Hi guys.
I need some clear instructions, and software needed to install Windows 7 on my TG01. I do not know most of the stuff I see posted in threads, so I need something even a retard could do.
It already has WM 6.5 on it. And it works well. I need something with a great chance of not bricking it.
anyone help plz
N00b guide
There is certainly not an obvious way to flash a TG01, especially to WP7, so here is a rough guide it's not perfect but hopefully this works for you. Please read and download everything you need before beginning the process.
Step 1: Flash WP7 bootloader
1) Download and install TG Downloader and the USB drivers. Reboot PC.
2) Fully charge your device battery. (Buy a cheap universal battery charger from eBay if necessary.)
3) Switch off your device.
4) Place your TG01 into "Download mode" as follows...
Devices with 0321 ROMs: Hold down Camera + Power buttons on boot.
Otherwise: Remove back cover, battery and SIM card. Carefully remove black sticker where the SIM card was. Get a piece of copper wire and twirl it so that you can easily hold it and touch Pin 1 and Pin 3 at the same time (known as "shorting"), see below image. Replace battery, short the pins with the copper wire and press the Power button.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After either of these your device should display a white LED on the front which means it is in Download mode. If not, switch off and try again. Also if using the PIN method, maybe try holding the Reset button on the back for 10 seconds straight after pressing the Power button.
5) Connect phone to PC. Start TG Downloader with admin rights (right-click shortcut or EXE and choose "Run as administrator".
6) TG Downloader will display an error, click "yes". Click change port to change to Toshiba DL port if necessary. Click "Download mode".
7) Download and extract wp7boot.bin, browse to it in TG Downloader and click "Start Download".
8) Do not disconnect your phone until the process completes, it shouldn't take longer than 5-10mins.
Step 2: Flash WP7 ROM
1) Download and extract these OS files. Install the Acer driver (32 or 64bit) and the ZTEiT Common Downloader.
2) Download a WP7 ROM. I recommend one of the latest 7.8 builds. Once the ROM is downloaded, extract, rename to flash.bin and place in the same directory as NPRG8650.hex and partition.mbn.
3) Fully charge your device battery.
4) Switch off your device.
5) Hold Camera + Power to boot into Download mode, device should display a blue LED.
6) Connect to PC. Start ZTEiT Common Downloader. Select Multi-Download.
7) Browse to folder with downloaded files. Click advanced and for each of the three files (flash.bin, NPRG8650.hex and partition.mbn) browse to them.
8) Click Start to begin flashing process. Do not disconnect device until complete. Could take 15-25mins.
Then your device should boot up into your new WP7 software. Please note camera does not function in any WP7 builds AFAIK and there may be bugs or other limitations.
If this guide works, please go thank these guys: qinwengui, mirolg, arag0n85 and kevinpwhite. Of course thank the ROM creator too :victory:
help please
I never got to put the mobile in download mode, load some files previously in sd?
Thanks, I need it
p.d: I could only sd dowloading but gives error sd
TG01 SOS Failed in Flash wm6.5 to wm 7.0
Hi
Could anyone please help/assist me with this problem i would be great full.
I have a toshiba TG01 phone with windows moblie 6.5
I'm trying to upgrade/flash to load windows mobile 7 (mi7ROM_4_tango_8773_final.zip)
and i am failling to do it..
when i get to short hot wireing the phone to force it to install the contents of the "PRG" folder it comes with a white screen saying filed to download.
what files should be in the "PRG" and what do they do/mean?
My email: [email protected]
Hey, I know it's pretty outdated but does anybody here happen to have the TG Downloader still?
If so, that'd be very helpful if you can re-upload it to somewhere...
Related
i was fixing my brick vibrant using odin. i loaded up the files called 512.pit, and T959UVJI6, and i started the odin with my download moded vibrant pluged into computer and also with the re-partition checked. i know that i shouldn't have checked re-partition but i didn't know
here is what went so wrong. hysterically, my vibrant was unpluged somehow while the odin was processing something even it said 'DO NOT REMOVE TARGET'.
now i got a new brick vibrant. (look at the picture attached)
computer no longer be able to read my device and the phone won't goto download mode.
(power bottom + voulme up and down is not working, and also taking off battery+SIMcard+SDcard and pressing up/down volume and re-insert batter not working)
help me~
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Go to the sticky it has some detailed info on how to fix,
Basically you will need to go into recovery by using the hold down the volume/on buttons with the battery removed and then plug the usb into the computer with Odin already up, this should get you back into recovery then:
1. Download Eugenes 'Froyo that does not brick' file.
2. Extract the files.
3. While in download mode load the files.
4. load the PIT file in appropriate area.
5. load the .tar file in the PDA area.
6. DO NOT check 're-partition'.
7. Click start, let it finish. Your phone will load and reboot into stock recovery. It will error out again. DONT panic! This is what's supposed to happen.
8. Now, pull your battery.
9. Download the 'JFD file
11. Once again, open Odin, plug in your phone, put into download mode.
12. Load the PIT file into the appropriate area and the .tar in the PDA area.
13. THIS TIME you want to check the 're-partition' box.
14. Now click start, let it finish, and this time your phone will load up just fine!
good luck...............
Been there dude. Just keep trying to get Odin to recognize it, maybe restart your PC. I may have also tried rebooting into Download mode (3 buttons) to get the issue resolved. Just keep at it in Odin.
Try these steps if you havent already:
1. Remove USB from phone, take the battery out and put it back in (to make sure its off)
2. Open Odin and plug USB into PC
3.Hold both Vol buttons while connecting USB to phone
4. Phone should go into download.
If not then you need a JIG
thank you
i finally go into the download mode. i followed all each of you guys' suggestions.
thank you all very much~~~~~~~ good night!
simple solution
Go to this addy: http://forum.xda-developers.com/showthread.php?t=954509
It is Baywolf's AIO Toolbox 2.5 do all the steps I describe below and it will restore it back
To Eclair 2.1.1
First though keep you sim and SD card in, pull the battery, open up the program, connect your USB cable to the phone, then put the battery back in! Baywolfs program will detect it, you'll see a port yellow color appear, you now can do a restore, click the flash to stock button, and click pit, use his drop-down list, its already provided, then hit the PDA button, use the tar file he again provided, now its ready, hit the start button, and It will re-flash it back to Eclair 2.1.1 with 0 defects, its an awesome program, and this was the only program, that got me up and running, ODIN and Heimdall's wouldn't respond, but this one saved my ass! trust me, I was in the same scenario, your in! I now have axura 2.3.1.0 up and back running, and I got into that delimna by trying to downgrade a modem, and ODIN totally hosed me up!
Good Luck
I left it to the toshiba locked, when I was doing and I was wp7 flash with blue LED, the light went home and I turn off the computer, which the mobile will restart after a while and so far no signs of life, not by giving the power vibrating or LED lights, and prove your all keystrokes and nothing, no response, I guess I can throw it?
yup, or find anyone with riffbox in the near
Same probelm here!!
The LED isn't showing! I can't charge the phone too!!
What else can I do??
Sent from my HTC Desire S using xda premium
or buy a box riff and you spend the money it or throw the phone away, little else can we do for the
you remove the battery, then insert battery and press the camera to power and blue LED back light, plug the machine back to conect with pc and then use the tool of nokser to up the bootloader, so I was already living and TG01 again, hope you do the same
tuandinh said:
you remove the battery, then insert battery and press the camera to power and blue LED back light, plug the machine back to conect with pc and then use the tool of nokser to up the bootloader, so I was already living and TG01 again, hope you do the same
Click to expand...
Click to collapse
We can't.. even the led won't come on at all. It can't boot to bootloader mode.
Sent from my HTC Desire S using xda premium
i herd somewhere in another thread you can basically jumpstart a tg01 battery by cutting a usb cable or something. i wouldnt try it unless you know what you are doing tho
Hi,
I had the same problem but after waiting a few days, with battery out of phone, and retried holding camera and power button the blue light came back on. But I don't know where to go from there, tg downloader doesn't detect my phone?
Thanks
jonslayer0 said:
Hi,
I had the same problem but after waiting a few days, with battery out of phone, and retried holding camera and power button the blue light came back on. But I don't know where to go from there, tg downloader doesn't detect my phone?
Thanks
Click to expand...
Click to collapse
NOT WITH TG DOWNLOADER! YOU NEED THIS STEPS BEFORE:
to get the 6.5.x Bootloader:
go in bootloader mode Camera+Power (Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished you have the 6.5 bootloader! NOW charge your battery 5-6 hours full
Prepare a 6.5.x .TSW ROM as .BIN ROM
TSW TOOLS
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Toshiba_TSW.zip - encoder/decoder for tsw files / bin files
tnx http://cotulla.pp.ru/Misc.html
- browse to your toshiba ROM .tsw, then select Toshiba TG01 and you get a toshiba ROMas .bin file- ready to flash with TG Downloader
use/install TG-Downloader + Toshiba drivers. bring with Camera+Power to Download mode use TG-Downloader to flash the 6.5 BIN ROM
the tools + files + tut you find here: toshiba tg01 WP7 ROM
mirolg said:
NOT WITH TG DOWNLOADER! YOU NEED THIS STEPS BEFORE:
to get the 6.5.x Bootloader:
go in bootloader mode Camera+Power (Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished you have the 6.5 bootloader! NOW charge your battery 5-6 hours full
Prepare a 6.5.x .TSW ROM as .BIN ROM
TSW TOOLS
Toshiba_TSW.zip - encoder/decoder for tsw files / bin files
tnx http://cotulla.pp.ru/Misc.html
- browse to your toshiba ROM .tsw, then select Toshiba TG01 and you get a toshiba ROMas .bin file- ready to flash with TG Downloader
use/install TG-Downloader + Toshiba drivers. bring with Camera+Power to Download mode use TG-Downloader to flash the 6.5 BIN ROM
the tools + files + tut you find here: toshiba tg01 WP7 ROM
Click to expand...
Click to collapse
I solved my problem in this thread:
http://forum.xda-developers.com/showthread.php?p=19266884#post19266884
3/4/15 NEW HOWTO ROOT & install TWRP on DL701Q/DigiLand 7" Tablet 4.4.2 KitKat
Ok, So you got your new Super Cheapo MTK8127 quad core Tablet from BestBuy or some other overpriced electronics emporium and want to install root and a custom recovery So it won't suck nearly as bad
Feeling hungry but don't wanna feed yourself??? Open wide......Here comes the airplane requesting permission to land
The Following procedure may "BRICK" your tablet and wipe your porn....You do so at your own risk, Neither Kneee or his lawyer claim to know ANYTHING about android....or anything else for that matter
THIS GUIDE WILL WIPE YOUR PORN!!!
If you've ever seen THIS:http://forum.xda-developers.com/chef-central/android/root-dl701q-install-twrp-touch-recovery-t2980339thread, You know that "iRoot/vRoot no longer works since updating to kitkat. I've BUNGLED my way into a solution, Hope it helps you too.....
THIS GUIDE ASSUMES YOU KNOW HOW TO USE ADB AND FASTBOOT (ENABLE USB DEBUGGING)OR AT LEAST KNOW WHAT THEY ARE AND DON'T SUFFER FROM GOOGLEPHOBIA
#1 Making a backup of this crap software when ADB , FASTBOOT and SP flash tool are working correctly is pointless (IMHO) (inm
Here's Everything you should need:
Stock ROM COURTESY...THIS DUMBASS https://drive.google.com/file/d/0B9DmzLnUt5tuaUtJS1FHcjNyX1U/view?usp=sharing
ADB_&_FASTBOOT_executables, no need to install, just extract the .zip to the directory of your choice and execute openCMD.bat with a right click + run as administrator. it will open a terminal window, you can run all your ADVB & FASTBOOT commands from there:https://drive.google.com/file/d/0B9DmzLnUt5tuM29vOTNHNEZya2s/view?usp=sharing
Driver installer & MTK_SP_FLASH_TOOL for MT8127 use this to install the drivers and flash the stock rom + custom recovery.img https://drive.google.com/file/d/0B9DmzLnUt5tudVlrSEtzSE1tWHc/view?usp=sharing
UBIFS_Modified_CWM FOR FLASHING UPDATE-SuperSU-v2.46.zip COURTESY Vampirefo: https://drive.google.com/file/d/0B9DmzLnUt5tueC04RDFVX3plTVk/view?usp=sharing
UPDATE-SuperSu-v2.46.zipflash this with vampirefo's modified CWM recovery image UBIFSRecovery4SuperSu.img" https://drive.google.com/file/d/0B9DmzLnUt5tuZjlmVm1Wc2tFUTA/view?usp=sharing
TWRP Setup.exe...Used to install TWRP recovery after flashing Stock ROM + Custom recoveryCOURTESY TWRP team & Protocol 9https://drive.google.com/file/d/0B9DmzLnUt5tuTVVJS2d2RERpbVk/view?usp=sharing
STEP 1: INSTALL THE DRIVERS INSIDE THE MT8127 SP_FLASH_TOOL.zip" file you downloaded It will install the mtk usb vCOM driver we need for the mtk8127. if u have questions PM vampirefo. after that, turn your tablet upside down, FIND THE reset hole and jam the nearest tiny object in there until the screen does something different (like go black) release the reset button, hold VOLUME DOWN and plug in the USB cord and the tablet should be reconized as a preloader USB VCOM Port device under "Ports" in Device Manager
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
So, the necessary driver to save this POS is at hand. after it's done installing the tablet will probably reboot and the remaining drivers will install. (EVEN WITHOUT THE OTHER DRIVER YOU CAN ROOT AND FLASH NOW)
Fire up the MT8127 SP flash tool (run as administrator) you downloaded and you should see this:
Click "Scatter-Loading" and select the scatter file located in the stock rom folder you downloaded and unzipped (you DID unzip it right?) and click the "RECOVERY" FIELD LOCATED HERE:
and select the recovery image you downloaded called "UBIFSRecovery4SuperSu.img......yay, you should be all set up and ready to go!
Make sure youve already unplugged the USB cable AND hit the reset button. HIT THE DOWNLOAD BUTTON (the program is now waiting for your device...no rush) HOLD VOLUME DOWN AND PLUG IN THE USB CABLE, the computer will detect the device, the program will proceed to shove a bunch of ones and zeros down the the tablets throat and it will reboot (hopefully to a mediatek logo).
If so, youre not as stupid as everyone says when u leave the room
Toss "UPDATE-SuperSU-2.46.zip" on a microSD, Power off the device, shove the SD in his home and hold POWER + VOLUME UP until you get prompted to select either RECOVERY OR FASTBOOT, we want recovery so make sure it's selected and press VOLUME DOWN to boot into recovery & install your SuperSU.zip and reboot
once the OS is fully running, run TWRP.exe as ADMINISTRATOR in AUTO mode, TWRP recovery should be installed and u should still have root, if not, you'll need to go into advanced, then mount system before re-installing from zip.
NOW learn ADB and fastboot so I can save my breath next time:
PS, all your GAPPS are gone....quit *****ing, I've got em here: htpa_gapps-modular-micro-4.4.2-20140608-signed.zip(pa_gapps-modular-micro-4.4.2-20140608-signed.zip 85.3MB) & HERE: https://drive.google.com/file/d/0B9DmzLnUt5tuSl9lME9VZnFJTU0/view?usp=sharing(pa_gapps-stock-4.4.2-20140608-signed.zip 267MB))
I have requested this thread be removed, you are using my stuff without permission, and even crediting yourself with the firmware, I took the time to download, you yourself have done nothing but take others work including mine without permission.
Hi, I am trying to root this phone using the guide here: bbs.elephone.hk/thread-9919-1-1.html#.WGr04lzUHIU
However in Windows 10, nothing happens when I hit the download button, and in Linux this error happens when using the files I got from the guide:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
this is the same PC, with Ubuntu and Windows 10 dual boot
I have tried the fastboot method, but I can't get my bootloader to unlock, the vol up button simply doesn't register on the phone.
So is there any fix? Or am missing something?
Problem solved! Windows 10 doesn't like the drivers provided. However Windows 7 does, so I advise that you keep your Windows 7 install somewhere
Follow this it will explain what you need to do. I had same issue with Windows 10 but rooted my P9000 no problem. I used FlashTools - all the info you need here:
https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
I gave up following tutorials on elephone.hk forum & just followed tutorials from here, but whatever your personal preference - hope it helps ;0)
Need my elephone back
Not sure if this is best placed here???
So....tried to flash my Elephone P9000 using the SmartPhone Flash Tool and all the steps provided tutorial at:
https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
Using Win10 so it took me a while to disable the driver signature enforcement option to get the drivers installed. Got that done and all..so far so good.
Download all the files as the tutorial says...clicked download and connected the phone which was powered off. Up pops a messages "PMT changed for ROM; it must be downloaded."
Google search for this and came across some pages that informed me to click on the 'Format' section in the Flash Tool
Did this and then went back into 'Download' and hey presto, the flash worked and I got the big green tick.
Lovely stuff...until I tried to power on my phone....dead in the water. Power+Volume Up does nothing, power on its own does nothing. I've downloaded loads of instances of the Flash Tool, tried the elephone stock ROM scatter file, recovery image files etc and still nothing. Read loads of similar pages where it's happened to others but just wont work for me!!!!
Can anyone help?
jfk247 said:
Not sure if this is best placed here???
So....tried to flash my Elephone P9000 using the SmartPhone Flash Tool and all the steps provided tutorial at:
https://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
Using Win10 so it took me a while to disable the driver signature enforcement option to get the drivers installed. Got that done and all..so far so good.
Download all the files as the tutorial says...clicked download and connected the phone which was powered off. Up pops a messages "PMT changed for ROM; it must be downloaded."
Google search for this and came across some pages that informed me to click on the 'Format' section in the Flash Tool
Did this and then went back into 'Download' and hey presto, the flash worked and I got the big green tick.
Lovely stuff...until I tried to power on my phone....dead in the water. Power+Volume Up does nothing, power on its own does nothing. I've downloaded loads of instances of the Flash Tool, tried the elephone stock ROM scatter file, recovery image files etc and still nothing. Read loads of similar pages where it's happened to others but just wont work for me!!!!
Can anyone help?
Click to expand...
Click to collapse
this usually happends when your flashing with old preloader... try installing CM13 with updated preloader, it should work.
Thanks Ruben, I managed to get the green tick in the sm flash tools using the 'Elephone P9000 Preloader_Lk_Boot_Recovery update' scatter text file.
Phone still wont power on at all and i can't access the sd card to copy across any ROMS so I'm back to square 1 by the looks of it. I'll keep pluggin away at it.
I can not be held responsible if you do not follow the instructions and your phone explodes in your face, you get wings and fly, your microsd smoke etc. EVERY PROCEDURE YOU MAKE ON YOUR PHONE IS ONLY YOUR RESPONSIBILITY.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
As you notice, this process also enables fastboot commands.
This is a step-by-step tutorial to get the Brick phone
I leave a video as a reference that I recorded in addition to the files and drivers you need.
Either because of bad flashing, you were wrong with bootstacks or ROM.
1.- See that the phone is off
2.- Press Volume + and Volume - and the Power key at the same time until the LED turns on and off in Red, that means that you are already in EDL Emergency mode.
3.- Connect the phone and Install the Drivers
4.- When you see that Qualcomm HS-USB QDLoader 9008 and a COM port have been installed
5. Open MiFlash and copy the address of the unpacked A2017U_B19-NOUGAT_TWRP_EDL package into the address bar.
click on Refresh and when the COM port of your phone comes out click on Flash.
If everything goes well you will see that the process begins and at the end it will say Ready, then you have to disconnect the phone and press power about 10 seconds later and press power again until it turns on. You should be able to enter TWRP to restore your backup or flash a new ROM.
Even it is very likely that the rom you had installed start.
https://www.youtube.com/watch?v=dHB61cMurG4&t=10s
Link MiFlash: http://www.mediafire.com/file/25fu9boj245wynz/MiFlash20161222.zip
LinkB19 EDL TWRP: https://build.nethunter.com/misc/axon7/A2017U_B19-NOUGAT_TWRP_EDL.zip
Link Drivers Qualcomm: https://androidfilehost.com/?fid=745425885120754986
Link Drivers ZTE: http://phoneusbdrivers.com/zte-axon-7-usb-driver/
Update: All Links in 1 uploaded by me: https://drive.google.com/file/d/16Szwb4paI-aBH-v8gxbuVi0xMf-NdxLp/view?usp=sharing
TheDarkKnightSM said:
I can not be held responsible if you do not follow the instructions and your phone explodes in your face, you get wings and fly, your microsd smoke etc. EVERY PROCEDURE YOU MAKE ON YOUR PHONE IS ONLY YOUR RESPONSIBILITY.
As you notice, this process also enables fastboot commands.
This is a step-by-step tutorial to get the Brick phone
I leave a video as a reference that I recorded in addition to the files and drivers you need.
Either because of bad flashing, you were wrong with bootstacks or ROM.
1.- See that the phone is off
2.- Press Volume + and Volume - and the Power key at the same time until the LED turns on and off in Red, that means that you are already in EDL Emergency mode.
3.- Connect the phone and Install the Drivers
4.- When you see that Qualcomm HS-USB QDLoader 9008 and a COM port have been installed
5. Open MiFlash and copy the address of the unpacked A2017U_B19-NOUGAT_TWRP_EDL package into the address bar.
click on Refresh and when the COM port of your phone comes out click on Flash.
If everything goes well you will see that the process begins and at the end it will say Ready, then you have to disconnect the phone and press power about 10 seconds later and press power again until it turns on. You should be able to enter TWRP to restore your backup or flash a new ROM.
Even it is very likely that the rom you had installed start.
&t=10s
Link MiFlash: http://www.mediafire.com/file/25fu9boj245wynz/MiFlash20161222.zip
LinkB19 EDL TWRP: https://build.nethunter.com/misc/axon7/A2017U_B19-NOUGAT_TWRP_EDL.zip
Link Drivers Qualcomm: https://androidfilehost.com/?fid=745425885120754986
Link Drivers ZTE: http://phoneusbdrivers.com/zte-axon-7-usb-driver/
Update: All Links in 1 uploaded by me: https://drive.google.com/file/d/16Szwb4paI-aBH-v8gxbuVi0xMf-NdxLp/view?usp=sharing
Click to expand...
Click to collapse
Crap forget what I said, it was right on the title...
Would be much better if you:
a) made it for all 3 models with a link to WesTD's EDL package thread
b) said something about DFU (if you make it for the other models) and how this will not work on them if the driver is the dfu one (zte handset diagnostic interface)
Add somewhere on the guide that it is only for the U just in case.
Choose an username... said:
Crap forget what I said, it was right on the title...
Would be much better if you:
a) made it for all 3 models with a link to WesTD's EDL package thread
b) said something about DFU (if you make it for the other models) and how this will not work on them if the driver is the dfu one (zte handset diagnostic interface)
Add somewhere on the guide that it is only for the U just in case.
Click to expand...
Click to collapse
both in the title and in the guide in the mention of the package, it is said that it is only for A2017U, even though I will have a clarification in red and great, if any. Thank you.
Sent from my ZTE Axon 7 using XDA Labs