hi everyone happy new year
pleaaaaaase i need your help. i flashed my lg ls992 rom, but when the flash ends, normally the device rebooting but my device is going off and still of, i press power button but it's still of, trying to enter to recovery mode it's the same, connect the phone to charge but nothing change it stills off and don't charge, but when i connect it to pc , it's recognized the mobile driver but the charging signal don't appears.
i tried several thing like inplug the batterie and press 30 seconds on power button.. but nothing new, no flash program recognized my device
please help me 3 days of trying and trying but not result
medja77 said:
hi everyone happy new year. pleaaaaaase i need your help. i flashed my lg ls992 rom, but when the flash ends, normally the device rebooting but my device is going off and still of, i press power button but it's still of, trying to enter to recovery mode it's the same, connect the phone to charge but nothing change it stills off and don't charge, but when i connect it to pc , it's recognized the mobile driver but the charging signal don't appears...
Click to expand...
Click to collapse
I don't have this device but, the following area of the forum is specific to your device.
https://forum.xda-developers.com/lg-g5
With that stated...
Your best bet is probably to take a look at the following thread and, if needed, post your question within that thread.
https://forum.xda-developers.com/showthread.php?t=3350648
Good Luck!
~~~~~~~~~~~~~~~
I DO NOT PROVIDE SUPPORT VIA PM UNLESS ASKED/REQUESTED BY MYSELF.
PLEASE KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
medja77 said:
hi everyone happy new year
pleaaaaaase i need your help. i flashed my lg ls992 rom, but when the flash ends, normally the device rebooting but my device is going off and still of, i press power button but it's still of, trying to enter to recovery mode it's the same, connect the phone to charge but nothing change it stills off and don't charge, but when i connect it to pc , it's recognized the mobile driver but the charging signal don't appears.
i tried several thing like inplug the batterie and press 30 seconds on power button.. but nothing new, no flash program recognized my device
please help me 3 days of trying and trying but not result
Click to expand...
Click to collapse
Sorry to hear this...
Have you the Fastboot access? How to Check:
1) Remove Battery and put it back
2) Press and hold Volume - (Volume down) and connect via USB to your PC
3) The Phone Screen should change now and you can read something about Fastboot Mode
OR
Can you set your Phone into Firmware Download Mode?
1) Remove Battery and put it back.
2) Press and hold Volume + (Volume up) and connect via USB to your PC
3) The Phone goes normaly into Download-Mode now, see it on Phone Screen
4) Open LG Bridge and go to Update and then in the Bottom right Hand side onto >Correct Update Errors< this will flash your Phone with the Stock Rom
Working for you?
Related
Hey,
I have a problem. My tablet is SGP312 has Cyanogenmod 11 (FXP247 - Android 4.4). It was bricked when I type in Terminal:
Code:
su
reboot recovery
Was turned off and will not turn on at all.
Power button = NOTHING
Power button + Vol(+) 3/10/25 secs = NOTHING
Power button + Vol(-) 3/10/25 secs = NOTHING
Power button + Voll(+) + USB = NOTHING
No LED light, It's literally a paperweight. I can't even put it into Flashmode.
Please help me!
Anyone can help me?
WeRunTheNite said:
Anyone can help me?
Click to expand...
Click to collapse
Are you sure u can't put it in to flash mode, because that's the first thing I would do
Try putting it into fast boot mode
Hold volume up button and keep holding it and connect it to the pc
If you see blue light on your tablet, it means it has successfully entered fast boot mode
Make sure all the drivers are installed
Or
Follow the following procedures
Install Sony Ericsson flash tool and install all the drivers
Hold volume down button and keep holding it and connect it to pc
Once you hear the connecting sound our Any notification on your pc saying that it is connected, go ahead and flash the ftf file
hassanman1997 said:
Are you sure u can't put it in to flash mode, because that's the first thing I would do
Try putting it into fast boot mode
Hold volume up button and keep holding it and connect it to the pc
If you see blue light on your tablet, it means it has successfully entered fast boot mode
Make sure all the drivers are installed
Or
Follow the following procedures
Install Sony Ericsson flash tool and install all the drivers
Hold volume down button and keep holding it and connect it to pc
Once you hear the connecting sound our Any notification on your pc saying that it is connected, go ahead and flash the ftf file
Click to expand...
Click to collapse
When I hold volume up or volume down and connect it to PC, light turn on in red color. Flashtool says "device connected with usb debugging off" but tablet is off!
Driver
WeRunTheNite said:
When I hold volume up or volume down and connect it to PC, light turn on in red color. Flashtool says "device connected with usb debugging off" but tablet is off!
Click to expand...
Click to collapse
in my opinion, the drivers are not correctly installed
http://developer.sonymobile.com/downloads/drivers/xperia-tablet-z-sgp311-sgp312-driver/
go to the website and download and load the drivers on your pc
its just weird that it says device connected with Usb debugging off when it is actually powered off
try charging your device, maybe the battery needs to be charged leave it there for atleast 30 mins then try the steps
let us know if you fixed it or not
hassanman1997 said:
in my opinion, the drivers are not correctly installed
http://developer.sonymobile.com/downloads/drivers/xperia-tablet-z-sgp311-sgp312-driver/
go to the website and download and load the drivers on your pc
its just weird that it says device connected with Usb debugging off when it is actually powered off
try charging your device, maybe the battery needs to be charged leave it there for atleast 30 mins then try the steps
let us know if you fixed it or not
Click to expand...
Click to collapse
I have a similar problem, I've flashed plenty of devices before, never briked a thing.
By unloking the bootloader the data partition of my brand new tablet Z went corrupted. I've tried to flash several firmware but none was succesfull (couldn't format data...), and finally it get totally bricked! no light, nothing... I was not even able to put it in flash mode (no light ever!).
I've tried after a while, I've read with some other Xperia devices, it would be possible to recover it after some time, by letting the battery die, then use some rubber trick to keep vol- pressed... you can find it in XDA forums what I'm talking about. However after a month my tablet was still dead. no light, no nothing!
I've sent it to warranty and the just said that "an alternative firmware was flashed" (voiding the warranty) "and has rendered the logic board unusable".... and they have to order a new unit!!
I feel so surprise that even the cheapest chinese tablet have an harware mode that allow to reflash and resuscitate it back to factory... even if the firmware is completely screwed, and a 600$ tablet for a simple bootloader unlock got totaly bricked.
I wonder if there is an "hardware" way to recover the tablet (I saw it's pretty easy to tear down the Xperia tablet Z), by directly accessing the NAND... or by accessing some PIN (well I know sony would have not leaked such information)
After an unsuccessful CWM flashing attempt, my phone it getting the infamous "SECURITY ERROR" message. Now, I tried the offline KDZ method, but like many other JB users, the flashing got stuck at 15%. So, finally I decided to use the online flashing method using the new LG Support Tool. But the sad part is that I am suffering from a low battery issue.
So, does anyone know how to charge a soft bricked Optimus L9?
Any help would be highly appreciated.
I'm just guessing but you could try removing battery for 15-20 sec then inserting it and connecting your phone to charger. If that doesn't work, try installing x and u using fastboot that try same process with removing battery...
You can always use another phone to charge your battery
aod990 said:
If that doesn't work, try installing x and u using fastboot that try same process with removing battery...
Click to expand...
Click to collapse
I tried the fastboot method too, but I face a problem while doing it. The OAMP device which shows in the devices manager keeps disconnecting and reconnecting. So then I unplugged the USB and clicked on "show hidden devices" and then installed the drivers by clicking on the OAMP shown there. But when I plug in the USB again, the same reconnecting starts happening. Do you know a solution to this?
You should follow this post...
Connecting and disconnecting of OMAP device is normal, but it is important that it's recognized in device manager...
FINALLY UNBRICKED....
Sincere thanks to all those wonderful people who have made so many tutorials. I failed to do the offline KDZ flash as well as the fastboot method (as I have mentioned above). But anyway, I did unbrick my phone. I flashed using the online method as follows:
Download the latest LG Mobile Support Tool.
Connect your phone in "Software Upgrade" mode (by holding the Vol UP button while connecting the USB).
In the LG Tool, click on "Options > Recovery". Getting the recovery to open is a confusing task. You have to fiddle around with the USB Drivers options a bit.
Now, let the LG Tool do it's magic [In my case, it downloaded a 592MB file]
CAUTION: When the upgrade tool is in it's last stage, the phone will restart at around 93%. When it restarts, you quickly need to press and hold the Vol UP button to again enter the "Software Upgrade" mode, otherwise the upgrade will not succeed and you will get an error. If you get that error message, don't worry, the Tool will tell you how to "RETRY" (don't worry, no file will be downloaded from the internet this time )
REGARDING THE BATTERY ISSUE:
When my phone got bricked it was at around 65%. Now, when I finally unbricked it, I am seeing 83%!! So, either the phone charged when it was connected in the "Software Upgrade" mode, or it charged when I plugged the charger in the wall socket for half an hour. In any case, if your battery is dead (and phone is bricked) try to charge using a wall socket first. When you do this, the phone will automatically switch on and you will again get that sad "SECURITY ERROR" message. Just switch off the phone when you get this. Let the phone be plugged in for some time to let it charge. [NOW I AM NOT SAYING THAT IT WILL CHARGE AS I HAVE MENTIONED THE TWO POSSIBLE WAYS ABOVE, but hey, it's worth a try!] If your phone switches on, good job! Otherwise, try to charge via the USB by connecting to your PC/Laptop by going into "Software Upgrade" mode.
I just hope that the above points will help some unlucky soul who was stuck like me Remember, never give up!
Thanks to all for the tips my optimus was running fine at about 65 percent charged and just shut off. I bought a new battery charged all night in the wall still nothing. I can't get my computer to see it. when i hold power and vol down I can hear the computer make sounds like it recognizes it though
david244us said:
Thanks to all for the tips my optimus was running fine at about 65 percent charged and just shut off. I bought a new battery charged all night in the wall still nothing. I can't get my computer to see it. when i hold power and vol down I can hear the computer make sounds like it recognizes it though
Click to expand...
Click to collapse
Can you enter s/w upgrade mode? ( Press and hold VolumeUP button and insert USB cable into phone )
aod990 said:
Can you enter s/w upgrade mode? ( Press and hold VolumeUP button and insert USB cable into phone )
Click to expand...
Click to collapse
I don't think so, just now did it and I can here the computer making sounds like it recognizes it but nothing shows on the phone
p.s. guessing my board went bad, no worries though just first time I ran into something I couldn't fix if the cpu would read it or any software I might have a chance
If you still have warranty you should take your phone to service, if not then try installing fastboot drives and flashing x and u then try offline kdz flash...
aod990 said:
If you still have warranty you should take your phone to service, if not then try installing fastboot drives and flashing x and u then try offline kdz flash...
Click to expand...
Click to collapse
well I did the fastboot option i found but not sure if I did it right, I downloaded the omna files but not sure if the right ones but I did get the screen to show a faded out lg symbol not sure if that means anything
Use fastboot from here. You have here how to install fastboot drives. Then follow instructions from this page.
Read instructions carefully and you should be able to successfully unbrick your phone.
So i was using RessurectionRemix (a version from last month) and recovery twrp 3.1.0-0 and the phone was working great!
Yesterday i left my phone charging over night and in the morning i wake up to my phone bootlooping!
So i tried different things including everything it says here https://forum.xda-developers.com/le-max-2/how-to/guide-hard-brick-fix-qualcomm-hs-usb-t3492949 without luck
I can get it into recovery and fastboot but as soon as i let the key combination go the phone stops and just shows a black screen (screen is on) and i cant get into qualcomm recovery to flash!
And the only way to shut off the phone is by holding power + vol up + vol down!
Any solution or suggestions?
Use flashone method to unbrick
md07 said:
Use flashone method to unbrick
Click to expand...
Click to collapse
As i already mentioned i cant get into qualcomm recovery so i cant use flashone
try to flash fastboot rom from cucoco's.
Tsoler said:
As i already mentioned i cant get into qualcomm recovery so i cant use flashone
Click to expand...
Click to collapse
connect phone to computer, try force shutdown phone by hard button, ater phone shutdown, immediately release power but keep both volume. Phone maybe will enter Qualcomm flash dead mode, and Flashone will regconize com phone (refresh nedded)
Hope you success ! And believe, if a phone can flash with Qfil or Flashone, almost that phone never die (software)
Are you able to connect to the phone via Vysor, either via Chrome browser or as a standalone app on Windows PC when you do not see anything on the phone screen? Please post if Vysor install goes thru successfully. Hope your developer options/USB debugging are on. I assume your phone boots but may have display issues either hw or sw.
md07 said:
connect phone to computer, try force shutdown phone by hard button, ater phone shutdown, immediately release power but keep both volume. Phone maybe will enter Qualcomm flash dead mode, and Flashone will regconize com phone (refresh nedded)
Hope you success ! And believe, if a phone can flash with Qfil or Flashone, almost that phone never die (software)
Click to expand...
Click to collapse
Did what you said but nothing happens
kayyappan said:
Are you able to connect to the phone via Vysor, either via Chrome browser or as a standalone app on Windows PC when the you do not see anything on the phone screen? Please post if Vysor install goes thru successfully. Hope your developer options/USB debugging are on. I assume your phone boots but may have display issues either hw or sw.
Click to expand...
Click to collapse
Phone gets recognized but not long enough to do anything (windows makes sound but doesn't install anything and doesn't show up in device manager)
try this guide
https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/
You have mentioned that you are able to see the device in recovery and fastboot till you release the buttons - does this mean if the buttons are held say in fastboot mode you are able to see the device via "fastboot devices" or in recovery the twrp screen or nothing ever shows up at all? Are the buttons clicking properly? Check individually to make sure - particularly the power button. Does it vibrate at any point of time when you press and hold the power button? Are you able to see any backlight when you say the screen is on?
If there no backlight shine a torch or sunlight from the side of the screen to see anything at all on the screen.
Vysor reports apk not installed when it attempts to download from PC to phone but fails. With Vysor you will have two windows one showing status of phone - this is the main window. The other is the mirrored one - that of the phone when you click view on the main window. I forgot that the phone requires approval to install the apk. Please see the attached thumbnails. Keep touching the screen about 3 cms up from the bottom of the screen (not the phone) to see any change. Hope your touch works.
I know it is quite frustrating to try a number of things. I recently went thru the same on Galaxy S4 to make sure the phone but for the screen works OK prior to ordering the screen. Besides in my case developer options was disabled and touch also did not work. It took about a week of learning and trying to see something on Vysor. I never have used a Sam phone till that time this broken phone was handed over to me.
After a lot of trying i found out that when i keep pressed power + vol down or vol up while connected to pc and device is off it gets recognized as
qualcomm hs-usb qdloader 9008 long as i keep the keys pressed so i tried the flashone method but it just says could not connect
Are Qualcomm drivers loaded on your computer? I have not used flashone. I used QPST to see if phone is connected. I am not sure if they are same.
kayyappan said:
You have mentioned that you are able to see the device in recovery and fastboot till you release the buttons - does this mean if the buttons are held say in fastboot mode you are able to see the device via "fastboot devices" or in recovery the twrp screen or nothing ever shows up at all? Are the buttons clicking properly? Check individually to make sure - particularly the power button. Does it vibrate at any point of time when you press and hold the power button? Are you able to see any backlight when you say the screen is on?
If there no backlight shine a torch or sunlight from the side of the screen to see anything at all on the screen.
Vysor reports apk not installed when it attempts to download from PC to phone but fails. With Vysor you will have two windows one showing status of phone - this is the main window. The other is the mirrored one - that of the phone when you click view on the main window. I forgot that the phone requires approval to install the apk. Please see the attached thumbnails. Keep touching the screen about 3 cms up from the bottom of the screen (not the phone) to see any change. Hope your touch works.
I know it is quite frustrating to try a number of things. I recently went thru the same on Galaxy S4 to make sure the phone but for the screen works OK prior to ordering the screen. Besides in my case developer options was disabled and touch also did not work. It took about a week of learning and trying to see something on Vysor. I never have used a Sam phone till that time this broken phone was handed over to me.
Click to expand...
Click to collapse
It doesn't stay long enough in recovery or fastboot to do anything it shuts off after a few seconds even with the buttons pressed after that it just shows a black screen
Phone vibrates when i press power and shows leeco logo (not os logo) and after 1-2 seconds screen goes black and phone vibrates again and shows leeco logo again and just continues looping
if i try to press power + vol up normally it goes into recovery but as soon as recovery is loaded screen goes black (screen on just doesn't show anything) the same goes for fastboot if i press power + vol down it loads fastboot but after 1-2 seconds screen goes black
if i keep pressing keys the phone just stays longer in recovery/fastboot but only 4-5 seconds
I assume you have adb and fastboot. Since you say the screen remains on when booting to recovery open a command prompt at the directory where adb is and issue a command "adb devices" without quotes. Does it just exit without showing any device or throws up some error? Try this irrespective of the black screen.
Have you looked at and tried what is given by @HTC-TYTN2 at post #8? It is for Le Max 2 and you will find a link to Quallcomm drivers too. Do not bother that the link mentions X820 even your Max 2 is 821, 829, etc.
since it happened after charging, you might want to check your cable and battery. best is to get a cheap usb multimeter.
Gesendet von meinem LEX820 mit Tapatalk
I too thought it could be the battery based on that's the screen goes off. But he also mentioned that the screen remains on but nothing to be seen after a short while. Wanted to suggest slow speed charging probably via a laptop usb as I'm not sure if he used high speed charging resulting in battery issue.
Did you solve the problem?
My phone just died completely! No response at all anymore. I'm contacting the seller now to send the phone back.
Looks like it is a hardware defect! A pretty odd one but nothing i can do anymore. I send it back and post what the problem is as soon as get any information.
Thanks to everyone who tried to help!
Tsoler said:
My phone just died completely! No response at all anymore. I'm contacting the seller now to send the phone back.
Looks like it is a hardware defect! A pretty odd one but nothing i can do anymore. I send it back and post what the problem is as soon as get any information.
Thanks to everyone who tried to help!
Click to expand...
Click to collapse
Try this:
https://www.androidfilehost.com/?w=files&flid=136823
download file, unzip, open folder, connect phone to USB via fastboot ( phone off phone + hold volume -) . Click to the flash app in your PC. The app should find the phone. Confirm TWRP problem -NO and start flash.
Drivers must be installed.
Drivers here.
https://uloz.to/!A6B4AmEVx87S/adbdriverinstaller-exe
I can, pass the cuoco rom by qfil? Another type of flash, because I can not access recovery and twrp ?, only by fastboot
RaphaBraga23 said:
I can, pass the cuoco rom by qfil? Another type of flash, because I can not access recovery and twrp , only by fastboot
Click to expand...
Click to collapse
Try this via fastboot mode.:
https://www.androidfilehost.com/?w=files&flid=136823
download file, unzip, open folder, connect phone to USB via fastboot ( phone off phone + hold volume -) . Click to the flash app in your PC. The app should find the phone. Confirm TWRP problem -NO and start flash.
Drivers must be installed.
Drivers here.
https://uloz.to/!A6B4AmEVx87S/adbdriverinstaller-exe
hi everyone happy new year
pleaaaaaase i need your help. i flashed my lg ls992 rom, but when the flash ends, normally the device rebooting but my device is going off and still of, i press power button but it's still of, trying to enter to recovery mode it's the same, connect the phone to charge but nothing change it stills off and don't charge, but when i connect it to pc , it's recognized the mobile driver but the charging signal don't appears.
i tried several thing like inplug the batterie and press 30 seconds on power button.. but nothing new, no flash program recognized my device
please help me 3 days of trying and trying but not result
medja77 said:
hi everyone happy new year recognized the mobile driver but the charging signal don't appears.
i tried several thing like inplug the batterie and press 30 seconds on power button.. but nothing new, no flash program recognized my device
please help me 3 days of trying and trying but not result
Click to expand...
Click to collapse
Uninstall all drivers use USB DEVIEW to uninstall hidden drivers and do this
https://www.youtube.com/watch?v=dMzEcyVwQiM
Hello guys, i have sony xz1 g431, i bricked my phone when i try to install another rom of another device via twrp. Now my phone no light when connect to pc, no light when charging, flash tool doesnt recognize my phone. When i connect my phone to pc it only shows QUSB_BULK on my pc. I think it lost fastboot or something. I try hold down button, up button or both when connect to pc but still no light and nothing happen.
Please help me fix this problem or atleast some good suggestions to solve this problem. I will really happy for that. Thanks :crying:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
j4nn said:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
Click to expand...
Click to collapse
i have tried it but there's no light. I think it's dead :crying:
@Karl Einstein, have you tried both ways as suggested above?
Maybe you can examine what usb device appear (if any) in each of the described modes (tried to enter flash mode, tried to enter fastboot mode, tried to just plug the phone to usb without holding any button from power off state).
What happens if you try to enter recovery mode (twrp) - having your phone powered off, without usb connection, holding volume down and power, should enter twrp if you had it flashed before.
Do you get any vibration when hold the power button and.volume.key.up?
Karl Einstein said:
Hello guys, i have sony xz1 g431, i bricked my phone when i try to install another rom of another device via twrp. Now my phone no light when connect to pc, no light when charging, flash tool doesnt recognize my phone. When i connect my phone to pc it only shows QUSB_BULK on my pc. I think it lost fastboot or something. I try hold down button, up button or both when connect to pc but still no light and nothing happen.
Please help me fix this problem or atleast some good suggestions to solve this problem. I will really happy for that. Thanks :crying:
Click to expand...
Click to collapse
Well...I think your phone is dead...I'm really sorry to say that, but in this case, that is the only reasonable explanation.
Yesterday I flashed the GSI image, then tried to flash to eXistenZ, it just stuck in the startup interface. However, it can still enter flash mode and fastboot mode, I have no choice but to use the newflasher to re-flash the firmware, it will return to normal.
In general, Sony devices are hard to change bricks, unless the phone is a Japanese carrier's custom phone (generally can not unlock the bootloader, and can only flash some firmware).
I have seen users who have flashed CE firmware for the docomo version and then can't enter flash mode and fastboot mode.Unlike your device,her phone is totally dead...It can't be charged, and there is no prompt to connect to the computer.
If you can buy a motherboard from eBay or somewhere else,you can disassemble your phone,then replace the old motherboard.
Hope these helps.
Thank you guys for all your support. Finally i decided to skip this problem and i will buy a new device
TimCrownie said:
Well...I think your phone is dead...I'm really sorry to say that, but in this case, that is the only reasonable explanation.
Yesterday I flashed the GSI image, then tried to flash to eXistenZ, it just stuck in the startup interface. However, it can still enter flash mode and fastboot mode, I have no choice but to use the newflasher to re-flash the firmware, it will return to normal.
In general, Sony devices are hard to change bricks, unless the phone is a Japanese carrier's custom phone (generally can not unlock the bootloader, and can only flash some firmware).
I have seen users who have flashed CE firmware for the docomo version and then can't enter flash mode and fastboot mode.Unlike your device,her phone is totally dead...It can't be charged, and there is no prompt to connect to the computer.
If you can buy a motherboard from eBay or somewhere else,you can disassemble your phone,then replace the old motherboard.
Hope these helps.
Click to expand...
Click to collapse
Just a side note , why flash existenz on a gsi rom... As it is made for stock Sony only or did I just misread something..
I had the same issue before on my lenovo p2 it lost fastboot and download mode but the PC detect it as qusb bulk then Qualcomm USB h9008 I searched all solutions but no good I think it needs some kind of box to push the modes or change the mother board. So I changed to Sony instead of repair it
Karl Einstein said:
Thank you guys for all your support. Finally i decided to skip this problem and i will buy a new device
Click to expand...
Click to collapse
Sad to ear that...
I had the same issue with my previous Htc10.
As it was still under warranty, I have had to contact HTC support and told them that and OTA bricked it.
They accepted the issue and replaced the motherboard.
I was BL unlocked, rooted and custom rom when it happened and no issue with support as they had no mean to prove it ?.
If still under warranty try to contact Sony support and tell them the same story... Ota bricks my phone ?
lilbrat said:
Just a side note , why flash existenz on a gsi rom... As it is made for stock Sony only or did I just misread something..
Click to expand...
Click to collapse
I've flashed eXistenZ before flash GSI in my phone. I thought GSI image would cover my origin ROM like eXistenZ, so after flash GSI image in,I flash eXistenZ again.
j4nn said:
Just have the phone powered off, hold just only the volume down button and while holding it, connect the phone to usb cable to your PC.
It should enter flash mode (green light), where you can flash stock firmware via newflasher (or possibly also via flashtool, but I do not use that).
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
If any of those modes are available, the phone should be possible to recover.
Click to expand...
Click to collapse
I have the same issue. My sony xperia xz1 G8342 got sudden dead. (Before dead, I remember I disabled "Developer Mode"). Now its not response by any mean except charging sign when i connect to Power source or PC. Xperia Flashtool shows "device connected with USB debugging disabled".
So, How Can I enter flash mode or fastboot mode? Is My phone recoverable? Please Help.
Thanks
Yesterday I was struggling with my XZ1 Compact and came across this thread that gave me some light to get my mobile phone back.
I guess it's way late for Karl now but just in case, I'm sharing my experience. I was working on my device to get LineageOS 18, as I'm a total newbie with roms I followed the different articles that were posted on Getdroidtips for this particular case: Unlocked bootloader, flashed TRWP and installled lineageos. But then I realized it would be good to have Google Play for restoring my files and apps, but when tried to reboot into recovery mode to get Gapps flashed, Black Screen Of Death started.
After that
with the phone plugged to the pc it wasn't recognized as a device (so adb or fasboot where useless)
the only thing the phone reacted to was to press and hold power + volume up (either for reset or power off)
but no matter what, next boot again BSoD
Tried the Xperia Companion but it prompted that repair was not possible as bootloader was unlocked.
Eventually found this life saver
j4nn said:
If you have the phone off, hold volume up button while connecting to usb, it should enter fastboot (blue light), which also may be used for some recovery, if the phone has been unlocked (or for the unlock itself).
Click to expand...
Click to collapse
From there, using fasboot I could reboot the device back with the LineageOS. I was still having issues with recovery boot but I'll post that on a different thread.
Thanks again to everyone for sharing thoughts and tips!