
-Before cleaning near the fingerprint scanner, remember the orientation of the scanner.
-Use transparent double sided tape to stick the FP sensor back into its original orientation.
-Clean the whole inside of the glass and get rid of fingerprints and stickiness.
6. Reconnect the FP sensor cable back to the motherboard.
7. Stick the glass back to the phone and apply pressure around the glass to make the glass stick firmly.
I am posting this after using the phone for 3 days and as there is no heat shield, there is not much heat on the glass.
This is so head turning that many were curious about this.
MORE IMAGES (with guide)
Amazing, been searching for this but only found a Honor9 till now, gonna do it as soon as i found the Clear double side tape, good work.
kmry said:
Amazing, been searching for this but only found a Honor9 till now, gonna do it as soon as i found the Clear double side tape, good work.
Click to expand...
Click to collapse
Thanks mate. Do share your results!
Ah, hello, fellow transparent Honor 8 user!
I just did a sin.
This sin. https://imgur.com/gallery/rD6Srsd
I put that on my phone.
But, other than that, I made my phone transparent last year, and have always been screwing around with it. Here's some advice from me:
The honor logo on the glass itself can come off. Just a *little* harder scratching and it'll come off.
The shielding on the motherboard PCB is detachable. It kinda clips in place, so it can be "pulled" off. It looks MUCH better with it removed.
In fact, a lot of things can come off and be fine. The flash diffuser can be replaced with Scotch tape, the fingerprint sensor and screen connector bracket can be removed, some metal can come off...
ok maybe I lost the flash diffuser and fingerprint connector and screen connector bracket but you get the idea.
You can put anything behind that wonderful glass. I used to have a piece of paper with my name on it, but I removed it. Now I put in, uh, an ahegao image, and it's secured nicely.
That's all I have to say. Good job on this, btw, yours looks nice and secured but my back glass keeps detaching from the adhesive, no matter how much I put on. Maybe it's because the plastic layer in between is stretched out and tries to force itself out of the phone...
Noorquacker said:
Ah, hello, fellow transparent Honor 8 user!
I just did a sin.
This sin. https://imgur.com/gallery/rD6Srsd
I put that on my phone.
But, other than that, I made my phone transparent last year, and have always been screwing around with it. Here's some advice from me:
The honor logo on the glass itself can come off. Just a *little* harder scratching and it'll come off.
The shielding on the motherboard PCB is detachable. It kinda clips in place, so it can be "pulled" off. It looks MUCH better with it removed.
In fact, a lot of things can come off and be fine. The flash diffuser can be replaced with Scotch tape, the fingerprint sensor and screen connector bracket can be removed, some metal can come off...
ok maybe I lost the flash diffuser and fingerprint connector and screen connector bracket but you get the idea.
You can put anything behind that wonderful glass. I used to have a piece of paper with my name on it, but I removed it. Now I put in, uh, an ahegao image, and it's secured nicely.
That's all I have to say. Good job on this, btw, yours looks nice and secured but my back glass keeps detaching from the adhesive, no matter how much I put on. Maybe it's because the plastic layer in between is stretched out and tries to force itself out of the phone...
Click to expand...
Click to collapse
Thank you so much.
Does removing the RF shielding on the motherboard cause any problem (regarding heat or other)??
vssrinath said:
Thank you so much.
Does removing the RF shielding on the motherboard cause any problem (regarding heat or other)??
Click to expand...
Click to collapse
Not that I know of. I've had my phone near microwaves and stuff without any issues. Most of the heat is generated on the other side of the PCB, with the SoC, but that heat gets dissipated through the aluminum frame of the phone with thermal pads. In fact, once I hit a capacitor with my pliers because there's additional metal under there that I tried to remove, and the tiny capacitor got ripped off, but my phone still works fine. No issues of any sort.
Noorquacker said:
Not that I know of. I've had my phone near microwaves and stuff without any issues. Most of the heat is generated on the other side of the PCB, with the SoC, but that heat gets dissipated through the aluminum frame of the phone with thermal pads. In fact, once I hit a capacitor with my pliers because there's additional metal under there that I tried to remove, and the tiny capacitor got ripped off, but my phone still works fine. No issues of any sort.
Click to expand...
Click to collapse
Woah, will remove those shields soon.
I'm thinking to stick a carbon fiber vinyl on the battery (just like mi 8 explorer edition), or anything cool.
Could you suggest some ?
Noorquacker said:
Ah, hello, fellow transparent Honor 8 user!
I just did a sin.
This sin. https://imgur.com/gallery/rD6Srsd
I put that on my phone.
But, other than that, I made my phone transparent last year, and have always been screwing around with it. Here's some advice from me:
The honor logo on the glass itself can come off. Just a *little* harder scratching and it'll come off.
The shielding on the motherboard PCB is detachable. It kinda clips in place, so it can be "pulled" off. It looks MUCH better with it removed.
In fact, a lot of things can come off and be fine. The flash diffuser can be replaced with Scotch tape, the fingerprint sensor and screen connector bracket can be removed, some metal can come off...
ok maybe I lost the flash diffuser and fingerprint connector and screen connector bracket but you get the idea.
You can put anything behind that wonderful glass. I used to have a piece of paper with my name on it, but I removed it. Now I put in, uh, an ahegao image, and it's secured nicely.
That's all I have to say. Good job on this, btw, yours looks nice and secured but my back glass keeps detaching from the adhesive, no matter how much I put on. Maybe it's because the plastic layer in between is stretched out and tries to force itself out of the phone...
Click to expand...
Click to collapse
I did the same till recently got bored of it and bought a new blue glass cover, if you really wanna make sure the glass stays glued, you have to use transparent b7000 adhesive, and if you lost the plastic flash diffuser like me, with the glue, make a circle arround the flash, so dust dont come in to the camera and destroy it.
Here: http://imgur.com/gallery/iSd5PDp