Related
I'm trying to figure out if my Edge is bad. When I turn the screen off, and come back to the phone a few minutes later, I'll get a notification stating it has connnected to my router. I've checked the settings and it states the wifi is set to be always on. I attempted a factory reset and still no luck. Sometimes it'll take a few moments before it even connects to the wifi again upon turning the screen on.
Do I have a bad phone?
vaxick said:
I'm trying to figure out if my Edge is bad. When I turn the screen off, and come back to the phone a few minutes later, I'll get a notification stating it has connnected to my router. I've checked the settings and it states the wifi is set to be always on. I attempted a factory reset and still no luck. Sometimes it'll take a few moments before it even connects to the wifi again upon turning the screen on.
Do I have a bad phone?
Click to expand...
Click to collapse
I would check under the advanced settings for wifi, there's an option for what to do with wifi during sleep. That may be your problem.
I've already checked and it''s enabled.
vaxick said:
I've already checked and it''s enabled.
Click to expand...
Click to collapse
I have the same thing happening. I noticed when I was backing pics on one drive
. It would always say that back up has stopped because there was no WiFi After turning the screen on again.
I just got my Edge yesterday, and I am having the same problem with wifi AND also that it stops seeing any wifi and I have to toggle it off and back on manually THEN it will instantly connect to my known network.
Dear @vaxick,
Dial *#0011# and click on more>>WiFi>>"WIFI Power save mode" try to disable this option and see what happens.
*it might drain your battery faster.
Regards
bluff master said:
Dear @vaxick,
Dial *#0011# and click on more>>WiFi>>"WIFI Power save mode" try to disable this option and see what happens.
*it might drain your battery faster.
Regards
Click to expand...
Click to collapse
Thank you for this suggestion, unfortunately it had no effect as I have observed the same wireless disconnect behavior now with both the WiFi power save both on and off. Once the wireless disconnects it no longer see ANY wireless networks no matter where I go until I toggle the wireless off then back on again. Then it will see all wireless network present around me and instantly connect if there are any of my saved networks present. At this point I believe it is either a hardware or worse a software problem with my phone, but I am really at a loss to the exact nature of this issue.
Mine also has this issue when connected to 5GHZ SSID. Connecting to my 2.4GHZ SSID solves this problem completely for me
dazbutler1 said:
Mine also has this issue when connected to 5GHZ SSID. Connecting to my 2.4GHZ SSID solves this problem completely for me
Click to expand...
Click to collapse
I hope that this is a hardware issue with my phone, as your "solution" is totally unacceptable for me, especially since my work place has bandsteering AP's that use the same SSID's for both 2.4 and 5GHz.
Moguledyouth said:
I hope that this is a hardware issue with my phone, as your "solution" is totally unacceptable for me, especially since my work place has bandsteering AP's that use the same SSID's for both 2.4 and 5GHz.
Click to expand...
Click to collapse
Yeah, i have to turn WIFI off whilst at work for the same reason. Certainly hoping it's just a software bug and will be fixed quickly as it is by no means an ideal workaround
I also see this kind of problem since last 1 week, here is how i noticed. i user viber messaging app and it shows status online if you are connected. Lot of my friends started complaining that my status is not continuously online and fluctuating so i started doing tests.
Moment my display turns off i started counter and in 10 minutes my status changes as last seen and whenever i open viber app again i am online.
second test: i tried doing the same with whatsapp and connected at web.whatsapp.com and same thing happens within 10 mins i see yellow bar appearing that my phone is disconnected so again i have to open whatsapp on phone to reconnect.
this is very annoying to see this kind of problem on new phones, especially when old phones are working flawless.
Kind of the same problem, but with GPS. Once I disabled the battery saver mode, it stopped disconnecting. Have you tried that?
Are you referring to power saving mode in battery settings. i did check and they are turned off. No idea what else i am missing here.
I tried re-installing viber but still after 10 mins its keep disconnecting.
WiFi >> More >> Keep WiFi on during sleep >> Always
Problem solved
Sent from my SM-G925F using XDA Free mobile app
vvally said:
WiFi >> More >> Keep WiFi on during sleep >> Always
Problem solved
Sent from my SM-G925F using XDA Free mobile app
Click to expand...
Click to collapse
I'm having the same issue on my regular non edge s6. This settings is not doing anything have it on always still always drops the wifi when going to sleep. Its driving me crazy no idea why its doing this
i did check and i have Keep WiFi on during sleep >> Always option but still drops, no clue whats wrong with my phone.
I had the same issue and solved it by changing my routers security from WPA2/Mixed Mode to WPA2 Personal. Since this change, it works fine on both 2.4 ghz and 5 ghz.
dazbutler1 said:
Yeah, i have to turn WIFI off whilst at work for the same reason. Certainly hoping it's just a software bug and will be fixed quickly as it is by no means an ideal workaround
Click to expand...
Click to collapse
I received my Galaxy S 6 edge a week ago and I am having this same peculiar reconnecting issue to WiFi that has been described here.
Solution?
I was having this same issue and was unable to find any good solutions for it online, but eventually found something for me that worked through experimenting:
Find the above mentioned "Keep Wi-Fi on during sleep" option (which is probably set to "Always" already), change it to "Never", and then change it back to "Always". Since doing this I haven't had it disconnect from the wi-fi once, where as before it would do it everytime the screen had been off for a few minutes.
The problem started happening sometime after I played with power saver mode, so I think it might be related to that. I know that the software has some other bugs related to power saving mode, as I had a previous problem where my softkeys stopped vibrating or lighting up, which ended up being related to not exiting ultra power saving mode correctly and was fixed by going re-enabling ultra power saving mode and exiting again.
My wife and I both have the problem of our wifi always turning on. I've turned off every conceivable thing I can think of so the wifi stays off, but it randomly keeps turning on. Anyone else experiencing this?
kawika0 said:
My wife and I both have the problem of our wifi always turning on. I've turned off every conceivable thing I can think of so the wifi stays off, but it randomly keeps turning on. Anyone else experiencing this?
Click to expand...
Click to collapse
No for me you should try restart your phone once
Sent from my SM-G925F using XDA Free mobile app
I found that mine was doing the same. I turned off the Connections Optimizer and now my wife stays off. Nice idea but poorly executed.
carrsteven said:
I found that mine was doing the same. I turned off the Connections Optimizer and now my wife stays off. Nice idea but poorly executed.
Click to expand...
Click to collapse
Thx. I Actually realized that was the problem As well
Where did you find this "Connections Optimizer" setting because I can't find it on my Vodafone S6. I've tried every possibile setting to stop my Edge connecting every 3-4 hours to Wifi but no luck at all. Thanks
wifi wont turn on and bluetooth wont turn on
hello , i have a problem with S6, after i flash a new firmware my wifi and bluetooth wont turn on , i had a bootloop some days before and i erase the os by mistake, but now i managed to flash the os and i see theres no bootloop anymore but i can't turn on the wifi and bluetooth, i tried wipe the cache and data factory reset and still nothing , any advice ?thankyou
Hi Guys,
I am facing a problem with the WiFi staying on on my brand new xz1.
In the Wifi preferences, under Advanced preferences, if i select "Never" for the option "Keep WiFi on during sleep", i have noticed that the Wifi turns off when the phone goes in sleep mode.
But the problem is that it does not turn back on. It stays off until i turn it back on.
Does anyone else also experience this or is my understanding off somewhere?
Thanks,
Prasad
No one else is experiencing this?
What could I be doing wrong or maybe i have set this wrong?
Any help guys?
Nope. I even noticed that since the latest update for my Z5 that wifi kinda doesn't work even tho it shows as connected after the phone has entered sleep. My XZ1 does the same. I'm assuming it's some new android power saving? My As soon as I unlock everything works fine again but if I'm downloading torrents or streaming movies to my tv i need to keep the phone plugged in so it doesn't sleep
pdash79 said:
Hi Guys,
I am facing a problem with the WiFi staying on on my brand new xz1.
In the Wifi preferences, under Advanced preferences, if i select "Never" for the option "Keep WiFi on during sleep", i have noticed that the Wifi turns off when the phone goes in sleep mode.
But the problem is that it does not turn back on. It stays off until i turn it back on.
Does anyone else also experience this or is my understanding off somewhere?
Thanks,
Prasad
Click to expand...
Click to collapse
If you select never it means: never keep wifi on during sleep = turn wifi off during sleep.
Select "always" if you want to have wifi always on.
pdash79 said:
Hi Guys,
I am facing a problem with the WiFi staying on on my brand new xz1.
In the Wifi preferences, under Advanced preferences, if i select "Never" for the option "Keep WiFi on during sleep", i have noticed that the Wifi turns off when the phone goes in sleep mode.
But the problem is that it does not turn back on. It stays off until i turn it back on.
Does anyone else also experience this or is my understanding off somewhere?
Thanks,
Prasad
Click to expand...
Click to collapse
The problem is your comprehension on the setting. Understand the setting and the options it is very clear once you understand the meaning of the setting.
You have set the phone to deny WiFi when screen off. Full stop
I experienced an issue on the first day where it would connect and then quickly disconnect while connecting to a public network. Haven't faced the issue since then again under the same circumstances.
dillalade said:
The problem is your comprehension on the setting. Understand the setting and the options it is very clear once you understand the meaning of the setting.
You have set the phone to deny WiFi when screen off. Full stop
Click to expand...
Click to collapse
Yes quite right.
I have set the phone tondeny wifi onky when the phone sleeps.
Does it bot mean then that when thw phone wakes up from sleep, the wifi should also turn back on?
That is how it works on other android devices.
But with xz1 once the device goes to sleep, wifi shuts down which is good.
But when i wake the device, wifi stays off. It does not turn back on.
Thanks for reading.
pdash79 said:
Yes quite right.
I have set the phone tondeny wifi onky when the phone sleeps.
Does it bot mean then that when thw phone wakes up from sleep, the wifi should also turn back on?
That is how it works on other android devices.
But with xz1 once the device goes to sleep, wifi shuts down which is good.
But when i wake the device, wifi stays off. It does not turn back on.
Thanks for reading.
Click to expand...
Click to collapse
I see.
Not noticed anything like this.
However I have the same setting applied (WiFi off during sleep.)
So I'll test this later and report back.
dillalade said:
I see.
Not noticed anything like this.
However I have the same setting applied (WiFi off during sleep.)
So I'll test this later and report back.
Click to expand...
Click to collapse
Thanks buddy
pdash79 said:
Thanks buddy
Click to expand...
Click to collapse
It works for me dude. WiFi signal reconnects as expected when screen is turned back on after a sleep.
All I can say is Sony's OTA updates since even my z3 have always caused issues. Try a factory reset.
Thanks for testing it out and glad to know there is no issue.
Will do a reset soon enough and report back though it might take a while as i am travelling.
dillalade said:
It works for me dude. WiFi signal reconnects as expected when screen is turned back on after a sleep.
All I can say is Sony's OTA updates since even my z3 have always caused issues. Try a factory reset.
Click to expand...
Click to collapse
Cool bro.
The reset fixed it.
Now it works.
Thanks for your suggestion.
Sweet!
Possible solution
pdash79 said:
Hi Guys,
I am facing a problem with the WiFi staying on on my brand new xz1.
In the Wifi preferences, under Advanced preferences, if i select "Never" for the option "Keep WiFi on during sleep", i have noticed that the Wifi turns off when the phone goes in sleep mode.
But the problem is that it does not turn back on. It stays off until i turn it back on.
Does anyone else also experience this or is my understanding off somewhere?
Thanks,
Prasad
Click to expand...
Click to collapse
Try turning off data. There is a setting that keeps the lte active for faster network switches. I have same issue. Don't notice it when data is off.
I am suffering the same Wi-Fi issue. It is only since the recent update this has occurred. I've contacted Sony to no avail. It's driving me mad.
Same here (FW:47.1.A.12.145) WIFI router is with atheros chipset.
When phone is going to "sleep" wifi is switching off (even if it is set to not do so).
It seems that flushing cache partition is fixing it for some time.
Hi all!
I faced a problem after installing the latest update from the Mi Fit official app.
Amazfit Bip is stuck on "smartphone <--> watch"
The watch at night decided to update, the phone was in power saving mode and apparently the update hung in the process.
Now on the watch screen only one picture as on an attached screenshot "smartphone <--> watch"
I have been installed several fw's, .res and .gps files by Gadget Bridge (from 0.0.9.49 to 0.1.0.45) tried 20 times but after flashing "smartphone <--> watch" screen appears again.
Now watches works like 1st Mi Band (steps taken appears in Mi Fit app)
Any idea how this can be fixed?
Thank you in advance!
http ://prntscr.com/i2pq06
Partially repaired by downgrading fw to v.0.0.8.74. In this fw watches display works correctly (shows time and I can switch menus). Upgrading to fw above 0.0.8.74 leads to stuck display.
Did you try to set the system language (temporarily) to english? You have no location in your profile so I could only guess. The german mi fit app seems to have this error, too, and un-/re-pairing after setting system language to english is a temporary fix here. Its annoying because after the next update - sometimes agps sync is enough to trigger it - the same error occurs again.
deppjones said:
Did you try to set the system language (temporarily) to english? .
Click to expand...
Click to collapse
thank you - problem solved after autoupdate to 0.1.0.80
Good to hear. My problems started with 0.1.0.80, too
hi. also happaned to me!!! can u write down how did u fixed this please ?
Shure
yuvalhaim said:
hi. also happaned to me!!! can u write down how did u fixed this please ?
Click to expand...
Click to collapse
Unpair Amazfit BIP from the mi fit app (at the bottom of the device settings screen).
Close mi fit app.
Switch system language to english (somewhere in the phone's settings, differs from device to device).
Start mi fit app.
Connect Amazfit BIP with mi fit app (if you don't have any other smart devices connected, this should be accessible from the first screen).
Confirm connection on the BIP.
Wait for any update/GPS/AGPS/sync to be finished.
The Amazfit BIP should now work. Maybe some settings have been reset and the watchface is back to default.
It should be safe to switch the system language back to what it was.
This fix is not permanent. It happened again, when I changed some settings and alarms in the mi fit app, and after an AGPS update (this should be made optional!). But I could not nail down the trigger, as it's running as expected now. I don't know if that's applicable for other languages as well as I only use german - and english for short periods lately.
hi
did the folwoing steps but still dispaly the parring pic,
please any other ideas?
deppjones said:
Unpair Amazfit BIP from the mi fit app (at the bottom of the device settings screen).
Close mi fit app.
Switch system language to english (somewhere in the phone's settings, differs from device to device).
Start mi fit app.
Connect Amazfit BIP with mi fit app (if you don't have any other smart devices connected, this should be accessible from the first screen).
Confirm connection on the BIP.
Wait for any update/GPS/AGPS/sync to be finished.
The Amazfit BIP should now work. Maybe some settings have been reset and the watchface is back to default.
It should be safe to switch the system language back to what it was.
This fix is not permanent. It happened again, when I changed some settings and alarms in the mi fit app, and after an AGPS update (this should be made optional!). But I could not nail down the trigger, as it's running as expected now. I don't know if that's applicable for other languages as well as I only use german - and english for short periods lately.
Click to expand...
Click to collapse
yuvalhaim said:
hi
did the folwoing steps but still dispaly the parring pic,
please any other ideas?
Click to expand...
Click to collapse
Sorry, no idea. If you did the unpairing before the language switching and then the re-pairing, it should partly reset the BIP (but no factory reset, that could only be done from the watch menu).
It's a pity, they did not build in a way to shut down the watch. Some people reported, that after the watch completely drained its battery,, it worked afterwards (but maybe only until the next sync).
Better write to huami for a fix to that.
Btw. I had to reconnect my watch two times today, so I better leave the mi app alone until I get home or my goal is finished. The re-pairing and agps update drains my phone battery quit a lot.
deppjones said:
Sorry, no idea. If you did the unpairing before the language switching and then the re-pairing, it should partly reset the BIP (but no factory reset, that could only be done from the watch menu).
It's a pity, they did not build in a way to shut down the watch. Some people reported, that after the watch completely drained its battery,, it worked afterwards (but maybe only until the next sync).
Better write to huami for a fix to that.
Btw. I had to reconnect my watch two times today, so I better leave the mi app alone until I get home or my goal is finished. The re-pairing and agps update drains my phone battery quit a lot.
Click to expand...
Click to collapse
Unistall MiFit.
Try to install this one :
https://www.apkmirror.com/apk/anhui-huami-information-technology-co-ltd/mi-fit/
Connect and wait.
Kéno40 said:
Unistall MiFit.
Try to install this one :
https://www.apkmirror.com/apk/anhui-huami-information-technology-co-ltd/mi-fit/
Connect and wait.
Click to expand...
Click to collapse
Thanks, but that's exactly the version I am running and that triggered the (buggy) firmware update in the first place.
I have a shortcut for my workaround. While the bug is triggered by any sync apart from steps, it also occurs when notifications are deleted from the watch. I set my phone to english and it seems to be enough to switch bluetooth off and on to reactivate the watch (on my german phone).
That way I don't loose the step counter and settings on the watch. Not that much of a hassle as before, but still annoying. I hope for an update of the firmware soon. Does anybody know a kontact to huami for the BIP? I just found one for the Pace and the Arc, but nothing for the BIP.
A was able to "unstuck" my Bip. Here are my steps:
1. unpair watch
2. Switch phone do English UK
3. Reboot phone
4. Pair watch again with Mi Fit app -> I was able to pair my watch on 2nd try. You should see now a time on display (after update of AGPS).
5. Switch phone back to your language
I think, we have to wait for an update for the firmware. Please report this bug via the mi fit app (the reporting function is a little bit buggy as it requires several tries most of the time). You can include the watch logs as well, maybe that helps to eliminate this bug.
My workaround is rather quick - close mi fit app if open, set phone language to English, wait for the phone to rearrange things, disable bluetooth, wait a short time, enable bluetooth, tap amazfit watch in list, start mi fit app, watch back working without settings and steps lost.
I admit, I am too lazy for that, so I just leave the phone set to englisch until this is sorted out...
deppjones said:
Sorry, no idea. If you did the unpairing before the language switching and then the re-pairing, it should partly reset the BIP (but no factory reset, that could only be done from the watch menu).
It's a pity, they did not build in a way to shut down the watch. Some people reported, that after the watch completely drained its battery,, it worked afterwards (but maybe only until the next sync).
Better write to huami for a fix to that.
Btw. I had to reconnect my watch two times today, so I better leave the mi app alone until I get home or my goal is finished. The re-pairing and agps update drains my phone battery quit a lot.
Click to expand...
Click to collapse
Same issue with my brand new BIP i have just received yesterday.
After pairing, it syncs with the Mi Fit app but the screen stuck in the phone <--> watch screen.
I changed the phone language to English (from Hungarian), pairing is fully done now with watch screen nicely working too.
Anybody ideas on why this is happening and how it should be resolved?
---------- Post added at 07:45 AM ---------- Previous post was at 07:40 AM ----------
xIndian said:
A was able to "unstuck" my Bip. Here are my steps:
1. unpair watch
2. Switch phone do English UK
3. Reboot phone
4. Pair watch again with Mi Fit app -> I was able to pair my watch on 2nd try. You should see now a time on display (after update of AGPS).
5. Switch phone back to your language
Click to expand...
Click to collapse
Hey Xindian, is this proved to be a permanent resolution for you?
I made the same process yesterday with success, and today morning I woke up with the stuck watch screen again
Kawitan said:
Hey Xindian, is this proved to be a permanent resolution for you?
I made the same process yesterday with success, and today morning I woke up with the stuck watch screen again
Click to expand...
Click to collapse
My watch are OK. But I didn't open Mi Fit app yet... I'll try later.
hi i try to do the same process but the problem remain!
the paring pic is still alwayes dispaly. (phone is parring ok to the watch, can find it , can see the steps ect )
xIndian said:
My watch are OK. But I didn't open Mi Fit app yet... I'll try later.
Click to expand...
Click to collapse
yuvalhaim said:
hi i try to do the same process but the problem remain!
the paring pic is still alwayes dispaly. (phone is parring ok to the watch, can find it , can see the steps ect )
Click to expand...
Click to collapse
I am having the same problem. Stuck in the "pairing screen". What can I do?
I also had the same problem in my OnePlus phone. My language was already English. Suddenly watch displayed Spanish language error saying asking to reconnect to phone.
I tried all the above methods but nothing worked even after multiple restarts and unpair/uninstall and watch still showing same error
I paired the watch with different smartphone. At that time it updated resources and agps then mi fit keeps crashing again
Don't know what to do and watch has more than 75 percent battery also. This is becoming really annoying. Not expected from a manufacturer like xiaomi
Sent from my ONEPLUS A5000 using Tapatalk
rstheboss said:
I also had the same problem in my OnePlus phone. My language was already English. Suddenly watch displayed Spanish language error saying asking to reconnect to phone.
I tried all the above methods but nothing worked even after multiple restarts and unpair/uninstall and watch still showing same error
I paired the watch with different smartphone. At that time it updated resources and agps then mi fit keeps crashing again
Don't know what to do and watch has more than 75 percent battery also. This is becoming really annoying. Not expected from a manufacturer like xiaomi
Sent from my ONEPLUS A5000 using Tapatalk
Click to expand...
Click to collapse
I have exactly the same problem. The App crashes directly after syncing on 2 phones...
Kawitan said:
Hey Xindian, is this proved to be a permanent resolution for you?
I made the same process yesterday with success, and today morning I woke up with the stuck watch screen again
Click to expand...
Click to collapse
Sadly, I am back - stuck on sync screen... We have to wait for next update i think.
Hi guys,
since I updated my Amazfit Pace to firmware version 1.3.7 I not able to connect via Bluetooth. My Amazfit is not showing up if I´m searching for bluetooth devices near to my phone. I tried it with a android and iOS device. If I´m searching for devices on my amazfit than it shows up my smartphones.
Did anyone know this issue? Is it possible to enable / disable BT on my Amazfit Pace?
Regards,
Tobi
I think the watch is only discoverable when the QR code is shown. So i think you can try a factory reset, to get it to reboot and show the QR code and scan it with the app and re pair to your phone. Also while it factory resets unpair it from the phone, from settings and app.
The watch is never "discoverable", that's why you use the QR code to pair, and only then it shows in phone's BT settings.
Are you using a custom ROM on your phone? Try a reboot on your phone and your watch again. I had the same problem as you and I've found that my phone was the problem, seemed like my device wasn't acutally enabling bluetooth therefore it couldn't connect to the watch.
Same problem for me too
After updated to 1.3.7
Not discoverable in phone Bluetooth settings
Unpaired in watch app & forget in phone Bluetooth settings
After factory reset the watch
Not able to pair
Showing message like
Bluetooth on watch is turn off
Please try again later
If anyone found the solution help me out
Shiva Chandran said:
Same problem for me too
After updated to 1.3.7
Not discoverable in phone Bluetooth settings
Unpaired in watch app & forget in phone Bluetooth settings
After factory reset the watch
Not able to pair
Showing message like
Bluetooth on watch is turn off
Please try again later
If anyone found the solution help me out
Click to expand...
Click to collapse
Try this:
https://forum.xda-developers.com/showpost.php?p=76680707&postcount=19
lfom said:
Try this:
https://forum.xda-developers.com/showpost.php?p=76680707&postcount=19
Click to expand...
Click to collapse
Unpaired
Factory reset
Watch Bluetooth is not showing in both android 6.0 and iOS 11.3
Scan tge QR code
“Bluetooth on watch is turn off,
Try again later “
This message only comes
Shiva Chandran said:
Unpaired
Factory reset
Watch Bluetooth is not showing in both android 6.0 and iOS 11.3
Scan tge QR code
“Bluetooth on watch is turn off,
Try again later “
This message only comes
Click to expand...
Click to collapse
This started after you updated the watch to 1.3.7? This is weird... You can try downloading a Chinese version of Amazfit app, some people reported that they could pair using this version in cases like yours...
lfom said:
This started after you updated the watch to 1.3.7? This is weird... You can try downloading a Chinese version of Amazfit app, some people reported that they could pair using this version in cases like yours...
Click to expand...
Click to collapse
I tried with Chinese Amazfit app also lastest and 1.7.0 version also not working for me
toto1988 said:
Hi guys,
since I updated my Amazfit Pace to firmware version 1.3.7 I not able to connect via Bluetooth. My Amazfit is not showing up if I´m searching for bluetooth devices near to my phone. I tried it with a android and iOS device. If I´m searching for devices on my amazfit than it shows up my smartphones.
Did anyone know this issue? Is it possible to enable / disable BT on my Amazfit Pace?
Regards,
Tobi
Click to expand...
Click to collapse
AmazfitPAce Tuner APK v1.1 - allow to enable/disable Bluetooth.
Thanks. This worked!
lfom said:
Try this:
https://forum.xda-developers.com/showpost.php?p=76680707&postcount=19
Click to expand...
Click to collapse
Turning Airplane mode on for the watch, reinstalling the Amazfit Verge app, then turning Airplane mode on, indeed prompted the pair request with the pair codes on both the phone and watch. Thanks for the help! I wasn't about to factory reset my watch if I didn't have to.
What I Did and works
Hi,
I have tried some topics from internet but nok.
I did these above steps and work for me:
1- Turn watch to airplane mode;
2- Clear bluetooth cache and data (Android/ IOS). It's not necessary to remove the watch from bluetooth devices list.
3- Reinstalling the Amazfit app;
4- Turn off the airplane mode (watch).
5- Done! Make login in the Amazfit app and both devices will be sync data now.
cabaltom said:
Turning Airplane mode on for the watch, reinstalling the Amazfit Verge app, then turning Airplane mode on, indeed prompted the pair request with the pair codes on both the phone and watch. Thanks for the help! I wasn't about to factory reset my watch if I didn't have to.
Click to expand...
Click to collapse