Hi Friedns,
During the unbrick process of my LG G3 d851 T-Mobile, I mistakenly flash the sbl1 partition before flashing any other partitions (using the "BoardDiag_v2.99a_modified_by_willcracker" ), my phone turned on (showing battery with exclamation sign). Now, I'm unable to repair it, I'm too much worried and wasted a month or so while searching the solution. Please help me to get back to previous state sothat I can flash partitions in right sequence.
Thanks in advance.
musmanzulfiqar said:
Hi Friedns,
During the unbrick process of my LG G3 d851 T-Mobile, I mistakenly flash the sbl1 partition before flashing any other partitions (using the "BoardDiag_v2.99a_modified_by_willcracker" ), my phone turned on (showing battery with exclamation sign). Now, I'm unable to repair it, I'm too much worried and wasted a month or so while searching the solution. Please help me to get back to previous state sothat I can flash partitions in right sequence.
Thanks in advance.
Click to expand...
Click to collapse
Sorry to hear that, you would need to flash the entire firmware again.
I personally use the LGUP tool, you can download it here https://www.mylgphones.com/download-lg-up-software
Next, you would need to find the .kdz firmware of your phone. Try searching on google for it, it should be around 1gb file. Flashing that stock firmware should repair your phone.
Thanks for reply bro.
Unfortunately no software is detecting my device.
It's just appearing as "LGE androidnet usb serial port" in device management.
How could I unbrick in this situation.
musmanzulfiqar said:
Thanks for reply bro.
Unfortunately no software is detecting my device.
It's just appearing as "LGE androidnet usb serial port" in device management.
How could I unbrick in this situation.
Click to expand...
Click to collapse
Is your device in download mode? It has to be in download mode, then you can use LGUP to download the firmware.
Device is completely off, not turning on, no recovery mode and no download mode. Screen just turns on when connected to PC without battery and then shows sign of exclamation.
musmanzulfiqar said:
Device is completely off, not turning on, no recovery mode and no download mode. Screen just turns on when connected to PC without battery and then shows sign of exclamation.
Click to expand...
Click to collapse
Hi , maybe this can help you:
https://www.google.rs/amp/www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/amp/
Related
Need urgent Help with wrong nand restore of LG-F160 "K" variant on its "S" variant
Hi dear helpers,
I got a phone (LG-F160S ) for my girl friend. I already have my own same rooted phone but of " K " variant.
I rooted and installed cwm recovery on her "S" variant, and nand restored her S phone with my K back up.
Now the phone boots, giving "Security error" under LG logo. Situation now is:
>It goes to "LG repair service mode", gets detected as adb device and adb works.
>Goes to "download mode" but doesn't get detected at all, not even a device attached sound on windows, as if nothing has been connected to Pc. Download mode just stays there as if hung and stuck. So can't flash Kdz
> have tried different computers and different data cables but no luck.
> My own K variant with same computer setup and drivers gets detected properly on download mode, but that victimized " S " variant shows no signs of connectivity, although it works and responds to Adb from "Lg service repair mode ".
Now please tell me what do I do next to revive phone? I think the wrong boot.img has been restored. SO may be need to somehow flash appropriate boot.img via Adb.??
Help please you all Nice helpers....
Sent from my LG-F160 using Tapatalk 2
Sent from my LG-F160 using Tapatalk 2
having same problem with 2 lg phones but no help came out. yet!!
salman1497 said:
Hi dear helpers,
I got a phone (LG-F160S ) for my girl friend. I already have my own same rooted phone but of " K " variant.
I rooted and installed cwm recovery on her "S" variant, and nand restored her S phone with my K back up.
Now the phone boots, giving "Security error" under LG logo. Situation now is:
>It goes to "LG repair service mode", gets detected as adb device and adb works.
>Goes to "download mode" but doesn't get detected at all, not even a device attached sound on windows, as if nothing has been connected to Pc. Download mode just stays there as if hung and stuck. So can't flash Kdz
> have tried different computers and different data cables but no luck.
> My own K variant with same computer setup and drivers gets detected properly on download mode, but that victimized " S " variant shows no signs of connectivity, although it works and responds to Adb from "Lg service repair mode ".
Now please tell me what do I do next to revive phone? I think the wrong boot.img has been restored. SO may be need to somehow flash appropriate boot.img via Adb.??
Help please you all Nice helpers....
Sent from my LG-F160 using Tapatalk 2
Sent from my LG-F160 using Tapatalk 2
Click to expand...
Click to collapse
actually I was trying to unbrick these devices having same but some different issues, 1st one goes to download mode but pc doesn't recognize my phone as there is nothing attached to it, while the other one have nothiing!! no recovery no download mode no nothing, just Lg logo with consistent restarts and no detection. Maybe there is a solution or maybe not, But I need to know for sure!!
Note!! everything in hardware is good the problem only occurred when these phones were being rooted..
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
I have the same problem help!!!
LoToR122 said:
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
Click to expand...
Click to collapse
No responses to Emergency mode flashing by KDZ?
Try at least with HARD RESET... Hold Power Key + Volumen Down key + Home key
When LG logo appears, release all the keys! Good luck!
LoToR122 said:
My LG D605 does not boot and I have a black screen. Before brick i go via ADB to recovery on official KK. Mobile is dead USB dont work
Click to expand...
Click to collapse
Give me a pm when you have 1 hour I might have an idea to save you.
christi9503 said:
Give me a pm when you have 1 hour I might have an idea to save you.
Click to expand...
Click to collapse
Can you help me? pls
kikobuendia said:
I have the same problem help!!!
Click to expand...
Click to collapse
First, there is no such thing as hardbrick (not anymore, most modern phones cant be hardbriked )
Be sure, u have all the drives and whatnots installed in the copmuter !
from: http://forum.xda-developers.com/showthread.php?t=2730501
[Q] How to install a .kdz?
[A] (Tutorial thanks to @[W]ar[H]ead, confirmed working by TaZRAge)
#1) First to get into download mode:
1. Remove battery
2. Put usb to computer and phone (w/o battery)
3. Hold "Vol up" button
4. Put battery back
You will get into download mode (aka emergency mode).
#2) Unpack kdz flasher, and install msxml.msi.
#3) Run KDZ_FW_UPD.exe set "type" to 3GQCT and "phonemode" to DIAG.
#4) Choose the .kdz file to flash. Download link is under the "Downloads"
#5) Click "Launch software update" and wait. Phone must be connected in download mode(!). KDZ installer might get stuck but DO NOT disconnect it. (Unless it stays that way for a hour as a example)
NOTE: .kdz is a .kdz, you cannot extract it. If you get a .zip from the LG .kdz site you did something wrong.
Cisf said:
First, there is no such thing as hardbrick (not anymore, most modern phones cant be hardbriked )
Be sure, u have all the drives and whatnots installed in the copmuter !
from: http://forum.xda-developers.com/showthread.php?t=2730501
[Q] How to install a .kdz?
[A] (Tutorial thanks to @[W]ar[H]ead, confirmed working by TaZRAge)
#1) First to get into download mode:
1. Remove battery
2. Put usb to computer and phone (w/o battery)
3. Hold "Vol up" button
4. Put battery back
You will get into download mode (aka emergency mode).
#2) Unpack kdz flasher, and install msxml.msi.
#3) Run KDZ_FW_UPD.exe set "type" to 3GQCT and "phonemode" to DIAG.
#4) Choose the .kdz file to flash. Download link is under the "Downloads"
#5) Click "Launch software update" and wait. Phone must be connected in download mode(!). KDZ installer might get stuck but DO NOT disconnect it. (Unless it stays that way for a hour as a example)
NOTE: .kdz is a .kdz, you cannot extract it. If you get a .zip from the LG .kdz site you did something wrong.
Click to expand...
Click to collapse
You don't know what you are saying. You can HARDBRICK ANY modern device. By definition hardbrick means phone won't turn on won't respond and in some cases recognized as usb when connected to pc as usb bulk or qcom usb. etc. You damage the second bootloader and tell me what happens. You will see what you get.
christi9503 said:
You don't know what you are saying. You can HARDBRICK ANY modern device. By definition hardbrick means phone won't turn on won't respond and in some cases recognized as usb when connected to pc as usb bulk or qcom usb. etc. You damage the second bootloader and tell me what happens. You will see what you get.
Click to expand...
Click to collapse
first this is offtopic. Second, u are wrong ! Unless the phone is pshisicaly damaged (misfuctioning components or damaged), u cant hardbrick the phone with uploading different soft. on it (unless u change voltages and overclok, if that is possible on the device). Ofecourse they are exceptions, but all major modern manufactors, make hardbrick proof devices. Also, how exactly would u modify the emergency mode, and more important even if you could, why wold u do it !?
More on to the topic, none of the operations of rooting, bootloader installing, kdz install or CMx install , gets near the emergency mode. It remains intact.
Just retry all normal steps for installing kdz or recovery again, check the cables, all drivers on pc, and is best to have a charged phone battery.
EDIT: @kikobuendia
i found this post, same operations as mentioned in first reply, but more detailed:
http://forum.xda-developers.com/opt...optimus-l9-ii-lg-d605-unroot-unbrick-t2964693
Cisf said:
first this is offtopic. Second, u are wrong ! Unless the phone is pshisicaly damaged (misfuctioning components or damaged), u cant hardbrick the phone with uploading different soft. on it (unless u change voltages and overclok, if that is possible on the device). Ofecourse they are exceptions, but all major modern manufactors, make hardbrick proof devices. Also, how exactly would u modify the emergency mode, and more important even if you could, why wold u do it !?
More on to the topic, none of the operations of rooting, bootloader installing, kdz install or CMx install , gets near the emergency mode. It remains intact.
Just retry all normal steps for installing kdz or recovery again, check the cables, all drivers on pc, and is best to have a charged phone battery.
EDIT: @kikobuendia
i found this post, same operations as mentioned in first reply, but more detailed:
http://forum.xda-developers.com/opt...optimus-l9-ii-lg-d605-unroot-unbrick-t2964693
Click to expand...
Click to collapse
I am not gonna reply again but I am just saying you have no idea. Do not talk unless you are sure you can hardbrick any device with just root and just writing on second bootloader partition. Read about it if you don't know. Do not argue about it.
I can't get into download mode
kikobuendia said:
I can't get into download mode
Click to expand...
Click to collapse
Then that's a hard brick pretty much. Pull the battery out and connect the phone to PC. Tell me if it gets recognized.
EDIT: OFC wait like 6 seconds then put it back and after that connect to USB.
When i connect it pc makes a sound
kikobuendia said:
When i connect it pc makes a sound
Click to expand...
Click to collapse
I don't care if it makes a sound or not it's like it gets recognized? Look into device manager.
christi9503 said:
I don't care if it makes a sound or not it's like it gets recognized? Look into device manager.
Click to expand...
Click to collapse
Yes but flashtool doesnt recognize it
kikobuendia said:
Yes but flashtool doesnt recognize it
Click to expand...
Click to collapse
If you want to get this fixed just listen to me. It won't work like this tell me the answers to my questions and we might solve your problem. What is your device recognized as. Make me a screenshot of device manager if you can't explain.
neutrondev said:
Then that's a hard brick pretty much. Pull the battery out and connect the phone to PC. Tell me if it gets recognized.
EDIT: OFC wait like 6 seconds then put it back and after that connect to USB.
Click to expand...
Click to collapse
I have the same probalem, cant get to download mode, when i connect to pc it recognise it in hs usb qdloader 9008, any solutions to fix it. I flashed wrong .tot file.
did you managed to unbricked it?
I have the same probalem, cant get to download mode, when i connect to pc it recognise it in hs usb qdloader 9008, any solutions to fix it. I flashed wrong .tot file.
Click to expand...
Click to collapse
No, no luck yet. Seems to be impossible.
I connect to this post cuz my d605 is also facing a similiar issue, no system, no recovery, no adb, download mode worked only twice, for the rest, only emergency mode works, phone cannot even charge.
Phone is recognized from pc, I uninstalled modem drivers but stays in Emergency only few seconds then it shuts down (not sure if its the battery, since it doesn't charge as well). It shuts down actually at the moment that LG mobile support tool seems to recognize it.
It worked couple of times, phone was keeping staying in emergency mode for the beginning of the procedure but at the moment it need to put the kdz into the phone, the phone die.
The two times download mode worked, same, just shutting down immediately. This with LG support tool or LG flashtool2014.
KDZ_FW_UPD worked the first time after install and then doesn't run anymore, on two different Win10 machines.
I have no idea how to come out of this nightmare, just want to flash it :/
Ag0n1a said:
I connect to this post cuz my d605 is also facing a similiar issue, no system, no recovery, no adb, download mode worked only twice, for the rest, only emergency mode works, phone cannot even charge.
Phone is recognized from pc, I uninstalled modem drivers but stays in Emergency only few seconds then it shuts down (not sure if its the battery, since it doesn't charge as well). It shuts down actually at the moment that LG mobile support tool seems to recognize it.
It worked couple of times, phone was keeping staying in emergency mode for the beginning of the procedure but at the moment it need to put the kdz into the phone, the phone die.
The two times download mode worked, same, just shutting down immediately. This with LG support tool or LG flashtool2014.
KDZ_FW_UPD worked the first time after install and then doesn't run anymore, on two different Win10 machines.
I have no idea how to come out of this nightmare, just want to flash it :/
Click to expand...
Click to collapse
well, sorry for not replying earlier. My phone was on guarantee for about 2 months after I wrote the post. I just send it to LG Hellas via the e-shop I bought it from and in about 2-3 weeks, I had my D605 back like it was brand new. I searched a lot about my D605 hard bricked and I found that it is not fixable. My phone could not go into download mode though, as yours. Hope I helped you even a lil bit. Sorry for my bad English.
Problem Description
1.LG G2 stuck at boot logo.
2.Cannot enter download Mode
3.Stuck at factory reset screen (factory reset processing) and cannot enter RECOVERY
4.cannot enter fastboot mode
5.Phone not detecting in your computer either windows or linux!
6.Cannot enter qhsusb mode.
7.Gone to service centre and they said to replace motherboard and u hav no warranty!
[ As stated by dear friend kryptonite
THIS METHOD WONT WORK IF YOU ARE STUCK IN QDLOADER 9008 MODE.(PHONE CONNECTED TO PC SHOWS SERIAL PORT).
(For you guys,there seems to be no options as of now.You will have to replace motherboard or wait for JTAG support.IF any of you need me to try to find a method you are welcome to sent your device to me so i can check it out.) ]
This can occur when flashing wrong images to the partitions when in qhsusb mode.
IF YOU CAN ENTER QHSUSB MODE [BLACK SCREEN BOOT] THEN FOLLOW THIS TUTORIAL
http://forum.xda-developers.com/show....php?t=2582142
Only solution for you guys is the following..
[THIS SOLUTION IS EASY BUT NEEDS YOU TO MESS WITH THE MOTHERBOARD.BUT SOLUTION DOESNOT REQUIRE HARDWARE SERVICE SKILLS.THE ONLY OTHER SOLUTION FOR YOU GUYS IS TO CHANGE THE MOTHERBOARD.SO THIS WIL BE YOUR ONLY CHOICE.]
1. For that you have to contact me...........
dear op, i have d802. my foolishness, i flashed d800 software on it.now it stuck in boot loop.i can factory reset the phone but of no use. phone can be booted in download mode but it is not detected by pc.although it is detected by windows when in boot loop, lg android net modem all shows but in download mode, nothing is detected.
as it is not detected in download mode, i can not flash anything.it is also not detected in ubuntu.
need help and advice regarding this what to do now.
hahmad78 said:
dear op, i have d802. my foolishness, i flashed d800 software on it.now it stuck in boot loop.i can factory reset the phone but of no use. phone can be booted in download mode but it is not detected by pc.although it is detected by windows when in boot loop, lg android net modem all shows but in download mode, nothing is detected.
as it is not detected in download mode, i can not flash anything.it is also not detected in ubuntu.
need help and advice regarding this what to do now.
Click to expand...
Click to collapse
The next step I'd try is using a different computer if possible. I've had similar issues before, but it turns out my old laptop just didn't like my phone.
shubh2007 said:
[ As stated by dear friend kryptonite
THIS METHOD WONT WORK IF YOU ARE STUCK IN QDLOADER 9008 MODE.(PHONE CONNECTED TO PC SHOWS SERIAL PORT).
(For you guys,there seems to be no options as of now.You will have to replace motherboard or wait for JTAG support.IF any of you need me to try to find a method you are welcome to sent your device to me so i can check it out.) ]
This can occur when flashing wrong images to the partitions when in qhsusb mode.
I.
Click to expand...
Click to collapse
Just FYI - this is an incorrect statement. I myself had a QHUSB 9008 error and it was fixed REMOTELY (using TeamViewer) using a special software called BoardDiag by some members on this board (like Tungkick). It does cost 20-30$ though, but the G2 is one of the most repairable phones I have seen
asdfvtn said:
The next step I'd try is using a different computer if possible. I've had similar issues before, but it turns out my old laptop just didn't like my phone.
Click to expand...
Click to collapse
have tried 3 different pc, windows xp, 7 32 bit, 64 bit, even 12.10 ubuntu
---------- Post added at 10:42 PM ---------- Previous post was at 10:34 PM ----------
i tried to go for short capacitor method too, but as i attach data cable, pc detecte lg virtual modem and lg blue tooth modem. confused what to do now
Phone is bricked, any help would be appreciated. I downloaded a loader.img from a russian forum but am not sure about how to load the same via memory card.
I read about loading a TOT file but cannot find the same
Download your firmware from here http://lg-phone-firmware.com/firmware-LG+L65-Tutti-50.html
Then follow the thread http://forum.xda-developers.com/showthread.php?t=2797190
GreekDragon said:
Download your firmware from here http://lg-phone-firmware.com/firmware-LG+L65-Tutti-50.html
Then follow the thread http://forum.xda-developers.com/showthread.php?t=2797190
Click to expand...
Click to collapse
Already tried this, does not connect
Any other method please
silhouette said:
Already tried this, does not connect
Any other method please
Click to expand...
Click to collapse
Are you sure that you following the steps carefully?
What it shows?
GreekDragon said:
Are you sure that you following the steps carefully?
What it shows?
Click to expand...
Click to collapse
I have attached screenshot
Phone basically does not connect to software
Only software that connects is Medusa professional tool. The 'easyrepair' function completes but phone does not turn on.
Shows in device manager as 'qualcomm hs-usb qdloader 9008'
silhouette said:
I have attached screenshot
Phone basically does not connect to software
Only software that connects is Medusa professional tool. The 'easyrepair' function completes but phone does not turn on.
Shows in device manager as 'qualcomm hs-usb qdloader 9008'
Click to expand...
Click to collapse
Try with other USB Cable and ports.
Try with another PC.
GreekDragon said:
Try with other USB Cable and ports.
Try with another PC.
Click to expand...
Click to collapse
Tried on two win7 PCs, now will give a try on an XP PC
Thanks
Tried different PCs and operating systems. Process stops at 60% in emergency mode, in DIAG mode phone does not connect
GreekDragon said:
Try with other USB Cable and ports.
Try with another PC.
Click to expand...
Click to collapse
http://4pda.ru/forum/index.php?s=&showtopic=627989&view=findpost&p=36483576
This post says something about loading a loader image via external sd card
Has anyone tried this, I have a loader.img for l65 d280n but was not able to revive phone
http://4pda.ru/forum/index.php?showtopic=627989&st=440#entry36483576
I followed above procedure loaded loader.img from a 4gb memory card
Now I can again get to download mode. But update fails at 15%
Phone screen shows 'rooted' in red; is this reason for update fail? Screenshot attached
silhouette said:
http://4pda.ru/forum/index.php?s=&showtopic=627989&view=findpost&p=36483576
This post says something about loading a loader image via external sd card
Has anyone tried this, I have a loader.img for l65 d280n but was not able to revive phone
Click to expand...
Click to collapse
Post please here loader.img for d280n. Thank you.
Posting as a guest to add my experience with unbricking an LG-D280n phone...
My phone bricked when allowing an online software update from LG. The phone froze on the startup logo for hours, and download menu could not be entered, just the fatal error pink screen was displayed. LG service centre said they couldn't fix it, the online instructions using LG Flash Tool 2014 or BordDiag v2.99 wouldn't help, but then I came across the YouTube video 'LG L65 D285 DBI Err Fatal' by VARAN500. Yes, it is in Russian, no, I don't speak Russian, but it is simple enough
Treat your LG phone as a removable drive, connected via USB to a PC with the LG USB driver and the LG Mobile Support Tool installed.
In my case, when the LG phone displayed the pink screen, it also showed as a removable drive (with a 4GB disk) on the connected PC. Follow the insructions in the video for a low-level quick format of that 4GB disk, re-format it as FAT32, then write the abovementioned loader.img to that drive. Disconnect the battery, and you should now be able to go into download moade, from which you can either use the official LG app or Flash Tool with a .kdz image to re-write the firmware to your phone.
A few restarts and (irrelevant?) error messages later, my phone was working again, and to my amazement, all my data and settings were still there too!
Hope that helps other who might be in the same sitation as I was.
hi
silhouette said:
Phone is bricked, any help would be appreciated. I downloaded a loader.img from a russian forum but am not sure about how to load the same via memory card.
I read about loading a TOT file but cannot find the same
Click to expand...
Click to collapse
does anyone have a solution for this particulare phone i wont to fix this phone
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse