(GUIDE) A2017U Desbrickear/UnBrick ZTE AXON 7 - ZTE Axon 7 Guides, News, & Discussion

I can not be held responsible if you do not follow the instructions and your phone explodes in your face, you get wings and fly, your microsd smoke etc. EVERY PROCEDURE YOU MAKE ON YOUR PHONE IS ONLY YOUR RESPONSIBILITY.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
As you notice, this process also enables fastboot commands.
This is a step-by-step tutorial to get the Brick phone
I leave a video as a reference that I recorded in addition to the files and drivers you need.
Either because of bad flashing, you were wrong with bootstacks or ROM.
1.- See that the phone is off
2.- Press Volume + and Volume - and the Power key at the same time until the LED turns on and off in Red, that means that you are already in EDL Emergency mode.
3.- Connect the phone and Install the Drivers
4.- When you see that Qualcomm HS-USB QDLoader 9008 and a COM port have been installed
5. Open MiFlash and copy the address of the unpacked A2017U_B19-NOUGAT_TWRP_EDL package into the address bar.
click on Refresh and when the COM port of your phone comes out click on Flash.
If everything goes well you will see that the process begins and at the end it will say Ready, then you have to disconnect the phone and press power about 10 seconds later and press power again until it turns on. You should be able to enter TWRP to restore your backup or flash a new ROM.
Even it is very likely that the rom you had installed start.
https://www.youtube.com/watch?v=dHB61cMurG4&t=10s
Link MiFlash: http://www.mediafire.com/file/25fu9boj245wynz/MiFlash20161222.zip
LinkB19 EDL TWRP: https://build.nethunter.com/misc/axon7/A2017U_B19-NOUGAT_TWRP_EDL.zip
Link Drivers Qualcomm: https://androidfilehost.com/?fid=745425885120754986
Link Drivers ZTE: http://phoneusbdrivers.com/zte-axon-7-usb-driver/
Update: All Links in 1 uploaded by me: https://drive.google.com/file/d/16Szwb4paI-aBH-v8gxbuVi0xMf-NdxLp/view?usp=sharing

---

TheDarkKnightSM said:
I can not be held responsible if you do not follow the instructions and your phone explodes in your face, you get wings and fly, your microsd smoke etc. EVERY PROCEDURE YOU MAKE ON YOUR PHONE IS ONLY YOUR RESPONSIBILITY.
As you notice, this process also enables fastboot commands.
This is a step-by-step tutorial to get the Brick phone
I leave a video as a reference that I recorded in addition to the files and drivers you need.
Either because of bad flashing, you were wrong with bootstacks or ROM.
1.- See that the phone is off
2.- Press Volume + and Volume - and the Power key at the same time until the LED turns on and off in Red, that means that you are already in EDL Emergency mode.
3.- Connect the phone and Install the Drivers
4.- When you see that Qualcomm HS-USB QDLoader 9008 and a COM port have been installed
5. Open MiFlash and copy the address of the unpacked A2017U_B19-NOUGAT_TWRP_EDL package into the address bar.
click on Refresh and when the COM port of your phone comes out click on Flash.
If everything goes well you will see that the process begins and at the end it will say Ready, then you have to disconnect the phone and press power about 10 seconds later and press power again until it turns on. You should be able to enter TWRP to restore your backup or flash a new ROM.
Even it is very likely that the rom you had installed start.
&t=10s
Link MiFlash: http://www.mediafire.com/file/25fu9boj245wynz/MiFlash20161222.zip
LinkB19 EDL TWRP: https://build.nethunter.com/misc/axon7/A2017U_B19-NOUGAT_TWRP_EDL.zip
Link Drivers Qualcomm: https://androidfilehost.com/?fid=745425885120754986
Link Drivers ZTE: http://phoneusbdrivers.com/zte-axon-7-usb-driver/
Update: All Links in 1 uploaded by me: https://drive.google.com/file/d/16Szwb4paI-aBH-v8gxbuVi0xMf-NdxLp/view?usp=sharing
Click to expand...
Click to collapse
Crap forget what I said, it was right on the title...
Would be much better if you:
a) made it for all 3 models with a link to WesTD's EDL package thread
b) said something about DFU (if you make it for the other models) and how this will not work on them if the driver is the dfu one (zte handset diagnostic interface)
Add somewhere on the guide that it is only for the U just in case.

---

Choose an username... said:
Crap forget what I said, it was right on the title...
Would be much better if you:
a) made it for all 3 models with a link to WesTD's EDL package thread
b) said something about DFU (if you make it for the other models) and how this will not work on them if the driver is the dfu one (zte handset diagnostic interface)
Add somewhere on the guide that it is only for the U just in case.
Click to expand...
Click to collapse
both in the title and in the guide in the mention of the package, it is said that it is only for A2017U, even though I will have a clarification in red and great, if any. Thank you.
Sent from my ZTE Axon 7 using XDA Labs