Related
this mod is the best for ginger bread
i tried and using this
its not my mod
its developed by redstriker
original thread-http://forum.xda-developers.com/showthread.php?t=2296428
hit thanks if helped
Requirement:
1) Rooted device!
2)CWM for flashing rwoksome engine!
3)Root explorer!!
NOTE:BEFORE DOING ANYTHING YOU MUST HAVE A BACKUP OF YOUR SYSTEM!
Also,if you are using any custom mod please REMOVE it,beacuse there are chances of getting bootloop!!
Procedure:
1) Download the RWOKSOME ENGINE 2 from here
http://www.mediafire.com/?4bo9aovh99727yo
2) Flash this zip through CWM.
3) Now download VIPER!
link:http://www.mediafire.com/?pkbdfsii7ikn26l
4) Extract the correct folder according to your Android version. (Android 2.3 or Android 4.X)
5)Copy all the files inside that folder to your SD Card.
6) Use any Explorer with root access,copy libv4a_xhifi_xx.so(2.3 is gb,4.X is ics) to /system/lib/soundfx/ ,set permission to rw-r-r.
7) Now install ViPER4Android_XHiFi.apk
8) Reboot!
9)Open VIPER.apk>> Enable viper engine,Set your own parameters and ENJOY!!!!!!
I read the OP of A.R.I.S.E. several times, and honestly, I didn't understand it properly. And plus, I have also seen a lot of Onyx users reporting that the installation freezes in recovery. Can someone please guide me through the entire process? Thanks in advance!
meraj99 said:
I read the OP of A.R.I.S.E. several times, and honestly, I didn't understand it properly. And plus, I have also seen a lot of Onyx users reporting that the installation freezes in recovery. Can someone please guide me through the entire process? Thanks in advance!
Click to expand...
Click to collapse
I hope you are aware of flashing custom recovery and rooting your phone. Once you did that it is easy to install it.
1. Download arise from official thread. (am using magnum opus version) Make sure you download non auroma version.
2. For starters inside zip there will be a folder called our modules. Copy any of the arise_customize.prop file from that and paste it in in internal storage root directory.
3. flash the ARISE zip from recovery and you are good to go.
4. Read arise_customize.prop file for further info of adding and removing modules.
micoeyes said:
I hope you are aware of flashing custom recovery and rooting your phone. Once you did that it is easy to install it.
1. Download arise from official thread. (am using magnum opus version) Make sure you download non auroma version.
2. For starters inside zip there will be a folder called our modules. Copy any of the arise_customize.prop file from that and paste it in in internal storage root directory.
3. flash the ARISE zip from recovery and you are good to go.
4. Read arise_customize.prop file for further info of adding and removing modules.
Click to expand...
Click to collapse
which effect do you prefer?
meraj99 said:
which effect do you prefer?
Click to expand...
Click to collapse
I prefer Dolby Atmos with Dirac. Viper with ground zero preset (with my customization) nothing else. For speaker mode I use Atmos with movie preset no Viper n Dirac.
Hi,
Here I have Viper4android the best equalizer o ever used and guide to install...
1: Download zip file below added below Link
2: Root your device as described in my Root for 7.0 same as 8.0 as describes in my last thread.
3: Place zip file internal storage
4: go to Custom Recovery I.e. TWRP
5: Install zip file, press Reboot System
6: install root explorer, go to directory "system/vendor/etc"
7: you will see file named "audio_effects.conf"
8: Rename file as "audio_effects.conf.back"
9: Now go to installed apps and open Viper4android, it will ask to install driver, click yes...
10: After some time it will say reboot...
11: Now Reboot and enjoy
I have tested at custom/stock Nougat ROM for moto x2 and working, sound is Awsome... I always missed good equalizer in new ROMS and here you go....
Have a nice day
File attached below.
Note: Be patient while installing driver if shows close or wait for app press wait until it shows reboot!! Enjoy
https://mega.nz/#!MmQlAIZI!gy21yMqT6bN0aigs_ybyUN3PisNwolKVwN4RRRVwEOw
Don't forget to hit Thanks if you like this
In nougat, you just have to install viperFX v6.1 and that's it, it works without needing to install a driver or modify anything.
You just have to consider having Selinux in permissive mode. regards
It also works together with dolby
Casper1982 said:
In nougat, you just have to install viperFX v6.1 and that's it, it works without needing to install a driver or modify anything.
You just have to consider having Selinux in permissive mode. regards
It also works together with dolby
Click to expand...
Click to collapse
Ok I'll try it
Instructions to Install ViPER4Android on Android Oreo
The instructions have been split into two parts for your convenience. The first part involves setting up the device before you proceed to the actual instructions to install ViPER4Android on Android Oreo 8.0. The second part covers installing ViPER4Android itself and the drivers.
Step 1: Pre-setup
Download and install Busybox on your rooted Android. V4A team recommend using Stephen (Stericson) Busybox, so download it by clicking on the app box below.
BusyBox
Stephen (Stericson) Tools FreeDownload
Once it has been installed on your device, launch the app from the app drawer.
As soon as the app starts, it will prompt you for root permissions, so grant them.
Install ViPER4Android on Android Oreo - Busybox Installation
Install ViPER4Android on Android Oreo – Busybox Installation
Make sure that you are in the “Install Busybox” tab. Do not modify any options, leave them as they are.
Tap on the “Install” button on the very bottom of the app screen. The Busybox installation will start and complete in no time. You shall see the confirmation message instantly.
Next, download a root-enabled file manager of your choice. We prefer Solid Explorer for its simplicity and efficiency.
Solid Explorer File Manager
NeatBytes Productivity FreeDownload
Once installed, launch Solid Explorer.
Swipe out from the left edge of the app screen and tap on “Root” under the “Storages” menu.
Install ViPER4Android on Android Oreo - Give Root permissions to Solid Explorer
Install ViPER4Android on Android Oreo – Give Root permissions to Solid Explorer
The app will prompt for root permissions, grant them.
Navigate to /Vendor/etc. Find the file named “audio_effects.conf”.
Long-press on the file, then tap on the 3-dot overflow menu on the top-right and select “Rename”.
Change the filename to “audio_effects.conf.bak“. You could have simply deleted the file, but we advise you to rename it so that if you want to restore in future, it will spare you some trouble.
Install ViPER4Android on Android Oreo - Rename "audio_effects.conf" file in /vendor/etc
Install ViPER4Android on Android Oreo – Rename “audio_effects.conf” file in /vendor/etc
Just tap on “OK” and exit the Solid Explorer.
Finally, the last thing to do is set SELinux status as Permissive. We can do that easily using “The SELinux Switch” app. So, download the app and install it on your device – The.SELinux.Switch.ver.6.0.3.build.603.apk. Then launch the app, grant it root permissions, and press the “Permissive” button. If you find it troublesome, you can simply follow our tutorial.
Just reboot your device. It is very important to reboot after you have performed the above.
Step 2: Install ViPER4Android on Android Oreo
Now that you have properly setup your Android device to install ViPER4Android on Android Oreo, follow the steps below.
Download ViPER4Android for Android Oreo: ViPER4Android_FX_v2505.zip
Extract the downloaded file. You shall then have two files:
ViPER4Android_FX_v2505_A4.x-A7.x.apk
ViPER4Android_FX_v2505_A7.x_Nougat_IO_test_fix.apk
We are only going to need the latter (ViPER4Android_FX_v2505_A7.x_Nougat_IO_test_fix.apk).
Connect your device to the PC and transfer the file to it.
Install ViPER4Android on Android Oreo - Install ViPER4Android app
Install ViPER4Android on Android Oreo – Install ViPER4Android app
Now open Solid Explorer (Or any other file explorer). Navigate to the location where you placed the *.apk file and install it.
Once installed, go to the app drawer and tap on “ViPER4Android”.
As soon as the app is launched, it will prompt you for driver installation.
Just tap on “YES”. You shall instantly be asked for root permissions, so grant them.
Install ViPER4Android on Android Oreo - Driver Installation
Install ViPER4Android on Android Oreo – Driver Installation
The driver installation will begin and your phone’s screen will freeze. Don’t worry, it’s going as planned. Do not exit the app or press any buttons.
After 30-60 seconds the process will complete. Simply tap on “OK” and reboot your device.
Once your phone has rebooted, open the V4A app again and swipe out from the left to open the menu.
Install ViPER4Android on Android Oreo - Driver Status
Install ViPER4Android on Android Oreo – Driver Status
Select “Driver Status”. It should display the status value as “Normal”. You are now ready to give a nice push to your phone’s audio experience by customizing settings in the ViPER4Android app.
I just installed the magisk module and works perfect [emoji848] View attachment 4427228
Enviado desde mi SM-G955F mediante Tapatalk
markoelprototipo said:
I just installed the magisk module and works perfect [emoji848] View attachment 4427228
Enviado desde mi SM-G955F mediante Tapatalk
Click to expand...
Click to collapse
If you listen carefully you will notice that with the Magisk module you do not get changes when you activate the different configurations. And instead with this method everything is working in the best way. Thank you for your comments!
adriano222 said:
If you listen carefully you will notice that with the Magisk module you do not get changes when you activate the different configurations. And instead with this method everything is working in the best way. Thank you for your comments!
Click to expand...
Click to collapse
I tested all configurations and works perfect
markoelprototipo said:
I tested all configurations and works perfect
Click to expand...
Click to collapse
Well in that case remains as an alternative for those who do not work well the other method. Regards!:bueno::RE
viperfx for s7 edge oreo rom
adriano222 said:
Instructions to Install ViPER4Android on Android Oreo
The instructions have been split into two parts for your convenience. The first part involves setting up the device before you proceed to the actual instructions to install ViPER4Android on Android Oreo 8.0. The second part covers installing ViPER4Android itself and the drivers.
Step 1: Pre-setup
Download and install Busybox on your rooted Android. V4A team recommend using Stephen (Stericson) Busybox, so download it by clicking on the app box below.
BusyBox
Stephen (Stericson) Tools FreeDownload
Once it has been installed on your device, launch the app from the app drawer.
As soon as the app starts, it will prompt you for root permissions, so grant them.
Install ViPER4Android on Android Oreo - Busybox Installation
Install ViPER4Android on Android Oreo – Busybox Installation
Make sure that you are in the “Install Busybox” tab. Do not modify any options, leave them as they are.
Tap on the “Install” button on the very bottom of the app screen. The Busybox installation will start and complete in no time. You shall see the confirmation message instantly.
Next, download a root-enabled file manager of your choice. We prefer Solid Explorer for its simplicity and efficiency.
Solid Explorer File Manager
NeatBytes Productivity FreeDownload
Once installed, launch Solid Explorer.
Swipe out from the left edge of the app screen and tap on “Root” under the “Storages” menu.
Install ViPER4Android on Android Oreo - Give Root permissions to Solid Explorer
Install ViPER4Android on Android Oreo – Give Root permissions to Solid Explorer
The app will prompt for root permissions, grant them.
Navigate to /Vendor/etc. Find the file named “audio_effects.conf”.
Long-press on the file, then tap on the 3-dot overflow menu on the top-right and select “Rename”.
Change the filename to “audio_effects.conf.bak“. You could have simply deleted the file, but we advise you to rename it so that if you want to restore in future, it will spare you some trouble.
Install ViPER4Android on Android Oreo - Rename "audio_effects.conf" file in /vendor/etc
Install ViPER4Android on Android Oreo – Rename “audio_effects.conf” file in /vendor/etc
Just tap on “OK” and exit the Solid Explorer.
Finally, the last thing to do is set SELinux status as Permissive. We can do that easily using “The SELinux Switch” app. So, download the app and install it on your device – The.SELinux.Switch.ver.6.0.3.build.603.apk. Then launch the app, grant it root permissions, and press the “Permissive” button. If you find it troublesome, you can simply follow our tutorial.
Just reboot your device. It is very important to reboot after you have performed the above.
Step 2: Install ViPER4Android on Android Oreo
Now that you have properly setup your Android device to install ViPER4Android on Android Oreo, follow the steps below.
Download ViPER4Android for Android Oreo: ViPER4Android_FX_v2505.zip
Extract the downloaded file. You shall then have two files:
ViPER4Android_FX_v2505_A4.x-A7.x.apk
ViPER4Android_FX_v2505_A7.x_Nougat_IO_test_fix.apk
We are only going to need the latter (ViPER4Android_FX_v2505_A7.x_Nougat_IO_test_fix.apk).
Connect your device to the PC and transfer the file to it.
Install ViPER4Android on Android Oreo - Install ViPER4Android app
Install ViPER4Android on Android Oreo – Install ViPER4Android app
Now open Solid Explorer (Or any other file explorer). Navigate to the location where you placed the *.apk file and install it.
Once installed, go to the app drawer and tap on “ViPER4Android”.
As soon as the app is launched, it will prompt you for driver installation.
Just tap on “YES”. You shall instantly be asked for root permissions, so grant them.
Install ViPER4Android on Android Oreo - Driver Installation
Install ViPER4Android on Android Oreo – Driver Installation
The driver installation will begin and your phone’s screen will freeze. Don’t worry, it’s going as planned. Do not exit the app or press any buttons.
After 30-60 seconds the process will complete. Simply tap on “OK” and reboot your device.
Once your phone has rebooted, open the V4A app again and swipe out from the left to open the menu.
Install ViPER4Android on Android Oreo - Driver Status
Install ViPER4Android on Android Oreo – Driver Status
Select “Driver Status”. It should display the status value as “Normal”. You are now ready to give a nice push to your phone’s audio experience by customizing settings in the ViPER4Android app.
Click to expand...
Click to collapse
Hello, sir im trying to install viper4android on samsung s7 edge G935FD im using oreo 8.0 (samsung experience 9) offical vietnam rom i got this rom from this website.
i did same as you told to do to install viperfx but the problem is there is no file named as ''audio_effect.conf'' in root/Vendor/etc
in root/vendor/etc there is a file named as audio_effects_common.conf.
and if i go to root/system/etc there i can see these two files ''audio_effects.conf'' and ''audio_effects_sec.conf''
and as you said to rename ''audio_effects.conf'' as ''audio_effects.conf.bak'' i did this but after doing this when i open viper it says tap yes to install drivers when i tap yes it says ''driver install failed: the busybox installation found on your device doesnot work. this usually means you installed a wrong or broken busybox. V4A needs stericson's busybox to work.if you are sure you installed the proper busybox,then please confirm your device has been completely rooted.''
and my root is fine and even busybox is installed properly i guess actually error comes when i rename the ''audio_effect.conf'' to ''audio_effect.conf.bak'' and if i rename it back to ''audio_effect.conf'' then it doesnot show me this error but it keeps on asking my to install driver again and again please help me it been more then 18 hours im trying to install viperfx but i cant do it
im a music love i managed to get a good headphone but without viper4android music dont feell that good
No download links dor busybox
---------- Post added at 11:23 PM ---------- Previous post was at 11:20 PM ----------
I can't find download links for busybox
M seeing only audio_effects.xml and audio_policy.conf
Which 1 shld i rename??
Phenomenali'm said:
M seeing only audio_effects.xml and audio_policy.conf
Which 1 shld i rename??
Click to expand...
Click to collapse
This is the friend file!:good:
wasaymirza said:
Hello, sir im trying to install viper4android on samsung s7 edge G935FD im using oreo 8.0 (samsung experience 9) offical vietnam rom i got this rom from this website.
i did same as you told to do to install viperfx but the problem is there is no file named as ''audio_effect.conf'' in root/Vendor/etc
in root/vendor/etc there is a file named as audio_effects_common.conf.
and if i go to root/system/etc there i can see these two files ''audio_effects.conf'' and ''audio_effects_sec.conf''
and as you said to rename ''audio_effects.conf'' as ''audio_effects.conf.bak'' i did this but after doing this when i open viper it says tap yes to install drivers when i tap yes it says ''driver install failed: the busybox installation found on your device doesnot work. this usually means you installed a wrong or broken busybox. V4A needs stericson's busybox to work.if you are sure you installed the proper busybox,then please confirm your device has been completely rooted.''
and my root is fine and even busybox is installed properly i guess actually error comes when i rename the ''audio_effect.conf'' to ''audio_effect.conf.bak'' and if i rename it back to ''audio_effect.conf'' then it doesnot show me this error but it keeps on asking my to install driver again and again please help me it been more then 18 hours im trying to install viperfx but i cant do it
im a music love i managed to get a good headphone but without viper4android music dont feell that good
Click to expand...
Click to collapse
Were you able to find a fix for this? I'm having the same issues, and cannot find a solution. Thanks!
Sagoode said:
Were you able to find a fix for this? I'm having the same issues, and cannot find a solution. Thanks!
Click to expand...
Click to collapse
Same goes here
Enable ARcore and other funky AR apps on stock rom
This little zip enables ARcore for the Asus Max Pro M1 stock rom
Tried and tested successfully on the ZB601KL variant (4/64)
Not tested on custom rom - will probably not work.
What works:
1. Latest ARCore
2. Measure App
3. IKEA app
4. Line draw app
5. AR Stickers modded (see below)
This is based on these two:
https://forum.xda-developers.com/showpost.php?p=76920297&postcount=5176
https://forum.xda-developers.com/showpost.php?p=76580197&postcount=1
Hence thanks to these two gentlemen and full credits to them:
@Arnova8G2
@Stampyron
Steps (reproducing from @Stampyron thread with some modifications) :
Step 1. Download and install ARCore apk from here https://www.apkmirror.com/apk/google-inc/arcore/arcore-1-3-18060406-release/
Step 2. Install an app that use ARCore. If you're lazy, you can use this apk https://www.apkmirror.com/apk/googl...-anywhere-with-ar-2-0-0-android-apk-download/
Step 3. Open the app you installed in step 2 and let it crash. This will make the folders and files that we're going to use later on.
Step 4. Download the file named arcore_x00t.zip
Step 5. Reboot to twrp and and flash the zip file
Step 6. Reboot to system. Now you can use any apps that require ARCore!
NOTE: If you updated ARCore repeat step 3 onwards
ARStickers Updated to ver 1.2.180326103.apk - 4 July 2018
ARStickers doesnt work with the apk from apkmirror.com. Use this modded one instead
https://drive.google.com/open?id=1DqnA2lFV5QYq7vQDah2IMLlAO285nKzK
(thanks to @Arnova8G2)
Explanation
@Arnova8G2 twrp zip is based on placing a file in the /data partition and renaming it as per the ro.build.product value.
However for stock ROM, the true value that works for this device is what is returned by ro.product.device instead in the system (different from the one in twrp), hence the modification is needed
The value in the fully booted stock rom is "ASUS_X00T_2"
And the second modification needed is to make the file name include "8.1" for latest oreo for this device.
Hence the file name now that works for this device in stock ROM is: "device_profile_ASUS_X00T_2_colon_8.1.textproto"
Enjoy!
candiesdoodle said:
Enable ARcore and other funky AR apps
This little zip enables ARcore for the Asus Max Pro M1
Tried and tested successfully on the ZB601KL variant (4/64)
What works:
1. Latest ARCore
2. Measure App
3. IKEA app
4. Line draw app
5. AR Stickers modded (see below)
This is based on these two:
https://forum.xda-developers.com/showpost.php?p=76920297&postcount=5176
https://forum.xda-developers.com/showpost.php?p=76580197&postcount=1
Hence thanks to these two gentlemen and full credits to them:
@Arnova8G2
@Stampyron
Steps (reproducing from @Stampyron thread with some modifications) :
Step 1. Download and install ARCore apk from here https://www.apkmirror.com/apk/google...-apk-download/
Step 2. Install an app that use ARCore. If you're lazy, you can use this apk https://www.apkmirror.com/apk/google...where-with-ar/
Step 3. Open the app you installed in step 2 and let it crash. This will make the folders and files that we're going to use later on.
Step 4. Download the file named arcore_x00t.zip
Step 5. Reboot to twrp and and flash the zip file
Step 6. Reboot to system. Now you can use any apps that require ARCore!
NOTE: If you updated ARCore repeat step 3 onwards
ARStickers
ARStickers doesnt work with the apk from apkmirror.com. Use this modded one instead
https://drive.google.com/open?id=17r5Hg-WyRTRVAkqx40vmSHyrDMAxmKQG
(thanks to @Arnova8G2)
Explanation
@Arnova8G2 twrp zip is based on placing a file in the /data partition and renaming it as per the ro.build.product value.
However the true value that works for this device is what is returned by ro.product.device instead in the system (different from the one in twrp), hence the modification is needed
The value in the fully booted rom is "ASUS_X00T_2"
And the second modification needed is to make the file name include "8.1" for latest oreo for this device.
Hence the file name now that works for this device is: "device_profile_ASUS_X00T_2_colon_8.1.textproto"
Enjoy!
Click to expand...
Click to collapse
Thanks for the work.Can u suggest me some good ar apps as ur links are not working
Bhuvi100 said:
Thanks for the work.Can u suggest me some good ar apps as ur links are not working
Click to expand...
Click to collapse
Links updated. Please try now
I am waiting for magisk module. I don't want to temper system
Aftab_khatri said:
I am waiting for magisk module. I don't want to temper system
Click to expand...
Click to collapse
this is data partition, nothing on system
candiesdoodle said:
Enable ARcore and other funky AR apps on stock rom
This little zip enables ARcore for the Asus Max Pro M1 stock rom
Tried and tested successfully on the ZB601KL variant (4/64)
Not tested on custom rom - will probably not work.
What works:
1. Latest ARCore
2. Measure App
3. IKEA app
4. Line draw app
5. AR Stickers modded (see below)
This is based on these two:
https://forum.xda-developers.com/showpost.php?p=76920297&postcount=5176
https://forum.xda-developers.com/showpost.php?p=76580197&postcount=1
Hence thanks to these two gentlemen and full credits to them:
@Arnova8G2
@Stampyron
Steps (reproducing from @Stampyron thread with some modifications) :
Step 1. Download and install ARCore apk from here https://www.apkmirror.com/apk/google-inc/arcore/arcore-1-3-18060406-release/
Step 2. Install an app that use ARCore. If you're lazy, you can use this apk https://www.apkmirror.com/apk/googl...-anywhere-with-ar-2-0-0-android-apk-download/
Step 3. Open the app you installed in step 2 and let it crash. This will make the folders and files that we're going to use later on.
Step 4. Download the file named arcore_x00t.zip
Step 5. Reboot to twrp and and flash the zip file
Step 6. Reboot to system. Now you can use any apps that require ARCore!
NOTE: If you updated ARCore repeat step 3 onwards
ARStickers
ARStickers doesnt work with the apk from apkmirror.com. Use this modded one instead
https://drive.google.com/open?id=17r5Hg-WyRTRVAkqx40vmSHyrDMAxmKQG
(thanks to @Arnova8G2)
Explanation
@Arnova8G2 twrp zip is based on placing a file in the /data partition and renaming it as per the ro.build.product value.
However for stock ROM, the true value that works for this device is what is returned by ro.product.device instead in the system (different from the one in twrp), hence the modification is needed
The value in the fully booted stock rom is "ASUS_X00T_2"
And the second modification needed is to make the file name include "8.1" for latest oreo for this device.
Hence the file name now that works for this device in stock ROM is: "device_profile_ASUS_X00T_2_colon_8.1.textproto"
Enjoy!
Click to expand...
Click to collapse
Does it require a rooted phone?
Abby 244 said:
Does it require a rooted phone?
Click to expand...
Click to collapse
Yes
candiesdoodle said:
Enable ARcore and other funky AR apps on stock rom
This little zip enables ARcore for the Asus Max Pro M1 stock rom
Tried and tested successfully on the ZB601KL variant (4/64)
Not tested on custom rom - will probably not work.
What works:
1. Latest ARCore
2. Measure App
3. IKEA app
4. Line draw app
5. AR Stickers modded (see below)
This is based on these two:
https://forum.xda-developers.com/showpost.php?p=76920297&postcount=5176
https://forum.xda-developers.com/showpost.php?p=76580197&postcount=1
Hence thanks to these two gentlemen and full credits to them:
@Arnova8G2
@Stampyron
Steps (reproducing from @Stampyron thread with some modifications) :
Step 1. Download and install ARCore apk from here https://www.apkmirror.com/apk/google-inc/arcore/arcore-1-3-18060406-release/
Step 2. Install an app that use ARCore. If you're lazy, you can use this apk https://www.apkmirror.com/apk/googl...-anywhere-with-ar-2-0-0-android-apk-download/
Step 3. Open the app you installed in step 2 and let it crash. This will make the folders and files that we're going to use later on.
Step 4. Download the file named arcore_x00t.zip
Step 5. Reboot to twrp and and flash the zip file
Step 6. Reboot to system. Now you can use any apps that require ARCore!
NOTE: If you updated ARCore repeat step 3 onwards
ARStickers Updated to ver 1.2.180326103.apk - 4 July 2018
ARStickers doesnt work with the apk from apkmirror.com. Use this modded one instead
https://drive.google.com/open?id=1DqnA2lFV5QYq7vQDah2IMLlAO285nKzK
(thanks to @Arnova8G2)
Explanation
@Arnova8G2 twrp zip is based on placing a file in the /data partition and renaming it as per the ro.build.product value.
However for stock ROM, the true value that works for this device is what is returned by ro.product.device instead in the system (different from the one in twrp), hence the modification is needed
The value in the fully booted stock rom is "ASUS_X00T_2"
And the second modification needed is to make the file name include "8.1" for latest oreo for this device.
Hence the file name now that works for this device in stock ROM is: "device_profile_ASUS_X00T_2_colon_8.1.textproto"
Enjoy!
Click to expand...
Click to collapse
This method did not work for me. Ar stickers and draw a line app still force closes
---------- Post added at 06:50 PM ---------- Previous post was at 06:24 PM ----------
When I open draw a line app it says "AR CORE KEEPS ON STOPPING".
In recovery zip file is unable flash as digest file cannot be found.
Abby 244 said:
When I open draw a line app it says "AR CORE KEEPS ON STOPPING".
In recovery zip file is unable flash as digest file cannot be found.
Click to expand...
Click to collapse
I tried and it works just fine
Which twrp are you using.
candiesdoodle said:
I tried and it works just fine
Which twrp are you using.
Click to expand...
Click to collapse
I used an otg hard drive .
I so want this feature.:crying:
---------- Post added at 08:52 PM ---------- Previous post was at 08:04 PM ----------
When we go to the AR CORE app link , it provides with 2 versions of the app.
Though I have tried both and none of it worked for me .
I am on the latest build i.e. 311 .
Can I reset the partitions that are already made ?
I don't want to factory reset.
Please help me .
I am a noob
Can I use internal memory of mobile to flash the zip as I don't have a memory card.
Abby 244 said:
I used an otg hard drive .
I so want this feature.:crying:
---------- Post added at 08:52 PM ---------- Previous post was at 08:04 PM ----------
When we go to the AR CORE app link , it provides with 2 versions of the app.
Though I have tried both and none of it worked for me .
I am on the latest build i.e. 311 .
Can I reset the partitions that are already made ?
I don't want to factory reset.
Please help me .
I am a noob
Can I use internal memory of mobile to flash the zip as I don't have a memory card.
Click to expand...
Click to collapse
Yes
Install apks linked here. Then, Just download the zip to your phone. It will come to your internal memory of the phone - in downloads folder. Check using a file explorer such as "es file explorer" or "solid explorer"
Boot into twrp, and flash this file.
Then reboot the system. Done.
Ps- the two apk for arcore are for different platforms. Our phone is arm64, so download that.
candiesdoodle said:
Yes
Install apks linked here. Then, Just download the zip to your phone. It will come to your internal memory of the phone - in downloads folder. Check using a file explorer such as "es file explorer" or "solid explorer"
Boot into twrp, and flash this file.
Then reboot the system. Done.
Ps- the two apk for arcore are for different platforms. Our phone is arm64, so download that.
Click to expand...
Click to collapse
Did what u said , still problem presists. Moreover in twrp my root memory shows 0mb i.e. nothing.
Abby 244 said:
Did what u said , still problem presists. Moreover in twrp my root memory shows 0mb i.e. nothing.
Click to expand...
Click to collapse
Your phone is encrypted. Move that file to sd card and install
Aftab_khatri said:
Your phone is encrypted. Move that file to sd card and install
Click to expand...
Click to collapse
Using otg I get this
Abby 244 said:
Using otg I get this
Click to expand...
Click to collapse
Dude
your data partition is encrypted, you can't flash the zip.
You gotta do it manually after booting into the Rom:
1. Look in the zip for this file
/arcore_x00t.zip/data/data/com.google.ar.core/files/device_profile_database/device_profile_1_colon_8.textproto
2. Copy it to this location with this name. Use a file explorer with root permission:
/data/data/com.google.ar.core/files/device_profile_database/device_profile_ASUS_X00T_2_colon_8.1.textproto
3. Go to a terminal and do these commands
su
restorecon /data/data/com.google.ar.core/files/device_profile_database/device_profile_ASUS_X00T_2_colon_8.1.textproto
4. Reboot.
candiesdoodle said:
Dude
your data partition is encrypted, you can't flash the zip.
You gotta do it manually after booting into the Rom:
1. Look in the zip for this file
/arcore_x00t.zip/data/data/com.google.ar.core/files/device_profile_database/device_profile_1_colon_8.textproto
2. Copy it to this location with this name. Use a file explorer with root permission:
/data/data/com.google.ar.core/files/device_profile_database/device_profile_ASUS_X00T_2_colon_8.1.textproto
3. Go to a terminal and do these commands
su
restorecon /storage/emulated/0/Download/XDA Forums/arcore_x00t.zip/data/data/com.google.ar.core/files/device_profile_database/device_profile_1_colon_8.textproto
4. Reboot.
Click to expand...
Click to collapse
Can i do this without pc?
I was on step 2 of your above mentioned procedure but there was no file as :device_profile_ASUS_X00T_2_colon_8.1.textproto
Instead there was : device_profile_ASUS_A002_1_colon_7.textproto
Abby 244 said:
Can i do this without pc?
I was on step 2 of your above mentioned procedure but there was no file as :device_profile_ASUS_X00T_2_colon_8.1.textproto
Instead there was : device_profile_ASUS_A002_1_colon_7.textproto
Click to expand...
Click to collapse
You have do it on the phone
And ofcourse there is no file with that name. You have to copy it to that folder with that name. Got it?
candiesdoodle said:
You have do it on the phone
And ofcourse there is no file with that name. You have to copy it to that folder with that name. Got it?
Click to expand...
Click to collapse
Thanks for the quick reply. Just gonna try it .
candiesdoodle said:
You have do it on the phone
And ofcourse there is no file with that name. You have to copy it to that folder with that name. Got it?
Click to expand...
Click to collapse
And this happened.
Abby 244 said:
And this happened.
Click to expand...
Click to collapse
Oh common dude
You gotta type whole command in one go
restorecon /data/....
You are trying to execute the actual file..which is wrong