Related
Hello all,
I have tried many things before asking for help, but nothing worked so far.
Here is the story:
I was on ICS 4.0.4, with default ROM coming from carrier.
I wanted to install CM9.1,
spent countless hours doing all backup and reading tutorial.
Tried finally yesterday and it was stuck doing "wiping data". Left it for 20min+ and nothing.
After restarting it, it is now stuck on the boot logo.
I couldn't enter anymore CWM or stock recovery (up+home+power), but could enter Download mode.
So I tried a couple of things I have read on the forum, like installing Siyah-s2-v5.0.1.tar through Odin 3.04 but I still cannot enter recovery mode.
I've read (too late) about the mmc brick bug (couldn't find anyone speaking about it in any tutorial until I reached this point... nothing on CM wiki or in other tuto... classic!).
I hope I'm not in this case though as I can still go to DL mode, and the phones having the brick bug are completely dead (blank screen or no DL mode), as per http://forum.xda-developers.com/showthread.php?t=1756242
I managed to finally get CWM working only by using GT-I9100_ICS_ClockworkMod-Recovery_5.5.0.4.tar from Odin, then tried to install CM9.1 from SD card but after reboot it is stuck on the blue cyanogenmod animation boot screen and nothing happens.
Tried also to restore from CWM my nandroid backup, but during the restore it seems to hang then restart by itself, and then I'm back to Galaxy S boot logo (the animated one with the big S).
And after this I have lost again access to recovery mode.
I can't go back to stock and I can't install CM... I was not expecting such issues, it all seemed pretty basic on paper.
I'm really stressed and don't know what to do
Flash a stock rom in Odin (download mode), re-root your phone/flash a kernel with CWM, restore your backup ?
Hi,
thanks for answering,
I have tried to locate such a rom, but I'm not sure which one... is there a specific one to try ? could you point me to it please ?
so far I have tried I9100XXLPQ_I9100OXALPQ_I9100XXLPQ_HOME.tar.md5
but no luck
you also say "re-root", at the time I used this method:
[GUIDE] ROOT/UNROOT Stock ICS Firmware without flashing unsecure kernel - xda-developers
http://forum.xda-developers.com/showthread.php?t=1501719
Do I need root to install Siyah kernel from Odin ?
I'm trying one from sammobile... let's hope :/
The bad thing is I had no Yellow triangle at the beginning since I'm stuck in this boot loop or no boot to be precise.
Now that I have tried different things to fix it, it is still not working and I have my flash counter = 10.
I cannot even go back to the shop, is there a way to reset it knowing I cannot even reach the OS, I have only DL mode or CWM...
Use a stock rom for your region/carrier (or any stock rom from any region really), it doesn't really matter as I presume you'll be restoring a backup and/or going back to a custom rom anyway won't you ?
Samfirmware & AndroidFirmwares.net have lots of stock roms.
No, you don't need root to flash an Odin version of Siyah. So yes, you can flash that after you've got stock up & running to root your phone rather than re-rooting your phone by flashing a CFRoot kernel or using another root method. Just make sure the version of Siyah you're going to flash matches up with the stock rom you've got on (I.E if you flash a GB stock rom use GB Siyah, ICS stock = use ICS Siyah, etc, etc).
thank you again, I'm downloading the rom from sammobile matching my carrier,
Would you be so kind to send me a PM with your skype username or anything to "chat" with you ? I'm really worried and I spent all night already trying to fix it with no progress at all
Don't worry about the flash counter. That's the least of your problems while your phone is borked Worry about it when it's fixed. There's nothing you can do about the triangle while your phone is cactus.
When you've got it up & running again, use Triangle Away.
But first things first.
---------- Post added at 04:02 AM ---------- Previous post was at 03:59 AM ----------
You're welcome.
Um, no. Absolutely not. Nothing personal, but if I did that for every person who's asked me for 'hands on' help since I've been here, I'd have spent my time doing nothing else. I don't do 'personal' with people from XDA (which is why I have PM's blocked except for mods).
Besides, you're going to learn much more fixing this yourself. I've given you a stack of information thus far, ball is in your court. Every answer to every question you could possibly ask is on this site. It just sometimes takes a bit of work/reading on your part to find it.
megosu said:
thank you again, I'm downloading the rom from sammobile matching my carrier,
Would you be so kind to send me a PM with your skype username or anything to "chat" with you ? I'm really worried and I spent all night already trying to fix it with no progress at all
Click to expand...
Click to collapse
ok I understand.. it is just I have literally spent more than 8 hours on it and had not make any progress at all (even worse I cannot return it to the shop because of the yellow triangle).
I appreciate your help, it gives me a bit of hope but I'm in a very bad situation and I feel I have read and do so much already with no success at all.
I will try your option of restoring the one from Sammobile, I have tried other before without any luck, maybe this one will do... (5min left to DL it).
thanks again for your support
I know where you're coming from. The first flash I tried when I got my phone in 2011 borked because I was careless, and it took me a bit over a day to get the right info/files/etc to get it fixed. I know it's frustrating/tiring/annoying & you're wondering at the start whether you can even fix it. But as long as you've got download mode 99 times out of 100 you can save it.
And as I said, it's good experience; once you've fixed it, you'll be able to handle anything that comes up in future
Let us know how you go. I'm going to bed shortly, but I'm sure someone else will step up & help if you have any further problems.
You're welcome Happy to point you in the right direction.
I have flashed the rom, the exact same one as I had before everything happened...
if it helps, I flashed it from Odin 3.04 as PDA.
I9100BVLPH_I9100TMULPH_I9100BVLPE_HOME.tar.md5
I'm now back to the Samsung GALAXY S2 GT-I9100 logo and nothing happens.
I cannot use recovery mode,
I can use DL mode (it shows 11 counts and current binary as Samsung official.)
update:
I left the phone on the first logo for about 5min and it moved to the next Samsung Galaxy S2 logo, with the big animated S.
I'm waiting but nothing else is happening.
I'm still desperate to fix it.
One thing which can be relevant, whenever I try to wipe or format /data from CWM, my phone is restarting after a few minutes or is saying it cannot be done.
I can format /cache and /system.
Could it be the root cause ? Any way of fixing it ?
Thank you
update: I cannot mount /data from CWM, it says Error mounting /data!
is it the brick bug ? :|
Easy now....your device is still good.
Those animations should take like 1-2 mins when you flash a rom.
Now, you are completly sure that you are actually flashing the right ROM for your device model?
If so, just keep flashing stock roms until you're up and running again, so you can start from scrap.
I tried, the issue is as soon as I flash a stock rom (through Odin), then I can't get into stock recovery mode anymore, I have to flash GT-I9100_ICS_ClockworkMod-Recovery_5.5.0.4.tar to get back the recovery mode.
I tried to flash several times, I think it is down to the fact I cannot mount or format /data.
Which is why I'm wondering if it is the famous brick bug.
My device is GT-I9100 and I took the stock rom from sammobile:
I9100BVLPH_I9100TMULPH_I9100BVLPE_HOME.tar.md5 which is ICS 4.0.4 (that I had before trying to move to CM9.1 and having all this mess in my hands.)
flash this:
http://www.sammobile.com/2012/11/15/i9100xxlsj-%E2%80%93-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/.
you are on siyah kernel right?
what you wanna do know is to get to whatever rom your flashing, forget about cmw for now.
this also might help:
http://forum.xda-developers.com/showthread.php?t=1457458
So it is not lost yet ? Not the brick bug ?
just to be sure:
you want me to install through Odin: Siyah-s2-v5.0.1-CWM.zip
then going back to DL mode
I flash through Odin: I9100XXLSJ_I9100OXXLS1_OXX.zip (coming from your link).
anything I'm missing (even if it seems obvious, please let me know as I'm maybe missing something important)
?
I still cannot do Factory reset... is it a problem ?
I dunno what kernel you are using, If stock 4.0.4 kernel you should flash siyah first (safe kernel, no brick bug), and then countinue flashing the ROM. Check out the brick bug thread in general SII forum for directions if you want.
BTW, Odin recognizes your phone right? Check it out, you'll get a huge long breath.
BTW 2: you don't have any kies applications running in your pc.....am I right? if so, CLOSE THEM ALL!
I did had stock 4.0.4 kernel when I first tried to follow CM9.1 wiki, and I did a factory reset through CWM... which is why I think I might have bricked it...
I have checked the brick bug thread (too late it seems...) but so far I can't be sure if I'm in this case or not as they say they can't even reach DL mode, and I can.
Odin recognizes my phone, yes, but anything I flash is stuck on the animated logo.
I do not have Kies installed, just installed the drivers.
Hello, I'll try to explain what happened to get where I am now, and explain with details the last errors of my GT-9100.
I had a stock room jelly bean 4.1.2 installed. I had Android encrypted + SDCARD encrypted, and decided to format, but I didn't undo the encryption. As result, after master reseting it, it asked for a password do decrypt (as always asked when I turned the phone on), but it wasn't recognizing my password anymore. So I tried to clean and wipe all possible things, which ended on the device stucking at boot (doing boot loops, not asking for password anymore). I got an error on CW Recovery E: Could not load emmc (sounds like my internal storage is gone)
Later on, I tried to re-install the ROM, but got alot of trouble with windows drivers. Couldn't get any rom installed again. My device was then stuck at start, not even showing the white Samsung Galaxy S II GT9100 screen. After trying a variety of MODEMs, Kernels, I always get stuck on boot.info, zimage (kernel) on ODIN (Both 1.85 and 3.07 versions).
The only thing that has worked so far is changing the bootloader to the stock version. After doing this, my smartphone turns on on Chinese language. The ROM loaded is a jelly bean, but it has no status bar, can't open camera/folder explorer, can't do calls, can't acess internet, doesn't even show the configuration menu. And everything is chinese. BTW Calculator was working lol.
So this is the situation. Has my internal storage been gone forever? Is there a way I can flash without being stuck at boot.info or zImage when trying to flash kernel, both on Odin messages? Or is my phone really bricked? Thansk alot, I'll pay close attention to this.
EDIT: I haven't found after a day of research anyone that did data wipes in an encrypted phone, so this can be a guide for any future similar case.
gerijeb said:
Hello, I'll try to explain what happened to get where I am now, and explain with details the last errors of my GT-9100.
I had a stock room jelly bean 4.1.2 installed. I had Android encrypted + SDCARD encrypted, and decided to format, but I didn't undo the encryption. As result, after master reseting it, it asked for a password do decrypt (as always asked when I turned the phone on), but it wasn't recognizing my password anymore. So I tried to clean and wipe all possible things, which ended on the device stucking at boot (doing boot loops, not asking for password anymore). I got an error on CW Recovery E: Could not load emmc (sounds like my internal storage is gone)
Later on, I tried to re-install the ROM, but got alot of trouble with windows drivers. Couldn't get any rom installed again. My device was then stuck at start, not even showing the white Samsung Galaxy S II GT9100 screen. After trying a variety of MODEMs, Kernels, I always get stuck on boot.info, zimage (kernel) on ODIN (Both 1.85 and 3.07 versions).
The only thing that has worked so far is changing the bootloader to the stock version. After doing this, my smartphone turns on on Chinese language. The ROM loaded is a jelly bean, but it has no status bar, can't open camera/folder explorer, can't do calls, can't acess internet, doesn't even show the configuration menu. And everything is chinese. BTW Calculator was working lol.
So this is the situation. Has my internal storage been gone forever? Is there a way I can flash without being stuck at boot.info or zImage when trying to flash kernel, both on Odin messages? Or is my phone really bricked? Thansk alot, I'll pay close attention to this.
EDIT: I haven't found after a day of research anyone that did data wipes in an encrypted phone, so this can be a guide for any future similar case.
Click to expand...
Click to collapse
Tried installing Android 2.3 stock bootloader / rom ?
jiboncom said:
Tried installing Android 2.3 stock bootloader / rom ?
Click to expand...
Click to collapse
No I haven't. Is there any online link here? I couldn't find it.
Solved
After a day looking for it, I solved my problem
I tried several kernels, roms with almost all odin versions. The best one for gt-I9100 was odin 1.87.
This was the deal: After cleaning the encrypted internal storage, it got corrupted. So one of the first steps to get my phone reacting again to ODIN when installing new ROMs was installing the original GT-9100 .PIT file and re-partitioning (Even with every forum/site telling me I should never do it).
So, if you ever do the same mistake as me, try this:
Install a new kernel, then .PIT original file. Get a proper MODEM file, and finally try flashing your ROM.
I also got alot of problem with my USB cable, which is kinda damaged, so out of 10 plug-ins, only a few would work for ODIN. Try getting a brand new cable.
That's it.
gerijeb said:
After a day looking for it, I solved my problem
I tried several kernels, roms with almost all odin versions. The best one for gt-I9100 was odin 1.87.
This was the deal: After cleaning the encrypted internal storage, it got corrupted. So one of the first steps to get my phone reacting again to ODIN when installing new ROMs was installing the original GT-9100 .PIT file and re-partitioning (Even with every forum/site telling me I should never do it).
So, if you ever do the same mistake as me, try this:
Install a new kernel, then .PIT original file. Get a proper MODEM file, and finally try flashing your ROM.
I also got alot of problem with my USB cable, which is kinda damaged, so out of 10 plug-ins, only a few would work for ODIN. Try getting a brand new cable.
That's it.
Click to expand...
Click to collapse
Add [SOLVED] to the title.
I'm in a bit of a tight situation over here. My mom's phone was having issues, so she wanted me to fix it before I left to visit my grandparents. I found a stock ROM for the phone (GT-i9100 International) and flashed it, but the phone always got stuck on the "Samsung Galaxy SII GT-I9100" boot screen (occasionally it would show the "O2" screen, as it was a ROM for Ireland). I tried a different ROM (can't remember what country it was), and I'm still stuck with the same problem. This time no O2 screen though. I've downloaded my ROMs through sammobile.com and I'm using ODIN v1.83.
The label under the battery reads:
Model: GT-I9100
SSN: -I9100GSMH
What ROM should I use and where can I get it? I found this thread with a link to the ROM for the international version, but Hotfile has been shut down, so I can't download it.
Sorry if I could've found the answer with a few more hours of searching, but I've got less than 24 hours to find a fix and I was hoping that someone else could help me. Thanks a lot!
EDIT: I'm in the U.S., if that matters.
Try AndroidFirmwares.net or Samsung-Updates.com. If it were me in that situation (I.E not my phone), I'd be putting whatever the latest firmware is for the carrier/country.
Any region?
MistahBungle said:
Try AndroidFirmwares.net or Samsung-Updates.com. If it were me in that situation (I.E not my phone), I'd be putting whatever the latest firmware is for the carrier/country.
Click to expand...
Click to collapse
Should any region work to get the phone up and running? I just need to get it back up so that I can root it and flash CM10. Thanks.
Yep absolutely. If your end result is to root the phone & put a custom rom on, use any stock rom you can get your hands on. Though I'd be avoiding 4.0.4, anything other than that should be fine.
MistahBungle said:
Yep absolutely. If your end result is to root the phone & put a custom rom on, use any stock rom you can get your hands on. Though I'd be avoiding 4.0.4, anything other than that should be fine.
Click to expand...
Click to collapse
Is 4.1.2 OK, or should I go for 4.0.3 or below?
Doesn't matter, take your pick.
More info on problem
I tried installing two other ROMs (from androidfirmwares.net), one 4.1.2 and one 2.3.6. The 4.1.2 didn't get me anywhere, but after I flashed 2.3.6 the phone said the assert check failed. GT-i9100 is on the list of what it checked for. (I've never had any luck with the assert checks on any of my Samsung phones: GS Captivate, GSII Skyrocket, or AT&T GSIII. I've always had to remove the check in my update script.) I attached a picture.
EDIT: Since the attachment doesn't seem to be working, here's a Dropbox link.
Pic won't load for me, but it mentions 'recovery error', what exactly are you doing/what's the problem ?
MistahBungle said:
Pic won't load for me, but it mentions 'recovery error', what exactly are you doing/what's the problem ?
Click to expand...
Click to collapse
My process:
Open ODIN v3.09
Plug in the phone, already in download mode.
Click the AP button and load my .tar.md5.
Click Start.
Wait for it to finish, leaving the phone untouched on the table.
I just tried another USB cable, but to no avail. I've also tried unplugging the phone right after it reboots and ODIN says "PASS!", but no luck there either. I just tried another ROM that just finished downloading and it's giving me a similar getprop() error. At the bottom of the output in red it says:
E:Error in /cache/recovery/sec_csc.zip
(Status 7)
Installation aborted.
I don't think there's any way for me to edit the update script, as the tar contains a bunch of filesystem images. Even if it was easy to edit it would ruin the checksum verification.
Check out the picture on Dropbox here.
What are you trying to do in Android recovery ? Given what your stated aim is - get a stock rom on the phone, re-root it, put custom rom on, you shouldn't be using Android (I.E stock) recovery at any stage.
The process should be:-
*Flash stock rom with Odin in download mode (I.E phone off - home/vol down/power, not home/vol up/power)
*Root phone with whatever method
*Flash custom rom with CWRecovery, which you'll get once you root the phone
So....You need to go step by step. Start with flashing the stock rom with Odin, and try to boot the phone normally/make sure that was successful before doing the next two steps. Look for Hopper8's 'Odin troubleshooting' guide if you're having trouble getting a successful Odin flash.
Once you've done that, root the phone & make sure you have CWRecovery working, then flash the custom rom.
The phone boots to the recovery screen after it finishes flashing with ODIN. I put it into download mode, run ODIN, and then it that error screen comes up on the next reboot.
Try flashing the three part firmware linked to in Hopper's thread first (this will wipe the phone). I can't help but think we're missing some info re: what's been done to the phone previously here if the phone is booting into recovery mode after being Odin flashed. It shouldn't do that. After an Odin flash/pass the phone should boot normally, assuming it's not a case of the NAND being corrupted (it probably wouldn't boot into recovery if that was the case/you'd be left with constant bootloop)
I know you've mentioned what's on the sticker on the phone chassis under the battery but are you absolutely 100% sure it's an I9100 ?
MistahBungle said:
I know you've mentioned what's on the sticker on the phone chassis under the battery but are you absolutely 100% sure it's an I9100 ?
Click to expand...
Click to collapse
At the top of the download mode screen it says "PRODUCT NAME: GT-i9100". I don't know any other way to tell besides this and the sticker on the back. There are no carrier markings anywhere, and this phone was purchased because it had an FM radio, which only the international version had.
And assuming by "Hopper's thread" you mean this one, I can't because the files are no longer available.
In that case, you're stuck with the other suggestions to try in his thread & continuing to flash stock roms until you get a properly successful flash I.E phone boots/works normally. There might be something really obvious here being missed, but because we're not there with you/don't have the phone in front of us it might be difficult to work out.
It's working!
Yay, I got it to work! I flashed a custom kernel (jeboo), which allowed me to get into CWM. From there I sideloaded CM10 and now it's up and running! Only I still have a problem with internal storage... (That was the problem I was trying to fix originally.) Would the next thing to try to fix that be flashing a PIT file? If so, any tips for doing that?
I'm going to put off trying to fix that problem and do it when I get back. For now it works as a phone, and that's what's most important to her anyway. Thanks for your help MistahBungle.
Solved!
For anyone else who comes across this thread, I was able to solve my problem permanently by flashing a new PIT file. I found the correct PIT files for the GT-i9100 in this XDA thread. It seemed my partitions had become messed up long ago, as the phone had been showing a 2GB /data partition and only a 2GB internal SD card partition (which should've been closer to 12GB) for some time.
I choose a 4GB data partition (since I was running low on /data space last time). Oddly enough, booting the stock ROM after flashing the PIT only showed a 2GB data partition. Once I flashed CM10 it showed as 4GB though.
So, to start off, I messed up big time...
I'll give you the short version, but try to provide as much info as possible. I switched roms a few times in the last few days, going from Trents 8, to the newest Dirty Unicorns, to Trents 10 (where I started having issues) back to DU. I was trying to figure out where the issues came from, and came across someone saying that going from a touchwiz based rom, off of it, and back on, can cause problems. I then read that one of the best ways to fix this was to flash stock firmware and reflash new roms. I tried doing this...
Little did I know, it was a HUGE mistake for me to flash the 4.3 firmware through odin, and when the phone restarted, the "Galaxy Note II" page just kept flashing on and off for a few minutes. I think tried flashing older firmwares, with pit file, but I kept getting errors when I restarted saying that I didn't have Verizon Authorized Software.
Sooo this is where I'm stuck right now. I can't boot the phone at all, and when I try to flash the root66 firmware (the one that's supposed to fix everything?) I still get this verizon unauthorized page. It seems from what I've read that the bootloader relocked because of my 4.3 flash, and I can't find any info on how to unlock that. Anyone have suggestions? I'd really appreciate it!
Update: I retried the 4.3 firmware, and right now "Android is upgrading..." so I'm assuming this means my bootloader is locked, I've lost root, and all that jazz right? From what I've read so far there isn't any way to unlock the bootloader again, am I right? If so, can you point me in the right direction? Much appreciated!
xanderharris86 said:
So, to start off, I messed up big time...
I'll give you the short version, but try to provide as much info as possible. I switched roms a few times in the last few days, going from Trents 8, to the newest Dirty Unicorns, to Trents 10 (where I started having issues) back to DU. I was trying to figure out where the issues came from, and came across someone saying that going from a touchwiz based rom, off of it, and back on, can cause problems. I then read that one of the best ways to fix this was to flash stock firmware and reflash new roms. I tried doing this...
Little did I know, it was a HUGE mistake for me to flash the 4.3 firmware through odin, and when the phone restarted, the "Galaxy Note II" page just kept flashing on and off for a few minutes. I think tried flashing older firmwares, with pit file, but I kept getting errors when I restarted saying that I didn't have Verizon Authorized Software.
Sooo this is where I'm stuck right now. I can't boot the phone at all, and when I try to flash the root66 firmware (the one that's supposed to fix everything?) I still get this verizon unauthorized page. It seems from what I've read that the bootloader relocked because of my 4.3 flash, and I can't find any info on how to unlock that. Anyone have suggestions? I'd really appreciate it!
Update: I retried the 4.3 firmware, and right now "Android is upgrading..." so I'm assuming this means my bootloader is locked, I've lost root, and all that jazz right? From what I've read so far there isn't any way to unlock the bootloader again, am I right? If so, can you point me in the right direction? Much appreciated!
Click to expand...
Click to collapse
No, the bootloader can't be unlocked. You can at least get root with saferoot on 4.3.
Or downgrade with mobile tech videos
Hi, guys
my phone is Huawei p10 Lite (WAS-LX2)
Note: if you have a bricked huawei p10 lite of any kind (incl WAS-LX2) (or a NZ model)
and you want to know how i finally fixed mine, jump down to the end where it says
GOOD NEWS
quick synopsis: unlocked bootloader, flashed twrp, now i get an error (255) when trying to create backup using twrp..
you can read the rest if you want but the above basically covers it please help
so i have unlocked my bootloader and flashed twrp, before i did this i did a factory reset through androids settings, the phone is also only two months old.. but i cannot create a backup using twrp, it always fails in the same place when backing up data, does this mean my stock rom that has never been altered in anyway ect is somehow corrupt? wtf? i havnt even rooted it yet, i was going to make a backup first (of a known good rom.. lol)
i am assuming the data files are part of the rom? not something you can ignore.. they were one of the few things selected by default.. i have tried rebooting phone a few times, formatting sd card etc (64gb) so there is plenty of space...
any help would be much appreciated
the tutorial i was following is here: https://forum.xda-developers.com/p10/how-to/twrp-how-to-root-p10-lite-t3617418
my phones full build (or do i mean firmware number?..) number: WAS-LX2C706B170
android version 7.0
emui 5.1
any more info, just ask..
also, ive heard that once you have installed twrp/ unlocked bootloader you cannot use system update or androids factory reset without bricking your phone? is that true? otherwise i want to try that, i just want to root my damn phone already... or... its been a long time since i last rooted a phone... you dont need root to make a twrp rom backup do you? nah, surely not..?
or could my twrp install be corrupt? the tutorial said to drag and drop the downloaded file into cmd, but that wasnt working so i entered the location manually, it still appeared to install fine that way though so surely thats not it. i dont know
ok, i just bricked my phone... i did a factory reset in twrp, thinking it was... a factory reset... i googled whether it was safe first and everything came up clean... but it is not it wiped the os or something and now i just get a boot loop... what the hell? how could i be so stupid?! and how could twrp not warn me.. it was just a factory reset? and i havnt even rooted it yet, at this point i would probably prefer it was rooted in the hope their would be more options available to me to un brick it.. ok now i really need someones help.. why am i drinking and trying to watch tv while doing this, i am so stupid, this is the best and most expensive phone ive ever owned, what have i done?! sorry sorry ill calm down...
so if my firmware number is: WAS-LX2C706B170 then can i use one of these (also for huawei p10 lite) and if so what would be the difference? why are the numbers slightly different? same phone model, different firmware/ slightly...
here they are:
WAS-LX2C706B120
WAS-LX2C185B121
and they each had a OTA and a full firmware version too.
here is the link: https://romfirmware.com/2017/08/04/huawei-p10-lite-was-lx2/
but before i try these things, is there any saving my current stock rom? i dont understand how a factory reset could prevent it from booting properly..? its not actually bootlooping, it either gets stuck on logo, or goes to black screen but you can still see the volume slider when pressing volume buttons, see the home and back buttons (which do nothing) and hear the lock sound when you press the power button... still always a black screen though.. i guess its possible i knocked the format data button in twrp but im 95% sure i didnt. if i remove twrp and install stock recovery would i be able to get the stock rom working that way? or is there any way to do an OTA update/ fix as i havnt rooted it yet so it should be capable (except i cant boot to rom..) if i hold down all buttons it seems to try to do something... it says emui then goes to 4% then says software install failed: the update package does not exsist. please download the package again... reboot system now..? whats that all about?
ok, so i have found a possible solution but would like confirmation from someone who knows these things first...
i found this tool: Huawei Firmware Finder (Team MT)
link: https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
and using this i have found my exact firmware, apparently straight from the official huawei update servers. the firmware number matches exactly, but there is no mention of it being for a huawei p10 lite so not 100% sure its a good idea, but if the whole firmware number matches perfectly and its the only one of its kind it must be the right one surely? and the size is the same as other huawei p10 lite firmwares..
here is the direct link:http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1514/g104/v89953/f2/full/update.zip
please someone else chime in to give me some advice...
is there any risk with flashing roms, or can i always still access twrp recovery to flash a new rom if i brick the phone?
cheers all
ok UPDATE:
i tried the repair file system option in twrp on the data partition just for fun (wrong word, im not having fun..) because i thought this rom was a lost cause..
upon reboot a huawei warning pops up saying the data partition has some serious damage and offers to try a low level format, it finishes successfully then restarts.
no change, still broken, but it offers to do a full format of data due to serious damage.
after restart phone boots fine, and enters setup wizard for first boot etc... perfect.
problem is, i still cant backup the data partition in twrp, still get same error:
createTarFork() process ended with ERROR: 255
bacjup failed..??
did i somehow get a brand new phone with a bad flash of a stock rom straight from the manuafacturer? with a slightly corrupted data partition... is there anyway to fix this? or can i assume the rom i downloaded from huaweis servers for my exact firmware is correct and i can use that as a backup in case i need it?
or in case my data is corrupt should i try to install that rom now?
or should i try to reflash twrp first and see if i can get a successful backup?
or should i just forget all this crap now my phone works and go straight to rooting it?
i really need some professional advice here.. lol
clearly i aint no expert
ok, so i noticed the frp was still locked for some reason so using adb, i relocked and unlocked bootloader, now frp is unlocked too, reflashed twrp, wiped dalvik cach/ cache, tried backup again...
no change, still fails on data partition, same error 255...?!
im lost,
close to trying to flash that rom i found...
or at least just rooting already..
OK UPDATE: first the bad news, then the good news:
so i gave up on backing up my data partition, as it was clearly somehow corrupt?...
so i went ahead and rooted my phone, everything was more or less working untill i used apps2sd...
that required several reboots and partitioning my sd card etc, then it said something about needing systemless root and a reboot, i went ahead with that and then my phone started bootlooping again, this time there was no fixing it, i of course tried removing sd card too.. nothing..
so i tried restoring to the rom i found using huawei firmware finder tool, that didnt work, using twrp to install zip, i got error -9? (couldnt find that one on the net..)
tried unzipping and putting update.app in dload folder on root of sd card, then booting to erecovery pressing vol- vol+ and power button, that also failed. now i was stressed near tears, this was the third day of research and trying to fix this... so i searche dhigh and wide, and gave up on stock roms, i figured that a custom rom designed for my chipset (hi6250)
and said to work on a huawei p10 lite then it should at least semi work on my phone, i did more research and the rom creator said to only use his version of TWRP to flash their ROM, so i reflashed to theirs... BIG mistake, if the custom recovery is the only thing you can boot into and the only way to access boot loader, do NOT risk losing it.. i did.. i lost my recovery..
so there for i lost my bootloader, so therefore i lost my ability to use ADB, or connect to pc in any way. i wanted to step in front of a bus at this point... but then there was:
GOOD news:
so i resorted to trying the official recovery roms on XDA for p10 lites, only i had been avoiding them as none of the build/ firmware numbers matched mine at all.. but i went ahead and clicked on the first download, (here is the link to post: https://forum.xda-developers.com/p10-lite/help/original-service-rom-huawei-p10-lite-t3688097) - you might find a few comments from me near the end there, lol..
anyway , once downloaded i unzipped and just pasted the dload folder straight to sd card and rebooted phone with all three buttons depressed. to my amazement when the huaei erecovery came up it started installing!!!? wow, i tried not to get my hopes up though..
first boot restarted after blue huawei splash logo, second boot went back to erecovery, offered factory reset and wipe cache(so i did), now it boots up perfectly every time like new, everything works! even gave me NZ language options etc, even though my build number didnt match any of those above, its still worked and even better it still shows all the correct information under about phone.
my build number was: WAS-LX2C706B170
so i can confirm it works for nz huawei p10 lites with 4gb ram and dual sim and WAS-LX2 builds
hope this helps someone else out there like me
tags: all official huawei rom,stock rom,twrp.stock,backup,official,rom finder,nandroid,back up, save,solution,fix,help,stuck,advice,simple,easy,guide,tutorial,root,huawei,p10,p10 lite,huawei p10 lite,was-lx1,was-lx2,firmware,iso,image,zip,file,download,error 255,255,error,createTarFork(),
Hey, just wanted to say thank you for posting this!
I'm from New Zealand, and have the exact same phone and the exact same issue.
Your "good news" section was exactly what I was looking for, and helped me fix my phone.
Cheers, George
update copy
Hi was wondering if you have a copy of the update you used as it is near impossible to get from the link on the other thread. Another Kiwi with a bricked phone.
All good, after 4 hours it finally downloaded. I will keep a copy in case anyone needs it. WAS-LX2