Hi! I bricked my tv box and she stop work,only show amlogic logo.
I looking for firmware for tv android box M8 tt amlogic s802 with realtek 8723bs chip
I tray many rom who find on internet but without results. Motherboard is M8&M9_V02
I cant find ROM,anyone help me please?
In time when i wait for help i flash rom for probox Probox-ex2 with sd card an have functionaly tv box,but no work wifi bloototh and remote control. I tray many many roms,only this probox and rom for mx III have boot and everthing work but wifi bt nd remote control no,because in my box is realtek wifi chip.Now,i dont know how to port realtek driver in my rom...if anybody have seems box can you make backup and upload it?
I have fount 2 rom who works on this box,but no working wifi,remote control and bluetooth...one rom is for probox ex2 and other is for mx III and booth works ok but no wifi...How to flash driver for wifi only in this rom?
i have the same ott tv m8 Fake box!
But i´m confused with this little box from Hell.
For me Probox Ex2 Rom ends with flashing at 2%. I have to flas via USB Burning Tool, because another earlier Firmware flash had to go wrong.
what is with the other Rom? You talk about 2 Roms.
Probox Ex2 Rom must flash with tothpick method and sd card,also other rom for mx 3
Related
Hi
I purchased from lightake.com a android TV, named as "MK809III RK3188 Cortex-A9 Quad Core 1.8GHz TV Box w/ Bluetooth WIFI HDMI OTG 2GB/8GB Black" It came with 4.1.1 installed and although sometimes it reseted by itself, it was working. As from the outside it's just the same shell as W2COMP's and it was named equally I installed the MK809III 4.2 version available at w2comp.
It took some time to flash it, because the reset hole was not over the reset switch... OK, I just did a new hole and I was able to flash it.
The problem is that now it properly boots, but neither the WiFi nor Bluetooth work anymore... I began to read about the many names of the beast... I found that Rikomagic 809IV was said to be the same... I downloaded the firmware, I flashed it but the WiFi still doesn't work... Same happened with other ROMs. (MK820IV, from rikomagic, tronsmart MK908)
I guess that the problem is that the WiFi/Bluetooth chipset is an AP6210, and it’s not supported on these ROMs.
I have been said that this was an UGOOS unit and their sales dpt. has told me that they haven't produced any RK3188 with AP6210 inside...
Can you help me to identify it? Or tell me which ROM could be suitable for this? Or a original ROM?
Best regards and thank you!!
Eduardo
did you back up the rom using nandroid backup app to sd card? ?
jedu said:
Hi
I purchased from lightake.com a android TV, named as "MK809III RK3188 Cortex-A9 Quad Core 1.8GHz TV Box w/ Bluetooth WIFI HDMI OTG 2GB/8GB Black" It came with 4.1.1 installed and although sometimes it reseted by itself, it was working. As from the outside it's just the same shell as W2COMP's and it was named equally I installed the MK809III 4.2 version available at w2comp.
It took some time to flash it, because the reset hole was not over the reset switch... OK, I just did a new hole and I was able to flash it.
The problem is that now it properly boots, but neither the WiFi nor Bluetooth work anymore... I began to read about the many names of the beast... I found that Rikomagic 809IV was said to be the same... I downloaded the firmware, I flashed it but the WiFi still doesn't work... Same happened with other ROMs. (MK820IV, from rikomagic, tronsmart MK908)
I guess that the problem is that the WiFi/Bluetooth chipset is an AP6210, and it’s not supported on these ROMs.
I have been said that this was an UGOOS unit and their sales dpt. has told me that they haven't produced any RK3188 with AP6210 inside...
Can you help me to identify it? Or tell me which ROM could be suitable for this? Or a original ROM?
Best regards and thank you!!
Eduardo
Click to expand...
Click to collapse
vwbug2007 said:
did you back up the rom using nandroid backup app to sd card? ?
Click to expand...
Click to collapse
Nope...
JEdu
jedu said:
Hi
I purchased from lightake.com a android TV, named as "MK809III RK3188 Cortex-A9 Quad Core 1.8GHz TV Box w/ Bluetooth WIFI HDMI OTG 2GB/8GB Black" It came with 4.1.1 installed and although sometimes it reseted by itself, it was working. As from the outside it's just the same shell as W2COMP's and it was named equally I installed the MK809III 4.2 version available at w2comp.
It took some time to flash it, because the reset hole was not over the reset switch... OK, I just did a new hole and I was able to flash it.
The problem is that now it properly boots, but neither the WiFi nor Bluetooth work anymore... I began to read about the many names of the beast... I found that Rikomagic 809IV was said to be the same... I downloaded the firmware, I flashed it but the WiFi still doesn't work... Same happened with other ROMs. (MK820IV, from rikomagic, tronsmart MK908)
I guess that the problem is that the WiFi/Bluetooth chipset is an AP6210, and it’s not supported on these ROMs.
I have been said that this was an UGOOS unit and their sales dpt. has told me that they haven't produced any RK3188 with AP6210 inside...
Can you help me to identify it? Or tell me which ROM could be suitable for this? Or a original ROM?
Best regards and thank you!!
Eduardo
Click to expand...
Click to collapse
yadi.sk/d/T9LLU1wH5tZRa work
Rikomagic MK802IV with AP6210 support
Official Rikomagic ROM
Try this MK802IV rom, as it's a new rom that's developed with AP6210 support
http://www.sendspace.com/pro/dl/z80zb4
Good luck
--------- Just realized that the link is dead, also the official link is down so I guess that you'll have to keep an eye on the rikomagic forum until a new one pops up.
http://minipute.com/2013/07/24/new-mk802iv-custom-rom-supports-ap6210-wi-fi-chip/2531
jedu said:
Hi
I purchased from lightake.com a android TV, named as "MK809III RK3188 Cortex-A9 Quad Core 1.8GHz TV Box w/ Bluetooth WIFI HDMI OTG 2GB/8GB Black" It came with 4.1.1 installed and although sometimes it reseted by itself, it was working. As from the outside it's just the same shell as W2COMP's and it was named equally I installed the MK809III 4.2 version available at w2comp.
It took some time to flash it, because the reset hole was not over the reset switch... OK, I just did a new hole and I was able to flash it.
The problem is that now it properly boots, but neither the WiFi nor Bluetooth work anymore... I began to read about the many names of the beast... I found that Rikomagic 809IV was said to be the same... I downloaded the firmware, I flashed it but the WiFi still doesn't work... Same happened with other ROMs. (MK820IV, from rikomagic, tronsmart MK908)
I guess that the problem is that the WiFi/Bluetooth chipset is an AP6210, and it’s not supported on these ROMs.
I have been said that this was an UGOOS unit and their sales dpt. has told me that they haven't produced any RK3188 with AP6210 inside...
Can you help me to identify it? Or tell me which ROM could be suitable for this? Or a original ROM?
Best regards and thank you!!
Eduardo
Click to expand...
Click to collapse
(Old thread, I know, but might help others.)
This ROM works wonders for me:
NEOMODE CUSTOM ROM MK809III AP6210 Version 1.9a
If you are a bit more daring, try this:
MK809III AP6210 NEOTV CROM Version 2.0 1080p
(I'm not yet allowed to post URLs on this forum, so you'll have to use Google).
jedu said:
Hi
I purchased from lightake.com a android TV, named as "MK809III RK3188 Cortex-A9 Quad Core 1.8GHz TV Box w/ Bluetooth WIFI HDMI OTG 2GB/8GB Black" It came with 4.1.1 installed and although sometimes it reseted by itself, it was working. As from the outside it's just the same shell as W2COMP's and it was named equally I installed the MK809III 4.2 version available at w2comp.
It took some time to flash it, because the reset hole was not over the reset switch... OK, I just did a new hole and I was able to flash it.
The problem is that now it properly boots, but neither the WiFi nor Bluetooth work anymore... I began to read about the many names of the beast... I found that Rikomagic 809IV was said to be the same... I downloaded the firmware, I flashed it but the WiFi still doesn't work... Same happened with other ROMs. (MK820IV, from rikomagic, tronsmart MK908)
I guess that the problem is that the WiFi/Bluetooth chipset is an AP6210, and it’s not supported on these ROMs.
I have been said that this was an UGOOS unit and their sales dpt. has told me that they haven't produced any RK3188 with AP6210 inside...
Can you help me to identify it? Or tell me which ROM could be suitable for this? Or a original ROM?
Best regards and thank you!!
Eduardo
Click to expand...
Click to collapse
If you open the case (use a guitar pick to gently prise open the case going around a little at a time) you'll be able to see the wifi chip which will be marked with its make and model.
Greetings.
Hey , guys, I'm a Chinese user.Recently I got an amlogic 8726 MX device and I want to run linux on it.The device is Tmall MagicBox.
I have trid the buildroot of [email protected] and it work for this device.I used the amlogic_mx_defconfig for compiling.It seems that this device is familiar with meson6. But there is somehing trobles me.One is I don't know how to map the remote keys.BTW,the remote of this devide is work under 2.4ghz,not the ir remote.Another problem is , the built-in usb wifi model can't work. The wifi model is RTL8188EU. Maybe the meson6's configure don't completely match this device.So,how should I do to add support for this new device?
Thanks.
I just bought this HDMI DLNA / Miracast receiver stick. The model seems to be a "Ugoos UG017" aka "Chromecast MD321" aka "MOCREO iPush M1" aka "HI762 HI763 (Chromecast)" aka "CX-V3" aka "PTV-2R" and possible more names. The hardware is:
- Rockchip RK2928-G @~1GHz
- 256MB DDR3
- 16 MB NAND
- RT3188 WLAN-Chip
- Push-switch to toggle DLNA / Miracast mode
There seems to be a UART available on some test points on the PCB. Any ideas on how to connect to that (settings)?
DLNA through BubbleUPnP is more or less working (skipping seems to lock the stick, playing playlists too), but Miracast is not, at least not on my Xperia L with CyanogenMod 11 / FXP 333.I tried the firmware for the "Pipo X5" and "MOCREO iPush M1" (both ~14MB) and both worked. Both state version "3.0.0-rc2". I would be thrilled if someone could link to a newer (and hopefully more bug-free) version than that...
EDIT: If found a link to a much better firmware (v5.0.0-rc2) for the CX-V3 here. DLNA is much better. Miracast still does not work, but I suppose that's just FXP 333...
if someone is interested this firmware allowed me to miracast with a samsung galaxy tab s
tried other firmwares (CR-M200,ugoos-ug017,CX-V3) but only this was updated
http://www.cloudnetgo.com/CR-M200S.htm
Regards
galaxy tab s
Hi Lucize,
I tried the firmware you posted, but the problem remains: "Impossible to initiate screen mirroring due to a HW problem"
What Android version do you have on your TAB S? Is it a 8.4 or 10.5 version?
Thanks in advance!
CR-M200 firmware on WiFi Display Dongle M806 on SM-G900V
lucize said:
if someone is interested this firmware allowed me to miracast with a samsung galaxy tab s
tried other firmwares (CR-M200,ugoos-ug017,CX-V3) but only this was updated
Regards
Click to expand...
Click to collapse
Thank you so much, lucize! It worked! I was able to miracast with my Galaxy S5 using the built in screen mirroring function. My android version is 4.4.4.
I got a Tronsmart CX-V3 dongle and I was wondering how to update it, since Tronsmart has -of course- no updates. So tried to find some more clones who could have an update and maybe even the manufacturer.
The latest I managed to find is version 9.0.0, dated 21-4-2015, by Ergotech. Their MD3054 and MD3056 seem to be the same according to the doc file in MD3054's update (8.0.0 rc1) (*1), so I downloaded MD3056's (*2) and flashed it. Sunchip-Tech strongly advices to update the software(*3), so i didn't have any hesitations.
A PDF included in 3056's update as well in the *3 link, indicates that there is OTA update option via the manufacturer (Sunchip-Tech). This means that maybe all Miracast sticks of this manufacturer can be updated directly by Sunchip-Tech. Keep in mind that the menu language will be switched to Chinese after the update, but it can be very easily switched back to English in the settings menu.
Ergotech's download page can be found in link *4.
While searching, I noticed than some RK2928 based Miracast dongles were called Lollipop (not because of Android). I searched a bit more and found Rockchip's user guide for RK2928 wireless HDMI dongles(*5), which calls RK2928 dongles as Lollipop. Seems that the reference Rockchip design is followed by the manufacturers. In that user guide I noticed the settings screen is same as my dongle's, but the main screen picture is different though same to some other RK2928/Lollipop dongles I had seen while searching. So probably there is an other manufacturer who kept the original main screen and maybe has even newer software. I did some more searching and the latest I could find is CloudNet's 3.21.00 (dated 28-5-2015) for CR-M200S. This one has OTA settings too, unveiling its manufacturer is Hotack. I believe it is a newer version than Ergotech's/Sunchip-Tech's version 9.0.0 because it has boot version 1.41 instead of 1.40.
CR-M200S download page is at link *6 and in lucize's post too.
Relatively new firmwares are also available by these companies:
Emtec (emtec-international.com/en-eu/Firmware-F100)
Ugoos (ugoos.net/A3S)
*1 drive.google.com/file/d/0B3bETZxL2iACYXdvV2VIdVh4dUU/view
*2 drive.google.com/file/d/0B3bETZxL2iACRXRZWndNRDRwZmM/view
*3 ergotech.com.tw/tw/newsdetail.aspx?id=106
*4 ergotech.com.tw/tw/Download_detail.aspx?key=
*5 upload.sunsky-online.com/res/drivers/S-EAT-0179.pdf
*6 cloudnetgo.com/CR-M200S.htm
talos_2002 said:
I did some more searching and the latest I could find is CloudNet's 3.21.00 (dated 28-5-2015) for CR-M200S. This one has OTA settings too, unveiling its manufacturer is Hotack. I believe it is a newer version than Ergotech's/Sunchip-Tech's version 9.0.0 because it has boot version 1.41 instead of 1.40.
CR-M200S download page is at link *6 and in lucize's post too.
*6 cloudnetgo.com/CR-M200S.htm
Click to expand...
Click to collapse
I can approve that the CR-M200S firmware you linked works quite well. Have you tried the OTA update too?
Latest firmware (MD3056PW 3/sept/15) is from ergotech. Version 10. However there is no dlna subtitle support yet. I am waiting for this firmware to appear soon. None of the firmwares support subtitles over dlna. There is a metadata code that can be used on the firmware to support subs. My nas network disk (twonky server) supports metadata as most do. I am using version 10 without any problems. The only other problem I have is my tablets resolution which is not supported, 1280x 800, which gives me black borders on the sides on the casting TV (when on landscape). I have tried all firmwares with the same result.
There is a metadata code in ezcast forum that they have used to display subtitles over dlna which I am not allowed to post.
Also I have managed to use kodi/xbmc to display videos over dlna but no subs support again. There is a YouTube video and files you need in order to accomplish this.
cypriot said:
Latest firmware (MD3056PW 3/sept/15) is from ergotech. Version 10. However there is no dlna subtitle support yet. I am waiting for this firmware to appear soon. None of the firmwares support subtitles over dlna. There is a metadata code that can be used on the firmware to support subs. My nas network disk (twonky server) supports metadata as most do. I am using version 10 without any problems. The only other problem I have is my tablets resolution which is not supported, 1280x 800, which gives me black borders on the sides on the casting TV (when on landscape). I have tried all firmwares with the same result.
There is a metadata code in ezcast forum that they have used to display subtitles over dlna which I am not allowed to post.
Also I have managed to use kodi/xbmc to display videos over dlna but no subs support again. There is a YouTube video and files you need in order to accomplish this.
Click to expand...
Click to collapse
I tried this vs the CR-M200S firmware, and the CR-M200S firmware is still the best imo. With my iphone that is the only one where mirroring works, and it seems to be less buggy.
Still awaiting a new better update than the CR-M200S . Youtube doesnt work with any of them!
have someone tried mirroring wich this device on wp 8.1?
lokura said:
have someone tried mirroring wich this device on wp 8.1?
Click to expand...
Click to collapse
I also have the same problem. WiDi of windows 8.1 (with supported hardware) does not work with the Chinese miracast dongle RK2928. I get the message:
Your HD digital display device did not supply the required identification data (EDID)
I found this site from sunchip, they say its workin on win 8.1 http://www.sunchip-tech.com/prod_view.aspx?TypeId=12&Id=71&FId=t3:12:3
on the screen captures you can see the firmware versión is 6.0.0 rc3, Im looking for it now in order to test.
working on wp 8.1 witch the soft from ugoos.net/A3S
lokura said:
working on wp 8.1 witch the soft from ugoos.net/A3S
Click to expand...
Click to collapse
Thanks. I will try this too.
I was able to test ergotech v10 firmware. After extensive tests It only worked with WIDI 3.5.41.0 driver. None of the latest intel WIDI drivers worked.
I will try to install ugoos firnmware to see if it works with latest intel WiDi drivers.
Thanks.
Update
Ugos A3S does not work on my Lenovo T420 laptop and Widi Intel 4.3.4.0 (((( I get the same message as before.
Update:
No firmware works with latest WiDi driver.
The only WiDi driver which works with any rk2928 firmware (I tried 3 firmwares) is 3.5.41.0.
Hardware:
Intel i5-2520M VPro
Intel Processor Graphics 3000 HD
Intel Centrino Ultimate-N 6300 WiFi
Drivers
Graphic 9.17.10.4229
Wireless: 15.18.0.1
Software
WiDi application 3.5.41.0 installed 4.3.4.0 recommended (by intel widi update tool but is not working)..
The rk2928 firmware is miracast dlna airplay compatible, without any subtitle support over dlna.
For summary if you want widi support under windows 8 (8.1) then for me only intel widi 3.5.41.0 driver is working.
Also if you want dlna support under windows 8.1 it is possible. Samsung did produce a allshare excellent application which they have now discontinued, and is working like charm under windows 8.1.
Search google and download the Samsung allshare with version: 2.1.0.12031.10 (also called 2.1.0.12031_10)
Last point. For me ergotech V10 is the best firmware on Rk2928 dongle (as I have tested. My dongle used to display a connection name: lollipop)
ios9 airplay
Since ios9 update on iphone Airplay does not work on these dongles any more! and none of the firmware.
The latest firmware located on the ergo-tech website (ergotech.com.tw/tw/Download_detail.aspx?key= firmware v.11.0.0 and 3.0.0 here) claims that it supports ios9, but i have tried ios9.0.2 and 9.1 on these with iphone and it does not work.
Does anyone know a way of getting ios9 airplay to work?
There is a RK2928 dongle which claims to have ios9 support, the Visonicom RealCast VMD-RK156 realcastptv.com/tag/WiFi-display-dongle-Rockchip-RK2928) but i cannot find a firmware download for it.
Kabeern said:
Since ios9 update on iphone Airplay does not work on these dongles any more! and none of the firmware.
The latest firmware located on the ergo-tech website (ergotech.com.tw/tw/Download_detail.aspx?key= firmware v.11.0.0 and 3.0.0 here) claims that it supports ios9, but i have tried ios9.0.2 and 9.1 on these with iphone and it does not work.
Click to expand...
Click to collapse
Firmware 3.0 disables the wifi. So it does not work.
Firmware 11 has problem with the quality. Frames are skipping and video picture gets distorted.
I have tested firmware 11 extensively it is has flaws in video quality. Only ergotech firmware 10 works flawlessly.
I am back on firmware 10.
Tested hardware: miracast rk2928, Lenovo T420 with windows 8.1, intel HD 3000 graphics card, and widi 3.5.41.0 and intel centrino ultimate N-6300 and KODI (xbmc)..
Dear Friends I am in ingrate and desperate situation, I have a briked device m806 black one with antenna, I have Prepare IDB Fail no boot and i try 50 time to flash nothing,I make 2pin shortcut and I have blue square in RK BATCH TOOL 1.7 ,but when i push RESTORE button IDB fail erorr continous! Any advice please,I have a briked device!
alesul said:
Dear Friends I am in ingrate and desperate situation, I have a briked device m806 black one with antenna, I have Prepare IDB Fail no boot and i try 50 time to flash nothing,I make 2pin shortcut and I have blue square in RK BATCH TOOL 1.7 ,but when i push RESTORE button IDB fail erorr continous! Any advice please,I have a briked device!
Click to expand...
Click to collapse
If you are using Windows 8.1 or 10, try flashing your device with windows 7.
I try with 7 and nothing!
any help???
HI. ( Sorry for my english )
My device M8S is tottaly bricked. Until the brick this device looged to google store, google loged this device as SkyKirin MS8. ( AMLOGIC S812 2g/8g)
I need firmware for this device ,i dont remember everting , but i looking android settings it seems to me i fund "SkyKirin and "n200".
I flash in sdcard megatron firmware for m8s and ms9 , work fine , but wifi not work, and see only 4gb.
I decided to flashing other firmwares , there is results :
20150129-eny-m8s.zip - no wifi , remonte control ok , power off not working
acemax M8S_0313_0602 kodi 14.2 - no wifi , remonte control buttons reversed.
m8s_ap6330_8g2g_150818_USB - no wifi, no ethernet, no remonte control......
KoDi_EM8S_eng_1114_20150123 - no wifi...j dont remember what else not working
All this firmwares see only 4gb ram :/
DEVICE M8S 2G/8G
NAND (SK Hynix H27UCG8T2ETR BC) 8G
WIFI AP6330
Does anybody know how to modify the Megatron-S812-M8S-M9 rom to see 8 gb and wifi working ? Then it to be perfect.
Same problem here.... :/
same issue i have
For un bricking theses device's it may be worth taking a look here http://freaktab.com/forum/tv-player-support/amlogic-based-tv-players/s802/eny-acemax-ott/knowledge-tutorials/553667-how-to-unbrick-amlogic-s805-s802-s812-s905-video-tutorial
Did you guys every resolve this?
DEVICE M8S 2G/8G (SkyKirin/n200)
WIFI AP6330
MBX/n200/n200:4.4.2/KOT49H/20160706:user/test-keys
I own the Bqeel 2019 Android 8.1 TV Box Y4 MAX / Amlogic S905X2 Quad Core / 4G DDR4+64G eMMC / Dual WIFI 2.4/5.8G + 100M LAN / tv box Bluetooth 4.0 / USB 3.0/ HDMI 2.1 /4K Smart TV Box .
I have tried many custom roms and none of them seem to work in the correct manner. I am able to use the latest USB burning tool but lot of these custom roms will flop on me after the install process. I feel like there is something usually wrong with the WIFI side. if it is not a wifi problem, then it is the remote control.
I have yet to find a custom rom where I can load and then use the device the way it is suppose to be. I want the remote to work correctly. Keep in mind that I do have a direct Ethernet connection for this device.
I have contacted the original manufacturer hoping that they can send me the original default firmware.
Back to the topic, i am interested in the best, the latest, and the one the works the most for this device. All solutions have failed for me thus far.
ps: i will re try the following .img files that I was able to obtain from FreakTabs
- XTM_ATV_X96_4_4 (this one will not connect to the internet directly. it needs a cell phone or tablet, so i can transfer over the Wifi and Google Account settings. For some reason, this is impossible because it keeps asking for my WIFI password which i have entered many times in the device);
- Poison_S905x2_V2.0 (this one is easy to install but after the install, the GUI seems stuck. I can't open up any apps, and the weather icon is always spinning).
Again, i have tried maybe 5 different custom roms from freaktabs (i am sure they are posted here) and none of them seem to work.
Hello , i have same issue here
i flashed many times with many roms and no one work properly.
Sometimes i have no wifi/ethernet or no remote.
please if someone have the stock firmware of Bqeel y4 max 905x2 4/64go
Post it!!
really sorry for my english
alilous1000rr said:
Hello , i have same issue here
i flashed many times with many roms and no one work properly.
Sometimes i have no wifi/ethernet or no remote.
please if someone have the stock firmware of Bqeel y4 max 905x2 4/64go
Post it!!
really sorry for my english
Click to expand...
Click to collapse
I have the same problem.
I have tried many custom roms but nothing seems to work. Wifi and Bluetooth issues is a problem.
I too need STOCK firmware. I have extra device that is not been messed around with but i do not know how to make back up from stock rom. If i can make stock up rom with one app, i will do it ASAP and perhaps share it.
Edit: So I am able to obtain a back up of the stock firmware via Twrp from my second device, but it is not compatible with the other Bqeel system. All i see is the Bqeel Boot Logo.
I am still able to boot into recovery, and i can also install other custom roms (those custom roms stink).
I still need the orgiinal stock firmware in .img or i need a custom rom that actually works really great.
For those who want to purchase this device, you can but do not mess with custom roms. Just remove default apps and enjoy the default OS.
I contact the seller of my box (bqeel y4 max 4/64go) today
he gonna send me the stock firmware Asap.
I 'll share it when i 'll recieve it.
Thanks
alilous1000rr said:
I contact the seller of my box (bqeel y4 max 4/64go) today
he gonna send me the stock firmware Asap.
I 'll share it when i 'll recieve it.
Thanks
Click to expand...
Click to collapse
I did the same thing. They sent me the stock firmware. the device works great now! there is another hiccup though. For usb burning tool, you will need some license files. when you load the .img file in the program, it will not accept it. You need the license files (just transfer them in the directory in usb burning tool)
here is the link for license files and stock firmware.
https://mega.nz/#F!TvoShAAK!Jd0X15aoHWVdOf1rrYPc0g
I tried that firmware in my box and it freezes on logo!!!
any news for this device? I have tried many custom OS but none work due to missing drivers.
LooseEnd85 said:
I did the same thing. They sent me the stock firmware. the device works great now! there is another
Click to expand...
Click to collapse
What did you actually wrote into the message? I'm in touch with them since a few days but I cannot go over than "we can replace the unit"!
BTW, my Device Build Fingerprints: Amlogic/u211/u211:8.1.0/OPM1.171019.011/20190402:user/release-keys
Bqeel 2019 Android 9.0 TV Box Y4 MAX / Amlogic S905X2 Quad Core / 4G DDR4+64G eMMC / Dual WIFI 2.4/5.8G + 100M LAN / tv box Bluetooth 4.0 / USB 3.0/ HDMI 2.1 /4K UHD Smart TV Box
Yes... it should have android v9 but it's a v8.1... I found the error when the Amazon return window was already closed...
https://www.bqeel.net/download.html
There are firmwares from bqueel
Hi
Can somebody now tell me if firmware from bqeel.net works or not becuse I've seen a loot that say it's stuck at logo screen or it won't boot
Does it work or no?
so far the best custom ATV ported ROM I've found for this box is here: https://forum.freaktab.com/forum/tv...ionatv__bqeel_u214-y8_max_1000m_s905x3-test57
it is due for an update but works as is. I also have a SlimBox ROM that works for the Bqeel but I'll have to upload that to my Mega folder and share the link.
EDIT: nevermind my boxi s the Y8 Max this is asking for the Y4 Max,.